Introduction. Prerequisites. Ballbar - QC20-W - Analysis LAST UPDATED: 12/01/2018
|
|
- Christina Bradley
- 5 years ago
- Views:
Transcription
1 Ballbar - QC20-W - Analysis LAST UPDATED: 12/01/2018 Ballbar - QC20-W - Analysis Introduction This procedure tells you how to do a Renishaw QC20-W ballbar analysis. The QC20-W BallBar uses a Bluetooth connection to send the measured data to the computer Tool Holder Magnetic Center Cup (for the spindle) QC20-W Ballbar Transducer Magnetic Ball Assembly (for the table) QC20-W Bluetooth USB Dongle Prerequisites Let the ballbar calibration kit adjust to the ambient temperature for a minimum of 30 minutes. Install the Renishaw QC20-W Ballbar Software on your computer. Install the CR2 battery into the QC20-W Ballbar transducer Page 1 of 9 pages Zerodur Calibrator Magnetic Mount Assembly (for the table) QC20-W Ballbar Transducer CR2 Battery (for the Transducer) QC20-W Bluetooth USB Dongle Magnetic Center Cup (for the spindle) Setting Ball Extension Bars
2 Ballbar - QC20-W - Software - Configuration 1 On your computer, click the Start button. Select All Program and open the Renishaw Ballbar 20 program. Click Configuration and select Maintain Calibrators [1]. On the Maintain Calibrators window, click the Add a Calibrator tab [2]. On the Add Calibration window [3], enter all the certificate calibration information for the mm Ballbar. Note: The calibration certificate is inside the compartment of the QC20-W equipment case. Click Add. Click OK. 2 On the Maintain Calibrators window, click the Uniticon [1]. Select the correct measurement units in the dialog box. Click OK. Page 2 of 9 pages
3 Ballbar - QC20-W - Bluetooth - Setup 1 Put the QC20-W Bluetooth USB dongle into your computer. Let Windows automatically install the device driver software. If the Bluetooth communication fails, do these steps: Note: If one of these steps makes you wait a long time, remove and put back the QC20-W Bluetooth USB dongle into your computer and start again. Click the Bluetooth icon [1] and select Add a Device. Click Bluetooth Other [2]. Click Next. Click Pair without using a code [3]. Wait until Windows completes adding the device. Click Close. Page 3 of 9 pages
4 Ballbar - QC20-W - Analysis - Quick Check Mode Page 4 of 9 pages
5 1 Set the main circuit breaker to the ON position. Push [POWER ON]. Push [RESET] to stop each alarm. Push [ZERO RETURN]. Page 5 of 9 pages
6 2 On Graphic Mode, make sure the ballbar test programs are installed. If not, load the ballbar test programs into the control. Move the table to the center of the machine. Install the magnetic tool cup [1] with a tool holder into the spindle. Put the center mount assembly [3] with the setting ball [2] onto the center of the table. Loosen the center mount assembly and align it with the center of the magnetic tool cup [1]. Align the tool cup of the spindle with the center mount and the ball joint. Tighten the lock bar (4) of the center mount. Push [OFFSET] one or two times to select WORK ZERO OFFSET on the display. Select G54 and push [PART ZERO SET] for the X, Y and Z axes. Jog the Z axis up 2 (5 cm). Remove the setting ball. Push [CYCLE START] to do a test of the program. Page 6 of 9 pages
7 3 Make sure the CR2 battery is installed in the transducer. Turn the transducer cap clockwise to start it. The green LED on the transducer comes on. Put the transducer onto the calibrator. On your computer, click the Start button. Select All Programs and open the Renishaw Ballbar 20 program. Select Quick Check. Note: Enter the measurements in inches or metric. 1. Click the Run a ballbar test. 2. Set Machine Type to Z vertical (For a vertical mill). 3. Set Test Plane to XY. 4. Set Feedrate to in/min (254 mm/ min). 5. Check Calibrator. 6. Set Machine Expansion Coefficient to 6.6 F (11.9 C). 7. Set Test Radius, select Custom and type in ( mm) (Do not include the last 2 digits from ). 8. Click the right Arrow to continue. 4 Click the Green button [1] to view the simulated movement. Make sure this movement is the same as the movement pattern of the ballbar test program on the machine. Click the right Arrow [2] to continue. Type pre-test comments [3], if necessary. Click the right Arrow to continue. Page 7 of 9 pages
