IQByy with VESA Dock and Power Adapter Cradle

Transcription

1 IQByy with VESA Dock and Power Adapter Cradle Installation Manual 1 Rev: A00

2 Parts Identification Monitor Side VESA Dock 2. IQByy thin client with VESA Dock and Power adapter. 3. Stand Side VESA Dock 4. Wall Inserts (4 Nos.) Optional 5. M4x35 Wood Screws - Wall (4 Nos.) Optional 6. M4x10 Screws-Monitor (4 Nos.) 7. HDMI to DVI (extra cost option) 8. Power Cord (Optional/Country Specific) 9. Cable Ties

3 Assembly 1. Unpack the poly cover from the Power Cable. 2. Route and anchor the Power Adapter Cable as shown below

4 Disassembly 1. Unscrew the captive screw holding the Stand Side VESA dock. 2. Slide and remove the Stand Side VESA dock. 3. Reverse the thin client to remove the Monitor Side VESA dock. 4

5 1. Unscrew the captive screw holding the Monitor Side VESA dock. 2. Slide and remove the Monitor Side VESA dock. Note: Do not remove the Monitor Side VESA dock if you do not intend to mount the client on a wall stand. Refer to the next slide for more information. 5

6 Methods of Mounting Method 1: Hanging on Wall / Fixing on the Wall Method 2: Mounting on a Wall Stand 6

7 Method 1: Hanging on the Wall / Fixing on the Wall 1. Drill 4 holes as per the center to center dimensions and details given below. 100mm 100mm 100mm Hanging on the wall Fixing on the Wall Hole Diameter: 5 mm. Hole Depth: 35 mm. Insert wall Inserts into drilled holes. 7

8 2. Fix the M4 screws to the wall as shown in the following image. Wall M4x35 Screw Wall Insert 2 to 3mm 8

9 Hanging on the Wall IQByy with VESA Dock and Power Adapter Cradle Using M4x35 wood screws, hang the Stand Side VESA dock on the wall as shown in the following figure. Note: Hanging on Wall for Monitor / TV - Recommended weight less than 10kg. 9

10 Fixing on the Wall IQByy with VESA Dock and Power Adapter Cradle Using M4x35 wood screws, hang the Stand Side VESA dock on the wall as shown in the following figure. 10

11 Correct Wall Side Dock Orientation Incorrect Wall Side Dock Orientation 11

12 1. Slide and fix the client to the Stand Side VESA dock as shown in the following figure. 2. Tighten the captive screw to fit the client in place. 12

13 3. Connect the necessary cables. 13

14 Method 2: Mounting on a Wall Stand Preparing the Monitor 1. Using M4 screw, fix the Monitor Side VESA dock behind the monitor. 14

15 Correct MonitorSide Dock Orientation Incorrect Monitor Side Dock Orientation 15

16 Preparing the Wall Stand 2. Fix the Stand Side VESA Dock using the M4 screws as show in the following image. Note: Ensure that the Sliding guide is at the top. 16

17 Correct Stand Side Dock Orientation IQByy with VESA Dock and Power Adapter Cradle Incorrect Stand Side Dock Orientation 17

18 1. Slide and fix the client to the Stand Side VESA dock as shown in the following figure. 2. Tighten the captive screw to fit the client in place. 18

19 3. Slide the Monitor assembly into the VESA Dock on the Thin Client and fasten using the Captive Screw. 19

20 4. Connect the necessary cables. View after installation. 20

21 IMPORTANT Installation in any orientation other than recommended will VOID warranty. Improper installation will cause the internal temperature of the unit to increase by 20 0 C C. This will lead to extremely high product failure rates and working life may be reduced by as much as 50-75%. 21

22 Best Practices 1. Do not expose the Itona to acidic environments. 2. Avoid installation in areas where oil can splash onto the Itona. 3. Avoid installing the Itona above any heat source (e.g. Fryer, Toaster, or HLZ). 4. The Itona must be installed in recommended orientation as shown in earlier slides. Tilt can be up to maximum of 30ºC to vertical. 5. Ambient air temperature around the Itona should not exceed 40ºC. 6. Relative Humidity of air around the Itona should not exceed 80% non-condensing. 7. Adequate ventilation must be provided for convection heat transfer to be effective. ALWAYS keep at least 4 clear space at the top, bottom, and rear of the Itona. 8. Avoid running cables to and from the Itona and above or near heat sources as the heat can be transmitted to the terminal through the cables. 9. Ensure proper Common Earth Grounding of the Itona and all devices attached to it. 10. Ensure sufficient Power Surge Protection is used for the Itona and all devices attached to it. 22 Thank You