How to install shaker motor in a LOTR standard edition
|
|
- Alban Russell
- 6 years ago
- Views:
Transcription
1 How to install shaker motor in a LOTR standard edition What you need: 1. Shaker motor kit Stern Rev. B [ FP ] 2. LOTR v10.02 game ROM chip [ FP-GROM-LOTR v10.02] 3. LOTR shaker PAL chip [ FP-GAL16V8] 4. Shaker motor controller [ FP ] 5. LOTR v10.0 display ROM chip [ FP-DROM-LOTR] (optional) 6. 2 meters of 0,65mm 2 wire 7. Screws, plastic spacers, wire terminal connector and misc. tools Chip installations: 1. Turn off the game with the power switch. 2. Replace the old PAL chip at position U213 with the shaker PAL chip. a. Beware of the positioning of the chip! Check the notch and pin #1 dot carefully! 3. Replace the old game ROM chip at position U210 with the v10.02 game ROM chip. a. Beware of the positioning of the chip! Check the notch carefully! 4. If needed - replace the old display ROM chip at position U5 with the v10.0 display ROM chip. Check the notch carefully! This chip is located on your DMD controller board. 5. Turn on your game. Make sure the game boots up and that everything is working fine. a. If the game doesn't boot up, turn it off, remove your batteries, wait 30 seconds, and try again. Or reseat your game ROM. 6. Turn off the game with the power switch.
2 Shaker installation: 1. Install the shaker motor according to the instructions. Use the installation paper template for positional guidance. a. Make sure that the shaker motor cover will go free from the tilt pendulum so you can easily remove the cover without any hassle!
3 2. Install the interface board that came with the shaker kit. 3. Install the shaker motor controller. a. Use at least two plastic spacers and appropriate screws. b. It is easier to wire the controller before it is installed but make sure that you find a good spot for it first.
4 Wiring the shaker: 1. Locate the upper coin door switch and connect a wire to the top-most terminal via a terminal connector. This is the coin door interrupted 16 Volt AC power to the shaker. 2. This wire shall then be connected to the RED wire going to the 7-pin socket on the interface board. 3. Locate header J9 in the bottom part of the I/O power driver board located in the back box. 4. Press a wire in the empty slot at pin #5. This is the game controlled ground that activates the shaker. Be careful not to damage the connector housing! 5. This wire shall then be connected to the GRAY wire going to the 7-pin socket on the interface board.
5 6. Connect the RED wire coming from the 5-pin socket on the interface board to the Power + pin on the motor controller board. 7. Connect the BLACK wire coming from the 5-pin socket on the interface board to the Power - pin on the motor controller board. 8. Connect the RED wire coming from the shaker motor to the Motor + pin on the motor controller board. 9. Connect the BLACK wire coming from the shaker motor to the Motor - pin on the motor controller board.
6 Checking the installation: 1. Check that everything is installed in a way so it is not interfering with brackets etc. when the playfield is lowered into the game.
7 2. Check, and double check, that everything is wired correctly. 3. Here is a full wiring diagram. Motor controller Shaker motor Red Black Motor + Motor - Power - Power + Red Black 5-pin Interface board 7-pin Red Top terminal 16 Volt AC Gray J9, pin 5 Ground activation Upper coindoor switch I/O power driver board
8 Configuration and running the game 1. There is no in-game configuration that needs attention. 2. Set the motor controller knob to 50% as a base setting. You can later adjust the intensity of the shaker to your liking by turning this knob. 3. Turn on your game and play to enjoy the shakes! Other considerations 1. Random callouts a. Stern released a service bulletin (#157) about upgrading sound software on the Whitestar platforms. If you get random call outs during attract mode, you need a sound update. The ROM can be downloaded from their site. Here is the service bulletin instructions: b. The only caution is that Stern is not very specific about when the process is done. "Wait for LED1 to start flashing continuously (this indicates flash procedure was successful). Note: This usually takes a few minutes." During the upgrade, the LED1 flashes irregularly, providing feedback that the upgrade is in progress. But at one point the LED1 will probably start to flash continuously, but it is fairly slow - perhaps one flash per second. Please be patient! After some time irregular flashes will resumed. When finished, the "continuous flashing" is quite rapid. 2. Missing transistor a. On some late produced standard LOTR games there is a missing transistor at position Q12 on the I/O power driver board. If it is missing a new transistor (STP20N10L) needs to be installed (soldered).
