Installation Instructions

Transcription

1 HT1006 Series Electric Strike Product Components Electric Strike Body Trim Enhancer (with screws) Keeper Latchbolt Monitor Keeper Shims (2, with screws) ELECTRICAL RATINGS Average Amp: 0.5 Average Amp: to +24 (+/-10%) Volts DC Seated Unseated MINIMUM WIRE GAUGE REQUIREMENTS 200 feet or less feet feet Solenoid Voltage 24 VDC 12 VDC 18 gauge 18 gauge 18 gauge 16 gauge 16 gauge 14 gauge FIVE YEAR LIMITED WARRANTY For any questions regarding this information, call HES Customer Support at N. 17th Ave. Phoenix, AZ For UL Listed applications, the unit shall be connected to a UL Listed Class 2 power supply or a UL 294 Listed control unit. ASSA ABLOY, the global leader in door opening solutions

2 2 Hi-O Overview ASSA ABLOY s standard-based Hi-O system Highly Intelligent Opening connects electronic door components together over a CAN (Controller Area Network) data network, allowing them to communicate and monitor the health of the opening. Intelligence is built into each device instead of one centralized logic unit, creating a plug-and-play system. Each device is instantly recognized when plugged into the system similar to what happens when a USB device is plugged into a computer. Every unit is connected with a four-wire cable and has ElectroLynx plug-in connectors for quick installation. Hi-O is based on devices with built-in intelligence and a CANbus that links all the devices together. Data traffic on the Hi-O CANbus can be encrypted. Each Hi-O device (such as a push plate, electric strike, card reader, door operator, etc.) is connected to the CANbus through a single, four-wire cable. Two of the wires supply power and the other two are used for data communication. Refer to the Hi-O Systems Manual (A8002). Prepare Strike 1. Evaluate opening and reset Dip Switch if needed (see Adjustment Instructions on page 4). 2. For available faceplate options, see page 9. Prepare Frame 1. Prepare frame using the appropriate template for your lockset and faceplate combination (see page 8). 2. Connect to system using electrolynx connectors (see page 3). 3. Install the HT1006 strike body into the door frame. 4. Set up the Hi-O system (see pages 5-7).

3 3 Prepare Strike Wiring The HT1006 series drawing below show the Hi-O application Voltage: 12-24VDC (11-28VDC range) operation Filtered and Regulated Power Supply Current:.5 Amp Seated.04 Amp Unseated A. Electrolynx Connectors PIN 2 Red ( VDC) PIN 4 PIN 6 PIN 8 PIN 7 Brown (CANbus ) PIN 5 PIN 3 White (CANbus ) PIN 1 Black (0 VDC) NOTE: For HT1006 (On the 8-Pin Connector): PIN 2 Red (Power VDC) PIN 1 Black [Power 0 VDC/Common(-)] PIN 3 White CAN bus HIGH PIN 7 Brown CAN bus LOW B. Electrolynx Connector System Notes The System is designed to be installation friendly with quick connectors. The total length of the bus should not be more then 50 meters (164 feet) and stub (star) connections should not be more then 10 meters (33 feet). The optimal solution places the door controller close to the door to keep cable lengths to a minimum. IMPORTANT: ElectroLynx connectors plug and lock together in only one way, as shown. Do NOT force connectors together.

4 4 Adjustment Instructions The default factory settings will be used in almost every application. They are: Group 1 Terminator OFF NOTE: In some situations (such as mantraps) the default factory settings must be chaged. Refer to the Hi-O Systems Manual (A8002) for additional information. If so, follow the procedure below to change the DIP switch settings before installing strike IMPORTANT: Ensure that the serial number of the unit is retained. Once the device is locked and encryption enabled, access to the device requires the serial number. If the serial number is lost, the device must be returned to the factory to be reset. A. To change the settings carefully peel off the white label located on the floor of the HT1006 to access the DIP switch. Set the label aside. Using a small tool adjust the DIP switches as described below. Then replace the white label. Unit with protective label. DIP switch location. Serial number placement. B. SWITCH 1: Set the manual group switch. Default is OFF and is appropriate for most applications. Most installations use Group 1 only. Switch 1 OFF = membership in Group 1. Switch 1 ON = membership in Group 2. C. SWITCH 2: Set the termination resistor (Default is OFF). In a Hi-O CANbus network, it is necessary to terminate the communication bus to avoid interference. Termination should take place in Activators, for example in a card reader, opening button, or a gateway. Switch 2 OFF removes the 120 ohm connection between CAN-Low and CAN-High. Switch 2 ON terminates a 120 ohm resistor between CAN-Low and CAN-High. Use only one termination resistor per application. Refer to the Hi-O Systems Manual (A8002) for additional information. ON 1 2 Orientation: When you hold the strike with the switch oriented towards the top of the device, the switch position ON is at towards the TOP of the device.

5 5 Hi-O System Software Step 3 Step 4 Step 5 Step 6 Step 1: Install hardware according to installation instructions and the Hi-O System Manual. Step 2: Download and install the latest release of Hi-O Manager and Logger software, and DDF files according to the Hi-O System Manual. Step 3: Open Hi-O Manager and click the Next button to determine what devices are attached to the system. Step 4: Icons representing system appear in the left pane. Step 5: Click the Push Button icon. Step 6: In the Properties tab of the right pane, click the Advanced Properties arrow to view the Properties pane. Step 7: In the Property Group pane, set security locking and timers, and set the values that will generate system messages. In the Property Group menu, select from the following: Information Read-only information from the device. Device Offline Behavior Set unlock, delay and egress timing for Lock. Voltage Out of Range Limits Set low and high thresholds for voltage. When thresholds are exceeded system messages will be generated. Jam Timers Set time to dictate when a jam message is sent when the strike is locked and keeper open. Transmit Command Validation Set the above Locking, Security Locking, Opening, Holding, Activator State, and System Voltage to valid or invalid. Refer to the Hi-O System Manual (A8002) for additional information.

