ACCESS CONTROL STARTER KIT HARDWARE INSTALLATION GUIDE

Transcription

1 ACCESS CONTROL STAR KIT HARDWARE INSTALLATION GUIDE

2 READ THIS BEFORE YOU START This document contains a lot of useful information to help you install and configure the Stanley Starter and Expansion Kit as effectively as possible. If you cannot read the entire document then at least take note of the points in the box below - Thank You. IMANT POINTS: Check the power supply voltage for each unit. It is factory set to 2V. If you are using 24V locks then set the jumper on the power supply to 24V. If you set the power supply to 24V then make sure the readers you are using will operate at that voltage. The GS3 readers supplied in these kits will work, but other readers may not. You may need to use an extra power supply. Review the reader wiring for the GS3 readers you may not be familiar with the PAC signal connection that only requires one data conductor. Make sure you have the Stanley Screwdriver supplied with the Starter Kit, it is the correct size for the reader terminal block screws Check the current PC Operating System requirements before attempting to install the Stanley PAC software. Supported operating systems are listed at WHAT ELSE DO I NEED? A Windows PC computer. A network to connect to the PAC 52IP (Existing or one you install). Locks for the controlled doors. These could be strikes or mag locks, or they could be barriers or gates. Optional door contacts and request-to-exit devices. Backup batteries there is room in the enclosure for one 2v 7Ah or two 2v 4.5Ah. Wiring Requirement RS CAT5 or CAT6 cable Readers - 22AWG 4-Conductor, Unshielded and Stranded STEP INSTALLATION - TEST MODE TESTING One Person Installation Testing at the Door. Press the door controller s One Touch button for 4 seconds to activate test mode for one hour. All the readers attached to this controller will latch from red to green. All feedback is provided by the reader. To exit hold 'One Touch' button for 4 seconds or it will time out after hour. Present this card to the Entry Reader. Reader will flash from green to red once and the lock will release. Present this card to the Exit Reader. Reader will flash from green to red twice and the lock will release. Operate the Request-to-Exit (/REX). Reader will flash from green to red three times. Open the Door Contact. Reader will flash from green to red four times. Default state STEP - TEST MODE INSTALLATION TESTING One Person Installation Testing at the Door. Press the door controller s One Touch button for 4 seconds to activate test mode for one hour. All the readers attached to this controller will latch from red to green. All feedback is provided by the reader. To exit hold 'One Touch' button for 4 seconds or it will time out after hour. Present this card to the Entry Reader. Reader will flash from green to red once and the lock will release. Present this card to the Exit Reader. Reader will flash from green to red twice and the lock will release. Operate the Request-to-Exit (/REX). Reader will flash from green to red three times. Open the Door Contact. Reader will flash from green to red four times. The One-Touch Test Mode card included with each Starter Kit, enables the testing of all door hardware by just one person, at the door. Default state

3 Hardware Installation WHAT S IN THE BOX? Congratulations on choosing the Stanley PAC Two-Door Starter Kit access control and security solution. This Installation Manual explains how to install the Starter Kit hardware. The Two-Door Starter Kit controls two sets of door devices (such as two-doors, two-readers and door contact inputs) with Card In/Card Out (a reader on both sides of the same door). Up to 23 Stanley Expansion Kits can be connected to each Starter Kit using RS-485, enabling control of 48 doors. STANLEY STAR KIT STANLEY EXPANSION KIT Controller INPUT: ; 0.8A (CONTROLLER ONLY) RX RS-232 DTR includes: Metal Enclosure Power Supply 2-Door Controller CTS TX Serial No. PAC Part No. Serial No. PAC Part No. INSP E/BOND TESTED HIP OT BURN MOD LEVEL INSP F/INPS FLASHING MAINS ONLY STEADY MAINS & BATTERY E/BOND TESTED HIP OT BURN MOD LEVEL GLU/LID F/INPS GLU/LID MAX OUTPUT POWER : MAX OUTPUT POWER : MAX INPUT CURRENT : MAX INPUT CURRENT : MAINS INPUT VOLTAGE : VAC 47-63Hz MAINS INPUT VOLTAGE : VAC 47-63Hz DANGER DO T CONNECT TO MAINS SUPPLY UNTIL CORRECTLY INSTAL FLASHING MAINS ONLY MAINS & BATTERY STEADY DANGER DO T CONNECT TO MAINS SUPPLY UNTIL CORRECTLY INSTAL Boxed Stanley PAC 52IP Boxed Stanley PAC 52 2x Stanley GS3 Readers 2x Stanley GS3 Readers Readers Windows PC Software Stanley PAC Access Lite Edition on USB Flash Drive USB Admin Reader includes USB Cable and Driver Stanley GS3 USB Admin Reader Key Fobs Stanley Key fobs - 0 Pack Non Secure side Secure side 52IP Access Controller STANLEY PAC USB Stick ➋ Door contact DTR RX CTS TX Serial No. PAC Part No. ➌ Mullion Reader SEA RECHARGEABLE LEAD-ACID BATTERY 2V BATTERY REX ➊ ➎ Key Fob LAN Windows PC Admin Reader ➍