8 Ballbar - QC20-W - Analysis 5 On the Port:Bluetooth, click the down Arrow. Select QC20-W [1] to find the ballbar Bluetooth device. Click Search Again [2]. Note: If the ballbar Bluetooth device is not found, remove and put back the QC20-W Bluetooth USB dongle into your computer and start the search again. When the device is found, select the Ballbar Bluetooth Device [3] icon. Click Ok. The ballbar Bluetooth LED changes color from green to blue. 6 Put the QC20-W transducer onto the calibrator as shown in the illustration [1]. Click the calibration button [2]. When the message Calibrated [3] shows on the screen, click the right Arrow to continue [4]. 7 Push [CYCLE START] to start the ballbar test program to position X, Y, and Z axes on the initial start point. Clean the tip of the transducer with putty. When the program stops, attach the QC20-W ballbar to the magnetic cup [1] and the magnetic mount [2]. Click the green button [3] to collect the data. Push [CYCLE START] to complete the ballbar test program. Click the Floppy icon [4] when the test is completed. Type the name for the file [5]. Click Save. Page 8 of 9 pages
9 8 Click the Result icon [1] to show the percentages screen. For the machine to operate correctly, the Circularity value [2] must be less than " (0.013 mm). Do the QC20-W ballbar test program on each axis combination, XY, XZ, and YZ. At the start of the test program as shown in Steps 3 and 4, do the following for axes XZ and YZ: Set the correct axis [3]. Set the 220/2 icon [4]. Refer to the RENISHAW BALLBAR TEST - PLOT INTERPRETATION - MILLS document. Page 9 of 9 pages
Ballbar QC20-W - Analysis
Haas Technical Documentation Ballbar QC20-W - Analysis Applies to machines built from: January, 2016 Scan code to get the latest version of this document Translation Available Ballbar QC20-W - Analysis
More informationQC20-W wireless ballbar system description and specifications
QC20-W wireless ballbar system QC20-W wireless ballbar system description and specifications Hardware Software QC20-W ballbar and ballbar kit QC20-W ballbar The QC20-W ballbar contains a precision linear
More informationTMS Total Machine Service Corp.
Renishaw Ballbar Test Data Renishaw Ballbar testing in 2 planes gives a full analysis of 23 different machine errors. Below are some of the most common problems. Backlash or Lost Motion Play in the drive
More informationIEEM 215. Manufacturing Processes I Introduction to the ARIX CNC milling machine
IEEM 215. Manufacturing Processes I Introduction to the ARIX CNC milling machine The image below is our ARIX Milling machine. The machine is controlled by the controller. The control panel has several
More informationQC20-W wireless ballbar system description and specifications
QC20-W wireless ballbar system QC20-W wireless ballbar system description and specifications Hardware Software QC20-W ballbar and ballbar kit QC20-W ballbar The QC20-W ballbar contains a precision linear
More informationOur thanks go to: Puppy Linux, RTAI, EMC, axis, all the kernel developers and big mama thornton.
CoolCNC Linux First Steps This manual is a step by step introduction for the installation of the CoolCNC Linux Live CD. Its intent is to lead to a better understanding of the current processes. This document
More informationQuickly diagnose the performance of your machine tools
QC10 ballbar system Quickly diagnose the performance of your machine tools Reduces down-time Reduces both machine down-time and maintenance costs Compliance Reports comply with ISO, ASME and JIS standards
More informationLadybird Project - Vacuum Mould
- Vacuum Mould Prerequisite Mould drawn and saved as STL file from Solidworks Focus of the Lesson On completion of this exercise you will have completed: Opening STL file Setting Machining Constraints
More informationHDS Series Quick Start Guide.
