PI5USB268. USB Host Charge Controller IC for Dual USB Ports. Features. Description. Pin Configuration, 20QE (Top View) Applications
|
|
- Lambert Armstrong
- 6 years ago
- Views:
Transcription
1 s Features ÎÎManages communication to allow charging to occur from 2 USB ports ÎÎProvides multiple modes of charging to ensure all of the following specs can be met: BC.0,., &.2 spec YD/T - 59 Chinese Telecom Standard Samsung fast charging Sony Ericsson fast charging Apple fast charging A and 2A Amazon Kindle Fire Certain modes available can also support devices using non standard approaches to charges such as Apple products like iphone, ipod and ipads. ÎÎPatented Automatic USB Device Identification Circuit (used to determine charging mode required) Πα4kV High ESD contact Protection on D+/D- per IEC specification ÎÎ-40ºC to + 85ºC Operating Temperature Range ÎÎPackaging (Pb-free & Green available): 20-pin QSOP (Q) 20-contact TQFN Applications ÎÎLaptops, Netbooks ÎÎUniversal Chargers (Wall, solar, cigarette) ÎÎAutomotive Description USB ports have become the charging connector of choice for the majority of handheld devices such as MP3 players, Mobile phones, MP4 players, DSC, and even tablet/slate type devices. Although the mechanical connector has converged such that these handheld devices can charge using the same cable, the communication scheme followed by each USB device is different when it comes to setting up a charging link. Pericom s PI5USB268 solves the multiple communication protocol problem by supporting all protocols available in the market. Therefore, regardless of what USB device is connected to a charger enabled by Pericom, the USB device will be able to understand the charging setup communication and in turn the USB device will be able to efficiently draw current to charge itself. Pin Configuration, 20QE (Top View) Vdd INT 2 D- 3 D+ 4 S 5 INT2 6 5 D2-7 4 D S2 9 2 Vdd 0 Pin Configuration, 20ZHE (Top View) INT D- D+ S INT2 D2- D2+ S Vdd Vdd /28/3
2 Block Diagram VDD Charger Type Communicator Control D- D+ USB Connector Logic Detection D2- D2+ USB Connector S S2 Pinout Table Pin No. PinName I/O Type Description Ground Ground, 3, 5, 7, 9, 20 N/A No Connect 3 D+ I/O USB positive data bus for port 4 D- I/O USB negative data bus for port 5 S I Control pin. Tie to ground for normal operation 7 D2+ I/O USB positive data bus for port 2 8 D2- I/O USB negative data bus for port 2 9 S2 I Control pin. Tie to ground for normal operation 0, 4, 8 Ground Ground 2, 6 Vdd Power 5V +/- 5% Power Rail 2 INT O n-mosfet open drain output 6 INT2 O n-mosfet open drain output /28/3
3 Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested) All Inputs and Outputs V to V DD +0.5V Storage temperature to +50ºC Ambient Operating Temperature to +85ºC Supply Voltage to Ground Potential (V DD) V Junction Temperature...+50ºC Soldering Temperature (Max of 0 seconds) ºc Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Stress beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Recommended Operation Conditions Parameter Min. Typ. Max. Unit Ambient Operating Temperature ºC Power Supply Voltage (measured in respect to ) +4.75V V DC Electrical Characteristics (V DD = 5.0V +/- 5%, Ambient Temperature -40 to +85 o C) Symbol Parameter Conditions Min. Typ. Max. Unit V DD Operating Voltage V I DD S = S2 = low V DD = 4.75V V DD = 5.25V V IL for S/S2 Input Low Voltage 0.6 V V OL for INT I OFF Output low voltage for INT Signal voltage on D+/Dwhen chip is OFF PI5USB268, I OL= 4mA 0.25 V V dd = 0v, V IN = 0v to 5.25v µa ma /28/3
4 Notes:. All dimensions are in mm. Angles in degrees. 2. Coplanarity applies to the exposed pad as well as the terminals. 3. Refer JEDEC MO Recommended land pattern is for reference only. 5. Thermal pad soldering area (mesh stencile design is recommended) DESCRIPTION: 20-contact, Very Thin Quad Flat No-Lead (TQFN) PACKAGE CODE: ZH20 DOCUMENT CONTROL #: PD-2032 DATE: 09/07/0 REVISION: B For latest package info, please check: /28/3