into the EMU E4 Classic and E4 Platinum Samplers
Installing the CF-CARD SCSI Card Reader/Writer Drive into the EMU E4 Classic and E4 Platinum Samplers Thank you for purchasing the CF-CARD Internal Card Reader Drive Installation Kit from SCSICardReaders.com.
More informationButton Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System
Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept
More informationCHAPTER Wi r i n g NOTICE:
CHAPTER Wiring NOTICE: Information in this manual may change without notice. Midway Games West Inc. reserves the right to make improvements in equipment function, design, or components as progress in engineering
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationINSTALLING ColorDMD LED DISPLAY IN BALLY GAMES WITH DISPLAY ON LAMP BOARD
INSTALLING ColorDMD LED DISPLAY IN BALLY GAMES WITH DISPLAY ON LAMP BOARD These instructions are for mounting a ColorDMD LED display in a Bally game that has the display mounted on the swinging backbox
More informationSpace Duel 4 in 1 MultiVector INSTALL GUIDE
Space Duel 4 in 1 MultiVector INSTALL GUIDE The Space Duel 4 in1 MultiVector kit includes four boards, the main board is pictured above and the CPU, Vector & ER2055 boards and cable below. As you can see
More informationFilm-Tech. The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment.
Film-Tech The information contained in this Adobe Acrobat pdf file is provided at your own risk and good judgment. These manuals are designed to facilitate the exchange of information related to cinema
More informationEMC 10T "CE" Mechanical Upgrade Procedure
EMC 10T "CE" Mechanical Upgrade Procedure Kit Part Number: 009866-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationInstallation, Usage and Maintenance Guide for Kit 1
Installation, Usage and Maintenance Guide for Kit 1 July 2013 WARNING Read this document before installing or using Data East/Sega Speaker Light Mod by Pinballtoppers Improper installation, improper use,
More informationColecovision 5v Memory Mod Installation
Colecovision 5v Memory Mod Installation The Colecovision suffers from common failure points: the power supply, power switch, and 4116 DRAM. The power supply suffers from poor soldering, the power switch
More informationWORDSYNC ADDENDUM to the SupraDrive Operator s Manual
WORDSYNC ADDENDUM to the SupraDrive Operator s Manual Congratulations on your purchase of a SupraDrive Hard Card or WordSync Interface Kit for your Amiga 2000 computer. Your new hard drive system will
More informationTwisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation & Service Manual
Twisted Nitro Stunt Racing New Cabinet Design with Sintra Marquee Supplement to Operation & Service Manual Document Part #: 040-0271-01 Rev. C Your cabinet has a new design with a Sintra Marquee, stand-alone
More informationEMC 10/4 "CE" Mechanical Upgrade Procedure
EMC 10/4 "CE" Mechanical Upgrade Procedure Kit Part Number: 009663-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationMAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationTo connect the AC adapter:
Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator
More informationIon Memory Upgrade. Visit the AMI Entertainment Web site PM
Ion Memory Upgrade Visit the AMI Entertainment Web site http://www.meritgames.com PM0672-04 COPYRIGHT 2011 AMI ENTERTAINMENT NETWORK, INC. Ion Memory Upgrade CONTENTS: QTY PART NUMBER DESCRIPTION 1 EC0146-06
More informationPart 2: Building the Controller Board
v3.01, June 2018 1 Part 2: Building the Controller Board Congratulations for making it this far! The controller board uses smaller components than the wing boards, which believe it or not, means that everything
More information*E * E E0606
75000 SERIES B Instrument BASIC Installation Note Copyright Agilent Technologies, Inc., 1990-2006 *E1300-90020* E1300-90020 E0606 Manual Part Number: E1300-90020 Printed: June 2006 Edition 1 Rev 2 Microfiche
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationEVGA assumes you have purchased all necessary parts needed to allow for proper system functionality.