Techno-Osai Start Up Sequence HDS Series Quick Turn the Main power switch to the ON Position. 220 volts should have been attached to this switch by an electrician. Power On Button. Computer power ON. The
More informationFAGOR AUTOMATION MC TRAINING MANUAL
FAGOR AUTOMATION MC TRAINING MANUAL ACER MC TRAINING MANUAL 8 holes 1/2" depth grid pattern R0.125 1.5 6 unit: inch R0.25 4 1.25 2 2.675 1/2" depth rectangular pocket 1/2" depth circular pocket R0.75 8
More informationCIRCULAR INTERPOLATION COMMANDS
PROGRAMMING JANUARY 2005 CIRCULAR INTERPOLATION COMMANDS G02 CW CIRCULAR INTERPOLATION MOTION & G03 CCW CIRCULAR INTERPOLATION MOTION *X Circular end point X-axis motion *Y Circular end point Y-axis motion
More informationRunning a Job on the Large Mill
Running a Job on the Large Mill Digital Media Tutorial Written by Trevor Williams Turning On the Machine Flip the breaker switch on the front right of the lower part of the controller box to the ON position.
More informationFlashCut CNC / Precix Router User s Guide v1.2 Brett Ian Balogh 31.October, Ensure the computer is plugged in. Do not plug the spindle in yet.
FlashCut CNC / Precix Router User s Guide v1.2 Brett Ian Balogh 31.October, 2011 1. Ensure the computer is plugged in. Do not plug the spindle in yet. 2. Start the computer by pressing the on/off button
More informationCOPYCAT NEW FANGLED SOLUTIONS 2/6/2009
1.0 INTRODUCTION 1.1 CopyCat is a unique wizard used with MACH3. It is not a stand alone program. This wizard will allow you to jog a machine around and create a Gcode file from the movement. 2.0 REQUIREMENTS
More informationSilver Merchandising. DI and Car Audio Security. Interactive Technology Support technology made easy
Silver Merchandising Interactive Technology Support technology made easy For security in the DI and GPS sections of the store, Best Buy primarily uses MTI s Freedom system to secure the devices. There
More informationComputer Numerical Control for Windows Version 1.2. User s Guide
Computer Numerical Control for Windows Version 1.2 User s Guide 1998 FlashCut CNC, Inc. 1263 El Camino Real, Suite W, Menlo Park, CA 94025 Phone (650) 853-1444 Fax (650) 853-1405 www.flashcutcnc.com Table
More informationVanderbilt Small Molecule NMR Center
Vanderbilt Small Molecule NMR Center Instructions for Using TOPSPIN version 2.0 DRX 400: Setting up 1H, 13C (1H decoupled), and 31P NMR Experiments Getting started: Sample Preparation: Make sure your sample
More informationCalibration and setup of a tool probe
Calibration and setup of a tool probe Fundamentals Tool-setting is the process of determining geometric information length, radius and / or diameter of a cutting tool using a tool-setting device. Some
More informationThe Cisco Wireless IP Phone 8821-EX has not been tested or certified with any accessories for use in Potentially Explosive Atmosphere.
Supported, page 1 Headsets, page 1 Cisco Wireless IP Phone 8821 Desktop Charger, page 2 Cisco Wireless IP Phone 8821 Multicharger, page 6 Secure the Charger with a Cable Lock, page 10 Supported You can
More informationIntroduction to the Work Coordinate System (WCS) April 2015
Introduction to the Work Coordinate System (WCS) April 2015 Mastercam X9 Introduction to WCS TERMS OF USE Date: April 2015 Copyright 2015 CNC Software, Inc. All rights reserved. Software: Mastercam X9
More informationLaser Doppler Displacement Meter Laser Measurement System
Laser Doppler Displacement Meter Laser Measurement System Title: Incoming inspection procedure Document identification: MCV 500 incoming OPTODYNE, INC. 1180 Mahalo Place Compton, CA 90220 310-635-7481
More information4-20 ma Current Data Logger
1 4-20 ma Current Data Logger OM-DL420 DATA LOGGER INSTRUCTIONS The OMEGA OM-DL420 Data Logger is a self-contained precision instrument for recording the current in a 4 20 ma loop. The OM-DL420 can store
More informationConversational Programming for 6000i CNC
Conversational Programming for 6000i CNC www.anilam.com P/N 634 755-22 - Contents Section 1 - Introduction Section 2 - Conversational Mode Programming Hot Keys Programming Hot Keys... 2-1 Editing Keys...