4 STAR KIT PNTS The Starter Kit consists of the following equipment: ➊ STANLEY PAC ACCESS LITE EDITION SOFTWARE. Stanley PAC Access software is designed to run on Windows PC with Windows 0, Windows 8. or Windows 7 operating system. Support is also available for Windows Server, SQL Server and Virtual Machine installations. Refer to for complete information. The Lite Edition will organise and report on up to 5,000 users and 28 doors. There are four versions of the software, a simple software activation key is all that required to upgrade from version to version. ADV PRO 5

5 INSP E/BOND TESTED HIP OT BURN F/INPS MAX OUTPUT POWER : MAX INPUT CURRENT : MAINS INPUT VOLTAGE : VAC 47-63Hz FLASHING MAINS ONLY STEADY MAINS & BATTERY Serial No. PAC Part No. DANGER DO T CONNECT TO MAINS SUPPLY UNTIL CORRECTLY INSTAL GLU/LID TERM IN OUT N N0 NGND OVRD VIN LOCK TX RX TX RX ADMIN INPUT: ; 0.22A (CONTROLLER + 4 S) CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Manufacture Date One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. Made in UK SEA RECHARGEABLE LEAD-ACID BATTERY SIGNAL VOLTAGE 2/24V 5V DATA DOOR 2 DOOR2 SEA RECHARGEABLE LEAD-ACID BATTERY STAR KIT PNTS ➋ TWO-DOOR CONTROLLER (PAC 52IP WITH 3A POWER SUPPLY/CHARGER IN METAL ELOSURE) Both the Starter Kit and Expansion Kit are supplied with a Two-Door Controller mounted on stand-offs, tamper switch and 3A 2 or 24V switchable power supply, enclosed in a lockable cabinet with two keys. The power supply/charger provides power for the controller providing access control for up to two doors, with four readers (Entry/Exit) and most locks. 5Year Warranty There is space for one 2V, 7AHr or two 2V 4.5AHr (wired in series) sealed lead-acid batteries. These provide standby backup power, depending upon system configuration and activity. The power supply has deep discharge protection, and provides a Low Battery signal to the panel. Replace the batteries every 2 to 3 years, or more often if the system has a high rate of backup use. 0.2 A MAX RS-485 MOD LEVEL TCP/IP POWER ACCESS AC 52 IP Mk. 2 Access Controller 2V BATTERY DOOR 0.2 A MAX DOOR 2 LOCK 2 LOCK RELAY 30 V; 5A RELAY 2 30 V; 5A 2V BATTERY ELOSURE The enclosure is 3.5 inches wide, 3.5 inches high, 3.5 inches deep. The Door Controller is mounted directly to the enclosure with stand-offs. All the Stanley PAC 52 series controllers and Stanley GS3 Readers can be powered from a supply between 0.5 and 28V. CURRENT CONSUMPTION PAC 52 & 52IP Readers Locks Other Devices 220mA GS3 Mullion 00mA (0.A) per reader. Reader power is limited to 200mA per door. Check the manufacturer's data sheet. Check current consumption of any other devices such as motion s if they are to be powered from the same supply. The reader power supply voltage is the same as the input voltage. If you are using a 24V supply to power the 52 door controller and not using Stanley GS3 readers, make sure the readers are capable of being powered at this voltage. 6

6 STAR KIT PNTS ➌ STANLEY GS3 MULLION PROXIMITY Perfect for narrow rail mullion installations and can be used as an unobtrusive unit for standard wall mounted reader applications..9in.in The reader uses one screw to attach the reader to the mounting bracket, allowing easy mounting indoors or out. SUPS 2 24 OR VOLTS Each reader is outfitted with an integrated piezo buzzer, bicolor and has a read range of up to 3 in. 4.in.8in.07in 0.98in 3.96in 3.27in 0.79in 0.70in.63in ➍ STANLEY GS3 USB ADMIN The USB Admin Reader is designed to to sit next to the Host or a Client PC and connected with the supplied USB cable to a USB port. This reader is designed to ease the task of enrolling credentials. Card numbers are read directly into the Stanley PAC Access database. 3.46in..22in. Additional workstations can also have Enrollment Readers. The Lite Edition supports 2 clients, but more can be added with a software license upgrade. 5.2in. 7