Before You Begin Parts NOT in the Kit This kit contains all the hardware necessary to install and connect your new EVGA e-7050/610i GPU motherboard with integrated GeForce graphics processing. However,
More informationUpgrading a 2U CHP to an i7 Quad Core SBC
Upgrading a 2U CHP to an i7 Quad Core SBC 1. Parts required: i7 SBC Slim line SATA DVD drive Combined SATA data and power cable for slim-line optical drive Serial port ribbon cable - 9way D male to 10
More informationDELUXE STEREO AMPLIFIER KIT
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN SPEAKER DOCK WITH THIS DELUXE STEREO AMPLIFIER KIT Version 2.0 Build Instructions
More informationG80 MULTIGAME/SPEECH/SOUND INSTALL GUIDE
G80 MULTIGAME/SPEECH/SOUND INSTALL GUIDE The G80 MultiGame kit includes the items pictured above. 1. Main PWA 2. Spinner PWA 3. Wire Harness Interface PWA 4. 48 34 conductor ribbon cable 5. 3 pin connector
More informationTreadmill Embedded Touch Screen Won t Power Up
Treadmill Embedded Touch Screen Won t Power Up E-TRe and E-TRxe This document contains the necessary information to troubleshoot a treadmill with an embedded touch screen that will not power up. Follow
More informationIntelliVue MP20/30. Hardware Upgrade Installation Guide. IntelliVue Patient Monitor MP20/30. Patient Monitoring M B *M B*
IntelliVue MP20/30 Hardware Upgrade Installation Guide IntelliVue Patient Monitor MP20/30 Patient Monitoring M8001-9302B *M8001-9302B* Part Number M8001-9302B 4512 610 06841 Printed in Germany 01/05 1
More informationFloppy Disk To USB. Converter Installation and. Operation Manual
Floppy Disk To USB Converter Installation and Operation Manual Kit Price $125.00 Plus Shipping Why Should I Change My Floppy Drive To A USB Drive? You won't ever need floppies anymore and yet you'll be
More informationChapter 2 Working Inside Desktop Computers and Laptops
Chapter 2 Working Inside Desktop Computers and Laptops TRUEFALSE 1. When disassembling a computer, it's okay to stack circuit boards on top of each other as long as you follow ESD protection rules. (A)
More informationFB2550 to FB2558 Upgrade Kit Revision /18
Bulletin 51438 FB2550 to FB2558 Upgrade Kit Revision 1.0 08/18 Desktop, Rack Mount & Panel Mount Enclosures Instructions (34214 kit) 1. Shut down the FB2550 using the F5 key. 2. Once properly shut down,
More informationAdditional information for Octopus NET manual Octopus NET Rack. Additional information for Octopus NET manual. Octopus Net Rack
1 Additional information for Octopus NET manual Octopus Net Rack 2 Table of Contents 1. Classification... 3 2. Delivery Content... 4 3. Expansion... 4 4. Konfigurationsbeispiele:... 4 5. Description oft
More informationWILLIAMS PINBALL SYSTEM 7 DIAGNOSTIC TEST UNIT
WILLIAMS PINBALL SYSTEM 7 DIAGNOSTIC TEST UNIT Copyright 2010-2016 Timothy J. Marsh Page 1 TERMS OF USE: THIS DIAGNOSTIC TOOL INCLUDES SOFTWARE, HARDWARE AND/OR INFORMATION (THE UNIT ) FOR USE BY QUALIFIED
More informationVALCam Laptop Documentation
VALCam Laptop Documentation Introduction Thank you for purchasing the VALCam Laptop, the first image acquisition system designed specifically for photo-id and visual database applications for laptop computers.
