XMC 2Go Kit with XMC1100

Transcription

1 Evaluation Board For XMC1000 Family Kit Version 1.0 Board User s Manual Revision 1.0, Microcontroller

2 Edition Published by Infineon Technologies AG Munich, Germany 2014 Infineon Technologies AG All Rights Reserved. Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Information For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office ( Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered.

3 XMC 2Go Revision History Page or Item Revision 1.0, Subjects (major changes since previous revision) Initial release Trademarks of Infineon Technologies AG AURIX, C166, CanPAK, CIPOS, CIPURSE, EconoPACK, CoolMOS, CoolSET, CORECONTROL, CROSSAVE, DAVE, EasyPIM, EconoBRIDGE, EconoDUAL, EconoPIM, EiceDRIVER, eupec, FCOS, HITFET, HybridPACK, I²RF, ISOFACE, IsoPACK, MIPAQ, ModSTACK, my-d, NovalithIC, OptiMOS, ORIGA, PRIMARION, PrimePACK, PrimeSTACK, PRO-SIL, PROFET, RASIC, ReverSave, SatRIC, SIEGET, SINDRION, SIPMOS, SmartLEWIS, SOLID FLASH, TEMPFET, thinq!, TRENCHSTOP, TriCore. Other Trademarks Advance Design System (ADS) of Agilent Technologies, AMBA, ARM, MULTI-ICE, KEIL, PRIMECELL, REALVIEW, THUMB, µvision of ARM Limited, UK. AUTOSAR is licensed by AUTOSAR development partnership. Bluetooth of Bluetooth SIG Inc. CAT-iq of DECT Forum. COLOSSUS, FirstGPS of Trimble Navigation Ltd. EMV of EMVCo, LLC (Visa Holdings Inc.). EPCOS of Epcos AG. FLEXGO of Microsoft Corporation. FlexRay is licensed by FlexRay Consortium. HYPERTERMINAL of Hilgraeve Incorporated. IEC of Commission Electrotechnique Internationale. IrDA of Infrared Data Association Corporation. ISO of INTERNATIONAL ORGANIZATION FOR STANDARDIZATION. MATLAB of MathWorks, Inc. MAXIM of Maxim Integrated Products, Inc. MICROTEC, NUCLEUS of Mentor Graphics Corporation. Mifare of NXP. MIPI of MIPI Alliance, Inc. MIPS of MIPS Technologies, Inc., USA. murata of MURATA MANUFACTURING CO., MICROWAVE OFFICE (MWO) of Applied Wave Research Inc., OmniVision of OmniVision Technologies, Inc. Openwave Openwave Systems Inc. RED HAT Red Hat, Inc. RFMD RF Micro Devices, Inc. SIRIUS of Sirius Satellite Radio Inc. SOLARIS of Sun Microsystems, Inc. SPANSION of Spansion LLC Ltd. Symbian of Symbian Software Limited. TAIYO YUDEN of Taiyo Yuden Co. TEAKLITE of CEVA, Inc. TEKTRONIX of Tektronix Inc. TOKO of TOKO KABUSHIKI KAISHA TA. UNIX of X/Open Company Limited. VERILOG, PALLADIUM of Cadence Design Systems, Inc. VLYNQ of Texas Instruments Incorporated. VXWORKS, WIND RIVER of WIND RIVER SYSTEMS, INC. ZETEX of Diodes Zetex Limited. Last Trademarks Update Template: IFX_Template_ dot

4 Table of Contents XMC 2Go Table of Contents Introduction Overview Key Features Block Diagram Hardware Description Power Supply Pin Header Connector User LEDs Debugging and UART Communication Production Data Schematics Components Placement and Geometry List of Material Board Users Manual 4 Revision 1.0,

5 List of Figures XMC 2Go List of Figures Figure 1 Block Diagram of the XMC 2Go Kit... 8 Figure Figure 3 Pinning of Pin Header Figure 4 Recommended Installation Options for the J-Link driver Figure 5 Schematic of the Figure 6 Components Placement and Geometry Board Users Manual 5 Revision 1.0,

6 XMC 2Go List of Tables List of Tables Table 1 Features of the... 7 Table 2 Pins used for the User LEDs Table 3 XMC1100 Pins used for Debugging and UART Communication Table 4 List of Material Board Users Manual 6 Revision 1.0,