7 STAR KIT PNTS ➎ STANLEY PROXIMITY KEY FOBS, BOX OF 0 Robust, world-class construction combined with advanced technology and a pre-programmed unique identification number without site codes, makes programming easy and copying almost impossible. Every key fob is manufactured using a highly sophisticated process. Ultrasonic welding closes the housing, ensuring a highly reliable product. The passive proximity technology in the key fob requires no batteries or physical contact with the reader; this helps assure that the key fobs are virtually wear-free and will provide years of service with no maintenance..3in. 0.24in. 2.36in. STANLEY PROXIMITY ISO PROXIMITY CARDS, PACK OF 0 ** Not supplied with the Starter Kit. ADI # 7S-STCARD The Stanley ISO Proximity Card offers proximity technology with photo identification capability on a single card. It is ISO 780 compliant, with a nominal thickness of.030", the same size and thickness as a standard credit card. The card features a graphics quality surface optimized for Photo ID printing and vertical or horizontal slot punch capability in. 2.25in in ± 0. 8

8 DOOR TX RX TX RX IN OUT DOOR TX RX TX RX IN OUT N N DOOR TX RX TX RX IN OUT RS A MAX N0 NGND RS A MAX N0 NGND N RS A MAX N0 NGND DOOR LOCK RELAY 0.2 A MAX DOOR 2 LOCK 2 CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. OVRD This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation TCP/IP DOOR LOCK RELAY 0.2 A MAX DOOR 2 LOCK 2 CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. OVRD This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation TCP/IP POWER POWER RELAY 2 ACCESS VIN LOCK RELAY 2 ACCESS VIN LOCK DOOR LOCK RELAY 0.2 A MAX DOOR 2 LOCK 2 CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. OVRD This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must TCP/IP accept any interference received, including interference that may cause undesired operation POWER RELAY 2 ACCESS VIN LOCK 2 2/24V 5V DOOR2 DATA 2 2/24V 5V DOOR2 DATA 2 2/24V 5V DOOR2 DATA DOOR TX RX TX RX IN OUT N RS A MAX N0 NGND DOOR TX RX TX RX IN OUT N RS A MAX N0 NGND DOOR LOCK RELAY 0.2 A MAX DOOR 2 LOCK 2 CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. OVRD This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation RS-232 DTR RX CTS TX DOOR LOCK RELAY 0.2 A MAX DOOR 2 LOCK 2 CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. OVRD This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation RS-232 DTR RX CTS TX POWER RELAY 2 ACCESS VIN LOCK 2 2/24V 5V DOOR2 DATA DOOR TX RX TX RX IN OUT N RS A MAX N0 NGND DOOR LOCK RELAY 0.2 A MAX DOOR 2 LOCK 2 CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. OVRD This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation RS-232 DTR RX CTS TX POWER RELAY 2 ACCESS VIN LOCK 2 2/24V 5V DOOR2 DATA INSTALLATION PAC 52IP There two typically site layouts, using Stanley PAC 52-series Two-Door Controllers. The Starter Kit acts as the TCP/IP gateway for a RS485 multi-drop of Two-Door Expansion Kits. Up to 23 Expansion Kits can be added to give a maximum of 24 controllers with 48 doors on a single bus. LAN/WAN PAC 52IP 2 DOOR CONTROLLER (STAR KIT) ADMIN TERM INPUT: ; 0.22A (CONTROLLER ONLY) Made in UK PAC 52IP Mk. II Access Controller X Date Code One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SIGNAL VOLTAGE PAC 52 2 DOOR CONTROLLER (EXPANSION KIT) ADMIN TERM INPUT: ; 0.22A (CONTROLLER ONLY) Made in UK PAC 52 Mk. II Access Controller X Date Code One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SIGNAL VOLTAGE PAC 52 2 DOOR CONTROLLER (EXPANSION KIT) ADMIN TERM INPUT: ; 0.22A (CONTROLLER ONLY) Made in UK PAC 52 Mk. II Access Controller X Date Code One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SIGNAL VOLTAGE UP TO 24 CONTROLLERS [TOTAL] (RS-485 MUNICATIONS) DOOR DOOR TWO DOOR DOOR TWO DOOR DOOR TWO 2. Larger systems spread across several sites can be created by using multiple network connections PAC 52IP 2 DOOR CONTROLLER (STAR KIT) TERM ADMIN INPUT: ; 0.22A (CONTROLLER ONLY) POWER RELAY 2 ACCESS VIN LOCK One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. Made in UK PAC 52IP Mk. II Access Controller X Date Code 2 SIGNAL VOLTAGE 2/24V 5V DOOR2 DATA TERM IN OUT TX RX TX RX CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Made in UK 2/24V 5V DATA DOOR TX RX TX RX IN OUT N RS A MAX N0 NGND DOOR LOCK RELAY 0.2 A MAX DOOR 2 LOCK 2 CAUTION - FIXED INTERNAL BATTERY See manual for disposal of unit. OVRD This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must TCP/IP accept any interference received, including interference that may cause undesired operation DOOR 2 DOOR2 POWER RELAY 2 ACCESS VIN LOCK 2 2/24V 5V DOOR2 DATA PAC 52 2 DOOR CONTROLLER (EXPANSION KIT) TERM ADMIN INPUT: ; 0.22A (CONTROLLER ONLY) Made in UK PAC 52 Mk. II Access Controller X Date Code One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SIGNAL VOLTAGE Location One DOOR DOOR TWO DOOR DOOR TWO PAC 52IP 2 DOOR CONTROLLER (STAR KIT) LAN/WAN ADMIN TERM INPUT: ; 0.22A (CONTROLLER ONLY) Made in UK PAC 52IP Mk. II Access Controller X Date Code One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SIGNAL VOLTAGE Location Three DOOR DOOR TWO HOST PC USB ADMIN ADMIN TERM INPUT: ; 0.22A (CONTROLLER ONLY) Made in UK PAC 52IP Mk. II Access Controller X Date Code One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SIGNAL VOLTAGE Location Two DOOR DOOR TWO PAC 52IP 2 DOOR CONTROLLER (STAR KIT) ADMIN N N0 NGND RS-485 INPUT: ; 0.22A (CONTROLLER + 4 S) 0.2 A MAX WORK CONNECTION The PAC 52IP controller can connect direct to the local network. Use a Cat 5 or Cat 6 patch cord. The distance from the PAC 52IP to the network outlet should be no longer than 30 feet. CAT 5 patch cord Max. 33 feet to outlet OVRD TCP/IP VIN LOCK Manufacture Date POWER ACCESS AC 52 IP Mk. 2 Access Controller One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SIGNAL VOLTAGE DOOR 0.2 A MAX DOOR 2 LOCK 2 DO D LOCK RELAY 30 V; 5A DO D RELAY 2 30 V; 5A SIGA SIGB SIGA SIGB