More information2000 Series Mill / Router Operating Manual
2000 Series Mill / Router Operating Manual 1. Introduction 1.1 Control Startup To open the control software double-click on the profile icon on the desktop. Control Icon 1.2 Overview This manual gives
More informationSOFTWARE POST-PROCESSING OF DATA STRUCTURE OBTAINED FROM MEASURING DEVICE BALLBAR QC20
SOFTWARE POST-PROCESSING OF DATA STRUCTURE OBTAINED FROM MEASURING DEVICE BALLBAR QC20 Kuric, I.; Košinár, M.; Tofil, A.; ivan.kuric@fstroj.uniza.sk matus.kosinar@fstroj.uniza.sk atofil@pwsz.chelm.pl Abstract:
More informationLesson 4 Introduction To Programming Words
Lesson 4 Introduction To Programming Words All CNC words include a letter address and a numerical value. The letter address identifies the word type. The numerical value (number) specifies the value of
More informationConversational Programming for 6000M, 5000M CNC
Conversational Programming for 6000M, 5000M CNC www.anilam.com P/N 70000486F - Contents Section 1 - Introduction Section 2 - Conversational Mode Programming Hot Keys Programming Hot Keys... 2-1 Editing
More informationG360 Panoramic Camera Gimbal
Instruction Manual EN V 1.0 G360 Panoramic Camera Gimbal Compatible with Samsung gear 360/Kodak pixpro sp360/kodak pixpro sp360 4k/Sony FDR-X3000 etc. GuiLin FeiYu Technology Incorporated Company Product
More informationINSTALLING THE WINDOWS-BASED DRIVER NOTICE!
INSTALLING THE WINDOWS-BASED DRIVER NOTICE! Keep the machine and the computer unconnected until you carry out this installation operation. Failure to follow the correct procedure may make installation
More informationMultiVision Operating Instructions
Innovation. Quality. Performance. Best in Industry. Worldwide. 1 MultiVision Operating Instructions MultiVision offers operators the option in completing various projects to use cameras for setting up
More informationChapter 19 Assembly Modeling with the TETRIX by Pitsco Building System Autodesk Inventor
Tools for Design Using AutoCAD and Autodesk Inventor 19-1 Chapter 19 Assembly Modeling with the TETRIX by Pitsco Building System Autodesk Inventor Create and Use Subassemblies in Assemblies Creating an
More informationDI-5C. Prisma INSTRUMENT USER MANUAL
DI-5C Prisma INSTRUMENT USER MANUAL INDEX 1. Instrument overview 2. How to use the instrument 2:1 Description 2:2 Display 2:3 On/Off & push buttons 2:4 Settings Set date / time Change number of digits
More information5 Axis Cutting Using Delcam Powermill Written by: John Eberhart DM Lab Tutorial
5 Axis Cutting Using Delcam Powermill Written by: John Eberhart DM Lab Tutorial This tutorial covers how to setup a job for a Multi-Axis Toolpath specifi cally using the Robot. Note: You need to follow
More information3D Surface Plots with Groups
Chapter 942 3D Surface Plots with Groups Introduction In PASS, it is easy to study power and sample size calculations for a range of possible parameter values. When at least 3 input parameters vary, you
More informationRadio Mini Wireless Wheel Mouse User s Guide MODEL: RFMSW-15
Radio Mini Wireless Wheel Mouse User s Guide MODEL: RFMSW-15 Trademark Recognition Windows, Office 97 and MS-IntelliMouse are registered trademarks of Microsoft Corp. RFMSW-15 THIS DEVICE COMPLIES WITH
More information3D SYSTEMS University CubeX 3D Printer
3D SYSTEMS University CubeX 3D Printer Lesson Leveling the Print Pad and Print Tips, Setting the Z-Gap Revision date: 10/22/13 1 1 2016 年 6 月 14 日 Objectives After completing this lesson you will: Be able
More informationG360 Panoramic Camera Gimbal
Instruction Manual EN G360 Panoramic Camera Gimbal Compatible with Samsung gear 360/Kodak pixpro sp360/kodak pixpro sp360 4k/Sony FDR-X3000 etc. GuiLin FeiYu Technology Incorporated Company V 1.0 Product
More informationPress the PEN HOME key to move the pen(s) to the outside of the chart. The pen(s) is automatically raised off the chart.
