KRONOS INSTALLATION INSTRUCTIONS
|
|
- Clare Hunter
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS
2 TABLE OF CONTENTS ENCLOSURE AND DONGLE ASSEMBLY 1 LIGHTED ENCLOSURES SLIM ENCLOSURE WIRED-ETHERNET DONGLE REAR-OFFSET MOUNT SIDE-MOUNT SURFACE MOUNT GLASS MOUNT 49-51
3 ENCLOSURE AND DONGLE ASSEMBLY LIGHTED ENCLOSURES The instructions below highlight our recommended installation method when installing Kronos Lighted Enclosures. INSTALLATION STEPS Step 1: Separate the back and front enclosures. 1 ENCLOSURE AND DONGLE ASSEMBLY LIGHTED ENCLOSURES 3
4 Step 2: Fasten the selected bracket (15 or 0 degree tilt) onto the back enclosure. The 15 degrees tilt bracket is shown here for reference. ENCLOSURE AND DONGLE ASSEMBLY LIGHTED ENCLOSURES Step 3: Plug Apple lightning cable into the lightning socket on PCB. a. Put the bracket over the back enclosure as shown to line up the holes. Then Ziptie the Apple lightning cable onto the enclosure. b. Fasten the provided M6 flat head screws from the other side using a 4 mm Allen wrench. 4 5
5 ENCLOSURE AND DONGLE ASSEMBLY LIGHTED ENCLOSURES Step 4: Place ipad flat into the front enclosure in correct direction, as the picture shows below. The switch/camera should be in alignment with the hole on the enclosure. Note: *** Add downgrade foams provided to support the ipad if version 1-3 of ipad mini is used. Note: *** Add provided downgrade foams to support the ipad if version 1-3 of ipad mini is used. ipad mini 1-3 Foams from downgrade hardware kit 6 7
6 ENCLOSURE AND DONGLE ASSEMBLY LIGHTED ENCLOSURES Step 5: After lining up the top edge of both halves, plug the Kronos lightning cable into the lightning socket and the audio jack into the ipad. Before closing the enclosure, ensure the ipad is pointing in the correct direction. Step 6: Fasten the provided M3 flat head screws using a No.2 Phillips screwdriver. Note: *** Make sure the LED light is not pinched. This can be avoided by gently pressing on it. Note: *** Power up the ipad using the home button if it is in sleep mode. The power button can be accessed via a paper clip using the method shown below. Verify that the ipad is charging. If not ensure the PoE switch has been turned on for this particular location. 8 9
7 Step 7: Plug the RJ45 connector from the power source in the socket on Kronos lighted enclosure. Choose one of the three mounting options: rear-offset mount, side mount and surface mount, then follow the specific guide for the chosen mounting option. 2 ENCLOSURE AND DONGLE ASSEMBLY SLIM ENCLOSURE 10
8 ENCLOSURE AND DONGLE ASSEMBLY SLIM ENCLOSURE The instructions below highlight our recommended installation method when installing Kronos Slim Enclosures. INSTALLATION STEPS Step 1: Install appropriate bracket (0 or 15 degrees) to the slim enclosure. The guide only shows 15-degree bracket. Insert the M6 flat head screws provided into the threaded holes using a 4 mm Allen wrench. Step 2: Plug in the Lightning cable into the socket on the Slim Enclosure. Plug the other end of the cable into the USB port in the PoE-to-USB unit. Put the spacers on the right position for installing the PoE unit. Note: ***For Wired-Ethernet option, refer the installation steps for slim enclosure in section
9 ENCLOSURE AND DONGLE ASSEMBLY SLIM ENCLOSURE Step 3: Install the PoE unit onto the Slim Enclosure using the 2 supplied M3 screws and spacers. Note: *** Plug in the RJ45 connector whenever the whole assembly is ready to go on the wall Step 4: Peel off the liner of 3M VHB tape. Step 5: Place the ipad onto the enclosure and plug the flat lightning cable into the ipad. Note: *** For Wired-Ethernet option, refer the installation steps for slim enclosure in section 3. Slide the ipad in place until the flat Lightning cable slide in its cutout and the ipad lays flat into the enclosure
10 ENCLOSURE AND DONGLE ASSEMBLY SLIM ENCLOSURE Step 6: Fasten the provided M3 set-screw using a 1.5 mm Allen wrench. Note*** the set-screw head should stop flush with the outside surface of the enclosure. Moving the set-screw all the way in would result in damage to the ipad. Step 7: Plug the RJ45 connector from the power source in the socket on Kronos lighted enclosure. Choose one of the three mounting options: rear-offset mount, side mount and surface mount, then follow the specific guide for the chosen mounting option. Note: Power up the ipad using the home button if it is in sleep mode. The power button can be accessed via a paper clip using the method shown below. Verify that the ipad is charging. If not ensure the PoE switch has been turned on for this particular location
