System family AR. Transponder-coded safety switch CET.-AR- With guard locking

Transcription

1 System family R Transponder-coded safety switch CET.-R- With guard locking Cat. 4 PLe Safety switch with guard locking Locking force up to 600 N etal housing Diagnostics via 4 LEDs Notice The device is only allowed to be operated in conjunction with the actuator CET--. Details pproach direction Head can be rotated in 90 -steps vailable coding options nicode evaluation ulticode evaluation Category according to EN ISO The category is dependent on the installation position: Installation position Category/PL Cat. 3 PLe Cat. 4 PLe Guard locking types CET1 Closed-circuit current principle Guard locking by spring force. Release by applying voltage to the guard locking solenoid. CET2 Open-circuit current principle Guard locking by solenoid force. ctivation of the guard locking by applying voltage to the guard locking solenoid. CET3 Function as for CET1-R, but here the door position is also monitored. the door monitoring output OT D is set to HIGH as soon as the actuator is above the extended plunger (state: door closed, guard locking not active). The output OT D remains set also with guard locking active. CET4 Function as for CET2-R, but here the door position is also monitored. the door monitoring output OT D is set to HIGH as soon as the actuator is above the extended plunger (state: door closed, guard locking not active). The output OT D remains set also with guard locking active. uxiliary release Included with all versions as standard. Escape release (optional) Some devices have an escape release (see ordering table). Wire front release (optional) The wire front release permits remote release of the guard locking via a pull wire. Flexible routing of the pull wire permits release of the guard locking in inaccessible installation situations. Teach-in input (optional) Some devices with unicode evaluation have a teach-in input. These devices can only be taughtin by switching the teach-in input. In this way the protection against tampering is additionally increased. Lockout bar (optional) The lockout bar can be used to prevent maintenance personnel from being unintentionally locked in the danger area, for example. In locked position, the lockout bar prevents activation of guard locking. The lockout bar can be secured in locked position with up to three locks. Double ramp Versions with double ramp can be approached from two sides. Devices with double ramp are also suitable for applications in which the switch must be "passed over". E.g. on doors that can be opened inwards and outwards. The double ramp can be retrofitted (see accessories page 113). Feedback loop (optional) Versions with feedback loop permit monitoring of connected devices (e.g. contactors). dditionally, a start button can be integrated. LED indicator STTE Status DI Diagnostics LED 1 red See wiring diagram LED 2 green See wiring diagram dditional connections OT onitoring output (semiconductor) OT D Door monitoring output (only CET3/4) RST Reset input Further information Dimension drawings see p. 78 ccessories and spare parts see p. 77 For detailed information, enter the order number You will find information on the series connection of R device on page. 72 Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

2 Ordering table CET.-R- -SG- with 2 plug connectors 12, without door monitoring 8 Order No./item Coding = unicode = multicode Ramp Teach-in input Feedback loop Escape release Wire front release (L1) 1) Lockout bar For wiring diagram see page 80 CET1 Closed-circuit current principle CET1-R-CD-H-0X-SG CET1-R-CR-H-0-SG mm CET1-R-CR-H-0F-SG mm CET1-R-CR-H-0F-SG-C mm CET1-R-CR-H-0S-SG CET1-R-CR-H-0X-SG CET1-R-CR-H-0X-SG-C CET1-R-CR-H-0S-SG-C CET1-R-CR-CH-0F-SG CET1-R-CR-CH-0S-SG CET1-R-CR-CH-0X-SG m 7 mm For detailed information, enter the order number CET1-R-CR-CH-0X-SG-C m B CET1-R-CD-CH-0X-SG CET1-R-CR-CH-0F-SG-C CET2 Open-circuit current principle CET2-R-CR-H-0S-SG CET2-R-CR-H-0X-SG CET2-R-CR-CH-0F-SG-C CET2-R-CR-CH-0X-SG mm 10 mm 1) L1 = sleeve length; cable length = L1 + 1 m. Important: Handle must be ordered separately (see accessories page 112). Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 73