5 Guage Plane 0.20 MIN DOCUMENT CONTROL NO. PD REVISION: H DATE: 0/22/ Detail A REF REF SEATING PLANE.05 x Detail A BSC X.XX X.XX DENOTES DIMENSIONS IN MILLIMETERS ) Controlling dimensions in inches. 2) Ref: JEDEC MO-37B/AD 3) Dimensions do not include mold flash, protrusions or gate burrs Pericom Semiconductor Corporation 3545 N. st Street, San Jose, CA DESCRIPTION: 20-Pin, 50-Mil Wide, QSOP PACKAGE CODE: Q For latest package info, please check: Ordering Information Ordering Code Package Code Package Type Top Mark PI5USB268QE QE Pb-free & Green, 20 pin QSOP PI5USB268QE PI5USB268ZHE ZHE Pb-free & Green, 20 contact TQFN PI5USB268ZHE Thermal characteristics can be found on the company web site at E = Pb-free and Green Adding an X suffix = Tape/Reel Pericom Semiconductor Corporation /28/3
PI5USB66. USB Charge Controller IC for Single USB Port. Features. Description. Pin Configuration. Applications
Features ÎÎManages communication to allow charging to occur ÎÎProvides multiple modes of charging to ensure all of the following specs can be met: DCP mode per USB BC.0,., &. spec YD/T - 59 charger spec
More informationPI5USB1468 PI5USB1468A
Features ÎÎManages communication to allow charging to occur ÎÎProvides multiple modes of charging to ensure all of the following specs can be met: DCP, CDP, and SDP per BC.0,.,. spec DCP per YD/T-59 spec
More informationPI5USB1458/PI5USB1458A. Features. Description. Block Diagram. A product Line of Diodes Incorporated
USB Host Charger Controller supporting BC., YD/T-59, & Non-standard Protocols Features ÎÎManages communication to allow charging to occur ÎÎProvides multiple modes of charging to ensure all of the following
More informationPI2PCIE2214. PCI Express 2.0, 1-lane, 4:1 Mux/DeMux Switch. Features. Description. Application. Pin Description. Block Diagram.
Features 2 Differential Channel, 4:1 Mux/DeMux PCI Express 2.0 performance, 5.0 Gbps Low Bit-to-Bit Skew, 7ps Max. Low Crosstalk: -23dB@3GHz Low Off Isolation: -23dB@3GHz Operating Range: 1.8V ±10% ESD
More informationPI6C20800B. PCI Express 3.0 1:8 HCSL Clock Buffer. Features. Description. Pin Configuration (48-Pin TSSOP)
PCI Express 3.0 1:8 HCSL Clock Buffer Features Î ÎPhase jitter filter for PCIe 3.0 application Î ÎEight Pairs of Differential Clocks Î ÎLow skew < 50ps (PI6C20800B),
More informationPI6C20800S. PCI Express 1:8 HCSL Clock Buffer. Features. Description. Pin Configuration. Block Diagram
Features Phase jitter filter for PCIe application Eight Pairs of Differential Clocks Low skew < 50ps (PI6C20800S),
More informationDescription OUT0 1 OUTA1 OUTA1 2 OUTA2 3 OUTA3 OUTA4 OUTB1 6 OUTB2 7 OUTB2 OUTB3 OUTB4. All trademarks are property of their respective owners.
Features Maximum rated frequency: 133 MHz Low cycle-to-cycle jitter Input to output delay, less than 200ps Internal feedback allows outputs to be synchronized to the clock input Spread spectrum compatible
More informationPI6C20400A. 1:4 Clock Driver for Intel PCIe Chipsets. Features. Description. Pin Configuration. Block Diagram
Features Phase jitter filter for PCIe 2.0 application Four Pairs of Differential Clocks Low skew < 50ps Low jitter < 50ps cycle-to-cycle < 1 ps additive RMS phase jitter Output Enable for all outputs Outputs
More informationDescription. Application. Block Diagram
3.3V PCI Express 3.0 2-Lane Exchange Switch Features ÎÎ8 Differential Channel (2-lane) Exchange ÎÎPCI Express 3.0 performance, 8.0 Gbps ÎÎBi-directional operation ÎÎLow Bit-to-Bit Skew: 10ps (between ±
More informationK T6001. Smart USB Charging Port Controller. General Description. Applications. Features. Ordering Information
K CA Car Chargers Computer Peripherals Wall Adaptors USB Power Plugs Portable Power Banks General Description The K T6001 is a smart USB interface IC specifically designed for dedicated charging port applications.