11 ENCLOSURE ASSEMBLY WIRED-ETHERNET DONGLE The instructions below highlight our recommended installation method when installing Kronos Wired-Ethernet Dongle for both Lighted and Slim Enclosures. INSTALLATION STEPS LIGHTED ENCLOSURE 1. Start with all the following parts prepared in which are included in Kronos Enclosures package: a. Enclosure with appropriate bracket (Lighted with 15 degrees shown) b. Kronos wired-ethernet dongle c. ipad USB to Lightning cable A 3 ENCLOSURE ASSEMBLY WIRED-ETHERNET DONGLE C B 19
12 ENCLOSURE ASSEMBLY WIRED-ETHERNET DONGLE 2. Plug the ipad lightning cable into the socket on Kronos WiredEthernet dongle (1A). Plug the lightning cable of Kronos WiredEthernet dongle into the socket on the Lighted Enclosure (1B). Plug the USB end of ipad cable into the USB port in the circuit board (1C). 3. Put the connected parts in available space of the lighted enclosure, as shown below. Then the RJ-45 connector from the dongle into the Kronos RJ-45 socket (2). 1B 2 4. After the previous setup, install the Ethernet Dongle cover bracket as shown. 1C 1A 20 21
13 Kronos Lighted Enclosure is ready to go, please follow section 4 to 7 for mounting guide ENCLOSURE ASSEMBLY WIRED-ETHERNET DONGLE 2. Plug the camera adapter s lightning cable into the female side on the enclosure. Note: *** For the customers with premium service, the bracket and the Wired-Ethernet dongle are pre-installed. For additional information reach out to our support team at info@magtarget.com 3. Install the PCB board set onto the enclosure. Note: *** picture only shown 0 degree mounting bracket, but 15 degree mounting bracket is also applicable. SLIM ENCLOSURE 1. Start with plugging in lightning cable into the PCB board (1A and 1B). 1A 1B 22 23
14 ENCLOSURE ASSEMBLY WIRED-ETHERNET DONGLE 4. Plug in Wired-Ethernet dongle for either 15-degree mounting option or 0-degree mounting option: 4A. Data output of th Wired- Ethernet power-data splitter goes into the USB-Ethernet adapter. 4B. Power output of the Wired-Ethernet power-data-splitter goes into the PCB board Ethernet female plug. For 0 Degree Mounting option, the spacing will be tighter than 15 degree, tilt the Wired-Ethernet power-data splitter as shown in the picture to perform a easier mounting installation. Follow section 4 to 7 for mounting guide. 4B 15 Degree Mounting Option 0 Degree Mounting Option Setup Note: *** For the customers with premium service, the bracket and the Wired-Ethernet dongle are pre-installed. 4A NOTES: This installation should be performed by a skilled professional. MagTarget is not responsible for damages resulting from improper installation. For additional information reach out to our support team at info@magtarget.com 24 25
15 REAR-OFFSET The instructions below highlight our recommended installation method for rear-offset mounting options suitable for every version of Kronos enclosure. Follow this guide when fastening Kronos enclosures to aluminum extrusions such as in door frame/mullion. 4 REAR-OFFSET 27
16 REAR-OFFSET INSTALLATION STEPS Step 1: a. Download and print the Drill Guide from Guide that correspond to the bracket purchased. Ensure the drill guide template is printed at full scale using the Actual Size option in Acrobat Reader*** b. Temporarily hold the Drill Guide on the desired location and height. Check local regulation to see if any rules apply to the height of the enclosure. In the USA the Americans with Disability Act (ADA) asks for a maximum reach height of 48 inches*** Step 2: a. Drill pilot holes with a small diameter drill bit per the Drill Guide. b. Drill full size holes as per Drill Guide. c. Install M6 rivet nuts. (sold separately) Step 3: Bolt the bracket tightly into place using M6 screws
17 REAR-OFFSET Step 4: If not already run through the mullion, run the PoE network cable. As shown on the picture below. Install the cover piece at the same time. Step 5: To get ready to install the Kronos enclosure, one or two of the M3 screw can be screwed into the top edge of the bracket for making one-person installation easier
18 REAR-OFFSET Step 6: a. Plug in the PoE cable into the port in the back of the enclosure. b. Slide ipad enclosure assembly onto the bracket (enclosure not shown for clarity) c. Ensure the ipad is receiving power. If not check if the PoE port is activated. d. Insert the remaining M3 fasteners to secure the enclosure in place. This complete the installation of the MagTarget Kronos enclosure (rear-offset). Lighted Kronos Enclosure is shown here, but other types of enclosures can be installed using the same methods