DICKSON GETTING STARTED 7-day chart rotation 0 to 100 o F KT8P0/2/3 & KT856 Remote Sensing Temperature Recorder QUICK START 1. Remove the protective pen cap(s). 2. Connect Probe(s): a. KT8P0/2/3: Make
More informationReport Logger Manual Quick Start: V
Report Logger Manual Quick Start: V7 031714 1) The USB connector is on the end of the case under the smooth cap without the Dickson logo. Grip the cap top and bottom and pull to remove the cap. Connect
More informationimach III P1A-S CNC Control Pendant
www.vistacnc.com - 1 - imach III P1A-S CNC Control Pendant www.vistacnc.com - 1 - imach III P1A-S Pendant Manual v. 3.3.1 www.vistacnc.com - 2 - PREFACE Any machine tool, including computer controlled
More informationTB048 (Rev1) - Laser Mapping Procedure (Software Versions Prior to 2.61)
TB048 (Rev1) - Laser Mapping Procedure (Software Versions Prior to 2.61) Overview This document describes how to use a laser for ball screw mapping with CNC7 version 7.17 to CNC10 version 2.61. It assumes
More informationMaincon Control Software (Mill VER18 and Lathe VER11) - Load
Maincon Control Software (Mill VER18 and Lathe VER11) - Load LAST UPDATED: 09/20/2018 Introduction This procedure tells you how to do these tasks on any CNC machine with a Maincon PCB: Install a new Maincon
More informationThree-Dimensional Coordinate Systems
Jim Lambers MAT 169 Fall Semester 2009-10 Lecture 17 Notes These notes correspond to Section 10.1 in the text. Three-Dimensional Coordinate Systems Over the course of the next several lectures, we will
More informationFARO Scanning Plugin
FARO Scanning Plugin for Geomagic Studio 6 service release 4, Geomagic Qualify 6 service release 2, and Geomagic Qualify 7 Document version B Copyright 2004, Raindrop Geomagic, Inc. The FARO scanner is
More informationINTRODUCTION CT87E FEATURES AND CONTROLS
INTRODUCTION The CT87E is a precision instrument used to monitor and record the presence or absence of voltage, light, or sound level such as what would be produced by an operating electric motor or compressor.
More informationJinying. factors to. proposed. Introduction. Error element. solutions. same time, Figure
International Conference on Applied Science and Engineering Innovation (ASEI 2015) Error element analysis and detection for BV755 CNC milling machine based on Ball-bar Jinying Chen 1, Xiaotie Niu 2, Lijuan
More information3300M CNC Control Training Guide
3300M CNC Control Training Guide Turning the Control ON After the control has been turned ON press F10 F10 to continue. Then press Select to select next page 1 Main Areas of the Display Programmed Position
More informationWireless Bore Gauge WBG. user and installation manual
Wireless Bore Gauge WBG user and installation manual Contents Section Number & Title Page Number 1.0 Introduction 3 2.0 Installing a Gauge Head 4 3.0 Mechanical Adjustments 5 4.0 Set Up and Installation
More informationReplacing the Battery HP t5730 and t5735 Thin Clients
Replacing the Battery HP t5730 and t5735 Thin Clients Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows
More informationOPERATING INSTRUCTIONS:
List OPERATING INSTRUCTIONS: Preparation For Installation, Product Identification Charging The Batteries ing And Adjusting The Lift Mounting Head s Brackets Mounting Clamps And Quick-Locking Arms Installation
More informationPUR 800 Operational manual
PUR 800 Operational manual 1 2 Introduction This manual gives a step by step procedure on how to set up and use the PUR800 with its PC application software. For any additional information on the functions
More informationOKUMA MACHINING CENTER OPERATORS GUIDE OSP P200M THiNC
OKUMA MACHINING CENTER OPERATORS GUIDE OSP P200M THiNC OSP P200 Mill Training Rev1 1 OKUMA MACHINING CENTER OPERATORS GUIDE Scope 4 Section 1 Guide to Controls on Operation Panels 5 Section 2 Manual Tool
More informationTurning your ideas into reality Novakon MPG Manual
