INSTALLING THE WINDOWS-BASED DRIVER NOTICE!

Transcription

1 INSTALLING THE WINDOWS-BASED DRIVER NOTICE! Keep the machine and the computer unconnected until you carry out this installation operation. Failure to follow the correct procedure may make installation impossible. Automatic primary procedure 1 - Connect the type A USB cable to the computer (make sure the pc is turned on and connected to internet) 2 - Connect the other extremity of the type B USB cable to the Evo-One cnc mill you can find on the back of the machine. 3 - Wait until the Arduino drivers are automatically installed. Secondary procedure manual 1 - If the drivers do not install automatically connecting the Evo-One through the USB por, start from point Enter on our website Go to the products/download area 3 - Click on Driver Win for Evo-One and download the file ( 4 - Estract the downloaded file (with.rar extension) with the free software Winzip. 5 - From Windows Device Manager install the downloaded drivers. * * The passages to manually install the Evo-One drivers (for Windows) are shown below: 1- IF YOU CONNECT THE MACHINE TO THE PC AND THE DRIVERS DO NOT AUTOMATICALLY INSTALL. 3- A WINDOW WILL OPEN: SELECT THE SECOND TAB (DRIVER) AND THEN UPDATE DRIVER. 2- GO TO CONTROL PANEL > DEVICE MANAGER. CLICK ON Evo-One CNC Mill. 4- CLICK ON Browse my computer for driver software. 20

2 5- SEARCH THE FOLDER IN WHICH THE FILE HAS BEEN PRECEDENTLY DOWNLOADED FROM OUR WEBSITE. SELECT THE FOLDER CDM v WHQL Certified AND THEN CLICK ON OK. 6- A WINDOW WILL WARN YOU OF THE CORRECT INSTALLATION OF THE DRIVERS. 7- THE DEVICE CORRECTLY INSTALLED WILL MOVE FROM THE Other devices SECTION TO Controller USB. 21

3 CHAPTER 3.1 WARNINGS BEFORE YOU OPEN THE PANEL ATTENTION READ BEFORE YOU OPEN 1-WHEN YOU WANT TO CLOSE THE COVER KEEP IT STEADILY WITH YOUR HAND FROM THE HANDLE AND CARRY IT CAREFULLY UNTIL IT LEANS INSIDE THE METAL SHEET 2-THE SMALL PLASTIC JOINT OF THE PLEXIGLAS COVER MUST BE INSERTED IN THE ALUMINIUM SLOT ON THE FLAT SURFACE OF THE ALUMINIUM SHEET - THE PLEXIGLAS COVER COULD BREAK OR CRACK DUE TO A LACK OF ATTENTION FROM THE USER. ALWAYS CARRY THE COVER WHEN YOU OPEN OR CLOSE IT - - POSSIBLE RESIDUAL DUST OR SCRAPS ARE DUE TO THE FACT THAT WE PERSONALLY TEST EVERY SINGLE MACHINE - 23

4 CHAPTER 3.2 TYPES OF EMERGENCY STOPS TO ENSURE SAFETY HOW TO PERFORM AN EMERGENCY STOP. Press the Emergency Stop button. Operation stops immediately. TO CANCEL AN EMERGENCY STOP Turn the button in the direction of the arrows. EMERGENCY STOP DUE TO OPENING OR CLOSING THE FRONT COVER To ensure safety, opening a front cover during cutting or spindle rotation causes an emergency stop to occur. Operation cannot be resumed by closing the front cover. In order to resume the operation, restart the machine following. NOTE: REMIND TO DISENGAGE THE BUTTON IN THE LAUNCH AND NORMAL USE PHASES, BECAUSE IT WOULD CAUSE THE ARREST AND INCORRECT FUNCTIONING OF EVO-ONE AND THE CRE-MOV SOFTWARE. 24