19 SIDE-MOUNT The instructions below highlight our recommended installation method for side mounting options suitable for every version of Kronos enclosure. Follow this guide when fastening Kronos enclosures to aluminum extrusions such as in door frame/mullion. 5 PREFERRED MOUNTING METHODS SIDE-MOUNT 35
20 SIDE-MOUNT INSTALLATION STEPS Step 1: a. Download and print the Drill Guide from Guide that correspond to the bracket purchased. Ensure the drill guide template is printed at full scale using the Actual Size option in Acrobat Reader*** b. Temporarily hold the Drill Guide on the desired location and height. Check local regulation to see if any rules apply to the height of the enclosure. In the USA the Americans with Disability Act (ADA) asks for a maximum reach height of 48 inches*** Step 2: a. Drill pilot holes with a small diameter drill bit per the Drill Guide. b. Drill full size holes as per Drill Guide. c. Install M6 rivet nuts. (sold separately) Step 3: Bolt the bracket tightly into place using M6 screws
21 SIDE-MOUNT Step 4: If not already run through the mullion, run the PoE network cable. As shown on the picture below. Install the cover piece at the same time. Step 5: To get ready to install the Kronos enclosure, one or two of the M3 screw can be screwed into the top edge of the bracket for making one-person installation easier
22 SIDE-MOUNT Step 6: a. Plug in the PoE cable into the port in the back of the enclosure. b. Slide ipad enclosure assembly onto the bracket (enclosure not shown for clarity): c. Ensure the ipad is receiving power. If not check if the PoE port is activated. d. Insert the remaining M3 fasteners to secure the enclosure in place. This complete the installation of the MagTarget Kronos enclosure (side). Lighted Kronos Enclosure is shown here, but other types of enclosures can be installed using the same methods
23 SURFACE MOUNT The instructions below highlight our recommended installation method for the Kronos Surface Mount. 6 SURFACE MOUNT 43
24 SURFACE MOUNT INSTALLATION STEPS Step 1: Temporarily hold the Surface Mount at the desired location and height, and mark the selected holes. ***Check local regulation to see if any rules apply to the height of the enclosure. In the USA the Americans with Disability Act (ADA) asks for a maximum reach height of 48 inches*** The inner holes of the Surface Mount highlighted in green below are spaced to fit standard electrical outlet boxes used in North America. For a secure installation we recommend using additional fasteners in the additional holes provided
25 SURFACE MOUNT Step 2: Drill hole into mounting surface and install the bracket. Make sure to use fasteners which correspond with the type of mounting surface (use screw anchors if needed). Route the PoE cable through the center of the bracket and terminate cable at the same time. Step 4: a. Plug in the PoE cable into the port in the back of the enclosure. b. Slide ipad enclosure assembly onto the bracket (enclosure not shown for clarity). c. Ensure the ipad is receiving power. If not check if the PoE port is activated. d. Insert the remaining M3 fasteners to secure the enclosure in place. Step 3: To get ready to install the Kronos enclosure, one or two of the M3 screw can be screwed into the top edge of the bracket for making one-person installation easier
26 This complete the installation of the MagTarget Kronos enclosure (surface). 57 PREFERRED MOUNTING METHODS GLASS MOUNT Lighted Kronos Enclosure is shown here, but other types of enclosures can be installed using the same methods. 48
27 GLASS MOUNT The instructions below highlight our recommended installation method when mounting the Kronos back bracket on the glasses. Step 3: Place the bracket onto the glass, and add sticker to the other side of the glass inside the office for covering. INSTALLATION STEPS Step 1: Use Alcohol Pad provided in the kit to wipe the glass as well as the back of the bracket before putting the VHB tapes on. Step 2: Add four pieces 3M VHB tapes onto the right places of the bracket
EN - 1. Warning Before Installation. Package Contents. Refer to your user s manual for the operating temperature.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or tiny objects
More informationEVOLVE1-M MONITOR ARM
EVOLVE1-M MONITOR ARM EVOLVE1-M Rev A 2/17 Model EVOLVE1-M-SLV Model EVOLVE1-M-BLK Model EVOLVE1-M-WHT ASSEMBLY AND ADJUSTMENT EVOLVE1-M MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before
More informationThe basic product comes with the IRS5 control board, 3 internal cables, 1 external cable with a 5 volt adapter and a mounting bracket with hardware.