More informationPI6CEQ PCIe Gen2 / Gen3 Buffer. Features. Description. Applications. Block Diagram. Pin Configuration (20-Pin TSSOP & 20-Pin QSOP)
PCIe Gen2 / Gen3 Buffer Features ÎÎPCIe Gen2/ Gen3* compliant clock buffer/zdb * Gen3 performance only available in Commercial temp ÎÎInternal equalization for better signal integrity ÎÎ2 HCSL outputs
More informationPI6C :4 Clock Driver for Intel PCI Express Chipsets. Features. Description. Block Diagram. Pin Configuration
Features Four Pairs of Differential Clocks Low skew < 50ps Low jitter < 50ps Output Enable for all outputs Outputs tristate control via SMBus Power Management Control Programmable PLL Bandwidth PLL or
More informationPI6C557-01BQ. PCIe 3.0 Clock Generator with 1 HCSL Outputs. Features. Description. Pin Configuration (16-Pin TQFN) Block Diagram
s Features ÎÎPCIe 3.0 compliant à à Phase jitter - 0.45ps RMS (High Freq. Typ.) ÎÎLVDS compatible output ÎÎSupply voltage of 3.3V ±10% ÎÎ25MHz crystal or clock input frequency ÎÎHCSL outputs, 0.8V Current
More informationUSB Charging Controller
USB Charging Controller Features D+/D DCP Mode per USB Battery Charging Specification 1.2 D+/D Short Mode per Telecommunication Industry Standard YD/T1591 2009 (Chinese) Supports non BC1.2 Charging Modes
More informationPI5USB2549 USB Charging Port Controller and Load Detection Power Switch
Features Supports DCP Modes per USB Battery Charging Specification 1.2 Supports Shorted Mode per Chinese Telecommunication Industry Standard YD/T1591-2009 Supports non-bc1.2 Charging Modes by Automatic
More informationName Operation Temperature Package Package Mark
USB Charging Controller Features D+/D- DCP Mode per USB Battery Charging Specification 1.2 D+/D- Short Mode per Telecommunication Industry Standard YD/T1591-2009 (Chinese) Supports non-bc1.2 Charging Modes
More informationUSB Charging Controller. Features. General Description. Applications. Order Information
USB Charging Controller Features D+/D DCP Mode per USB Battery Charging Specification 1.2 D+/D Short Mode per Telecommunication Industry Standard YD/T1591 2009 (Chinese) Supports non BC1.2 Charging Modes
More informationPART OBSOLETE - USE PI3PCIE3442A
PART OBSOLETE - USE A 3.3V PCI Express 3.0 2-Lane Exchange Switch Features ÎÎ8 Differential Channel (2-lane) Exchange ÎÎPCI Express 3.0 performance, 8.0 Gbps ÎÎBi-directional operation ÎÎLow Bit-to-Bit
More informationZS5889. USB Charging Controller
Features D+/D- DCP Mode per USB Battery Charging Specification 1.2 D+/D- Short Mode per Telecommunication Industry Standard YD/T1591-2009 (Chinese) Supports non-bc1.2 Charging Modes by Automatic Selection
More informationF USB Charger Controller F Release Date: Dec., 2011 Version: V0.11P. Nov., 2011 Data Sheet
USB Charger Controller Release Date: Dec., 2011 Version: V0.11P F75204 Datasheet Revision History Version Date Page Revision History Data Brief 2011/10 - Data Brief 0.10P 2011/ 11 Up Date AC/DC SPECs 0.11P
More informationFP6600. USB Dedicated Charging Port Controller with QC 2.0 Fast Charging Function. Features. Description. Applications.
USB Dedicated Charging Port Controller with QC 2.0 Fast Charging Function Description The is a fast charge protocol controller and follows Quick Charge 2.0 specification for smart power bank application.
More informationCW3003CW3004R04. Dual-Channel USB Charging Controller. Features. General Description. Applications. Order Information
CW3003 CW3004 Dual-Channel USB Charging Controller Features D+/D- DCP Mode per USB Battery Charging Specification 1.2 D+/D- Short Mode per Telecommunication Industry Standard YD/T1591-2009 (Chinese) Supports
More informationPI3PCIE V, PCI Express 1-lane, 2:1 Mux/DeMux Switch. Features. Description. Application. Pin Description (Top-side view) Truth Table
3.3V, PCI Express 1-lane, Features 2 Differential Channel, 2:1 Mux/DeMux PCI Express 2.0 Performance, 5.0Gbps Pinout optimized for placement between two PCIe slots Bi-directional operation Low Bit-to-Bit
More informationWT6632F (Standard Code Version) USB Power Delivery Controller
WT6632F (Standard Code Version) Data Sheet Rev. 1.0 September 2016 Copyright Notice This data sheet is copyrighted by Weltrend Semiconductor, Inc. Do not reproduce, transform to any other format, or send/transmit
More informationPI6C Low Power Networking Clock Generator. Description. Features. Block Diagram. 100MHz PCI-Express 0 100MHz PCI-Express 1 100MHz PCI-Express 2
