1. Checking the Box Contents 2. Moving the System U

Size: px

Start display at page:

Download "1. Checking the Box Contents 2. Moving the System U"

Geoffrey Cook
5 years ago
Views:

1 . Checking the Box Contents. Moving the System U Use these items for installation... To move your system unit, grasp product medallion and pull th CAUTION: Two people are requ be lifted using the ha at the top. Monitor Video Cable Monitor Power Cord System Unit Keyboard/Mouse Extension Cable Owner s Guide, Options Guide, Other Documentation Mouse with Mousepad Keyboard System unit System Power Cord For more information about starting your system, see Chapter 6 of the DEC 000 Model 400/400S Owner s Guide that accompanies your system. Universal Strain Relief Strap Keys (Attached to System Unit) Headset Ethernet Loopback Connector MLO-0085 Save these items for use later... Network Label 0BASE-T Loopback Connector

2 . Choosing a Location 4. Connecting the Univ Choose the location of your workstation, keeping the following requirements in mind: System unit dimensions (see diagram) Connect the universal strain reli using the instruction sheet accom relief strap. Ventilation at least 7.6 cm ( inches) of air space on all sides Power outlet within.8 meters (6 feet) Adequate space for cables and connectors on rear of system unit 7.6 cm ( inches) 6 cm (5 inches) 75 cm (9 inches) cm ( inches) MLO-00759

3 5. Connecting the Monitor Cables Complete these steps: Step for a color monitor. Step for a monochrome or greyscale monitor. Step for all monitors. Step See diagram with... Then... Three connectors (color monitor) Connect all three cable connectors to the monitor, matching the color cables, red (R), green (G), and blue (B), with the corresponding connectors marked R, G, and B on the monitor. Five connectors (color monitor) Do not use the H/C and V connectors. Connect the other three cable connectors as described above. Six connectors (Video In and Video Out) One connector (monochrome or greyscale monitor) Use the three Video In connectors. Connect the three cable connectors as described above. Connect only the middle, green (G) cable connector to the monitor. Monitor power cord Connect the monitor power cord to the power socket on the rear of your monitor. The power socket may be in a different location than the position shown here. Connect the cable Connect the cable Connect the monito R G B

4 6. Connecting the Rear Cables and Connectors Step: Connect the... To the... 4 Ethernet loopback connector AUI Ethernet port Keyboard/mouse cable Keyboard/mouse port Monitor video cable Graphics port System power cord System power socket ISDN S 4 7. Setting the Switches Make sure the S switch on the r as shown: Alternate console switch to 4 5 0

5 8. Connecting the Keyboard and Mouse Connect the keyboard cable and the mouse cable to the ports on the mouse/keyboard extension cable. To secure the extension cable, place the Mylar tab under the base of the monitor. MLO Checking the Conne Make sure that the power On/Off before plugging the other end of t outlet of the correct voltage. Che

6 0. Starting the System Turn on the system in the following order:. Monitor. Any expansion box. System unit If there was a yellow label covering the system power socket, your system has been preloaded with operating system software. If you... Then refer to... Ordered OpenVMS Alpha AXP operating system Ordered DEC OSF/ AXP operating system Need more detailed information about installing or starting your system OpenVMS Factory Installed Software User Information, provided with your system. DEC OSF/ AXP Factory-Installed Software User Information, provided with your system. DEC 000 Model 800/800S/900 AXP Owner s Guide, provided with your system.

DEC 3000 Model 300 Series AXP

DEC 3000 Model 300 Series AXP Adding Memory Part Number: EK PELAM IC. C0 Introduction Your DEC 3000 Model 300 series AXP system is configured at the factory with 3 to 56 megabytes of memory, depending