Novakon MPG Manual The E-STOP switch button on your Novakon CNC Control Pendant only provides Emergency STOP signal to Mach3 CNC application. For further protection in CNC operation, other emergency protection
More informationXRADIA microxct Manual
XRADIA microxct Manual Multiscale CT Lab Table of Contents 1. Introduction and Basics 1.1 Instrument Parts 1.2 Powering up the system 1.3 Preparing your sample 2. TXM Controller 2.1 Starting up 2.2 Finding
More informationStarting the KVM Console
Starting the KVM Console This chapter includes the following sections: KVM Console, page 1 Starting the KVM Console from a Server, page 5 Starting the KVM Console from a Service Profiles, page 5 Starting
More informationFirst Edition Termologger USB & OSAKA MicroLab Lite User guide
First Edition Termologger USB & OSAKA MicroLab Lite User guide First Print February 2007 Introduction The Termologger USB is a compact 16-bit USB data logger designed for accurate temperature monitoring
More informationOperators Guide. Vision 3 Pan & Tilt Head. Vinten Camera Control Solutions
Operators Guide Vision 3 Pan & Tilt Head Vinten Camera Control Solutions Vision 3 Pan and Tilt Head Publication Part No. 3543-8 Issue 4 Copyright Vinten Broadcast Limited 2004 All rights reserved throughout
More informationSSII SUV MANUAL. LAGUNA TOOLS 2072 Alton Parkway Irvine, California Ph:
SSII SUV MANUAL LAGUNA TOOLS 2072 Alton Parkway Irvine, California 92606 Ph: 800.234.1976 www.lagunatools.com 2018, Laguna Tools, Inc. LAGUNA and the LAGUNA Logo are the registered trademarks of Laguna
More informationQC20-W COM port profile for Windows 8
QC20-W COM port profile for Windows 8 Overview The purpose of this application note is to configure Ballbar 20 software to connect to QC20-W via a Bluetooth device set up as a COM port. This process should
More informationHumidity + Temperature + Pressure Datalogger
User's Guide Humidity + Temperature + Pressure Datalogger Model RHT50 Introduction Congratulations on your purchase of the Relative Humidity / Temperature / Pressure Datalogger. This datalogger can measure
More informationCHASSIS INSTALLATION GUIDE
SUPER SC942S-600 SC942i-600/550 SC942 CHASSIS INSTALLATION GUIDE 1.0 SUPER SC942 Chassis User's Guide Table of Contents Chapter I: Unpacking and Check Lists... 1-3 Chapter 2: Installation Procedures...
More informationMicroLite & MicroLab Lite User Guide. First Edition First Print February 2007 Fourier Systems Ltd.
MicroLite & MicroLab Lite User Guide First Edition First Print February 2007 Fourier Systems Ltd. Contents Introduction... 1 Chapter 1 Using the MicroLite... 2 1.1. Overview... 3 1.2. Getting Started...
More informationSet: User manual. Smartphone Application SLT-caliper. Codimex E1 - Electronic caliper
Set: Codimex E1 - Electronic caliper Smartphone Application SLT-caliper User manual Contents page 1. Introduction... 3 2. Electronic caliper Codimex E1... 4 2.1 Technical specifications... 4 2.2 Meaning
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationMarCator. Dial and Digital Indicators
MarCator. Digital and Dial Indicators MarCator. Dial and Digital Indicators Digital Indicators Overview 5-2 MarCator 175 R Standard versions with digital display 5-4 MarCator 186 R / 186 WR With tolerance
More informationLumaRail Free Stand Bed Assist Rail with IntelliBrite LED Night Light
LumaRail Free Stand Bed Assist Rail with IntelliBrite LED Night Light Assembly and Operation Instructions Thank you for investing in this premium Platinum Health product. Please carefully follow the assembly
More informationCOMPUTER NUMERICAL CONTROL OF MACHINE TOOLS
COMPUTER NUMERICAL CONTROL OF MACHINE TOOLS Department of Mechanical Engineering and Aeronautics University of Patras, Greece Dr. Dimitris Mourtzis Associate professor Patras, 2017 1/52 Chapter 8: Two
More information6 Series Mill Controller Operation Manual
6 Series Mill Controller Operation Manual Date: 2013/10/25 Version: 1.1 Contents 1 Function Key and System Configuration... 4 1.1 Main Screen Sections... 4 1.2 CNC System Configuration... 5 1.3 Coordinate...