Features ÎÎ25 MHz crystal or clock input ÎÎThree differential 100 MHz PCI-Express clock outputs push-pull termination ÎÎSpread spectrum capability on all 100 MHz PCI-e clock outputs with -0.5% down spread
More informationUC2633/UC2634. APPLICATIONS Power Bank/Car Charger USB Wall Adapter Travel Charger PACKAGE AND APPLICATION
DESCRIPTION The UC2633/UC2634 is single/dual USB adapter emulators with automatic host charger identification circuitry for USB dedicated chargers. The devices integrated automatic USB charger identification
More informationGeneral Description. Applications. Typical Operating Circuit
General Description The MAX14631/MAX14633 are USB charger adapter emulators with automatic host-charger identification circuitry for USB-dedicated chargers. The devices allow USB wall adapters, travel
More informationDescription. Block Diagram DDC_SCL DDC_SDA AUX+ AUX- TB_Rx_1(p) TB_Rx_1(n) CA_DET_Out. CA_DET_Out
10.3Gbps Thunderbolt and DisplayPort Switch Features ÎÎSupports 5.4Gbps for DisplayPort 1.2 and 10.3Gbps for Thunderbolt Electrical Standard ÎÎSupports DP and DP++ Configuration ÎÎSupports AUX and DDC
More informationMP6219 5V, 1A 2A Programmable Current Limit Power Distribution Switch
The Future of Analog IC Technology MP6219 5V, 1A 2A Programmable Current Limit Power Distribution Switch DESCRIPTION The MP6219 is a protection device designed to protect circuitry on the output from transients
More informationPI5USB2543. USB Power Switch with Pericom's FAST Charger Circuitry for DCP, CDP, and 2A ipad support. Features. Description
PI5USB5 Circuitry for DCP, CDP, and A ipad support Features ÎÎUSB charger controller that supports SDP, DCP and CDP per USB BC.0,., and. specfication ÎÎDCP (Dedicated charger port) is used when enumeration
More informationLow-Capacitance, 2/3/4/6-Channel, ±15kV ESD Protection Arrays for High-Speed Data Interfaces
9-739; Rev 5; 6/ General Description The are low-capacitance ±5kV ESD-protection diode arrays designed to protect sensitive electronics attached to communication lines. Each channel consists of a pair
More informationLow Capacitance ESD Protection - SP3002 Series. Description. Features I/O 4 I/O 3. Applications
SP3002 Series 0.85pF Diode Array RoHS Pb GREEN Description The SP3002 has ultra low capacitance rail-to-rail diodes with an additional zener diode fabricated in a proprietary silicon avalanche technology
More informationPI3HDMI231-A. 3:1 ActiveEye HDMI TM Switch with Electrical Idle Detect
Features 3 digital video inputs can be switched to a single output Each input can be AC coupled video or DC coupled, while the output will maintain its DC coupled, current-steering, TMDS compliance TMDS
More informationFAN3989 USB/Charger Detection Device with Load Switch
FAN3989 USB/Charger Detection Device with Load Switch Features Charger/USB Detection Device with Load Switch Charger/USB Device Detection Flag Over/Under-Voltage Detection Flag Load Switch Output, Up to
More informationMP5013A 5 V, 5 A Programmable Current-Limit Switch with Over-Voltage Clamp and Slew-Rate Control in TSOT23-8
The Future of Analog IC Technology MP5013A 5 V, 5 A Programmable Current-Limit Switch with Over-Voltage Clamp and Slew-Rate Control in TSOT23-8 DESCRIPTION The MP5013A is a protection device designed to
More informationAZC099-04S 4 IEC (ESD)
Features ESD Protect for 4 high-speed I/O channels Provide ESD protection for each channel to IEC 000-4- (ESD) ±kv (air), ±8kV (contact) IEC 000-4-4 (EFT) (/0ns) Level-3, 0A for I/O, 40A for Power IEC
More informationFST3257 Quad 2:1 Multiplexer / Demultiplexer Bus Switch
FST3257 Quad 2:1 Multiplexer / Demultiplexer Bus Switch Features 4Ω Switch Connection Between Two Ports Minimal Propagation Delay Through the Switch Low I CC Zero Bounce in Flow-Through Node Control Inputs
More informationPART OBSOLETE - USE PI3PCIE3242A
PART OBSOLETE - USE A 3.3V PCI Express 3.0 4 Channel 2x2 Exchange Switch Features ÎÎ4 Differential Channel 2x2 Exchange Switch ÎÎPCI Express 3.0 performance, 8.0 Gbps ÎÎBi-directional operation ÎÎLow Bit-to-Bit
More informationup7535 Dual-Input Triple-Output Power Multiplexer in PSOP-8L for USB High Side Switch General Description Ordering Information Applications
Dual-Input Triple-Output Power Multiplexer in PSOP-8L for USB High Side Switch The up7535 is a current limited, dual-input triple-output power multiplexer acting as a high side switch for USB applications
More informationPI3B3253. Description. Features. Pin Configuration (QSOP, TSSOP) Block Diagram. Pin Configuration (UQFN) Truth Table (1)