3 System family R CET.-R- -SG- with 2 plug connectors 12, with door monitoring output 8 Order No./item Coding = unicode = multicode Ramp Teach-in input Feedback loop Escape release Wire front release (L1) 1) Lockout bar For wiring diagram see page 80 CET3 Closed-circuit current principle CET3-R-CR-CH-0X-SG-C m CET3-R-CR-CH-0F-SG-C CET3-R-CR-CH-0X-SG CET3-R-CR-CH-0F-SG CET3-R-CR-H-0X-SG CET3-R-CR-H-0X-SG-C CET3-R-CR-H-0X-SG-C CET3-R-CR-H-0F-SG CET3-R-CR-H-0F-SG-C CET3-R-CR-CH-0F-SG-C CET3-R-CR-CH-0S-SG CET3-R-CR-CH-0F-SG-C CET3-R-CD-CH-0F-SG mm 3 m 7 mm 3 m 7 mm 7 mm 7 mm 10 mm B C For detailed information, enter the order number CET4 Open-circuit current principle CET4-R-CR-H-0X-SG CET4-R-CR-H-0X-SG-C m CET4-R-CR-H-0X-SG-C CET4-R-CR-CH-0X-SG CET4-R-CR-CH-0X-SG-C CET4-R-CR-CH-0F-SG CET4-R-CR-CH-0S-SG mm C CET4-R-CD-CH-0X-SG CET4-R-CR-CH-0X-SG-C D 1) L1 = sleeve length; cable length = L1 + 1 m. Important: Handle must be ordered separately (see accessories page 112). 74 Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

4 CET.-R- -SH- with plug connector RC18 23 (no L approval), without door monitoring output Order No./item Coding = unicode = multicode Ramp Teach-in input Feedback loop Escape release Wire front release (L1) 1) Lockout bar For wiring diagram see page 81 CET1 Closed-circuit current principle CET1-R-CR-H-0X-SH CET1-R-CR-H-0X-SH-C CET1-R-CR-H-0F-SH-C CET1-R-CR-H-0F-SH-C CET1-R-CR-CH-0X-SH CET1-R-CD-CH-0X-SH-1132 CET2 Open-circuit current principle CET2-R-CR-H-0X-SH CET2-R-CD-H-0X-SH CET2-R-CR-CH-0X-SH m 10 mm 3 m 10 mm 1) L1 = sleeve length; cable length = L1 + 1 m. Important: Handle must be ordered separately (see accessories page 112). E E For detailed information, enter the order number Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 7

5 System family R CET.-R- -SH- with plug connector 23 (no L approval), with door monitoring output Order No./item Coding = unicode = multicode Ramp Teach-in input Feedback loop Escape release Wire front release (L1) 1) Lockout bar For wiring diagram see page 81 CET3 Closed-circuit current principle CET3-R-CR-H-0X-SH CET3-R-CR-H-0F-SH-C CET3-R-CR-H-0X-SH-C CET3-R-CR-H-0F-SH-C CET3-R-CR-H-0X-SH-C CET3-R-CR-H-0X-SH-C CET3-R-CR-H-0F-SH-C CET3-R-CR-H-0F-SH CET3-R-CR-H-0X-SH-C CET3-R-CR-H-0F-SH-C CET3-R-CR-CH-0X-SH CET3-R-CD-H-0F-SH CET4 Open-circuit current principle CET4-R-CR-H-0X-SH CET4-R-CR-H-0F-SH CET4-R-CR-CH-0X-SH mm 3 m 10 mm 3 m m 7 mm 7 mm 10 mm 7 mm 7 mm 1) L1 = sleeve length; cable length = L1 + 1 m. Important: Handle must be ordered separately (see accessories page 112). E E For detailed information, enter the order number ctuator Series Design Order No./item CES--BWK-0X CET--BWK-0X For detailed information, enter the order number the search box at 76 Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