More information3-Axis G-Force Datalogger
User Manual 3-Axis G-Force Datalogger Model VB300 Introduction Congratulations on your purchase of the VB300 G-Force Datalogger. The Model VB300 can measure and record shock and vibration (acceleration)
More informationUsing the Android teach-pad
with ROBWIN 7 and ROBOFORTH II v15/16 Components The components of the system are: 7 inch hand-held tablet Android software (apk or app ) already loaded. Bluetooth adaptor Serial port on rear of controller
More informationIRF90 - Rotating Focuser
IRF90 - Rotating Focuser Part # 600180 REV092111 Page 1 Contents Introduction and Overview... 3 Limitations... 3 Packing List... 4 Installation... 5 Remove Existing Focuser... 5 Installing the Rotating
More information3-Axis Stabilized Handheld Gimbal
3-Axis Stabilized Handheld Gimbal Guilin Feiyu Technology Incorporated Company User Manual EN V1.3 1. Product Overview * The showing sports camera is not included in the package Accessories Thumb Screw
More informationLesson 6 The Key Operation Procedures
Lesson 6 The Key Operation Procedures Step-by-step procedures can keep you from having to memorize every function that you must perform on your CNC machining center. You will soon memorize procedures for
More informationXL-80 spares list. Application note. Overview
XL-80 spares list Overview This application note lists the system components for the XL-80 laser system. To order please contact your local Renishaw office at www.renishaw.com/contact Description XL-80
More informationFUTEK USB Software Version User s Manual
FUTEK USB Software Version 2.0.0.0 User s Manual 10 Thomas, Irvine, CA 92618, USA Toll Free: (800) 23-FUTEK Telephone: (949) 465-0900 Fax: (949) 465-0905 futek@futek.com www.futek.com 2 Table of Contents
More informationVANTAGE CL1. Installation and use of the CL1 Karting Data Kit
Installation and use of the CL1 Karting Data Kit Table of Contents What s in the box 3 Items needed for installation 4 CL1 registration 5 D3 app install 6 Battery installation 7 Mounting the CL1 data box
More informationDiamond Scribing on MDX-40 & JWX-10
Diamond Scribing on MDX-40 & JWX-0 This document covers diamond scribing using the MDX- 40 and JWX-0 as well as the required accessories. Materials Required: BT-EGX-5, High Precision Spring Loaded Burnishing
More informationConversational Programming for 6000i CNC
Conversational Programming for 6000i CNC January 2008 Ve 01 634755-21 1/2008 VPS Printed in USA Subject to change without notice www.anilam.com P/N 634755-21 - Warranty Warranty ANILAM warrants its products
More informationSoftware designed to work seamlessly with your CNC Masters machine. Made to work with Windows PC. Works with standard USB
Software designed to work seamlessly with your CNC Masters machine Made to work with Windows PC Works with standard USB Clutter free interface. The software is engineered for the machine so you don t have
More informationF Ballbar Trace user guide
Ballbar Trace user guide Contents Ballbar help... 3 Safety Information... 3 Disclaimer... 3 Copyright... 3 Trademarks... 3 Introduction... 4 Visual contents... 5 Operating information... 6 Settings...
More information6 Series Mill Controller Operation Manual
6 Series Mill Controller Operation Manual Date: 2015/11/13 Version: 1.3 2 Contents 1 Function Key and System Configuration... 4 1.1 Main Screen Sections... 4 1.2 CNC System Configuration... 5 1.3 Coordinate...
More informationDigital Indicators 1075 / 1080 / Features. Technical Data IP MarCator. Digital Indicators
- 5-38 Digital Indicators 175 / 18 / 181 IP51 Features Functions: ON/OFF (Set display to zero) mm/inch Reversal of counting direction PRESET (for entering a numerical value) DATA (data transmission with
More informationSP ProLine 30. Straightness Professional Package with IT. Another fine solution by PC /13
Straightness Professional Package with IT PC 1020 11/13 Another fine solution by Content of Straightness Professional Package with IT T330 Self Levelling Sweep Laser (BG 830203) The T330 levelling laser
More information3 Indexer Installation For PRSalpha Tools
888-680-4466 ShopBotTools.com 3 Indexer Installation For PRSalpha Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents General Safety and Precautions...5
More informationDeltaPix M12Z Installation Guide
1 2 Minimum System Requirements Windows 7 / 8 Microsoft. Both 32 and 64 bit versions of Windows will work. Microsoft dotnet (normally already installed with Windows) 1.3 GHz Pentium III or higher (compatible)
More informationTECHNICAL SPECIFICATIONS...