3.3V, Dual 4:1 Mux/DeMux NanoSwitch Features Near-Zero propagation delay 5Ω switches connect inputs to outputs Fast Switching Speed: 5.2ns max. Ultra Low Quiescent Power (0.2µA typical) Ideally suited
More informationRClamp0504FA RailClamp Low Capacitance TVS Array
- RailClamp Description RailClamp low capacitance TVS array designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected
More informationIEC (EFT) 40A
Features ESD Protect for high-speed I/O channels Provide ESD protection for each channel to IEC 61000-4- (ESD) ±1kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (/0ns) IEC 61000-4- (Lightning) 1A (8/0µs)
More informationTwo-wire Serial EEPROM AT24C01A AT24C02 AT24C04 AT24C08 (1) AT24C16 (2)
Features Low-voltage and Standard-voltage Operation.7 (V CC =.7V to.v).8 (V CC =.8V to.v) Internally Organized 8 x 8 (K), 6 x 8 (K), x 8 (4K), 04 x 8 (8K) or 048 x 8 (6K) Two-wire Serial Interface Schmitt
More informationPI6LC48L0201A 2-Output LVDS Networking Clock Generator
Features ÎÎTwo differential LVDS output pairs ÎÎSelectable crystal oscillator interface or LVCMOS/LVTTL single-ended clock input ÎÎSupports the following output frequencies: 62.5MHz, 125MHz, 156.25MHz
More information2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS Description. Features. Block Diagram DATASHEET
DATASHEET 2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS557-08 Description The ICS557-08 is a 2:1 multiplexer chip that allows the user to select one of the two HCSL (Host Clock Signal Level) or LVDS input pairs
More information1-megabit (64K x 16) 5-volt Only Flash Memory AT49F1024A Features Description Pin Configurations
BDTIC www.bdtic.com/atmel Features Single-voltage Operation 5V Read 5V Reprogramming Fast Read Access Time 45 ns Internal Program Control and Timer 8K Word Boot Block with Lockout Fast Erase Cycle Time
More informationChrontel CH7231A USB Type-C Electronically Marked Cable Component
Chrontel Chrontel USB Type-C Electronically Marked Cable Component Features Component for USB Type-C electronically marked cable (USB Type-C Specification 1.2) Support USB power delivery specification
More informationSDC36C. TVS Diode Array for Proximity Switch Input Protection. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics.
Description The is a highsurge transient voltage suppressor (TS) optimized for protection of sensitive digital sensors used in proximity switches and industrial control applications. The protects the components
More informationPI3VDP411LS. Digital Video Level Shifter from AC Coupled Digital Video Input to a DVI/HDMI Transmitter. Features. Description
Features ÎÎConverts low-swing AC coupled differential input to HDMI rev 1.3 compliant open-drain current steering Rx terminated differential output ÎÎHDMI level shifting operation up to 2.5Gbps per lane
More informationHM9708 HM9708. Battery-Powered Equipment Motherboard USB Power Switch USB Device Power Switch Hot-Plug Power Supplies Battery-Charger Circuits DC+ VIN
200mΩ Power Distribution Switches Features 200mΩ Typ. High-Side MOSFET 0.8A Current Limit (V IN =3.0V) Wide Input Voltage Range: 2V ~ 5.5V Soft Start Thermal Protection Small SOT-23-5 Package Minimizes
More informationAZC002-02N Low Capacitance ESD Protection Array For High Speed Data Interfaces Features IEC (ESD) ±15kV (air), ±8kV (contact)
Features ESD Protect for 2 high-speed I/O channels Provide ESD protection for each channel to IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) (5/50ns) Level-3, 20A for I/O, 40A for
More information74F00 Quad 2-Input NAND Gate
Quad 2-Input NAND Gate General Description This device contains four independent gates, each of which performs the logic NAND function. Ordering Code: December 1994 Revised September 2000 Order Number
More informationSDC15. TVS Diode Array for ESD Protection of 12V Data and Power Lines. PROTECTION PRODUCTS Description. Features. Mechanical Characteristics
Description The transient voltage suppressor (TVS) is designed to protect components which are connected to data and transmission lines from voltage surges caused by electrostatic discharge (ESD), electrical
More informationICS548A-03 LOW SKEW CLOCK INVERTER AND DIVIDER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS548A-03 Description The ICS548A-03 is a low cost, low skew, high-performance general purpose clock designed to produce a set of one output clock, one inverted output clock, and one clock divided-by-two.