6 6 Hi-O Systems Settings Select the Properties tab. Click the Push Button icon in the view pane. Click the Advance Properties arrow to expand the menu. Choose from the Properties Groups list: Information Device Offline Behavior Voltage Out of Range Limits Jam Timers Transmit Command Validation Information Displays read-only general information from the device, including: Serial Number Node ID Host Node ID Product Class Application Name (Model Number) Hardware Version Hi-O Stack Version Hardware Group ACP Active (Address Claiming Process)

7 7 Hi-O System Settings Device Offline Behavior Device Offline Behavior No Change Lock Unlock Voltage Out of Range Limits Jam Timers Transmit Command Validation Set Voltage Out of Range Limits Establishes Out of Range entries in Log. Low Overflow Voltage in Volts High Overflow Voltage in Volts 11 to 28 is the normal range. Set Jam Timers Set time to dictate when a jam message is sent when the strike is locked and keeper open. Jam Delay Timer in seconds (0 255) Set Transmit Command Validation Sets Locking, Security Locking, Opening, Holding, Activator State, and System Voltage entries to valid or invalid, determining if the entries are read or ignored. NOTE: If it is not possible to set respective entries, check to see if they are set to valid. Refer to the Hi-O System Manual (A8002) for additional information

8 7 Hi-O System Settings Device Offline Behavior Device Offline Behavior No Change Lock Unlock Voltage Out of Range Limits Jam Timers Transmit Command Validation Set Voltage Out of Range Limits Establishes Out of Range entries in Log. Low Overflow Voltage in Volts High Overflow Voltage in Volts 11 to 28 is the normal range. Set Jam Timers Set time to dictate when a jam message is sent when the strike is locked and keeper open. Jam Delay Timer in seconds (0 255) Set Transmit Command Validation Sets Locking, Security Locking, Opening, Holding, Activator State, and System Voltage entries to valid or invalid, determining if the entries are read or ignored. NOTE: If it is not possible to set respective entries, check to see if they are set to valid. Refer to the Hi-O System Manual (A8002) for additional information

9 Cutout Templates 8 Inches [mm] HT1006 WITH MORTISE LOCKSETS HT1006 WITH CYLINDRICAL LOCKSETS Please note the horizontal centerline of the electric strike in relation to the centerline of the mortise lockset. Please note the horizontal centerline of the electric strike in relation to the centerline of the cylindrical lockset. Mortise Lockset Vertical Centerline Strike Prep Cylindrical Lock Vertical Centerline Strike Prep 8" [203.2] 4" [101.6] Strike Lock 3/8" [9.53] 3-1/2" 4-1/8" 4-7/8" 2-1/4" [88.9] [104.77] [123.83] [57.15] STRIKE LOCK 3-1/2" 4-1/8" 4-7/8" [88.9] [104.77] [123.83] 1-3/4" [44.45] 5/8" [15.88] 1-3/4" [44.45] 5/8" [15.88] METAL JAMB INSTALLATION FOR 1006 SERIES FACEPLATES Cutout dimenstions for option faceplates: J, K, KM, N, NM, Z METAL JAMB INSTALLATION FOR D SERIES FACEPLATES Cutout dimenstions for option faceplates: KD, ND WOOD JAMB INSTALLATION FOR SERIES FACEPLATES Cutout dimenstions for option faceplates: J2, K2, KM2, N2, 3-3/8" [85.72] 4-7/8" [123.83] 4-1/8" [104.77] 29/32 [23.01] 3-3/8" [85.72] 19/32 [15.08] 5/32 4-7/8" 4-1/8" [123.83] [104.77] 3-3/8" [85.72] 9" [228.6] 1-11/16" [42.86] 2X UNC THREADS 1-11/16" [42.86] 2X UNC THREADS 1-11/16" [42.86] 1-3/8" [34.92]

10 Faceplate Options (4-7/8 x 1-1/4 SQUARE CORNER) 9 C L = center line of faceplate (2nd line = center line of faceplate opening) Inches [mm] ND OPTION FACEPLATE N OPTION FACEPLATE NM OPTION FACEPLATE Inches [mm] 5/32 [3.97] 3-1/8 [79.37] 3-1/8 [79.37] 1/8 [3.17] 2-7/8 [73.02] 23/32 [18.26] 7/8 [22.23] 1-9/64 [28.83] KD OPTION FACEPLATE K OPTION FACEPLATE KM OPTION FACEPLATE 1-1/16 [26.72] 1-11/32 [34.11] 29/32 [23.39] 1-11/32 [34.11] 19/32 [15.46] 1-15/32 [37.29] 23/32 [18.22] 27/32 [21.46] 1-3/32 [27.81] Z OPTION FACEPLATE J OPTION FACEPLATE The HT1006 is not recommended for A, AD, AM, A-2, E, H, HD, HM, HT, HTD, H-2, R, T, TD, T-2 options. 5/16 [7.79] 1-15/32 [37.29] 1-23/32 [43.64] 1-25/64 [35.48] 1-37/64 [40.08]

11 HT1006 ELECTRIC STRIKE INSTALLATION INSTRUCTIONS rev A 2009 HES Inc.