800W Programmable Single Output. 105% rated output power, Protection type: Constant current limit

Transcription

1 Fetures: Universl AC input / Full rnge Progrmmle output Voltge (0% ~ 05%) Progrmmle output Current (0% ~ 05%) Forced current shring t prllel opertion Constnt current limit Selectle +5V / 0.5A or +9V / 0.A uxiliry output Glol control vi RS Remote setting multiple PSU vi RS, RS485 & I²C Power OK signl Remote ON / OFF, Remote sense function Protection: OVP, OLP, OTP, Fn filure Output Input Protection Function Environment Sfety & EMC MODEL DC Voltge Rnge Rted Current Current Rnge Rted Power Ripple & Noise (Mx.) Voltge Adj. Rnge Voltge Tolernce Line Regultion Lod Regultion Setup, Rise Time Hold Up Time (Typ.) Voltge Rnge Frequency Rnge Power Fctor (Typ.) Efficiency (Typ.) AC Current (Typ.) Inrush Current (Typ.) Lekge Current Over Lod Over Voltge Over Temperture Auxiliry Power Note. Note. Note.4 ±5.0% Typicl djustment y potentiometer. (VR) ±.0% ±.0% ±.0% 800ms, 00ms t full lod 4ms / 0VAC t full lod 90 ~ 64VAC, 7 ~ 70VDC 47 ~ 6Hz 0.95 / 0VAC, 0.98 / 5VAC t full lod 89% 90% 9% 9% 9% 9% 9.A / 00VAC,.7A / 40VAC 0A / 5VAC, 60A / 0VAC 05% rted output power, Protection type: Constnt current limit 85 ±5 C detect on NTC, Protection type: Auto recovery fter temperture goes down Selectle +5V / 0.5A or +9V / 0.A uxiliry output Remote ON / OFF Control By externl switch Power OK Signl Output Voltge Trim Output Current Trim Prllel (Current Shring) Note.5 Open drin signl low when PSU turns on, Mx. sink current: 0mA, Mx. drin voltge: 40V. Adjustment of output voltge is etween 0 ~ 05% of rted output Adjustment of output current is etween 0 ~ 05% of rted output Plese refer to pge 5 Address Setting Up to 8 units cn e set using n ddress switch (sw), 0~7 Working Temp. Working Humidity -0 ~ +60 C (Refer to de-rting curve) 0 ~ 90% RH non-condensing Storge Temp. & Humidity -40 ~ +85 C, 0 ~ 95% RH Temp. Coefficient ±0.0% / C (0 ~ 50 C) Virtion 0 ~ 500Hz, G 0min. / cycle, period for 60min. ech long X, Y, Z xes Complince to IEC 68--6, IEC Sfety Stndrds Withstnd Voltge Note.7 Certified UL ; EN I/P-O/P: KVAC (44VDC), I/P-FG:.5KVAC (VDC), O/P-FG: 0.5KVAC (707VDC) Isoltion Resistnce I/P-O/P, I/P-FG, O/P-FG: 00M Ohms / 500VDC EMI Conduction & Rdition Certified EN 550; EN 604-; EN Power Hrmonic & Voltge Fluctution nd Flicker Certified EN ; EN Note.6 EMS Immunity MTBF Cooling Others Dimension (WxHxD) Note Pcking AE-800- V 66.7A 0 ~ 66.7A 800W 0mVp-p <.0mA / 40VAC Lod nd temperture control fn AE AE AE AE AE AE V 4V 0V 6V 48V 60V 5.4A.5A 6.7A.A 6.7A.4A 0 ~ 5.4A 0 ~.5A 0 ~ 6.7A 0 ~.A 0 ~ 6.7A 0 ~.4A 800W 800W 800W 800W 800W 800W 50mVp-p 40mVp-p 00mVp-p 60mVp-p 480mVp-p 600mVp-p Vrile OVP, 0 ± 7% Vout. Refer to VS OVP curve. Protection type: Ltch-style (Recovery fter reset AC power ON or inhiit) Certified EN 5504; EN 604-; EN ; IEC ,, 4, 5, 6, 8, K HRS Certified MIL-HDBK-7F 7x4x49 mm / 5.00x.6x9.80 inch.7kg; 6pcs /.kg / 0.55CUFT. All prmeters NOT specilly mentioned re mesured t 0VAC input, rted lod nd 5 C of mient temperture.. Ripple & noise re mesured t 0MHz of ndwidth y using " twisted pir-wire terminted with 0.uF & 47uF prllel cpcitor.. Tolernce: includes setup time tolernce, line regultion nd lod regultion. 4. De-rting my pply in low input voltge. Plese check the de-rting curve for more detils. 5. In prllel connection only one unit will operte if the totl output lod is less thn 5% of the rted power. 6. The power supply is considered component which will e instlled into finl equipment. The finl equipment must e re-confirmed tht it still meets EMC directives. 7. This test is done without enclosure: I/P-O/P 44VDC. If with enclosure: I/P-O/P VDC,I/P-FG:VDC, O/P-FG: 707VDC 9% 6//0