More informationFP6601QS6. USB Dedicated Charging Port Controller for Fast Charging Protocol and QC 2.0/3.0. Description. Features. Applications. Ordering Information
USB Dedicated Charging Port Controller for Fast Charging Protocol and QC 2.0/3.0 Description The FP6601Q is a fast charge protocol controller for HiSilicon Fast Charging Protocol (FCP) and Qualcomm Quick
More informationRClamp0504F RailClamp Low Capacitance TVS Array
- RailClamp Description RailClamps are surge rated diode arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected
More informationMAS6240 Piezo Driver with Multi-Mode Charge Pump
MAS624 Piezo Driver with Multi-Mode Charge Pump Both Single Ended and Differential Output Three-Step Volume Adjusting Up to 8Vpp Output from 3V Supply One Wire Audio & Shutdown Control High Efficiency
More informationPI6C GND REF_IN+ V TH V REF-AC REF_IN- Q0+ Q0- Q1+ Q1- VDD. 6 GHz / 12 Gbps Clock / Data Fanout Buffer with Internal Termination.
Features ÎÎInput Clock Frequency up to 6 GHz Typical ÎÎMaximum Input Data Rate up to 12 Gbps Typical ÎÎ2 pairs of differential CML outputs ÎÎLow additive jitter, < 0.05ps (max) ÎÎInput accepts: CML, LVDS,
More information36V-Capable Overvoltage Protector with Regulated Output Voltage
19-5570; Rev 1; 8/11 36V-Capable Overvoltage Protector with General Description The protects valuable consumer circuits against voltage faults of up to +36V. This robust protection is implemented in a
More informationPI3HDMI Port HDMI Signal Switch with I 2 C Control. Features. Description
Features 3:1 HDMI Switch Mux Non-Blocking EQ path for ideal EQ control in main Receiver chipset -3dB bandwidth up to 5Gbps to support HDMI 1.3a (16-bit color depth per channel) HDMI 1.4 data rate ready
More informationLPM355X USB to Serial Converter
to Serial Converter Doc. Rev.0 (31/07/12) Features All-In-One to Serial Converter. 2.0 Full Speed compatible. Wide serial lines voltage range 2.7V to 5.5V. Baudrate up to 921.6Kbps. No external components
More information2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS Features
DATASHEET 2:1 MULTIPLEXER CHIP FOR PCI-EXPRESS ICS557-08 Description The ICS557-08 is a 2:1 multiplexer chip that allows the user to select one of the two HCSL (Host Clock Signal Level) input pairs and
More informationCEP8120 Rev 1.0, March, 2015
USB Dedicated Charging Port Controller FEATURES Supports USB DCP Shorting D+ Line to D Line per USB Battery Charging Specification, Revision 1.2 (BC1.2) Supports Shorted Mode (Shorting D+ Line to D- Line)
More informationWE05R. Features. Transient Voltage Suppressor IEC COMPATIBILITY (EN ) SOT-143 (Top View) Document: W , Rev: A
Document: W0005, Rev: A Transient Voltage Suppressor Features 00Watts Peak Power per Line (tp = 8/0μs) Protects two I/O lines Low operating voltage: 5V Ultra Low capacitance(
More informationPI6C GHz 1:4 LVPECL Fanout Buffer with Internal Termination GND Q0+ Q0- REF_IN+ V TH V REF-AC REF_IN- Q1+ Q1- Q2+ Q2- Q3+ Q3- VDD.
Features ÎÎInput Clock Frequency up to 6 GHz Typical ÎÎ4 pairs of differential LVPECL outputs ÎÎLow additive jitter, < 0.05ps (max) ÎÎInput CLK accepts: LVPECL, LVDS, CML, SSTL input level ÎÎOutput to
More informationPreamplifier Circuit for IR Remote Control
Preamplifier Circuit for IR Remote Control FEATURES Carrier-out-function: carrier frequency and burst length accurately correspond to the input signal Small QFN package with 2 mm width Can be used with
More informationMAX14653/MAX14654/ MAX14655/MAX High-Current Overvoltage Protectors with Adjustable OVLO
EVALUATION KIT AVAILABLE MAX14653/MAX14654/ General Description The MAX14653/MAX14654/ overvoltage protection devices feature a low 38mΩ (typ) R ON internal FET and protect low-voltage systems against
More informationSP5001 Series 4 Channel Common Mode Filter with ESD Protection
Low Capacitance ESD Protection - SP51 Series SP51 Series 4 Channel Common Mode Filter with ESD Protection RoHS Pb GREEN Description The SP51 Series is a highly integrated Common Mode Filter (CMF) providing
More informationAOZ8900. Ultra-Low Capacitance TVS Diode Array PRELIMINARY. Features. General Description. Applications. Typical Application
Ultra-Low Capacitance TS Diode Array General Description The is a transient voltage suppressor array designed to protect high speed data lines from Electro Static Discharge (ESD) and lightning. This device