9 INSP E/BOND TESTED HIP OT BURN F/INPS MAX OUTPUT POWER : MAX INPUT CURRENT : MAINS INPUT VOLTAGE : VAC 47-63Hz FLASHING MAINS ONLY STEADY MAINS & BATTERY DANGER DO T CONNECT TO MAINS SUPPLY UNTIL CORRECTLY INSTAL GLU/LID I OUT N VIN LOCK RX TX RX T X Date Code One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SEA RECHARGEABLE LEAD-ACID BATTERY SIGNAL VOLTAGE 2/24V 5V DATA 0 I 2 DOOR2 SEA RECHARGEABLE LEAD-ACID BATTERY INSTALLATION CONTROLLER INSTALLATION Perform the following steps to install the PAC 52 Two-Door Controller: SUPS 2 24 OR VOLTS Warning: Use a static strap whenever touching the panel to ensure protection from Electrostatic Discharge (ESD).. Review the panel layout, cable runs, and power needs. OOR 2 Serial No. PAC Part No. MOD LEVEL POWER ACCESS LOCK 2 RELAY 2 2V BATTERY 2V BATTERY OPTIONAL 2V BACKUP X 2V 7aH BATTERY OPTIONAL 24V BACKUP 2x 2V 4.5aH BATTERIES 2. Mount the enclosure at the proper location on the wall. Use appropriate anchors for the mounting material. 3. Run all I/O wires to the enclosure, and properly mark each wire for its use. 4. The power supply should be connected to a grounded 20v AC outlet using the 3 Prong Universal Standard AC Power Cord provided. Caution: Do not apply power at this time. 5. Remove each green terminal connector one at a time to wire the properly labeled cables. See the wiring diagrams. Caution: Do not apply power at this time. 6. If you are using a battery backup function, place the one or two batteries in the enclosure 7. Attach the positive (red) Power Supply-to-Battery cable to the remaining positive (red) battery terminal. 8. Attach the negative (black) Power Supply-to-Battery cable to the remaining negative (black) battery terminal. 9. Apply power to the panel. and run One-Touch Test to check the system Operation. DO T APPLY AC POWER 0

10 INSTALLATION ELOSURE MOUNTING, BACK VIEW Two knock-outs are provided on each of the four sides of the enclosure, these are suitable for 3/4 EMT conduit. Cabinet Electrical Entries Enclosure Knock Outs Top 2 Bottom 2 Right Side 2 Left Side 2