7 XMC 2Go Overview Introduction This document describes the features and hardware details of the XMC 2Go equipped with the ARM Cortex - M0 based XMC1100 Microcontroller from Infineon Technologies AG. 1 Overview The XMC 2Go is designed to evaluate the capabilities of the XMC1100 Microcontroller and the powerful, free of charge tool chain DAVE. This board is not cost optimized and does not serve as a reference design. 1.1 Key Features Table 1 summarizes the features of the XMC 2Go. Table 1 Topic Processor Flash RAM Clock Generation Frequencies Dimensions Features of the Features XMC1100 microcontroller (ARM Cortex -M0 based) in a 4 x 4 mm VQFN-24 package 64 kb 16 kb Internal Oscillator 32 MHz CPU clock, 64 MHz Timer clock 14.0 x 38.5 mm Power Supply from USB via Debug probe (J-Link) or 3.3V external power Connectors Two 8-pin header (pin pitch: 2.54 mm 0.1 / between rows: mm 0.4 ) Pin header fits to breadboard Debugger Peripherals On-Board J-Link Debugger supports Serial Wire Debug (SWD, ARM Standard) Single Pin Debug (SPD) UART-to-USB bridge (virtual COM) Mapped to pin header X1/X2: 2 Channel USIC (UART, SPI, I2C, I2S, LIN) 6 Channel Analog to Digital Converter (12-Bit resolution) 4 x 16-Bit Timer External Interrupts (via ERU) Others: Real Time Clock Random Number Generator Others 2 User P1.0 and P1.1 Board Users Manual 7 Revision 1.0,

8 XMC 2Go Overview 1.2 Block Diagram The block diagram in Figure 1 shows the main components of the XMC 2Go Kit including the power supply concept. There are following main building blocks: XMC1100 Microcontroller in a 4x4mm VQFN24 package On-board USB debugger realized with a XMC4200 Microcontroller for serial wire debug (SWD) and UART-to-USB Bridge Two 8 pin header X1 and X2 On-board power generation for power supply of the XMC1100 Microcontroller and the debug IC 2 User LEDs 8-Pin Header X1 P2.7/P2.8, P2.9, P2.10, P2.11, P0.0, P0.5 X1 +5V Voltage Regulator ADC, CCU4, USIC, ERU0 EVR +3.3V +3.3V LED2 LED1 P1.1 P1.0 GPIO XMC1100 VQFN24 32MHz Cortex M0 64kB Flash, 16kB RAM 4 x16-bit timer, 6 Ch 12-bit ADC 2 Ch USIC (UART, SPI, I2C, I2S, LIN) BSL USIC Debug, USIC P2.1 P2.2 P1.2 P1.3 UART SWD XMC4200 Debug IC Micro USB X101 ADC, CCU4, USIC, ERU0 Debug LED X2 Figure 1 8-Pin Header X2 P0.6-P0.9, P0.14, P0.15, P2.0, P2.6 Block Diagram of the XMC 2Go Kit XMC 2Go-V1 Kit XMC1100 in VQFN24 Block_Diag.emf Board Users Manual 8 Revision 1.0,

9 XMC 2Go Hardware Description 2 Hardware Description The following sections give a detailed description of the board hardware and how it can be used. Figure 2 shows the components of the. Pin Header X1 XMC4200 Debug IC and UART to USB Bridge User P1.1 Crystal for Debug IC Voltage Regulator & Reverse Current Protection Diode Pin Header distance fits to Breadboard User P1.0 XMC1100 Microcontroller ESD Protection Diode Pin Header X2 Power & Debug LED Micro USB Components.emf Figure Power Supply The XMC 2Go Kit must be supplied by an external 5 Volt DC power supply connected to the Micro UBS plugs (X101). Out of the box with the pre-programmed application and the on-board debugger in operation the XMC 2Go typically draws about 75 ma. This current can be delivered via the USB plug of a PC, which is specified to deliver up to 500 ma. The Power&Debug LED indicates the presence of the generated 3.3V supply voltage. An on-board reverse current protection diode will ensure safe operation and protects the USB port of the Laptop/PC in case power is provided through the pin header X1. If the board is powered via the USB plug, it s not recommended to apply an additional power supply to the VDD pin of X1 (3.3V), because this power supply could drive against the on-board power supply. The VDD pin can be used to power an external circuit. But care must be taken not to draw more current than 150 ma, which is the maximum current the on-board voltage regulator can deliver. After power-up the Debug LED starts blinking. In case there is a connection to a PC via the Debug USB plug X101 and the USB Debug Device drivers are installed on this PC, the Debug LED will turn from blinking to constant illumination. Board Users Manual 9 Revision 1.0,