More informationMAIN PCB (The small one with the square cut out from one side)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationInstalling System Board Options
CHAPTER 8 Installing System Board Options This section describes how to install the following options: Expansion cards Memory modules Microprocessor This section also includes instructions for replacing
More informationKit K Instructions. V8700 to Alpha Conversion Instructions
V8700 to Alpha Conversion Instructions Contents Contents Installation Instructions for Kit K-00927-0001 Before You Begin..................................................................................
More informationRAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100800 1 Cable Installation Kit 2000901-1 1 Dielectric Grease 2002872
More informationSRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
More informationUpgrading and Servicing Guide
Upgrading and Servicing Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed
More informationSNES / SFC Cartridge to Nintendo Super System Adapter Installation / Instruction Manual
SNES / SFC Cartridge to Nintendo Super System Adapter Installation / Instruction Manual The latest version of this manual can be found at: http://www.projectvb.com/nss Doc. Rev. 1.0 Page 2 of 7 Super System
More informationReplacing the Hardware Configuration Option EPROM on the 1822
MPMS Service Note 1014-806 Replacing the Hardware Configuration Option EPROM on the 1822 When you install an MPMS option, you will use these procedures to replace the hardware configuration option EPROM
More informationK Service Source. Macintosh II/IIx/IIfx
K Service Source Macintosh II/IIx/IIfx K Service Source Basics Macintosh II/IIx/IIfx Basics Overview - 1 Overview This manual includes complete repair procedures for the Macintosh II, Macintosh IIx, and
More informationI/O Expansion Board. Control Made Simple
? Control Made Simple I/O Expansion Board West Coast Office 1263 El Camino Real Menlo Park, CA 94025 Phone (650) 853-1444? Fax (650) 853-1405 www.flashcutcnc.com Midwest Office 444 Lake Cook Road, Suite
More information16MB Sound Flash Installation Instructions for E6400 Ultra, E4XT Ultra & E-Synth Ultra
16MB Installation Instructions for E6400 Ultra, E4XT Ultra & E-Synth Ultra 6876 Use these instructions to install of rewriteable Flash Sound Memory to the E6400 Ultra, E4XT Ultra or the E-Synth Ultra.
More informationThe basic product comes with the IRS5 control board, 3 internal cables, 1 external cable with a 5 volt adapter and a mounting bracket with hardware.
Please read these instructions and watch the Installation Video before you proceed with the installation of the PC-IRS5-01. Installation Video: http://youtu.be/os98e32vhb4 The PC-IRS5-01 Infrared Receiver
More informationInstallation Guide AMM-1525M/1510M/525M. SCSI Audio Host Adapters and Sound Cards
R Installation Guide AMM-1525M/1510M/525M SCSI Audio Host Adapters and Sound Cards 1 Getting Started This document provides the basic information needed to quickly configure and install the Adaptec AMM
More information10. In the world of computers, the term refers to the computer s physical components, such as the monitor, keyboard, motherboard, and hard drive.
Computer Maintenance 2016 Fall Final Review True/False Indicate whether the statement is true or false. 1. A motherboard can have more than one bus, each using a different protocol, speed, data path size,
More informationIQ32 Upgrade Kit Assembly Instructions
IQ32 Upgrade Kit Assembly Instructions Jim Veatch WA2EUJ September 17, 2018 TABLE OF CONTENTS 1. INTRODUCTION... 3 2. IQ-32 UPGRADE KIT INVENTORY... 4 3. PREPARING THE RS-HFIQ AND SIDE PANELS... 6 4. CONNECTING
More informationUzebox JAMMA. Operation manual. (For Uzebox JAMMA Rev. C devices)
Uzebox JAMMA Operation manual (For Uzebox JAMMA Rev. C devices) Basement Hobbies 2011 Contents Warnings 2 Introduction 3 Materials 4 Overview 5 Installation 6 Operation 7 Troubleshooting 13 Contact 16
More informationBackground. About this document. After the upgrade
Table of Contents Background... 3 About this document... 3 After the upgrade... 3 Mounting the Upgrade PCB... 4 Step 1 - Removing the cover... 4 Step 2 - Removing the MSX Audio Bios rom... 4 Step 3 - Remove
More informationCarefully remove the translite from the backbox and then lower the speaker panel to the position shown in Fig. A to gain access to the backbox.