Please read these instructions and watch the Installation Video before you proceed with the installation of the PC-IRS5-01. Installation Video: http://youtu.be/os98e32vhb4 The PC-IRS5-01 Infrared Receiver
More informationOutdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
More informationWarning Before Installation. Package Contents EN - 1. Refer to your user's manual for the operating temperature.
510000221G Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or
More informationFITTING INSTRUCTIONS
& This option connects a GL3000 or GL3300 console as a channel expander to a second console with just one or two interconnecting cables. Kit Part No: GL3000-SL1 Single option to install SYS-LINK to one
More informationTech Tub Premium: Holds Up to 10 Tablets
TEC1000 Tech Tub Premium: Holds Up to 10 Tablets Assembly Guide TEC1000_2017_A Check out our other products online at www.copernicused.com For assistance, please contact us: 1-800-267-8494 Email info@copernicused.com
More informationrooms Conference Room Mac Quickstart Guide
rooms Conference Room Mac Quickstart Guide WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT! It is the installers responsibility to make certain
More informationUSBCNC-SW USB Disk Key reader for CNC Controls Machine Mount instructions for Universal Switcher Version
USBCNC-SW USB Disk Key reader for CNC Controls Machine Mount instructions for Universal Switcher Version 2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla Street Chatsworth, CA 91311
More informationInstructions for installing your QuiltCam on your Gammill quilt machine.
Instructions for installing your QuiltCam on your Gammill quilt machine. The items include with your QuiltCam Items included in all packages: QuiltCam Control Box, See Figure 1 Power Supply, Figure 2 Video
More informationANIxx. Installation Manual.
ANIxx Installation Manual www.audac.eu Introduction WaveDynamics Dante audio network interface The ANIxx are Dante audio network interfaces for use with WaveDynamics supporting amplifiers, supporting two
More informationTECHKNOW, INC. Kiosk Order Confirmation System INSTALLATION MANUAL. Revision Date: July 11, 2012 Part # Version 3.2
document Page 1 of 18 TECHKNOW, INC Kiosk Order Confirmation System INSTALLATION MANUAL Revision Date: July 11, 2012 Part # Version 3.2 Techknow, Inc. 393 Mayfield Road Duncan, SC 29334 www.gotechknow.com
More informationTURN-O-MATIC INSTALLATION GUIDE
TURN-O-MATIC INSTALLATION GUIDE WIRELESS SYSTEM WIRELESS SYSTEM (1) Dispenser (1) Dispenser Mounting Bracket (3) Large Slotted Screw (2) Large Slotted Bolt (2) Nut (1) Display Wall Mount Bracket (1) Wireless
More informationAssembly and Setup Manual
M-11 Series Copyboard/C-11 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-11 series/c-11 series. To the Customer Specialized techniques are required
More informationInstalling the Cisco MDS 9020 Fabric Switch
CHAPTER 2 This chapter describes how to install the Cisco MDS 9020 Fabric Switch and its components, and it includes the following information: Pre-Installation, page 2-2 Installing the Switch in a Cabinet
More informationIS-DM220/IR/HB IS-DM220
IS-DM220/IR/HB IS-DM220 Installation Guide Indoor/Outdoor Ver. 1.2 00P6NX223ZXSEA2 Table of Contents 1. Indoor Camera Installation... 3 1.1 Hard Ceiling... 3 1.2 In-Ceiling (T-Bar) Mounting... 13 1.3 4S
More informationWarning Before Installation
Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating temperature. Contact your distributor in the
More informationCarefully remove the translite from the backbox and then lower the speaker panel to the position shown in Fig. A to gain access to the backbox.