1 Contents 2 INTRODUCTION... 2 2.1 Installation... 2 2.2 Power Supply... 2 2.3 Installation warnings... 2 3 TECHNICAL SPECIFICATIONS... 3 3.1 Scope of delivery... 3 3.2 Mechanical specifictions... 3 3.3
More informationUSER MANUAL INCLUDED IN THE BOX
USER MANUAL INCLUDED IN THE BOX Steering Motor Motor Cables Electronic Control Box Emergency Stop Button 3m USB cable Power Cord (UK, EU or US plug end) Additional Extras GT Steering Wheel - 6 x M5x16
More informationEquipment Support Structures
Equipment Support Structures Overview Conventions What's New? Getting Started Setting Up Your Session Creating a Simple Structural Frame Creating Non-uniform Columns Creating Plates with Openings Bracing
More information3-Axis Wearable Gimbal for Action Camera. Instructions. Guilin Feiyu Technology Incorporated Company
-Axis Wearable Gimbal for Action Camera Instructions Guilin Feiyu Technology Incorporated Company User Manual E N V. Catalogue. WGX Overview. Quick Start Guide. Function operation 4 Working Mode 4 Function
More informationHOBO External Temp/RH Data Logger (UX ) Manual
HOBO External Temp/RH Data Logger (UX100-023) Manual The HOBO External Temp/RH data logger records temperature and relative humidity in an indoor environment with its external sensor. Using HOBOware, you
More informationStandard Operating Procedure of Triboindenter (Hysitron TI 950)
Standard Operating Procedure of Triboindenter (Hysitron TI 950) I Sample Loading and Preparation DO NOT TOUCH the bottom of transducer and optical microscope. Always place the tall samples on the most
More informationOM-DLTT DATA LOGGER INSTRUCTIONS
OM-DLTT DATA LOGGER INSTRUCTIONS The OM-DLTT Data Logger is a self-contained precision instrument for recording the temperature of two independent temperature probes. Each temperature sensor is enclosed
More informationConversational Programming for 6000M, 5000M CNC
Conversational Programming for 6000M, 5000M CNC www.anilam.com P/N 70000486E - Warranty Warranty ANILAM warrants its products to be free from defects in material and workmanship for one (1) year from date
More informationZ Series and S4M Ribbon Take-Up Spindle Maintenance Kit
Z Series and SM Installation Instructions This kit includes the parts and documentation necessary to install the Ribbon Take-Up Spindle Maintenance Kit into the following printers: Z Series (ZM, Z6M, ZMplus,
More informationEquipment Support Structures
Page 1 Equipment Support Structures Preface Using This Guide Where to Find More Information Conventions What's New? Getting Started Setting Up Your Session Creating a Simple Structural Frame Creating Non-uniform
More informationCAM-KIT6. User Manual. Connects2Vision. Mirror with DVR & Rear Camera PRODUCT FEATURES:
User Manual CAM-KIT6 Mirror with DVR & Rear Camera PRODUCT FEATURES: Display: 5 inch Speaker: Built in MIC: Built in Mini USB: 5V 2A Micro SD Card Support: 32G max (not supplied) Rear Camera Input: 2.5mm
More informationGE FANUC 21 CONCEPT 55 MILL ATC TEACHER GUIDE
GE FANUC 21 CONCEPT 55 MILL ATC TEACHER GUIDE 11/1/07 Version 2 Made by EMCO Authored by Chad Hawk Training Index Control Keyboard Pg 1 Fanuc 21 Control Machine Control Fanuc 21 Screen. Pg 2 Fanuc 21 Keys.
More informationWelcome to. the workshop on the CNC 8055 MC
Welcome to the workshop on the CNC 8055 MC Sales Dpt-Training: 2009-sept-25 FAGOR CNC 8055MC seminar 1 Sales Dpt-Training: 2009-sept-25 FAGOR CNC 8055MC seminar 2 This manual is part of the course for
More informationUser's Guide. Video Borescope. Models BR200 and BR250
User's Guide Video Borescope Models BR200 and BR250 Introduction Congratulations on your purchase of this Extech BR200 (17mm camera head) or BR250 (9mm camera head) Video Borescope. This instrument was
More informationAnimations in Creo 3.0
Animations in Creo 3.0 ME170 Part I. Introduction & Outline Animations provide useful demonstrations and analyses of a mechanism's motion. This document will present two ways to create a motion animation
More information