MLM 104 Faceplates Installation Guide

Transcription

1 MLM 04 Faceplates Installation Guide MLM 04 Faceplates This guide provides instructions for installing the following Extron MediaLink Mounting Options faceplates, which are designed for use with MLC 04 IP Plus MediaLink Controllers. The MLM 04 L, MLM 04 GWP, or MLM 04 4GWP faceplate is shipped with the MLC 04 IP Plus controller, depending on the controller configuration that is ordered. The rest of the mounting options described below may be ordered separately as replacements, or for use with an MLC 04 IP Plus that is ordered without a faceplate. MLM 04 L A low-profile, 3.5" H x 6.50" W (8.0 cm H x 6.5 cm W) lectern/furniture-mounting faceplate. This faceplate is required when you are mounting an MLC 04 IP Plus using an optional UCM RAAP or UCM 0X8P mounting kit. Part numbers: (black), (white), (RAL900 white) MLM 04 LAAP A low-profile, 3.5" H x 0.00" W (8.0 cm H x 5.40 cm W) lectern/furniture-mounting faceplate with an opening that accommodates four single-space AAPs Part numbers: (black), (white), (RAL900 white) , Rev. D 08 07

2 MLM 04 Faceplates Installation Guide, cont d MLM 04 GWP A two-gang (4.50" H x 4.60" W [.43 cm H x.68 cm W]) faceplate that can be mounted to a mud ring (mounting bracket), an Extron Surface Mount Box, an Extron External Wall Box, or a standard electrical box Part numbers: (black), (white), (RAL900 white) MLM 04 4GWP A four-gang (4.50" H x 8.3" W [.43 cm H x 0.9 cm W]) faceplate with an opening that accommodates four single-space AAPs. It can be mounted to a mud ring, an Extron Surface Mount Box, an Extron External Wall Box, or a standard electrical box. Part numbers: (black), (white), (RAL900 white) MLM 04 6GWP A six-gang (4.50" H x.75" W [.43 cm H x 9.85 cm W]) faceplate with two openings that accommodate four single-space AAPs each (eight AAPs total). It can be mounted to a mud ring, an Extron Surface Mount Box, an Extron External Wall Box, or a standard electrical box. Part numbers: (black), (white), (RAL900 white)

3 Replacing the MLC 04 IP Plus Faceplate with an MLM Faceplate. If your MLC controller is already installed in a wall or furniture, remove the four screws that attach it to its mounting surface (marked a in the diagram below), and lift it out.. After the MLC has been removed from the wall or furniture, use a small Phillips screwdriver to remove the four faceplate attachment screws (marked b in the diagram below), and save them for later use. CAUTION Do not remove the four faceplate screws while the MLC is installed in a wall or furniture, or the controller may fall into the wall or furniture. DISPLAY ON OFF VCR VOLUME DVD PC 3 CONFIG 4 MLC 04 IP PLUS 3. Lift the faceplate off the MLC 04 IP Plus, as shown below. ON OFF VCR DVD PC ON OFF DISPLAY 3 VOLUME CONFIG MLC 04 IP PLUS 4 Extron 3

4 MLM 04 Faceplates Installation Guide, cont d 4. Align the openings in the new MLM faceplate with the controller s buttons, knob, and LEDs, then place the new faceplate on the MLC 04 IP Plus. 5. Replace the four screws removed in step, and hand tighten them. 6. Install the MLC 04 IP Plus controller in a wall or furniture as appropriate. Templates Use one of the following templates as a guide to measure and mark the hole for installing the MLM 04 faceplate with an attached MLC 04 IP Plus. (Refer to your MLC 04 IP User s Manual for instructions on preparing the mounting site.) CAUTION These templates are not to scale. Use the dimensions shown in the templates as reference guidelines for measuring and drawing the rectangle that will be cut out. The MLC controller requires a depth of at least.0" (5. cm) inside the wall or furniture. 4

5 MLM 04 L and MLC 04 IP Plus L template 3.5" (8.0 cm) Top Panel.8" (7. cm) 6.5" (6.5 cm) 3.5" (8.9 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT Location of MLC 04 IP Plus To install MLC 04 IP Plus and MLM 04 L directly into furniture, cut along this line..50" (0.64 cm).95" (0.75 cm) TEMPLATE IS NOT FULL SIZE. Cut-Out Template for Extron's MLM 04 L and MLC 04 IP Plus L 5

6 MLM 04 Faceplates Installation Guide, cont d MLM 04 LAAP template 3.5" (8.0 cm).8" (7. cm) Top Panel 0" (5.4 cm) 7.9" (0. cm) Location of MLC 04 IP Plus SURFACE CUT-OUT AREA FOR FURNITURE MOUNT To install the MLC 04 IP Plus and the MLM 04 LAAP directly into furniture, cut along this line..50" (0.64 cm).95" (0.75 cm) TEMPLATE IS NOT FULL SIZE. Cut-Out Template for Extron's MLM 04 LAAP 6

7 MLM 04 GWP and MLC 04 IP Plus template 4.5" (.4 cm) Top Panel.8" (7. cm) 4.6" (.7 cm) 3.5" (8.9 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT Location of MLC 04 IP Plus To install MLC 04 IP Plus and MLM 04 GWP directly into furniture, cut along this line. TEMPLATE IS NOT FULL SIZE. Cut-Out Template for Extron's MLM 04 GWP and MLC 04 IP Plus 7

8 MLM 04 Faceplates Installation Guide, cont d MLM 04 4GWP and MLC 04 IP Plus AAP template 4.5" (.4 cm).8" (7. cm) Top Panel 8.3" (0.9 cm) 7." (8.0 cm) Location of MLC 04 IP Plus SURFACE CUT-OUT AREA FOR FURNITURE MOUNT To install the MLC 04 IP Plus and the MLM 04 4GWP directly into furniture, cut along this line. TEMPLATE IS NOT FULL SIZE. Cut-Out Template for Extron's MLM 04 4GWP and MLC 04 IP Plus AAP 8

9 MLM 04 6GWP template 4.5" (.4 cm).8" (7. cm) Top Panel.75" (9.85 cm) Location of MLC 04 IP Plus.0" (7.9 cm) SURFACE CUT-OUT AREA FOR FURNITURE MOUNT To install the MLC 04 IP Plus and the MLM 04 6GWP directly into furniture, cut along this line. TEMPLATE IS NOT FULL SIZE. Cut-Out Template for Extron's MLM 04 6GWP 9

10 Extron Electronics, USA 30 South Lewis Street Anaheim, CA FAX Extron Electronics, Europe Beeldschermweg 6C 38 AH Amersfoort, The Netherlands FAX Extron Electronics, Asia 35 Joo Seng Rd. #04-0 PM Industrial Bldg., Singapore FAX Extron Electronics, Japan Kyodo Building, 6 Ichibancho Chiyoda-ku, Tokyo Japan FAX Extron Electronics. All rights reserved.