Installation Instructions for Data East (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display
More informationMacBook Pro 13" Unibody Mid 2010 SSD Dual Drive Installation
MacBook Pro 13" Unibody Mid 2010 SSD Dual Drive Installation Use this guide to install a second SSD in place of the optical drive. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 13 INTRODUCTION
More informationAdapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout
Installation Instructions Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout Catalog Numbers 2711-NR5T, 2711P-RAT12E2 Topic Page About This Publication 1 Important User Information 2 About
More informationWarning Before Installation. Package Contents EN-1
500024701G English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or
More informationUser s Guide. for RackMac Pro 4U Rack Enclosure for New Mac Pro
User s Guide for RackMac Pro 4U Rack Enclosure for New Mac Pro Contents 1 Introduction 1 2 RackMac Pro Description 2 External Features Computer Mounting Module 5/64-Inch Hex Wrench Mac Pro Bottom Cover
More informationWarning Before Installation. Package Contents EN-1. Power off the Network Camera as soon as smoke or unusual odors are detected.
English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or tiny objects
More informationASSEMBLY AND ADJUSTMENT
EDGE-WALL MONITOR ARM EDGE-WALL Rev A 2/17 Model EDGE-WALL-SLV ASSEMBLY AND ADJUSTMENT EDGE-WALL MONITOR ARM PLEASE REVIEW these instructions before beginning the installation. Check that all parts and
More informationCIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007)
CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007) CIB 3047 Comcode 845-659-325 Issue 1 CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007) This
More informationInstalling the Camera
CHAPTER 2 This chapter provides information and instructions for installing the Cisco Video Surveillance PTZ IP camera, and includes the following topics: Installation Guidelines, page 2-1 Warnings Before
More informationCarefully remove the translite from the backbox and then swing speaker panel to the open position as shown in Fig. A to gain access to the DMD.
Installation Instructions for SEGA (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display graphics
More informationimac Intel 27" Retina 5K Display CPU Replacement
imac Intel 27" Retina 5K Display CPU Replacement Replace or upgrade the CPU in your imac Intel 27" Retina 5K Display. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationWaiting Room Network Installation Manual
Waiting Room Network Installation Manual Version 5.0 March 27 th, 2013 PCM Help Desk 1-877-233-9114 Page 1 Table of Contents System Overview 3 Tool List 4 Installation Guide 5 Site Notification 5 Install
More informationFlat Panel Static Wall Mount MSP-SS (GSM-210)
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount (GSM-2) The static wall mount fits most 23 to 30 displays. The mount was designed to adapt to the VESA 75mm/0mm, 0mm/0mm, and 200mm/0mm compliant
More informationPi PoE Switch HAT Quick Start And FAQ. Getting started. Kit contents
Pi PoE Switch HAT Quick Start And FAQ Getting started The Pi PoE Switch HAT is an add on board for the Raspberry Pi that brings the Switch technology together with PoE all in one fantastic package! You
More informationSystem Storage EXP3000 Rack Installation Instructions
System Storage EXP3000 Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When you install the IBM System Storage EXP3000 in a
More informationWarning Before Installation. Package Contents EN - 1. Refer to your user s manual for the operating temperature.
5000020G Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Do not place the Network Camera on unsteady surfaces. Do not insert sharp or tiny
More information7" Touch Screen Display
7" Touch Screen Display Installation Guide Contents Minimum Requirements...1 Select a Location...1 Initial Setup...2 Unboxing...2 Installation...3 Prepare the Panel...3 Install the Mounting Plate...3 Mount
More information300 Series Mini Dome IP-Enabled HD Surveillance Camera with Microphone. Installation Manual. Important! Ensure your NVR has the latest firmware!
300 Series Mini Dome IP-Enabled HD Surveillance Camera with Microphone Installation Manual Important! Ensure your NVR has the latest firmware! Read this page before you go to the job site! 2 For maximum
More informationEWS660AP. Quick Installation Guide
Package contents - Managed indoor access point - Power adapter - RJ-45 Ethernet cable - Mounting bracket - Mounting kit - T-Rail mounting kit IP Adress configuration Step 1: Once your computer is on, ensure
More information1. Move the cardboard carton close to the installation site, making sure you have adequate space to remove all the contents of the box.
