COLOR TOUCH SCREEN CONTROLLER (CTP)

Transcription

1 OLOR TOUH SRN (TP) OPRTIONL GUI olor Touch Screen ontroller with Power Supply: Programmable X lighting controller for RG fixtures. Lighting effects can be accessed and modified with the touch sensitive screen. uilt in clock and calendar allows scheduled events to trigger custom lighting effects. omes ready to mount onto a standard U.S. single gang switch box or two gang wall box. 9V Power dapter is included and fits discreetly inside the Junction ox behind the controller. ompatible With: Remote ynamic olor hanging Power Supplies with X. lue L is used to indicate wheather the unit is on or off. uttons -8 are used to select individual scenes. Scenes can be static or dynamic. ouble pressing buttons -8 will reset the immer, Speed, and olor to default. Used to cycle between different pages (,,,, x). In combination with buttons -8, 00 different scenes can be stored. The select button allows you to cycle through the immer, Speed, and olor fader controls. The fader at the bottom of the unit is used to select the intensity of the immer, Speed, and olor settings. The green L indicates that the immer, Speed, and olor settings on the STIK are set to default. If the fader is moved to the right or left of the default (green), one of the 8 blue L s will indicate your current intensity level. The colorized fader offers a direct access to basic colors with a simple touch. RV W. ullerton hicago, IL 606 Ph: ax: info@puredgelighting.com 06 Puredge Lighting. ll Rights Reserved.

2 - + 0 dge Lighting. ll Rights Reserved. 78 W. ullerton ve hicago, IL 606 Tel: ax: info@edgelighting.com Installation Instructions for TP olor Touch Screen ontroller with Power Supply INT INORTION - This instruction shows a typical installation.. SV THS INSTRUTIONS! TP 90-TP Installing TP Panel : On the selected wall, install deep double gang boxes to fit the controller and controller power supply (OT recommended). P LTRIL OX WLL SUPPLY : On the selected wall, install deep double gang boxes to fit the controller and controller power supply (OT recommended). WLL dimmer speed color 8 6 SLT 7 : Remove the back panel of the TP controller to attach power supply and X controller cables. TP - + K PNL

3 : onnect light green 9 pin power supply header to corresponding 9-Pin green port on the back of TP module. : Splice 0V power supply input cable and run blue and brown line voltage wires through conduit to line and neutral wires in wall. 6: onnect blue wire to neutral wire in wall 7: onnect brown wire to line wire in wall GROUN 0 8 X X GROUN - 9 X + NOT: heck pin configurations. pplying power to the X input will damage the controller. 8: onnect one end of a data wire (blue with white stripes wire) to controller "X " terminal : onnect one end of a data wire (white with blue stripes wire) to controller "X+" terminal. 0: onnect one end of a data wire (bare shield wire) to controller "X GROUN" terminal. X L (LN #98)

4 NOT: "X in+", "X in-", "XT in+" & "XT in-", controller terminals are not used on controller. : onnect one end of a data wire (blue with white stripes wire) to controller "LSYN OUT " terminal. onnect the other end into the VR-RG-60 "X in " terminal. X L (LN #98) : onnect one end of a data wire (white with blue stripes wire) to controller "LSYN OUT+" terminal. onnect the other end into the VR-RG-60 "X in +" terminal. : onnect one end of a data wire (bare shield wire) to controller "LSYN SHIL" terminal. onnect the other end into the VR-RG-60 "X in shield" terminal. xt in- xt in+ V+ V- X in + X in - X in shield LedSync thru+ LedSync thru- LedSync shield G : Run the line voltage power wires into the power supply. : onnect the hot power wire to black power supply wire and black wire coming from the controller power supply with a wire nut. 6 6: onnect the neutral power wire to white power supply wire and white wire coming from the controller power supply with a wire nut. 7 7: ake sure the green transformer wire is grounded in accordance with local electrical codes.

5 H NOT: TP controller uses S-PRO software on. 8: Reference provided for TP software and instructions on programming the controller.