11 INSP E/BOND TESTED HIP OT BURN F/INPS GLU/LID MAX OUTPUT POWER : MAX INPUT CURRENT : MAINS INPUT VOLTAGE : VAC 47-63Hz DANGER DO T CONNECT TO MAINS SUPPLY FLASHING MAINS ONLY UNTIL CORRECTLY STEADY MAINS & BATTERY INSTAL INSTALLATION POWER CONNECTION SUPS 2 24 OR VOLTS The 3A Power Supply is pre-wired in the metal enclosure. Output voltage is jumper-selectable to either 2 (factory setting) or 24V. This power supply can normally provide the controller, readers and lock power. Serial No. PAC Part No. TX RX TX RX IN OUT ADMIN TERM N INPUT: (CONTROLLER + RS-485 N0 NGND CAUTION - FIXED INT See manual for dis OVRD This device complies wi the FCC Rules. Operatio to the following two cond device may not cause h interference, and (2) this accept any interference including interference th undesired operation TCP/IP Made in Manufacture Date AC 52 IP Access Co One-Touch Testing To enter View Mode pre button momentarily. To e press and hold the Onefor 2 to 4 seconds. To le testing, press the button again. Note that One-To will automatically time o For details of One-Touch enclosed Quick Start Gu POWER ACCESS VIN LOCK SIGN 2/24 R MOD LEVEL or 24V Jumper 24V 2V PRE-WIRED FROM POWER SUPPLY 2 OR 24V The power supply includes battery charging at either 2 or 24V. The input indicates the AC Status to the controller, communicating when the power supply has switched from AC to battery. The PAC 52-series controllers draw 2V current. The total amount of current drawn by the controller will depend on the number and type of readers being used. AC POWER The power supply should be connected to a grounded 20v AC outlet using a power cord. A 3-Prong Universal Standard AC Power Cord is provided with the Kit. There are no fuses in the power supply, but it is protected against over current conditions and will cut out if the nominal limit is exceeded and reset once the load is removed. IMANT: To ensure reliable communications and protection from EMI and other transient effects, the controller must be connected to building ground. The power supply will have a ground conductor that leads to building ground through the AC supply. The controller is mounted using the six mounting holes which provide a ground to the enclosure. You should still ensure that the enclosure has a reliable path to building ground. 2

12 SECURITY ON INSTALLATION GS3 MULLION CONNECTION (PAC64 OUTPUT) When using Stanley PAC credentials these readers use a single data line (labeled SIG), using unshielded cable at up to 800ft. The PAC 52 controller can support one or two readers of this type per door. Potted electronics provide protection against inclement weather. Determine an appropriate mounting position on the door frame or wall. SINGLE This is the most common usage. Controller wiring 0.2 A MAX DOOR 2-24V D/SIG /GND D0/CLK SOUND C US LISTED 20 SECURITY ON CTS 52 PRODUCT SPECIFICATIONS (STANLEY PAC CREDENTIALS) Operating Voltage Range Max Current Requirements Max cable distance Cable Requirement Conductors Required 0.5 V to 28 V <00 Ma 800 ft PAC OUTPUT CABLING 22AWG, 6-conductor, stranded, unshielded 4 conductors (If REX and Door Contact not used) SUPS 2 24 OR VOLTS 22AWG 4-conductor stranded, unshielded cable from the controller, up to 800ft to the door. 4 Conductors for Stanley GS3 Mullion Reader TWO S ON A DOOR An optional second reader may be an exit reader or it could be a dual height or disabled entry reader. Locate readers at least 3ft apart to avoid interference. SIMPLE MY SAVING TIPS If you are using a Door Contact and REX, it is possible to use 22AWG 6-Conductor stranded, unshielded cable, if you share the ground wire () at the door. C US LISTED 0.2 A MAX DOOR 2 ON DO SIGA 2-24V D/SIG /GND D0/CLK SOUND Switch Settings for PAC64 Output Format When 3 rd party credentials are enrolled under PAC64 (eg. HID 25Khz Proximity) no change is rquired to the default setup. GS3 Mullion readers should be wired with 4-conductors and the reader type remains Stanley Proximity Reader. HID 346 ProxKey III HID386 ISOProx II Card 3

13 INSTALLATION CONNECTION DETAILS (PAC64 OUTPUT) Installation Notes:. The number of conductors required will depend on whether you are using a door contact and request to exit device. 2. After installation in wet or damp locations, it is good practice to seal the green connector well with electronics grade RTV silicone sealant to ensure that moisture cannot enter or accumulate in wiring compartments. Signal Description Power. The voltage at this terminal is the same as the voltage used to power the controller. Power is limited to 200mA. Controls the on the reader. Makes the go green when a valid card is presented, or flash red-green when access is denied. SIG Data from the reader. If using one reader this goes to Sig A, if using two readers the entry (usually) goes to Sig A, the exit to Sig B. /GND Ground or 0v return. This conductor may also be used for the Door Contact and circuit. TM One Touch Use the 'One Touch' test (See Page 22) to verify correct operation of the readers. Warning: The voltage supplied at the reader power terminals is the same as the controller input voltage (2 or 24V). You should ensure that the readers you are using can operate at this voltage. PROGRAMMING In the Doors section, select the door name. In the Access tab: Select the Reader Type. This should be PAC Proximity Reader Assign an Area to SIG A If using two readers, assign an Area to SIG B 4