Installation Instructions for Data East (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display
More informationNavigation interface for Jeep GC 5 RA2 NTV-KIT581
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Jeep GC Navigation interface for Jeep GC 5 RA2 NTV-KIT581 NNG-JEEP GC Kit Content 5 1 6 4 7 2 3 1. 2. 3. 4. 5. 6. 7. 8.
More informationColorful Technology Website:
Colorful Technology Website: http://www.colorful.cn Thanks for purchasing our based on Intel B250 Chipset motherboard. The motherboard C.B250A-BTC PLUS V20 based on Intel B250 Express Chipset, support
More informationMP3 audio amplifier. Build Instructions. Issue 2.0
MP3 audio amplifier Build Instructions Issue 2.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit Board (PCB). The components
More informationDell Inspiron N5110 Service Manual
Dell Inspiron N5110 Service Manual Regulatory model: P17F Regulatory type: P17F001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer.
More informationQuicksilver 606 TR-606 CPU Upgrade
Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...
More informationLocal Set Point Module Operating Bulletin
Local Set Point Module Operating Bulletin 1 Notice: The manufacturer reserves the right to make any changes and improvements to the products described in this manual at any time and without notice. This
More informationHolland Computers, Inc. Crane Kit Manual Part Number RA-CRANE-KIT
Holland Computers, Inc. Crane Kit Manual Part Number RA-CRANE-KIT SECTION 1 - Introduction Description This kit has been manufactured as a replacement gantry and electronics for existing machines using
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationAg Leader Technology Insight. Direct Command Installation Spra-Coupe 7000 Series
Note: Indented items indicate parts included in an assembly listed above. Part Name / Description Part Number Quantity Direct Command Spra-Coupe 7000 Kit 4100531 1 Liquid Product Control Module 4000394
More informationValidator Update Instructions for Rowe BC1200 $1 - $20
Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit
More informationHD22 and HD30 Service Parts
HD and HD0 Service Parts This is the list of service parts and wiring diagrams for all versions of these two hotel dispensers. Pay close attention to the voltage and/or cycles to be sure of ordering the
More informationrevolution How does the ibutton work? Full kit including PCB, PICAXE-08M chip and ibutton key. Spare ibutton Key
AXE109S LOG020 Full kit including PCB, PICAXE-08M chip and ibutton key. Spare ibutton Key The ibutton is an electronic chip armoured in a 16mm stainless steel can. Because of this unique, durable package,
More informationMacBook Pro 13" Retina Display Mid 2014 Display Assembly Replacement
MacBook Pro 13" Retina Display Mid 2014 Display Assembly Replacement Replace the Display Assembly in your MacBook Pro 13" Retina Display Mid 2014. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com
More informationChapter 3: Computer Assembly
Chapter 3: Computer Assembly IT Essentials v6.0 ITE v6.0 1 Chapter 3 - Sections & Objectives 3.1 Assemble the Computer Build a Computer. 3.2 Boot the Computer Explain how to verify BIOS and UEFI settings.
More informationSmart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction
Smart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction Electronics Module (Part number 51404208 503, -513) Document Form: 34-SM-33-01 Effective: 09-01 Supersedes: 34-SM-33-01,
More informationAttention: The connectors on the BMD16N are not normal network plugs. Never connect the decoder to a PC or any other network device!