Install the vedge 1000 Router Once you have prepared your site for router installation, unpack the vedge 1000 router. If you plan to install the router in a 19-inch rack, unpack the rack-mount kit as well
More informationInnovative Americans, LLC. HD Media Pack Installation Manual
Innovative Americans, LLC HD Media Pack Installation Manual Please read this manual before you begin! Your installation will be EASIER and SAFER if you take a few moments to read this document!! Proudly
More informationTASER Axon Dock Installation Manual IMPORTANT SAFETY INSTRUCTIONS
TASER Axon Dock Installation Manual IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions. Save these instructions. The most up-to-date warnings and instructions are available at www.taser.com
More informationTDM To MiniMech conversion ProceDure
TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT
More informationimac Intel 27" EMC 2639 Hard Drive
imac Intel 27" EMC 2639 Hard Drive Replacement Replace the Hard Drive in your imac Intel 27" EMC 2639. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replacing the
More informationAirLink GX Series X-Card Installation Guide
This installation is to be performed only by certified Sierra Wireless AirLink distributors. If it is performed by anyone other than the certified AirLink distributor, the terms of the warranty agreement
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationHow to Upgrade the Hard Drive in a 24 imac (2007-Early 2009)
Instructional Video Series How to Upgrade the Hard Drive in a 24 imac (2007-Early 2009) Skill Level: Involved Time to Complete: Approximately 45 Minutes Required Tools: Small Phillips Screwdriver Torx
More informationInstallation Instructions. for RackMac Pro Computer Mounting Module
Installation Instructions for RackMac Pro Computer Mounting Module Contents 1 Product Description 1 Computer Mounting Module 5/64-Inch Hex Wrench Mac Pro Bottom Cover Label 2 Mac Pro and Computer Mounting
More informationNextiva S FD Models
Nextiva S5100 - FD Models Quick Installation Guide All users should read the user manuals for complete details on installation, usage and functionality. Hardware Overview The S5120FD features a 2-Megapixel
More informationInstallation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays
Installation and Assembly: 2 x 2 Video Wall Ceiling Mount for 40" - 55" flat Panel Displays Model: DS-VWT955-2X2 EXTENSION COLUMN (SOLD SEPARATELY) COMPATIBILITY Display width must be a minimum of 36"
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More information700 Series Dome 500 Series Dome IP-Enabled HD Surveillance Camera. Installation Manual. Important! Ensure your NVR has the latest firmware!
700 Series Dome 500 Series Dome IP-Enabled HD Surveillance Camera Installation Manual Important! Ensure your NVR has the latest firmware! Read this before you go on site! For maximum control and convenience,
More informationSSD Dual Drive Installation
SSD Dual Drive Installation Replace the optical drive in your imac Intel 21.5". Written By: Dozuki System 2017 guides.crucial.com Page 1 of 18 INTRODUCTION imac won't read disks? Use this guide to replace
More informationView Wall Interface. Dynamic Glass INSTALLATION GUIDE. Description. System Requirements. Installation Overview
Description The solution is a compact, wall-mounted interface used for monitoring and changing the tint levels of View Dynamic Glass. The product leverages 802.11-based Wi-Fi technology for connectivity
More informationInstalling the DX LCD Display
DX LCD Display User s Guide 3-1 Chapter 3 Installing the DX LCD Display Introduction Use the DX LCD Display as either a portable device, or permanently mount it in a panel or on the wall. For panel and
More informationAP65 Access Point. The Aruba AP65 Access Point is a compact Tri-Band Wireless Unit supporting the a, b and g WiFi standards.
AP65 Access Point The Aruba AP65 Access Point is a compact 802.11 Tri-Band Wireless Unit supporting the 801.11a, 801.11b and 801.11g WiFi standards. The AP65 is designed to be directly mounted on a standard
More informationInstalling MacBook Pro 15" Unibody Mid 2009 Dual Hard Drive
Installing MacBook Pro 15" Unibody Mid 2009 Dual Hard Drive Use this guide to install a second hard drive in place of the optical drive. Written By: Brittany McCrigler ifixit CC BY-NC-SA www.ifixit.com
More informationEaton LCD Lift Flat Panel Display System. Installation Guide
Eaton LCD Lift Flat Panel Display System Eaton LCD Lift Flat Panel Display System Installation Guide Copyright 2011 Eaton Corporation, Worcester, MA, USA. All rights reserved. Information in this document
More information2M Outdoor Motorized Bullet Camera
2M Outdoor Motorized Bullet Camera 8608586000010 Quick Installation Guide Please follow the installation steps below to set up your 2MP Bullet IP Camera. Check the package contents against the list below.