14 LOCK CONTROL SUPS 2 24 OR VOLTS TCP/IP This device complies with Part 5 of the FCC Rules. Operation is subject to the following two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation Made in UK LOCK RELAY 30 V; 5A A + - PRE-WIRED FROM POWER SUPPLY VIN LOCK Manufacture Date POWER ACCESS AC 52 IP Mk. 2 Access Controller One-Touch Testing To enter View Mode press the One-Touch button momentarily. To enter Active Mode press and hold the One-Touch button for 2 to 4 seconds. To leave One-Touch testing, press the button momentarily again. Note that One-Touch Active mode will automatically time out after hour. For details of One-Touch modes see the enclosed Quick Start Guide. SIGNAL VOLTAGE 0.2 A MAX DOOR 2 LOCK 2 RELAY 2 30 V; 5A A + - IMANT! THE MOV (METAL-OXIDE VARISTOR) SUPPLIED WITH EACH SHOULD BE CONNECTED ACROSS THE LOCK TERMINALS. 2/24V 5V DATA 2 DOOR2 DETAILS A A fuse should be connected in line with the positive conductor to each lock. Locks are controlled by a relay. There is one relay, labeled 'LOCK ' or 'LOCK 2', for each door. The relay is able to switch up to 3A at 3. but ensure that the lock current does not exceed the limit of the power supply. Power for the locks can be taken from the Access terminals (LOCK and ) on the controller or from an independent power supply. Voltage at the LOCK terminal is the same as provided at the VIN terminal. Cable gauge should be sufficient to ensure the correct operating voltage is provided at the lock, typically 8AWG. Fail Secure locks (e.g. Strikes) should be switched through the Normally Open () relay terminal. Fail Safe locks (e.g. Magnetic Locks) should be switched through the Normally Closed () relay terminal. It is important to fit the MOV at the lock terminals. One is supplied with each reader. The MOV prevents back EMF (spikes) from damaging the relays or inducing transients in other cables. PROGRAMMING In the Doors section, select the door name. In the Configuration tab: Select Lock Release Time default is 5 seconds In the Details tab: Select a Door Profile if you want automatic opening default is None. AVAILABLE LOCK POWER PRODUCT POWER CONSUMPTION QTY 2V SUB-TOTAL PAC 52 DOOR CONTROLLER STANLEY GS3 MULLION TOTAL@2V 0.42A 3.0A A 2.58A less 20% Safety Factor * 0.52A REMENDED AVAILABLE FOR LOCKS 2A *It is considered best practice to run at less than the full capacity of the power supply. This allows for unforseen peak requirements and will increase lifespan. 5

15 INSTALLATION RS-485 Each Two-Door Starter Kit can be expanded with up to 23 additional Two Door Expansion Kits on a RS-485 multidrop, for a total of 48 Doors. CABLE SPECIFICATIONS Max cable distance CAT5 or CAT6 Up to 3000 ft 22AWG Unshielded Up to 500 ft When used with an RS485 data line, on-board termination resistors can be put in circuit with a simple termination jumper. Ensure that units installed in the middle of the data line have this switch turned OUT. The RS-485 bus must be configured as a straight line with no branches. Termination Jumper Termination: set to IN at each end of the bus set to OUT on devices in between OUT IN OUT IN OUT IN Cat 5 or Cat 6 cable can be used for a total length of up to 3000 feet. Use one twisted pair for the N and N0 signals; use another pair together for NGND. Double over each conductor to make a stronger connection. If shielded cable is used then connect the shield to the ( ) GROUND at one end of the cable only. Note. Only required in harsh environments - Speak to a technical support engineer if required. 6

16 DOOR INPUTS DOOR CONTACT (RMALLY CLOSED DOOR CONTACT) The door contact is usually a sensor in the door frame that detects the position of the door. CABLE SPECIFICATIONS Cable Requirement 22AWG, 2-conductor, stranded, unshielded Door Contact Controller wiring 2-24V D/SIG /GND D0/CLK TAM P SOUND O N CTS A M AX DOOR 2 DO Join wires RMALLY CLOSED The circuit is Normally Closed. When the door is closed the circuit is closed, when the door is open the circuit is open. If the controller knows the door position then it can respond in certain conditions. For example: If the door opens without a valid card or input then a Door Forced alarm is generated. If the door stays open beyond a certain time then a Door Left Open alarm is generated. If the door opens after a valid card or then the lock release time is cancelled after a further 2 seconds. This helps ensure that the door catches again when it closes. Use the 'One Touch' test (Page 22) to verify correct operation. PROGRAMMING In the Doors section, select the door name. In the Configuration tab: Check Door Monitoring default is unchecked Enter Door Open Time this is the time before a Door Left Open Alarm is generated. Typically 30 to 60 seconds (maximum is 255 seconds) 7