10 XMC 2Go Hardware Description 2.2 Pin Header Connector The pin headers X1 and X2 can be used to extend the evaluation board or to perform measurements on the XMC1100. The order of pins available at X1 and X2 corresponds to the pinning schema of the XMC1100 Microcontroller in the TSSOP-16 pin package. The pinning table is also printed onto the bottom side of the PCB. P0.5 P V P2.11 P2.10 P2.9 P2.7 X1 X2 P2.6 P2.0 P0.15 P0.14 P0.9 P0.8 P0.7 P0.6 Pin_Header.emf Figure 3 Pinning of Pin Header 2.3 User LEDs The port pins P1.0 and P1.2 of the XMC1100 on the XMC 2Go Kit are connected to LEDs exclusively. Table 2 Pins used for the User LEDs LED Port Pin LED1 P1.1 LED2 P1.0 Board Users Manual 10 Revision 1.0,

11 XMC 2Go Production Data 2.4 Debugging and UART Communication The on-board debugger supports 2-pin Serial Wire Debug (SWD), Single Pin Debug (SPD) and UART communication. Both require the installation of Segger s J-Link Driver which is part of the DAVE installation. DAVE is a high-productivity development platform for the XMC microcontroller families to simplify and shorten SW development. It can be downloaded at The latest Segger J-Link Driver can be downloaded at During installation of the J-Link driver you will be asked for the installation of optional components. For support of the UART communication take care to install the CDC USB driver (Composite Device Class). Therefore select the option Install USB Driver for J-Link-OB with CDC as shown in Figure 4. Figure 4 Recommended Installation Options for the J-Link driver The XMC1100 on the XMC 2Go Kit is configured to SWD1 mode. Use the BMI Get Set tool integrated into DAVE to configure the XMC1100 to e.g. SPD1 mode if required. Take care: Unintended use of the BMI Get Set tool can cause the XMC 2Go Kit not to work anymore, e.g. when configuring the XMC1100 to SWD0, SPD0 mode or to productive user mode. Note: Do not configure the XMC1100 on the XMC 2Go Kit to SWD0, SPD0 or to productive user mode. Table 3 shows the pin assignment of the XMC1100-VQFN24 used for debugging and UART communication. Table 3 XMC1100 Pins used for Debugging and UART Communication Pin Function Input / Output Port Pin Data pin for Debugging via SWD/SPD I/O P1.3 Clock pin for Debugging via SWD O P1.2 Transmit Pin for UART Communication O P2.1 Receive Pin for UART Communication I P2.2 3 Production Data 3.1 Schematics The schematic of the XMC 2Go Kit can be found in Figure 5. Board Users Manual 11 Revision 1.0,

