Technical Specification V1.0 AC-DC Power Module YA5 Series

Transcription

1 YA5 Series Modules Outline Diagram 47.00(1.850) (1.378) 2 BOTTOM (0.394) 20.00(0.787) 45.0(1.77) (2.17) Features Industry Size55.0mm 45.0 mm 21.0mm Universal Input Voltage 2500V ac Isolation Voltage 60kHz Switching Frequency Short Circuit Protection, Auto Recovery 100% Burn-in 2-year warranty Pin single dual (balanced load) dual (unbalanced load) 21.0(0.83) triple 1 L L L L 2 N N N N 3 FG FG FG FG 4 -Vo -Vo -Vo1 -Vo1 5 NP NP +Vo1 +Vo1 6 NP COM NC Vo3 7 NP NP -Vo2 COM 8 +Vo +Vo +Vo2 Vo2 Case material: Black plastic, UL94V-0. Pins material:copper, tin-cerium plating Notes:All dimensions in mm (inches) Tolerances: X.X±0.5 (X.XX±0.02) X.XX±0.25 (X.XXX±0.010) Performance Specifications And Ordering Guide Unless otherwise specified, all values are given at: 25, one standard atmosphere pressure, pure resistive load and basic connection. Output Input Model Ripple and Capacitive Range-AC Voltage(V) Current(A) Noise load(uf) (Volts) Single YAS5-3-N % YAS5-5-N % YAS5-12-N % YAS5-15-N % Page 1 of 9 April 19, 2012

2 Continue Model Voltage(V) Output Ripple and Current(A) Noise Capacitive load(uf) Input Range-AC (Volts) YAS5-24-N % YAS5-48-N % YAS5-5-W % YAS5-12-W % YAS5-15-W % Dual YAD5-5-N +5.05/ / / / % YAD NI 5/12 0.8/0.1 50/ / % YAD NI 5/24 0.6/0.1 50/ / % YAD5-05H12-NI 5/12 0.6/0.2 50/ / % YAD5-05H15-NI 5/15 0.6/ / / % YAD5-5-W +5.05/ / / / % YAD5-12-W +12/ / / / % YAD WI 5/5 1.0/0.1 50/ / % YAD WI 5/24 0.6/0.1 50/ / % YAD5-05H05-WI 5/5 0.8/0.2 50/ / % YAD5-05H12-WI 5/12 0.6/0.2 50/ / % Triple YAT NI 5/+5/-5 0.8/+0.1/ /100/ /220/ % YAT WI 5/+12/ /+0.1/ /100/ /220/ % Performance/Functional Specifications Input Input ltage: AC:165~265 DC:200~375 Suffix-N AC:85~265 DC:100~375 Suffix-W Input Frequency: 45~64Hz Output Voltage Accuracy: ±1% Vo1 ±3% Vo2Vo3 Line Regulation: Load Regulation: ±0.2%max. ±0.5% max. Ripple and Noise: 50mVp-p Vo5Vdc 100 mvp-p Other 200 mvp-p Vo48Vdc : Transient Response Recovery Time(µs): Transient ResponseVoltage Deviation (%): Start-up Delay Time: Rise Time: See Ordering Guide see respective data sheet see respective data sheet see respective data sheet see respective data sheet Isolation Voltage: Switching Frequency: General 2500Vac 1min/5mA (Input-Output) 60kHz(typ.) MTBF h (Bellcore RT332, 25) Temperature Coeffcient: ±0.1% per (Max) Case Temperature: Storage Temperature: (Commercial) Relative Humidity: 10%~90% Short-circuit Protection: Hiccup mode, automatic recovery Isolation Resistance: Manual Soldering: Wave Soldering: 100 MΩmin (500V dc 90%RH) 425max (5s Max) 255max (10s Max) Weight: 60~75g Page 2 of 9 April 19, 2012

3 Characteristic Curves Page 3 of 9 Derating YAS5-3-N YAS5-5-N YAS5-12-N YAS5-15-N YAS5-3-N YAS5-5-N YAS5-12-N YAS5-15-N April 19, 2012

4 Derating YAS5-24-N YAS5-48-N YAS5-5-W YAS5-24-N YAS5-48-N AS5-5-W Y Page 4 of 9 YAS5-12-W YAS5-12-W April 19, 2012

5 Derating YAS5-15-W YAS5-15-W Page 5 of 9 YAD5-5-N YAD NI YAD NI YAD5-5-N YAD NI YAD NI April 19, 2012

6 Derating YAD5-05H12-NI YAD5-05H12-NI YAD5-05H15- NI YAD5-05H15- NI YAD5-5-W AD5-5-W Y Page 6 of 9 YAD5-12-W YAD5-12-W April 19, 2012

7 Derating YAD WI YAD WI YAD WI YAD WI YAD5-05H05- WI YAD5-05H05- WI Page 7 of 9 YAD5-05H12-WI YAD5-05H12-WI April 19, 2012

8 Derating YAT NI YAT NI YAT WI YAT WI Design Considerations Basic Connection Notes 1.The pins of LN lines should be connected to the AC power outlet. 2. Please refer the instruction followed for further information. 3. F1: fuser1:vdrc1:mlccc2: Electrolytic capacitor:22µf ~220µF low esr capacitor. Page 8 of 9 April 19, 2012

9 Recommended Layout No. Pad Design Airflow Direction Safety Electrical Recommendation & Notes Pad hole: 1.2mm, pad diameter including hole: 2.5 mm. The plastic case also is considered heat sink. Advised not to put flat surface down after mounted. Isolated module, care to the spacing between input and output. The Vin(-) and Vo(-) planes should be placed under of the module separately. Avoid routing sensitive signal or high disturbance AC signal under the module. Safety Consideration The module, as one component for the end user, should be installed into the equipment. It is required to meet safety requirements in the system design. To avoid fire and be protected when short circuit occurred, it is recommended that a fast blow fuse with rating no less than 1A(Inrush current suppression circuit is required for greater filter capacitance at input terminal, or it will result in the disoperation of the fuse.) Series and Parallel Operation The modules should not be paralleled directly to increase power, but they can be paralleled each other through o-ring switches or diodes. Make sure that every module s maximum load current should not exceed the rated current at anytime. The modules can operate in series. To prevent against start-up failure due to start up time difference, SBD with low voltage difference can be paralleled at the Contact Information Anhui Hesion Trading Co.,Ltd. Add: Room1001,Zheshang Business Mansion, No.103 Kexue Road, Hefei Anhui,China TEL: , FAX: alecz@ahhesion.com Backup:alecz@126.com Web: output pins(sbd negative terminal connect to the positive pin of the output) for each module. Delivery Package Information Package material is multiple wall corrugated with less than 10 9 Ω surface resistance; internal material is anti-static foam with less than10 5 Ω surface resistance. Tray capacity: 4 4=16 PCS/boxTray weight: 1.0kg~1.20kg; Carton capacity:8 16=128 PCS, Carton weight:8.5kg~10 kg Quality Statement The modules are manufactured in accordance with ISO 9001 system requirements, in compliant with YD/T , and are monitored 100% by auto-testing system, 100% burn in.the warranty for the modules is 2-year. Page 9 of 9 April 19, 2012