6 ccessories Type Version Connection cable with plug connectors 12 8 Page 93 Page 9 Connection cable with plug connectors Page 99/100 Connection material Female plug (for self-assembly) Page 101 Strapg plug/y-distributor 12 Page 96 Passive distribution module 12 Page 97 Bolts Bolts for housing design CET Page 107 Fixing material ounting plates Page 110 Safety screws Page 112 Lockout bar echanical key release iscellaneous accessories Emergency unlocking Cover Page 112 Double ramp Handle for wire front release Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 77

7 System family R Dimension drawing With 2 plug connectors LED 2 LED 1 13,4 STTE DI uxiliary release 1 ±4 mm 74, 28 67,2 CET.-.-CR ,6 2 <1> 11 Order actuator CET--BWK-0X separately CET.-.-CD For 6 screw DIN 1207/ISO 4762 X2 () X1 () 4 8 With angle connectors Plunger with read head 10, 26, 23 With plug connector , 78 Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

8 With escape release With lockout bar Basic position for escape release Release by pressing Ø 9, 1,2 60, With wire front release 10 30, 83 Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 79

9 System family R 8 Terminal assignment D Wiring diagram to D Pin Designation Function B C D X 1.1 IB Enable input for channel 2 X 1.2 B Operating voltage R electronics, DC 24 V X 1.3 O Safety output, channel 1 X 1.4 OB Safety output, channel 2 X 1. OT onitoring output X 1.6 I Enable input for channel 1 X V B Operating voltage R electronics, DC 0 V X 1.8 RST Reset input X V C Operating voltage guard locking solenoid, DC 0 V X 2.2 X 2.3 LED 1 LED 1 red, freely configurable, DC 24 V LED 1 red, solenoid energized OT D Door monitoring output LED 1 LED 1 red, freely configurable, DC 24 V LED 2 LED 2 green, freely configurable, DC 24 V OT onitoring output X 2.4 C Operating voltage guard locking solenoid, DC 24 V X 2. J Version with teach-in input Y Version with feedback loop Version without feedback loop and without teach-in input FE Function earth Not used 80 Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

10 23 19 E Wiring diagram E Pin Designation Function 23 E 1 C Operating voltage guard locking solenoid, DC 24 V 2 I Enable input for channel 1 3 IB Enable input for channel 2 4 O Safety output, channel 1 OB Safety output, channel 2 6 B Operating voltage R electronics, DC 24 V 7 RST Reset input 8 OT D onitoring output (only CET3-R and CET4-R) 9 Not used 10 OT onitoring output 11 Not used 12 FE Function earth J Version with teach-in input 13 Y Version with feedback loop - Version without feedback loop and without teach-in input 14 Not used 1 LED 1 LED 1 red, freely configurable, DC 24 V 16 LED 2 LED 2 green, freely configurable, DC 24 V 17 - Not used 18 0V C Operating voltage guard locking solenoid, DC 0 V 19 0V B Operating voltage R electronics, DC 0 V Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 81

11 12 PVC PR Connection cables with plug connectors For the connection of: CES-P-C01-..-SB CES-P-C.2-..-SB CES-I-P- -SB CES-I-P- -SI CTP-..-P- -SII CTP-..-R- -SB CET.-P- -SI CET.-R- -SG Terminal plug not aligned. Cable outlet not defined For the device installation position shown the following applies: Cable outlet C (left) C Cable outlet (right) Version Cable outlet Order No./item Connection cable with female plug, flying lead, x 0.34 mm² m 10m C-12F0-0X034PV0, C-12F0-0X034PV10, PVC Extension, plug connectors at both ends for connection to decentralized peripheral equipment 20m m 10m 20m C-12F0-0X034PV20, C-12F0-0X034PV0, C-12F0-0X034PV10, C-12F0-0X034PV20, For detailed information, enter the order number 12 PR Connection cable with female plug, flying lead, x 0.2 mm² Extension, plug connectors at both ends for connection to decentralized peripheral equipment 10m 10m C C C-12F0-0X02P10, C-12F0-0X02P10, C-12F0-0X02P10, C-12F0-0X02P10, Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 93