More informationTIMETRAX SYNC PoE DIGITAL CLOCK Installation Instructions
Installation Instructions OVERVIEW Thank you for choosing a TimeTrax Sync PoE Clock System. The TimeTrax PoE Clock System is capable of receiving both its time and power from a cost-effective and reliable
More informationimac Intel 21.5" EMC 2389 SSD Dual Drive
imac Intel 21.5" EMC 2389 SSD Dual Drive Installation Use this guide to install a second SSD in place of the optical drive. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 17 INTRODUCTION There
More informationFloat Pod Installation Manual
Float Pod Installation Manual TABLE OF CONTENTS What to do before receiving the pod..page 3 Receiving the pod...page 5 Installing UV..Page 9 Control Box. Page 12 Intercom....Page 14 Audio.. Page 16 Pod
More informationRack Installation Instructions
Rack Installation Instructions For System Storage EXP2512 and EXP2524 Express Storage Enclosures Use the instructions in this document to install an IBM System Storage EXP2512 Express Storage Enclosure
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CASSETTE/MP3 (EX) 2006 PILOT All 30488 Issue Date SEP 2005 Player Attachment Kit (sold separately) : P/N 08B06-S9V-100A Cassette Player
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationLED Lighting Kit For Elara NanoEdge Fixed Frame. Installation Guide. Attention: Read this guide before assembling your screen.
LED Lighting Kit For Elara NanoEdge Fixed Frame Installation Guide Attention: Read this guide before assembling your screen. INTRODUCTION GETTING STARTED WARNING - Sharp Edges This product may contain
More informationInstalling MacBook Pro 17" Unibody Dual Hard Drive
Installing MacBook Pro 17" Unibody Dual Hard Drive Written By: Dozuki System 2017 guides.crucial.com Page 1 of 13 INTRODUCTION There are many benefits to adding a second hard drive to your laptop such
More informationCycles Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
Recumbent Upright Cycles Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 4 Obtaining Service... 4 Unpacking the
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationimac Intel 27" Retina 5K Display SATA Cable
imac Intel 27" Retina 5K Display SATA Cable Replacement Written By: Dozuki System 2017 guides.crucial.com Page 1 of 32 INTRODUCTION Use this guide to replace the SATA cable on the back of the logic board
More informationOne Arm Articulating TV Wall Mount
One Arm Articulating TV Wall Mount Item No: 6360710 MIN:3.07 in / 78 mm MAX:21.65 in / 550 mm MIN: 2.95 x 2.95 in / 75 x 75 mm MAX:3.9 x 3.9 in / 100 x 100 mm 1 Braided HMI 3 Ethernet Cable (6 ft.) Congratulations
More informationWall Mount Kit for Touch Panel Controller. Installation Guide
Wall Mount Kit for Touch Panel Controller Installation Guide Table of Contents Getting Started... 1 SKUs Used... 2 Connections... 3 Powering a Touch Panel Controller... 3 Communication Connections... 3
More informationPlease read thoroughly before starting installation and check that kit contents are complete.
Chrysler/Dodge/Jeep Remote Add-On CD player for RA1, RA2, RA3, or RA4 radios (Kit # 5000-8750) 2013-current RAM truck and Viper; 2015-current Charger, Challenger, and 300; 2017 Pacifica Please read thoroughly
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More information300 Series Mini Bullet IP-Enabled HD Surveillance Camera. Installation Manual. Important! Ensure your NVR has the latest firmware!
300 Series Mini Bullet IP-Enabled HD Surveillance Camera Installation Manual Important! Ensure your NVR has the latest firmware! Read this before you go on site! For maximum control and convenience, install
More informationOwner s s Manual. G5 SATA Double Drive Internal Mounting Kit. Apple Macintosh G5. Add 2 SATA drives to the G5
Owner s s Manual Add 2 SATA drives to the G5 G5 SATA Double Drive Internal Mounting Kit Apple Macintosh G5 SATA (Serial ATA) 2 Internal Drive System Table of Contents User Guide Page How SATA (Serial ATA)
More informationTailgates Conracks Sunshades
Aluminum Accessories Tailgates Conracks Sunshades 15168 BACKUP CAMERA KIT 2009 THRU 2013 Ford F-150 NOTE: This kit is ONLY for Ford F-150 pickups that already have the factory back up camera option The
More information7403 K321. Display Wall Mount. Kit Instructions. Issue A
7403 K321 Display Wall Mount Kit Instructions Issue A ii Revision Record Issue Date Remarks A Nov 2008 First issue 1 Introduction This kit is used in to secure a 7403 Display Head on a vertical surface.