5 EVO-ONE CONNECTION AND FIRST USE WARNINGS: - TO MOVE ONE THE XYZ AXES BEFORE MAKING THE HOME OF THE MACHINE MAY DAMAGE OR CAUSE THE DISCHARGE OF THE GUIDES ON THE AXIS Z. MAKERDREAMS WILL NOT RESPOND ANYHOW TO THIS KIND OF DAMAGES MADE BY THE USER. -IN CASE OF ERROR MAKE SURE THAT THE EMERGENCY STOP BUTTON IS NOT BEING USED. -WHEN USING THE TOUCH PLATE (AUTO ZERO) VERIFY THAT THE SIDE OF THE SMALL ALUMINIUM SQUARE-SHAPED PIECE HAS THE TRANSAPRENT STICKER PAPER POINTED DOWNWARDS, LEANED ON THE SURFACE. AN INVERTED DIRECTION MAY DAMAGE THE EXTREMITY OF THE SPINDLE. 1- TURN THE COMPUTER ON 2- CONNECT THE POWER SUPPLY CABLE TO THE MACHINE 3- CONNECT THE EMERGENCY STOP BUTTON AND THE TOUCH PLATE SENSOR FOR THE AUTO-RESETTING. 4- CONECT THE TOUCH PLATE SENSOR FOR THE AUTORESETTING 5-CONNECT THE B TYPE USB CABLE TO THE MACHINE 6- CONNECT THE OTHER A TYPE USB EXTREMITY TO THE COMPUTER 7- THE EVO-ONE DRIVERS WILL BE AUTOMATICALLY INSTALLED. IF NOT, CONSULT THE SOFTWARE SECTION ON OUR WEBSITE. 8- TURN THE MACHINE ON PUSHING THE BUTTON YOU FIND ON THE BACK OF THE MACHINE. 25

6 9- OPEN THE CRE-MOVE SOFTWARE YOU CAN DOWNLOAD FROM OUR WEBSITE MAKERDREAMS.IT IN THE SOFTWARE SECTION 10- CLICK ON THE CONNECT BUTTON IN THE FIRST WINDOW OF CRE-MOV. 11- AT EVERY LAUNCH, BEFORE ANY OPERATION, PUSH THE HOME BUTTON TO GO TO THE REFERENCE POINT OF THE MACHINE AND SET THE STARTING POINT OF ITS MOVEMENTS IN THE X-Y-Z AXES. *read note 12- UNSCREW THE ER11 ON THE POINT OF THE SPINDLE COUNTER- CLOCKWISE 13- CHOOSE THE APPROPRIATE COLLET FOR THE MILL YOU ARE GOING TO ASSEMBLE AND PUT IT INSIDE THE ER11 NUT. 14- SCREW THE NUT A LITTLE BIT WITH THE COLLET APPLIED IN THE ORIGINAL LOCATION. 15- INSERT INSIDE THE COLLET THE CHOSEN CUTTER FOR THE PROCESSING 16- COMPLETELY SCREW THE NUT WITH THE 12mm WRENCH AND THE ER11M *NOTE: MAKE SURE YOU ARE WORKING IN mm OR inches, INSERT A VALUE EQUAL TO THE MOVEMENT YOU WANT TO ACHIEVE AND MOVE THE MACHINE ON THE AXES TO GET TO THE ZERO OF THE STOCK YOU WANT TO MILL. 26

7 17- DETAIL OF THE NUT S CLOSURE. 18- POSITION AND FASTEN IN THE MIDDLE OF THE WORKING AREA THE STOCK YOU WANT TO MILL.. IN THIS CASE THE CALMP TOOL HAS BEEN USED. 19- MOVE THE SPINDLE ON THE AXES X AND Y IN THE MIDDLE OF THE STOCK WITH THE USE OF THE JOG ON THE SOFTWARE. ONCE POSITIONED PUSH RESET ALL ZERO. 20- POSITION THE TOUCH PLATE OVER THE STOCK TOWARDS THE DESTINATION OF THE EXTREMITY. 21- CLICKN ON THE AUTO Z BUTTON FROM THE CRE-MOV SOFTWARE THE Z AXIS WILL GO UP TO THEN GO DOWN TO REACH THE TOUCH PLATE WITH ITS EXTREMITY AND DISENGAGE. NOW YOU CAN REMOVE THE ALUMINIUM SQUARE-SHAPED PIECE. CLOSE THE FRONT COVERING. 23- IN ORDER TO LOAD THE GCODE FROM YOUR COMPUTER, CLICK ON OPEN AND SELECT THE FILE, THEN CLICK ON THE OPEN BUTTON OF THE OPENED WINDOW. 24- CLICK ON START TO LAUNCH THE MILLING PROCESS. AT THE END OF THE PROCESSING CLICK ON HOME AGAIN IN ORDER TO GO BACK TO THE ZERO OF THE MACHINE. 27