12 ccessories 12 PR Version Cable outlet Order No./item m C-12F0-0X034P0, Connection cable with female plug, flying lead, x 0.34 mm² 10m C-12F0-0X034P10, PR Extension, plug connectors at both ends for connection to decentralized peripheral equipment 20m 30m m 10m C-12F0-0X034P20, C-12F0-0X034P30, C-12F0-0X034P0, C-12F0-0X034P10, For detailed information, enter the order number 20m C-12F0-0X034P20, Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

13 12 8 PVC PR Connection cables with plug connectors For the connection of: CES-P-C01-..-S CES-R-C01-..-S CES-R-C.2-..-S CES-I-R-.-S ESL- -R- -S CE-..-Y- -S CTP-..-P- -S CTP-..-R- -SB CET.-P- -S CET.-R- -SG STTE DI Terminal plug not aligned. Cable outlet not defined For the device installation position shown the following applies: Cable outlet C (left) C Cable outlet (right) Version Cable outlet Order No./item 12 8 PVC Connection cable with female plug, flying lead, 8 x 0.2 mm² m 10m 20m C-12F08-08X02PV0, C-12F08-08X02PV10, C-12F08-08X02PV20, m C-12F08-08X02PV30, m C-12F08-08X02P0, PR Connection cable with female plug, flying lead, 8 x 0.2 mm² Connection cable with female plug, flying lead, 8 x 0.2 mm² 10m 20m 30m C 10m C-12F08-08X02P10, C-12F08-08X02P20, C-12F08-08X02P30, C-12F08-08X02P10, C-12F08-08X02P10, For detailed information, enter the order number 20m C C-12F08-08X02P20, C-12F08-08X02P20, Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 9

14 ccessories 12 R Strapg plug/y-distributors For the series connection of devices on the output family R For the connection of: CES-R-C01-..-S CES-R-C.2-..-S CES-I-R-.-S ESL- -R- -S CTP-L.-R- -SB CET.-R- -SG STTE DI Version Order no. 4 Strapg plug for R series connection with Y-distributors (male plug) R 8 8 1x Y-distributor 12 with connection cable 0,2m x 1m x Y-distributor 12 For detailed information, enter the order number x Not suitable for CTP! Instead please use a Y-distributor with connection cable (see above) 96 Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

15 12 R Passive distribution module For the series connection of devices on the output family R For the connection of: CES-R-C01-..-S CES-R-C.2-..-S CES-I-R-.-S ESL- -R- -S CTP-L.-R- -SB CET.-R- -SG STTE DI Version Order no. 12 R 8 4 x 1x Passive distribution module C-DP-04-S Strapg plug for bypassing unused connections on the passive distribution module (male plug) C-SP-1-S For detailed information, enter the order number Dimension drawing and connection options 34, 22 Connection of function earth X X6 4,3 Connection se X1 X4 - Connection of R devices (CES-R, CET-R,...) or - Bypassing using strapg plug if connection is not used or - Connection of a further passive distribution module (important: only on X1) X Provision of the status signals for all R devices connected X6 Power supply for the R devices and transmission of the safety signals X X H4 X4 4,9 X4 LED X1-X4 green H3 H2 X3 X X3 X2 For details see table Strapg plug C-SP-1-S H1 X1 X1 X1 X6 Connection of a further passive distribution module X Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 97

16 23 19 PR Connection cable with straight plug connector For the connection of: CE- -R- -SH CTP- -R- -SH CET.-R- -SH Version Order no./item 1,m C-23F19-19XDIFP01, m C-23F19-19XDIFP03, m C-23F19-19XDIFP06, PR Connection cable with female plug, flying lead 8m 10m 1m 20m C-23F19-19XDIFP08, C-23F19-19XDIFP08, C-23F19-19XDIFP1, C-23F19-19XDIFP20, For detailed information, enter the order number for the product in the search box at 2m C-23F19-19XDIFP2, m C-23F19-19XDIFP30, m C-23F19-19XDIFP40, Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 99