More informationInstallation Guide. Universal Camera Mount Bracket
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Universal Camera Mount Bracket The purpose of this guide is to describe the assembly and
More informationDaNI Robot Camera. User Guide V0512
DaNI Robot Camera User Guide 60018 V0512 Materials Included Camera (includes hardware that will not be used) Modem (with power supply that will not be used) Power converter 6" Velcro strip Adhesive tab
More informationPrint Mechanism Maintenance Kit
Print Mechanism Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the print mechanism maintenance kit in the following printers: ZT0 ZT0 ZT0 Read
More informationForeseesons Monitor Installation Instructions
Foreseesons Monitor Installation Instructions Visit the Merit Entertainment Web site http://www.meritind.com PM0626-04 Table of Contents Parts List... p. 1 Cabinet Identification... p. 1 Cabinets with
More informationAssembly and Setup Manual
M-12 Series Copyboard / C-12 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-12 series Copyboard and C-12 series Captureboard. (The copyboard and/or
More information2M IR Mini Dome Quick Installation Guide
1 2M IR Mini Dome Quick Installation Guide Please follow the installation steps below to set up 2M IR Mini Dome IP Camera. Check the package contents against the list below. See P.1 Physical overview.
More informationG12/G12x USER S MANUAL
G12/G12x USER S MANUAL TABLE OF CONTENTS SECTION 1 SLIDE CONFIGURATION SECTION 2 SLIDE CONFIGURATION ACCESSORIES SECTION 3 TABLETOP CONFIGURATION SECTION 4 TABLETOP CONFIGURATION ACCESSORIES SECTION 5
More informationWritten By: Andrew Optimus Goldberg
Use this guide to install a second hard drive or SSD in place of the optical drive. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION There are many benefits
More informationInstalling MacBook Pro 15" Unibody Mid 2010 Dual Hard Drive
Installing MacBook Pro 15" Unibody Mid 2010 Dual Hard Drive Use this guide to install a second hard drive in place of the optical drive. Written By: Brittany McCrigler ifixit CC BY-NC-SA www.ifixit.com
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationThanks for shopping with Improvements! Chalet Standard Mailbox Item # (With 1 Line Plaque) Item # (With 2 Line Plaque)
Thanks for shopping with Improvements! Chalet Standard Mailbox Item #476200 (With 1 Line Plaque) Item #476242 (With 2 Line Plaque) To order, call 1-800-642-2112 West Chester, OH 45069 Made in China 1014
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationEncore XT Manual Gun Upgrade Kit
Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.
More informationExtra Large Full Motion TV Mount for Televisions
8008981 TV Size Range: 47 ~ 84 Maximum Weight Capacity: 60 kg/132 lbs Maximum Mounting Pattern: 800 mm x 600 mm (31.4 x 23.6 ) Distance to the Wall: 5.5-45 cm Extra Large Full Motion TV Mount for 47-84
More informationML200 Fanless Mini-ITX Enclosure
ML200 Fanless Mini-ITX Enclosure Assembly Guide Version 1.1 PN: ML200 1 Table of Contents I. Product Description... 3 II. Included Parts... 3 III. Basic Chassis Assembly... 5 IV. Installation... 12...
More informationQuad Monitor Desk Stand - 13" to 24" Installation Instructions
Quad Monitor Desk Stand - 13" to 24" Installation Instructions 04-0885A 1 Unpacking Carefully remove the contents and lay out on cardboard or other protective surface Check package contents against the
More informationCisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2. Cisco CRS 3-Phase AC Power Distribution Unit 2
Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2 Cisco CRS 3-Phase AC Power Distribution Unit 2 Revised: November 18, 2016,
More informationInstallation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL)
Installation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL) Installation Time: 1 Hour Tools Required Trim removal tool (plastic or wood to prevent scratches on the paint)
More informationQuick Installation Guide
FD8372 Fixed Dome Network Camera Quick Installation Guide English 繁中簡中日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska 5MP Full HD Smart Focus System Warning Before Installation
More informationFortiCam FD40 Mounting Guide
FortiCam FD40 Mounting Guide 1 FORTINET DOCUMENT LIBRARY http://docs.fortinet.com FORTINET VIDEO GUIDE http://video.fortinet.com FORTINET BLOG https://blog.fortinet.com CUSTOMER SERVICE & SUPPORT https://support.fortinet.com
More informationPracticeWire Installation Manual
PracticeWire Installation Manual Version 5.0 August 28 th, 2013 PCM Help Desk 1-877-233-9114 Page 1 Table of Contents System Overview 3 Tool List 4 Installation Guide Site Notification 5 Install Universal
More information