12 C C202 R1 R2 100nF/ uF/ R/ R/0402 C106 C105 C108 C104 C103 C102 C107 R109 10k/ nF/ nF/0402 4,7uF/ nF/ nF/ nF/ uF/0603 P2 P1 C110 C109 D102 ESD8V0L2B-03L R M/0402 D1 D2 15pF/ pF/ ZX62-AB-5PA D101 A C BAS3010A-03W LED101 LED GN/0603 XMC 2Go Production Data A B C D E On-board Debugger including a UART to USB Bridge Configure wiggler-p0.5 as USIC_Tx but only active while X-spy function is selected Configure wiggler-p0.4 as USIC_Rx but only active while X-spy function is selected +3V3 PinHeader XMC V3 P2.7/P2.8 P2.9 P2.10 P V3 P0.0 P0.5 Target Device (XMC1100) TSSOP-16 Pinout X1 X PINHD 8x1 0,1" TH PINHD 8x1 0,1" TH P1.0/LED1 P1.1/LED2 P1.2/SWCLK P1.3/SWD RX_XMC4200 TX_XMC4200 P0.0 P0.5 P0.6 P0.7 P0.8 P0.9 P0.12 P0.13 P0.14 P0.15 P2.0 P2.6 P2.0 P0.15 P0.14 P0.9 P0.8 P0.7 P0.6 P2.6 P2.7/P2.8 P2.9 P2.10 P IC1 P0.0 P0.5 P0.6 P0.7 P0.8 P0.9 P0.12 P0.13 P0.14 P0.15 P1.0 P1.1 P1.2 P1.3 P2.0 P2.1 P2.2 P2.6 P2.8 P2.9 P2.10 P2.11 SWD_IN SWD_OUT SWCLK RXD TXD Debug Connection Concept Q101 SPI Master U0C0 SWD DIR GPIO-P1.3 MISO DX0B-P1.4 MOSI DOUT0-P1.5 CLK_OUT SCLKOUT-P1.1 CS_OUT SELO0-P1.0 SPI Slave U0C1 CS_IN DX2A-P2.3 CLK_IN DX1A-P2.4 PULL Select GPIO-P0.8 ADC AIN P14.9 UART2 (DM2) RXD U1C0 DX0A-P0.4 DOUT0-P0.5 TXD TX_ENABLE GPIO-P0.7 TXACTIVE# GPIO-P0.6 RESET# GPIO-P0.3 DEBUG_LED# DEBUG_LED# GPIO-P0.2 AUX_LED# GPIO-P0.1 R108 +3V3 +3V3 SWCLK 510R/0402 DBG_RESET DBG_TCK DBG_TMS SV IC101 P2.5 P2.4 P2.3 P2.2 P2.1 P2.0 PINHD 1x5 0,05" TH VAREF VA RTC_XTAL_2 RTC_XTAL_1 XTAL2 XTAL1 PORST# TCK TMS VSS XMC4200_QFN48 Digital Analog Hibernate/RTC Supply HIB_IO_0 VBAT DEBUG_LED# SWCLK 100R/0402 USB P0.8 P0.7 P0.6 P0.5 P0.4 P0.3 P0.2 P0.1 P0.0 P1.5 P1.4 P1.3 P1.2 P1.1 P1.0 P14.9 P14.8 P14.7 P14.6 P14.5 P14.4 P14.3 P14.0 USB_D- USB_D+ VDDP2 VDDP1 VDDP VDDC1 VDDC R102 COM LED Level Shifter No RESET Pin UART SPD SWV JTAG R105 R106 R103 R104 33R/ R/ R/ R/ V3 TX_XMC4200 RX_XMC4200 P1.3/SWD P1.2/SWCLK +5V 680R/0402 R101 X101C X101S C nF/ nF/ nF/0402 C1 C2 10 VDD 9 Supply VSS EXP EXP XMC1100_VQFN24 Power Supply +5V 1 4 IC201 IN EN IFX54211 MBV33 OUT 3 +3V3 LEDs P1.1/LED2 P1.0/LED1 LED2 LED1 LED RT/0603 LED RT/0603 For further information and software examples please visit Legal Disclaimer The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. With respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. Power Supply : Debugging Device : Target Device : XMC 2Go-V1 Kit XMC_2Go-V :43:12 Sheet: 1/1 A B C D E XMC 2Go Kit XMC1100 in VQFN24 Figure 5 Schematic of the Board Users Manual 12 Revision 1.0,

13 38.5 mm X101 XMC 2Go Production Data 3.2 Components Placement and Geometry IC201 D101 C201 C202 C104 D102 R107 R109 C106 R106 R105 C101 R101 C103 IC101 C107 LED101 R102 C102 C109R108 C105 Q101 C110R104 C108 R103 C2 C1 IC1 P2 P1 LED2 R2 LED1 R mm Figure 6 Components Placement and Geometry Board Users Manual 13 Revision 1.0,

14 XMC 2Go Production Data 3.3 List of Material The list of material is valid for the Version 1. Table 4 List of Material No. Qty Value Device Reference Designator C1 C2 C101 C102 C nF 50V % X5R CER Capacitor C104 C105 C106 C pF 50V % COG CER Capacitor C109 C uF 10V % X5R CER Capacitor C107 C uF 10V % X7R CER Capacitor C NX3225SA 12MHZ AT-W 3.2X2.5 Crystal, NDK Q R % Resistor R102 R103 R k % Resistor R M % Resistor R R % Resistor R105 R R % Resistor R R % Resistor R1 R2 R LED RT 0603 D 110mcd LSQ976-Z LED red LED1 LED LED GN 0603 D 110mcd LGQ971-Z LED green LED ZX62-AB-5PA Connector, Micro-USB, Hirose X101 Linear Voltage Regulator, Vout = IFX54211 MBV33 SCT V, Infineon IC201 Microcontroller, XMC1100, Cortex XMC1100_VQFN M0, Infineon IC1 Microcontroller, XMC4200, Cortex XMC4200_QFN M4F, Infineon IC BAS3010A-03W SOD323-R Diode, Infineon D ESD8V0L2B-03L TSLP-3-1 TVS Diode, Infineon D PINHD 8x1 0,1" TH Pin Header, 8-pin, 0.1 TH X1 X2 Board Users Manual 14 Revision 1.0,

15 w w w. i n f i n e o n. c o m Published by Infineon Technologies AG

16 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Infineon: KIT_XMC_2GO_XMC1100_V1