BMD16N version 1.2 Feedback decoder with 16 contacts for the S88-bus Compatible with a.o. Märklin Digital, Uhlenbrock Intellibox, Fleischmann Twin-Center and LDT HSI-88 Compatible with the s88-n standard
More informationShack Clock kit. U3S Rev 2 PCB 1. Introduction
Shack Clock kit U3S Rev 2 PCB 1. Introduction Thank you for purchasing the QRP Labs Shack Clock kit. This clock uses the Ultimate3S QRSS/WSPR kit hardware, but a different firmware version. It can be used
More informationDell XPS L702X Service Manual
Dell XPS L702X Service Manual Regulatory model: P09E series Regulatory type: P09E002 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer.
More informationInstalling TEAC CD-ROM Drives
D I G I T A L Installing TEAC CD-ROM Drives S O U N D Date: May 12, 2000 (updated) Document # TN-E211 We have used only two manufacturers of CD-ROM drives: Toshiba and TEAC. This procedure is to be used
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationPCS-2. Universal Infrared Remote PC Power Switch
PCS-2 Universal Infrared Remote PC Power Switch General Description The PCS-2 allows you to switch your PC / HTPC on-off with your existing TV or universal infrared (IR) remote. Single button mode allows
More informationCarefully remove the translite from the backbox and then swing speaker panel to the open position as shown in Fig. A to gain access to the DMD.
Installation Instructions for SEGA (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display graphics
More information17-Bit Digitizer Board Replacement and Use
MPMS Service Note 1014-812 17-Bit Digitizer Board Replacement and Use This service note explains how to replace the 17-Bit Digitizer board (rev. K0 and higher) that is used in the MPMS and MPMS-XL. All
More informationUpgrading and Servicing Guide
Upgrading and Servicing Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed
More informationDirectCommand Installation RoGator 864/874/1064/1074 (MY 2006 & Earlier) Ag Leader Technology
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100524 1 Generic Cable Installation Kit 2000901-1 1 Hardware Kit
More informationTROUBLESHOOTING CHAPTER
CHAPTER TROUBLESHOOTING CAUTION: Turn AC power off before attempting any of the following procedures, unless otherwise specified. Failure to do so may damage equipment, cause personal injury, or void warranty.
More informationOpen Desktop WorkStation System Components Items Labeled in RED are ESD Sensitive
Page 1 of 21 Open Desktop WorkStation System Components Items Labeled in RED are ESD Sensitive Back Plane Pegasos IDE Cable Hard Drive Video Card G4 CPU IDE Cable CDROM Page 2 of 21 Remove top of case
More informationK8099 NIXIE CLOCK. * optional enclosure TKOK19 (black) - TKOK17 (white) ** optional plexiglass enlcosure B8099 ILLUSTRATED ASSEMBLY MANUAL
Total solder points: 230 + 74 Difficulty level: beginner 1 2 3 4 5 advanced NIXIE CLOCK K8099 ** * A unique combination of both vintage and modern electronics ILLUSTRATED ASSEMBLY MANUAL H8099IP-1 * optional
More informationGrace Digital Mondo LCD Replacement & Part #s
Grace Digital Mondo LCD Replacement & Part #s How to remove the Display Assembly also - Part Numbers. Written By: Seby ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION This is to replace an LCD
More informationInstallation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2
1 Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 Tsubis Part Number: LCD12-0046 Power Down 1. Power down the controller. 2. Power down the complete machine by turning off the rear
More informationInstalling the PSU for the S50 and S50N
Installing the PSU for the S50 and S50N Caution: Use only the power cords supplied with the power supply. Do not supply power to your S50 or S50N system until the power supply and modules have been installed.
