Itona Md75 with VESA Dock and Power Adapter Cradle. Installation Manual

Transcription

1 Installation Manual Itona Md75 with VESA Dock and Power Adapter Cradle 1

2 Revision History Rev no. Change Details Created by Date B00 Included new chapters to set up the client Krishna Raju N.R 30 th May 14 A03 Included monitor connection methods. Gokul Anand 26 th May 14 A02 Included product front view. Krishna Raju N.R 7 th April 14 A01 Included replacing power adapter. Krishna Raju N.R 21 st February 14 A00 Creation Krishna Raju N.R 1 st December 13 2

3 Unpack the Product 1. Product Packaging Carton 2. Accessory Box 1. Cut open the top side of the carton Remove the accessory box from the carton. 2 Dispose off Silica gel sachet. 3

4 Identify the Parts in the Package Monitor Side VESA Dock 2. Md75 thin client with VESA dock and power adapter. 3. Stand Side VESA Dock 4. Wall Inserts (4 Nos.) 5. M4x35 Wood Screws-Wall (4 Nos.) 6. M4x10 Screws-Monitor (4 nos.) 7. Splitter Cable 8. Power Cord (Optional/Country Specific) 9. Cable Ties

5 Disassembly 1. Unscrew the captive screw holding the Stand Side VESA dock. 2. Slide and remove the Stand Side VESA dock. 3. Reverse the thin client to remove the Monitor Side VESA dock. 5

6 1. Unscrew the captive screw holding the Monitor Side VESA dock. 2. Slide and remove the Monitor Side VESA dock. Note: Do not remove the Monitor Side VESA dock if you do not intend to mount the client on a wall stand. Refer to the next slide for more information. 6

7 Methods of Mounting Method 1: Hanging on Wall / Fixing on the Wall Method 2: Mounting on a Wall Stand 7

8 Hanging on the Wall/Fixing on the Wall Drill 4 holes as per center to center dimensions and details given below. 100mm 100mm 100mm Hanging on the wall Fixing on the Wall Hole Diameter: 5 mm. Hole Depth: 35 mm. Insert wall Inserts into drilled holes. 8

9 Fix the M4 screws to the wall as shown in the following image. Wall M4x35 Screw Wall Insert 2 to 3mm 9

10 Method 1 Hanging on the Wall Using M4x35 wood screws, hang the Stand Side VESA dock on the wall as shown in the following figure. 10

11 Fixing on the Wall Using M4x35 wood screws, hang the Stand Side VESA dock on the wall as shown in the following figure. 11

12 Correct Wall Side Dock Orientation Incorrect Wall Side Dock Orientation 12

13 1. Slide and fix the client to the Stand Side VESA dock as shown in the following figure. 2. Tighten the captive screw to fit the client in place.. 13

14 Connect the necessary cables. DVI-I to VGA +DVI Splitter Cable 14

15 Method 2: Mounting on a Wall Stand Preparing the Monitor Using M4 screw, fix the Monitor Side VESA dock behind the monitor. 15

16 Correct MonitorSide Dock Orientation Incorrect Monitor Side Dock Orientation 16

17 Fix the Stand Side VESA Dock using the M4 screws as show in the following image. Note: Ensure that the Sliding guide is at the top. Preparing the Wall Stand 17

18 Correct Stand Side Dock Orientation Itona Md75 with VESA Dock and Power Adapter Cradle Incorrect Stand Side Dock Orientation 18

19 1. Slide and fix the client to the Stand Side VESA dock as shown in the following figure. 2. Tighten the captive screw to fit the client in place.. 19

20 Slide the Monitor assembly into the VESA Dock on the Thin Client and fasten using the Captive Screw. 20

21 Connect the necessary cables. Side view after installation. 21

22 Instructions to Connect Dual Monitor To connect two analog (VGA) monitors DVI-I to VGA + DVI "Splitter cable" (Supplied along with Md75) 22

23 To connect one analog (VGA) monitor and one digital (DVI) monitor DVI-I to VGA + DVI "Splitter cable" (Supplied along with Md75) 23

24 Do not connect this way. 24

25 Instructions to Connect Single Monitor To connect one analog (VGA) monitor (option 1) 25

26 To connect one analog (VGA) monitor (option 2) DVI-I to VGA + DVI "Splitter cable" (Supplied along with Md75) 26

27 To connect one digital (DVI) monitor 27

28 Replacing the Power Adapter 1. Unplug the power cord and power adapter cable. 2. Unscrew the power adapter cradle thumb screw. 3. Remove the power adapter from the cradle. 4. Place the new power adapter into the cradle with proper cable routing using cable tie as shown below Connect the power adapter cable and the power cord. 1 28

29 Thank You 29