17 ccessories PR Connection cable with angled plug connector For the connection of: CE- -R- -SH CTP- -R- -SH CET.-R- -SH For the device installation position shown the following applies: Cable outlet C (left) Cable outlet (right) C Order no./item Version C Cable outlet 1,m C-23F19-19XDIFP01, C-23F19-19XDIFP01, m C-23F19-19XDIFP03, C-23F19-19XDIFP03, PR Female connector angled with cable, halogen-free 6m 8m 10m 1m C-23F19-19XDIFP06, C-23F19-19XDIFP08, C-23F19-19XDIFP10, C-23F19-19XDIFP1, C-23F19-19XDIFP06, C-23F19-19XDIFP08, C-23F19-19XDIFP10, C-23F19-19XDIFP1, For detailed information, enter the order number 20m C-23F19-19XDIFP20, C-23F19-19XDIFP20, m C-23F19-19XDIFP2, C-23F19-19XDIFP2, Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

18 ccessories Fixing material ounting sets/mounting plates Series se Order No./item C04 ounting set -SET-PP 2 x ounting set -SET-PPB 1 x 1 x 1 x For safety switch and actuator design C04 Set comprising: 2 x mounting plates For safety switch and actuator design C04 Set comprising: 1 x mounting plate 1 x angle mounting plate 1 x spacer SET-PP SET-PPB ounting bracket -B C40 ounting bracket -B For safety switches CE- -C40 For safety switches CE- -C B B For detailed information, enter the order number ngle mounting plate EP-SB For safety switches CTP EP-SB ounting plate EP-B2 CTP ounting plate EP-B1 For actuators CTP For actuators CTP and actuators CET EP-B EP-B1 ounting plate -P For safety switches CTP P Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

19 ccessories iscellaneous accessories Safety screws Fixing material/screw size Safety screws, stainless steel 4 x 14 (small head) Safety screws, stainless steel 4 x 14 (large head) Safety screws, stainless steel 4 x 20 Safety screws, stainless steel x 10 Safety screws x 16 Safety screws x 2 Version/usage ctuators CES--BB, CES--BC Safety switches CES-..-C.2, actuators CES--BLN-.2 and actuators CTP (straight/angled) Safety switches CES-I-P- -C04 and actuators CES--BBN-C04- Safety switches CES-..-C01, actuators CES--BP and hinged actuators CTP (left/right) ctuators CES--BRN, CET--BWK and actuators -C40 Hinged actuators CTP (top/bottom) Packaging unit [qty.] Order no iscellaneous accessories C40 Designation se Version Order no Lockout bar For safety switches design C E-L-C echanical key release Replacement key Release For safety switches CTP For mechanical key release, identical locking Identical locking, incl. 2 keys Identical locking, key can only be removed in locked position, incl. 2 keys nique locking, incl. 2 keys keys, identical locking CTP For safety switches CTP Resetting Emergency unlocking For safety switches CTP Lead seal kit For emergency unlocking Wire front release Resetting, sheath length 2 m E-B-1-02,0-F (rope length 6 m) For safety switches CTP Resetting, sheath length 3 m (rope length 6 m) E-B-1-03,0-F Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16

20 CTP Designation se Version Order no Handle for wire front release For safety switches CTP Y-HDL Y-HDL Lockout bar For safety switches CTP Lockout bar For safety switches CET E-L-CET echanical key release For safety switches CET Identical locking, incl. 2 keys Replacement key Emergency unlocking For mechanical key release, identical locking 2 keys, identical locking For safety switches CET Latching in both positions CET Lead seal kit For emergency unlocking Cover Door hinge right For safety switches CET and actuators CET Door hinge left Cover For actuators CET C Double ramp For safety switches CET Handle for wire front release For safety switches CET Y-HDL Y-HDL Subject to technical modifications; no responsibility is accepted for the accuracy of this information /16 113