17 DOOR INPUTS REQUEST TO (EGRESS, OR REX) CABLE SPECIFICATIONS Cable Requirement 22AWG, 2-conductor, stranded, unshielded The Request to Exit ( or REX) device is located on the secure side of the door. When activated it indicates to the controller that the door is about to open. If the door is being monitored and the controller does not receive the signal, an alarm will be generated. Only one conductor is needed between to controller and the contact if the reader ground is used (as shown in diagram). Alternatively a dedicated pair of conductors can be used. Controller wiring 2-24V D/SIG /GND D0/CLK TAM P SOUND O N CTS A M AX DOOR 2 DO D SIGA SIGB Join wires RMALLY OPEN The circuit is Normally Open. The circuit just needs to close momentarily. It should not remain closed for more than 2 to 3 seconds or more than the lock release time. If the circuit remains closed for more than 5 cycles of the lock release time (25 seconds if the lock release time is 5 seconds) then an Held Down alarm is generated. Activating the device may or may not operate the lock as well this can be set in programming, see below. There are several devices that can be used to generate the signal. Examples include: Push to Exit button a momentary switch near the door that a person presses to release the lock. Crash-bar or Handle switch. A switch inside the crash-bar or lock handle that closes when either is operated. Often used for escape routes where the door has to open when pushed. Motion Rex. A motion detector above the door that detects presence and closes a switch. In most cases this will be set T to operate the lock. These devices can be difficult to set correctly. The detection field should be set so that only people approaching the door activate the switch. You should also ensure that the detector just closes the switch momentarily. Use the 'One Touch' test (see Page 22) to verify correct operation. PROGRAMMING In the Doors section, select the door name. In the Configuration tab: If you do T want the lock to operate when the is closed: Set Mode to No Lock default is Normal 8

18 DOOR OUTPUTS CONTROLLER OVERRIDE AND ER The Door Controller has two extra inputs. Both are normally closed (N/C). RMALLY CLOSED ER The Tamper is prewired to a tamper switch which registers a 'Case Tamper' alarm event when the lid is opened. Pre-Wired Tamper Switch OVERRIDE The Override has a factory installed jumper ensuring its circuit is closed. If you intend to use this input then remove the jumper and connect your own wiring. When this input opens both doors on the controller will unlock. A 'Controller Override' alarm event will be generated. When the input closes the doors will return to their normal operation. If you just want one door to release then use the auxiliary input on the individual door. (see Door Input -> Extra Door Input) RMALLY CLOSED Door Emergency Override 9

19 20 ON CTS DOOR INPUTS EXTRA DOOR INPUT (PER DOOR CHANNEL)* 2-24V D/SIG /GND D0/CLK 52 SOUND 0.2 A MAX DOOR 2 D SIGB RMALLY OPENED DETAILS - INPUT Each door has an extra input. This is normally closed (N/C) or normally open (N/O) depending on function: Reader Tamper N/C Can be used with readers that have a tamper detection circuit. Bolt Door N/O Bolts door no keys operate unless they have an access group with 'Ignore Bolted Doors' privilege. Emergency Override N/O Unlocks door when closed, door returns to normal when opened. Latch Contact N/C Generates a 'Door Lock Forced' alarm when opened EXTRA DOOR OUTPUT (PER DOOR CHANNEL)* DETAILS OUTPUT Each door also has an auxiliary output relay. This can be programmed to respond to a variety of events: Door left open Door Forced Door left open/door forced Alarm shunt Time Profile When door is left open beyond its programmed time When door is opened without a valid key being presented or Either door left open or door forced Opens for lock release time when valid key is presented or pressed Relay follows selected time profile Automatically sound an alarm after a set period of time when a door is propped open. Use the Extra Door Relay and program the system to sound the alarm if a door is held open for too long. PROGRAMMING In the Doors section, select the door name. In the Auxiliary I/O tab: Select Auxiliary Input Mode - default is None Select Auxiliary Output Mode - default is None 20