More informationMAX9650/MAX9651 High-Current VCOM Drive Op Amps for TFT LCDs
General Description The MAX965/MAX9651 are single- and dual-channel VCOM amplifiers with rail-to-rail inputs and outputs. The MAX965/MAX9651 can drive up to 13mA of peak current per channel and operate
More informationSGM2031 Low Power, Low Dropout, RF - Linear Regulators
RF - Linear Regulators GENERAL DESCRIPTION The series low-power, low-dropout, CMOS linear voltage regulators operate from a 2.5V to 5.5V input voltage in an ultra small package. They are the perfect choice
More informationAZC002-04S Low Capacitance ESD Protection Array For High Speed Data Interfaces Features IEC (ESD) ±15kV (air), ±8kV (contact)
Features ESD Protect for 4 high-speed I/O channels Provide ESD protection for each channel to IEC 000-4- (ESD) ±kv (air), ±8kV (contact) IEC 000-4-4 (EFT) (/0ns) Level-3, 0A for I/O, 40A for Power IEC
More information5 V Charge Pump HDMI Tx Companion Chip AD9394
Data Sheet FEATURES 5 V at 55 ma output for an HDMI +5 V requirement For hot plug detect with HDMI Tx 3.3 V at 60 ma output Lithium battery input: 2.5 V to 4.5 V Short-circuit limitation: 00 ma 3 4 array
More informationSGM2032 Low Power, Low Dropout, RF Linear Regulators
GENERAL DESCRIPTION The SGM2032 series low power, low noise, low dropout, CMOS linear voltage regulators operate from a 2.5V to 5.5V input voltage. They are the perfect choice for low voltage, low power
More informationAOZ8234. Four-line TVS Diode
AOZ8 Four-line TS Diode General Description The AOZ8 is a transient voltage suppressor diode array designed to protect data lines from high transient conditions and ESD. This state-of-the-art device utilizes
More informationSGM mA, Low Power, Low Dropout 3 -Terminal, Linear Regulators
3 -Terminal, Linear Regulators GENERAL DESCRIPTION The series low-power, low-noise, low-dropout, CMOS linear voltage regulators operate from a 2.5V to 5.5V input voltage. They are the perfect choice for
More information24C08/24C16. Two-Wire Serial EEPROM. Preliminary datasheet 8K (1024 X 8)/16K (2048 X 8) General Description. Pin Configuration
Two-Wire Serial EEPROM Preliminary datasheet 8K (1024 X 8)/16K (2048 X 8) Low-voltage Operation 1.8 (VCC = 1.8V to 5.5V) Operating Ambient Temperature: -40 C to +85 C Internally Organized 1024 X 8 (8K),
More informationSGM2020 Low Power, Low Dropout, RF - Linear Regulators
GENERAL DESCRIPTION The series low-power, low-noise, low-dropout, CMOS linear voltage regulators operate from a 2.5V to 5.5V input voltage. They are the perfect choice for low voltage, low power applications.
More informationAIC A Dual USB High-Side Power Switch FEATURES DESCRIPTION APPLICATIONS TYPICAL APPLICATION CIRCUIT
1.0A Dual USB High-Side Power Switch FEATURES 2.7V to 6.5V Input Voltage Range 1.0A Dual Continuous Load Current 100mΩ High-Side P-MOSFET Switch 20Ω Open-Drain Over-Current Flag Output 80uA Quiescent Supply
More informationPentium Processor Compatible Clock Synthesizer/Driver for ALI Aladdin Chipset
1CY 225 7 fax id: 3517 Features Multiple clock outputs to meet requirements of ALI Aladdin chipset Six CPU clocks @ 66.66 MHz, 60 MHz, and 50 MHz, pin selectable Six PCI clocks (CPUCLK/2) Two Ref. clocks
More information1-Megabit (128K x 8) Low Voltage Paged Parallel EEPROMs AT28LV010
BDTIC www.bdtic.com/atmel Features Single 3.3V ± 10% Supply Fast Read Access Time 200 ns Automatic Page Write Operation Internal Address and Data Latches for 128 Bytes Internal Control Timer Fast Write
More information16-megabit 2.5-volt or 2.7-volt DataFlash AT45DB161D
Features Single 2.5V - 3.6V or 2.7V - 3.6V Supply RapidS Serial Interface: 66 MHz Maximum Clock Frequency SPI Compatible Modes 0 and 3 User Configurable Page Size 512 Bytes per Page 528 Bytes per Page
More informationRClamp0504PA RailClamp Low Capacitance TVS Array
- RailClamp Description RailClamp TVS diodes are specifically designed to protect sensitive components which are connected to high-speed data and transmission lines from overvoltage caused by ESD (electrostatic
More informationSDP Biased Series - SOT23-6
SDP Biased Series - SOT23-6 RoHS Pb e3 Description This new SDP Biased series provides overvoltage protection for applications such as VDSL2, ADSL2, and ADSL2+ with minimal effect on data signals. This
More informationMP201 Dying Gasp Storage and Release Control IC