More informationInsert Replacement Manuel. Overall Image. FEBO (HK) INTERNATIONAL LIMITED Page 1. Item 28 Electrical Insert Store VCF
Overall Image B A A A C D A E FEBO (HK) INTERNATIONAL LIMITED Page 1 Insert Replacement Manuel Item 28 Electrical Insert Store VCF SKU# 08IN-28-2A Color Black Fireplaces A. Mother Board B. Transformer
More informationAir Hockey v7.0 Controller PCB Air Hockey 10v Transformer
KNOWN ISSUES SORTED BY BOARD REVISION DYNAMO HOCKEY PCBs LISTED IN THIS WORKSHEET are no longer available for purchase or serviced by the manufacturer. Most tables can be upgraded to Dynamo s latest v7.0
More informationUpgrading and Servicing Guide
Upgrading and Servicing Guide The information in this document is subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not
More informationHarbortronics Time-Lapse Package Troubleshooting Guide This document is intended to help diagnose any problems with your Time-Lapse Package.
This document is intended to help diagnose any problems with your Time-Lapse Package. Power Everything in the Time-Lapse Package (TLP) is powered by the large Lithium-Ion Polymer battery pack, made specifically
More informationIFC-1010/2020 EPROM Replacement
Installation Instructions Issue Date 11/19/01 IFC-1010/2020 Replacement System Power Sources IMPORTANT: Always remove primary and secondary power before working on the system. Use the following procedure
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationDSP-232 Upgrade Kit A.06113
DSP-232 Upgrade Kit A.063 Installation and Operation Manual Rev. 2.0 WARRANTY WHO IS COVERED WHAT WE WILL DO WHAT YOU MUST DO WHAT IS NOT COVERED SERVICE WARRANTY HOW TO CONTACT TIMEWAVE TIMEWAVE TECHNOLOGY
More informationEmax SE SCSI Port Emax Plus Retrofit Instructions (Fl360)
Emax SE SCSI Port Emax Plus Retrofit Instructions (Fl360) Tools needed: Exacto Knife, Vacuum Desoldering Tool, Soldering Iron, Solder, Phillips Screwdriver, Needle Nose Pliers, 1/2 Nut Driver, 5/8 and
More informationEQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.
EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationDell XPS M1530 Service Manual
Dell XPS M1530 Service Manual Model PP28L www.dell.com support.dell.com Notes, Notices, and Cautions NOTE: A NOTE indicates important information that helps you make better use of your computer. NOTICE:
More informationNote: Indented items indicate parts included in an assembly listed above
Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number QTY DirectCommand Kit 4100869 1 Installation Instructions 2006318 1 DC Motor Driver 4002736 1
More informationZX81 ULA Replacement. Installing the ULA
ZX81 ULA Replacement The ZX81 ULA replacement is a plug in pin compatible clone of the original ZX81 ULA with a bit of an extra boost. Installing the ULA The replacement ula includes circuitry to directly
More informationSL-35 MARK III INSTRUCTION MANUAL
SL-35 MARK III INSTRUCTION MANUAL INTRODUCTION The SL-35 Mark III camera is built specifically as a lightweight 35mm Motion Picture Camera. Weighing less than 2.4 kg this new camera is ideal for Steadicam,
More informationRAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt
DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100852 1 Cable Installation
More informationRevision History E F G H J K Revision Description: K > Allegion Rebranding.
Notes: Enter any notes here. These notes must include: how many sides of the paper are printed ink color (usually black, may also be one or two specific colors, such as a Pantone value, or 17.000 8.500
More informationJanuary Bob Wright. 1 P age Bob Wright
The upgrade is completed using the 401 control board and three Step1 driver boards supplied as a kit by Conqueror Design and Engineering Ltd. The kit includes all cable terminators for connections to the
More informationE-MU PN FI10993 Rev. B
E-MU PN FI10993 Rev. B Overview Sound Authoring is the process of creating sound sets for the Proteus 2000 sound modules, Proteus 1000 sound modules, Proteus Command Stations or Proteus Keyboards. (In
More informationDwarf Boards. DB021 : L298 dual motor driver
Dwarf Boards DB021 : L298 dual motor driver (c) Van Ooijen Technische Informatica version 1.0 PICmicro, In-Circuit Serial Programming and ICSP are registerd trademarks of Microchip Technology Inc. Introduction
More information