20 One-Touch Installation Testing The PAC 52-series controller has built-in diagnostics, enabled using the 'One Touch' button. The One Touch button is located next to green 'Status'. This indicates whether One Touch mode is active or not. When One Touch View Mode is enabled the set of small s next to each door channel will operate. If you activate Test Mode then the controller will stop operating and allow all the readers and inputs to be tested. One Touch can be used when the controller is first installed and powered up, and only rquires one person. It requires no programming and can be used to verify that all connections are correctly made and operating as expected. RMAL MODE The status led flashes slowly, about twice a second. The controller works normally as programmed. The indicator lights whenever the lock is released. VIEW MODE Press One Touch for -2 seconds The status led flashes faster, about three times a second. The controller works normally as programmed. The and lights are active. TEST MODE Press One Touch for 4 seconds The status led flashes rapidly, about five times a second. The controller stops working normally and goes into test mode. The and lights are active. DOOR S ( ) Use either mode to observe the door channel s. (See Step 2 on the One-Touch Test Card) If you see the indicator is permanently on, then it is quite possible the circuit is wired as normally closed. If you have a motion installed then you should see this flash on and off when somebody enters the detector field. The indicator will turn red when the door contact is open. TEST MODE The Starter Kit includes a One-Touch Test Card. STEP - TEST MODE INSTALLATION TESTING One Person Installation Testing at the Door. Press the door controller s One Touch button for 4 seconds to activate test mode for one hour. All the readers attached to this controller will latch from red to green. All feedback is provided by the reader. To exit hold 'One Touch' button for 4 seconds or it will time out after hour. Present this card to the Entry Reader. Reader will flash from green to red once and the lock will release. Present this card to the Exit Reader. Reader will flash from green to red twice and the lock will release. Operate the Request-to-Exit (/REX). Reader will flash from green to red three times. Open the Door Contact. Reader will flash from green to red four times. Default state STEP 2 Two Person Installation Testing. INSTALLATION TESTING - TEST MODE STEP INSTALLATION TESTING One Person Installation Testing at the Door. - TEST MODE Press the door controller s One Touch button for 4 seconds to activate test mode for one hour. All the readers attached to this controller will latch from red to green. All feedback is provided by the reader. To exit hold 'One Touch' button for 4 seconds or it will time out after hour. Present this card to the Entry Reader. Reader will flash from green to red once and the lock will release. Present this card to the Exit Reader. Reader will flash from green to red twice and the lock will release. Operate the Request-to-Exit (/REX). Reader will flash from green to red three times. Open the Door Contact. Reader will flash from green to red four times. In Test Mode, the Door Contact () and Request-to-Exit (/REX) lights are active. There are two sets, at the top and bottom of the controller next to Door and Door 2. If the /REX indicator is permanently lit, the /REX circuit may be wired as normally closed. When a motion /REX installed this will flash on and off when somebody enters the detector field. The indicator will turn red when the door contact is open. Default state ESS SIGNAL VOLTAGE 2/24V 5V DATA AY 2 ; 3 A 2 DOOR2 /REX DOOR2 2

21 PAGE INTENTIONALLY BLANK

22 SECURITY ON INSTALLATION ADDENDUM STANLEY GS3 CONNECTION (WIEGAND OUTPUT) When using third-party credentials such as HID with Stanley GS3 readers, it is normal to use the factory default PAC64 output mode and use a single data line (SIGA/D0) using unshielded cable. In some situations, such as a system takeover, you may have existing readers to maintain. In this situation, Stanley GS3 readers can be wired with a wiegand output that uses two data lines (labeled D0 and D) and use shielded cable at up to 500ft. You will need to set the Output Format switch on the GS3 readers to Wiegand (see illustration). The PAC 52 controller can only support one reader of this type per door channel. EXAMPLES OF THIRD PARTY WIEGAND CREDENTIALS PRODUCT SPECIFICATIONS (USING N-PAC CREDENTIALS) Power requirements Operating Voltage Range Max Current Requirements Max cable distance Cable Requirement Conductors Required 0.5 V to 28 V <00 Ma 500 ft HID 346 ProxKey III 22AWG, stranded, shielded HID386 ISOProx II Card 5 conductors (If REX and Door Contact not used) C US C US LISTED ON 2-24V D/SIG /GND D0/CLK SOUND Set the Output Format to Wiegand using the DIP Switches DATA LEVEL There is a jumper on the circuit board that may need to be set for certain types of reader. By default the jumper should be set to 2v/24V. If a reader is powered from a 5V supply, or the reader outputs a 5V signal level, e.g. Bioscrypt fingerprint readers, then set the jumper to 5V 5V 2/24V DATA 23

23 INSTALLATION ADDENDUM CONNECTION DETAILS (WIEGAND OUTPUT) Installation Notes:. The number of conductors will depend on whether you are using a door contact and request to exit device. 3. After installation in wet or damp locations, it is good practice to seal the green connector well with electronics grade RTV silicone sealant to ensure that moisture cannot enter or accumulate in wiring compartments. Signal Description Power. The voltage at this terminal is the same as the voltage used to power the controller. Power is limited to 200mA., VCA D0 Controls the on the reader. Makes the go green when a valid card is presented, or flash red-green when access is denied. Data from the reader. D GND Data from the reader. Ground or 0v return. This conductor may also be used for the Door Contact and circuit. Use the 'One Touch' test (See Page 22) to verify correct operation of the readers. Warning: The voltage supplied at the reader power terminals is the same as the controller input voltage (2 or 24V). You should ensure that the readers you are using can operate at this voltage. PROGRAMMING In the Doors section, select the door name. In the Access tab: Select the Reader Type. This should be Wiegand Assign an Area to SIG A/ SIG B 24

24 Technical Support