2 Mechnicl Drwings: Unit:mm / inch 4[.6] 49[9.80] -M4 L=.0[0.] mx. 7[5.00] CN Address Switch 74.0[.9] 64.0[.5] CN 4.0[0.55] 98.0[7.80] 7.0[.46] 6.9[.06] [0.8] 6-M4(Both Sides) L=.0[0.] mx. 5.0[0.98].5[0.45].0[8.70] 8.0[0.] Recommended screw length is mesured from the power supply surfce AC Input Terminl Pin No. Assignment Pin No. Assignment ACL ACN CN Function Description: Pin No Function Description Pin No. Function Description Remote sense (+) Positive output voltge Remote sense (-) Negtive output voltge Power OK Prllel opertion current shre Aux output setting Inhiit ON/OFF (-) Inhiit ON/OFF (+) +5V / 0.5A or +9V / 0.A Auxiliry power I Progrm V Progrm +5V / 0.5A or +9V / 0.A Auxiliry power Seril Clock used in the I C interfce Seril Dt used in the I C interfce +5V / 0.5A or +9V / 0.A Auxiliry power For RS Receiver function For RS Trnsmission function Mting Housing / Contct JST PHDR-4VS or equivlent JST SPHD-00T-P0.5 or equivlent 6//0

3 LED Sttus: Solid(Green) Solid(Ornge) Slow Blink(Green) Fst Blink(Red) Solid(Red) Slow Blink(Red) LED LED Signl Sttus Intermittent Blink(Red) Interlce Blink(Red) *Locl mode : Use / to control output current nd voltge. Remote mode : Use RS- or I²C commnd to control output current nd voltge. Power OK (Locl mode) Power OK (Remote mode) Power Stndy Over Voltge Protection ( OVP ) Over Lod Protection ( OLP ) Over Temperture Protection ( OTP ) Fn Filure Power Filure De-rting Curve: Lod V.S Temp. Lod V.S I/P Voltge T=5 C Lod (%) Lod (%) Amient Temperture ( C) CMD VS Output Curve: Input Voltge (Vc) VS OVP Curve: OVP 00% 96% 0% 4% To ensure the power supply output voltge nd current could e ccurtely djusted, plese mke sure to djust the output voltge nd current > 0% vs. the rted voltge nd current. (e.g. for 4V unit, plese djust the DC output voltge ove.4v to ensure ccurcy; sme pplies to the output current) V/K 0.5V 0.75V 4.5V 4.8V 0.75V (Output 6.5%) 4.5V (Output 00%) CN 4 CN Exteml Voltge (VDC) 4 Exteml Resistor (KΩ) I. II. III. CTRL IC ma I-Shrink MIN ma / A/D PWM IC ma 0R CTRL / CTRL 0~5Vdc IC ma / Power Supply Power Supply Power Supply VC=IC R R=5K 6//0

4 Remote ON/OFF: (A) Defult Setting (B) (C) KΩ SW OFF Power OFF sw ON Power ON (A) Using internl 5V uxiliry source KΩ Power Supply Power Supply Power Supply Ctrl (B) ON / OFF Control y NPN trnsistor Tr L H Ctrl Power OFF Power ON KΩ SW OFF Power OFF sw ON Power ON (C) Using externl voltge source Externl DC source (MAX=9V dc) Power OK Signl: *The grounding of "" power should e connected to "" port. If " V-" is connected s ing, mke sure to short the nd V- ports. *Plce n dditionl cpcitor to hve etter performnce of uxiliry power opertion. Open(Defult Setting) Short To 5V 9V * 470μF 6V. LOAD DC / DC 5V/0.5A or 9V/0.A nd P.OK Signl. Remote Sense. Locl Sense (Defult setting) CN 4 CN 4 Lod Lod, Compenstion Voltge < 0.5V 6//0 4

5 . Current Shring with Remote Sensing(Prllel Connection) Current Shring with Locl Sensing Plese connect pins together for current shring function Plese connect pins together for current shring function 6//0 5

6 Instlltion Instruction:. Mounting Directions - Recommended stndrd mounting methods: () () -M4 L=.0[0.] mx. -M4 L=.0[0.] mx. -M4 L=.0[0.] mx. Recommended screw length is mesured from the power supply surfce. Mounting Method - There re ventilting holes on the front nd ck side pnels, do not ostruct; llow 50mm t lest for ir flow. - Recommended the torque of mounting screw: M4 screw:.7n m (.0kgf cm) More thn 50mm More thn 50mm FAN Air flow FAN 6//0 6