The Future of Analog IC Technology MP201 Dying Gasp Storage and Release Control IC DESCRIPTION The MP201 is a dying gasp storage and release controller. It charges storage capacitor from the input during
More informationMAX14606/MAX14607 Overvoltage Protectors with Reverse Bias Blocking
EVALUATION KIT AVAILABLE MAX1466/MAX1467 General Description The MAX1466/MAX1467 overvoltage protection devices feature low 54mI (typ) on-resistance (RON) internal FETs and protect low-voltage systems
More informationRClamp0502A RailClamp Low Capacitance TVS Array
- RailClamp Description The RailClamp series consists of ultra low capacitance TS arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive
More informationProduct Data Sheet MA5885 (USB Fast Charging Emulator)
Table of Contents 1. Description... 2 2. Feature... 2 3. Target Application... 3 4. MA5885 Charging Modes... 3 5. Detail Function Description... 4 6. Pin Assignment... 6 7. Pin Description... 6 8. Electrical
More informationChrontel CH7251A for USB Type-C Charger
Chrontel for USB Type-C Charger Features Component for USB Type-C Charger(USB Type-C Specification 1.2) On chip 3A switch. On chip over voltage, over current and over temperature detection and protection.
More information奥科迪科技 ( 授权代理 ) 蔡小姐 QQ: 电话 :
USB Dedicated Charging Port Controller for Fast Charging Protocol and QC 2.0/3.0 Description The is a fast charge protocol controller for HiSilicon Fast Charging Protocol (FCP) and Qualcomm Quick Charge
More informationDescription. Features. Pin Configuration PI4IOE5V9539
16-bit I 2 C-bus and SMBus low power I/O port with interrupt and reset Features Operation power supply voltage from 2.3V to 5.5V 16-bit I 2 C-bus GPIO with interrupt and reset 5V tolerant I/Os Polarity
More information1000 Base-T, ±15kV ESD Protection LAN Switch
19-0841; Rev 0; 6/07 1000 Base-T, ±15kV ESD Protection LAN Switch General Description The meets the needs of high-speed differential switching, including that of Gigabit Ethernet (10/100/1000) Base-T switching
More informationMX877RTR. 8-Channel, 60V Driver with Push-Pull Output, 3 Wire Interface INTEGRATED CIRCUITS DIVISION. Features. Description.
8-Channel, 6V Driver with Push-Pull Output, 3 Wire Interface Features Eight (8) Outputs Rated at 6V, ±8mA Push-Pull Driver Configuration 6V to 6V Driver Supply Range 2.7V to 5.5V Logic Supply Range 3-Wire
More information1, 2, 4 and 8-Channel Very Low Capacitance ESD Protectors
1, 2, 4 and 8-Channel Very Low Capacitance ESD Protectors CM1210 Features 1,2,4 and 8 channels of ESD protection Very low loading capacitance (1.0pF typical) ±6 kv ESD protection per channel (IEC 61000-4-2
More informationAOZ8882. Ultra-Low Capacitance TVS Diode Array. General Description. Features. Applications. Typical Application
Ultra-Low Capacitance TS Diode Array General Description The AOZ8882 is a transient voltage suppressor array designed to protect high speed data lines such as HDMI, MDDI, USB, SATA, and Gigabit Ethernet
More informationZSPM4121. Under-Voltage Load Switch for Smart Battery Management. Datasheet. Brief Description. Features. Related IDT Smart Power Products
Under-Voltage Load Switch for Smart Battery Management ZSPM4121 Datasheet Brief Description The ZSPM4121 battery management load switch can be used to protect a battery from excessive discharge. It actively
More informationRClamp0504S RailClamp Low Capacitance TVS Array
- RailClamp Description RailClamps are surge rated diode arrays designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected
More informationDiscontinued Product
Hall Effect Direction Detection Sensor Discontinued Product This device is no longer in production. The device should not be purchased for new design applications. Samples are no longer available. Date
More informationOvervoltage-Protection Controllers with a Low RON Internal FET MAX4970/MAX4971/MAX4972
19-4139; Rev 1; 8/08 Overvoltage-Protection Controllers General Description The family of overvoltage protection devices features a low 40mΩ (typ) R ON internal FET and protect low-voltage systems against
More information2 TO 4 DIFFERENTIAL CLOCK MUX ICS Features
DATASHEET 2 TO 4 DIFFERENTIAL CLOCK MUX ICS557-06 Description The ICS557-06 is a two to four differential clock mux designed for use in PCI-Express applications. The device selects one of the two differential
More information