1500W Programmable Single Output

Transcription

1 Fetures: Universl AC input / Full rnge Progrmmle output Voltge (0% ~ 105%) Progrmmle output Current (0% ~ 105%) Forced current shring t prllel opertion Refer to pg. 5 for connection digrm) Constnt current limit Selectle +5V / 0.5A or +9V / 0.3A uxiliry output Glol control vi RS Remote setting multiple PSU vi RS, RS485 & I²C Power OK signl Remote ON / OFF, Remote sense function Protection: OVP, OLP, OTP, Fn filure Built-in ctive PFC Function Output Input Protection Function Environment Others MODEL DC Voltge Rted Rted Current Current Rnge Rted Power Ripple & Noise (Mx.) Voltge Adj. Rnge Voltge Tolernce Current Tolernce Line Regultion Lod Regultion Setup, Rise Time Hold Up Time (Typ.) Voltge Rnge Frequency Rnge Power Fctor (Typ.) Efficiency (Mx.) AC Current (Mx.) Inrush Current (Typ.) Lekge Current Over Lod Over Voltge Over Temperture Auxiliry Power Remote ON / OFF Control Power OK Signl Output Voltge Trim Output Current Trim Working Temp. Working Humidity Storge Temp. & Humidity Temp. Coefficient Virtion EMS Immunity Cooling Dimension (WxHxD) Pcking 1500W Progrmmle Single Output Note. Note.3 Note.4 AE V 15A ±5.0% Typicl djustment y potentiometer. Vi V-Adj from PSU front pnel) ±.0% rted output voltge of single unit) ±1.0% ±1.0% 800ms, 100ms t full lod 14ms / 0VAC t full lod 90 ~ 64VAC, 17 ~ 370VDC 47 ~ 63Hz 105% rted output power Protection type: Constnt current limit 85 ± 5 C detect on NTC, Protection type: Auto recovery fter temperture goes down By externl switch Open drin signl low when PSU turns on, Mx. sink current: 0mA, Mx. drin voltge: 40V. Adjustment of output voltge is etween 0 ~ 105% of rted output Adjustment of output current is etween 0 ~ 105% of rted output -5 ~ +60 C (Refer to lod de-rting curve) 0 ~ 90% RH non-condensing -40 ~ +85 C, 10 ~ 95% RH ±0.0% / C (0 ~ 50 C) Lod nd temperture control fn AE AE AE AE AE AE V V 30V 36V 48V 60V 100A 6.5A 50A 41.7A 31.3A 5A 0 ~ 15A 0 ~ 100A 0 ~ 6.5A 0 ~ 50A 0 ~ 41.7A 0 ~ 31.3A 0 ~ 5A 1500W 1500W 1500W 1500W 1500W 1500W 1500W 150mVp-p 150mVp-p 0mVp-p 300mVp-p 360mVp-p 480mVp-p 600mVp-p 0.95 / 0VAC, 0.99 / 115VAC t ful lod 89% 90% 9% 9% 9% 9% 93% 18A / 115VAC, 9A / 0VAC 30A / 115VAC, 45A / 0VAC < 3.5mA / 0VAC 10 ~ 500Hz, G 10min. / 1cycle, period for 60min. ech long X, Y, Z xes Complince to IEC ; IEC Sfety Stndrds Withstnd Voltge Note.7 Certified UL ; EN I/P-O/P: 3KVAC (4VDC), I/P-FG: 1.5KVAC (11VDC), O/P-FG: 0.5KVAC (707VDC) Isoltion Resistnce I/P-O/P, I/P-FG, O/P-FG: 100M Ohms / 500VDC (5 C / 70% RH) Sfety & EMC EMI Conduction & Rdition Certified EN 5503 Power Hrmonic & Voltge Fluctution nd Flicker Certified EN ; EN Note Note.6 ±3.0% rted output current of single unit) Prllel (Current Shring) Note.5 Plese refer to pge 5 Vrile OVP Refer to VS OVP curve.(ovp Tolernce 7%) Protection type: Ltch-style (Recovery fter reset AC power ON or inhiit) Selectle +5V / 0.5A or +9V / 0.3A uxiliry output Certified EN 550; IEC ,3,4,5,6,8,11 17x64x80 mm / 5.00x.5x11.0 inch.6kg; 6pcs / 16.6kg / 1.86CUFT 1. All prmeters NOT specilly mentioned re mesured t 0VAC input, rted lod nd 5 C of mient temperture.. Ripple & noise re mesured t 0MHz of ndwidth y using 1" twisted pir-wire terminted with 0.1uF & 47uF prllel cpcitor. 3. Tolernce: includes setup time tolernce, line regultion nd lod regultion. 4. De-rting my pply in low input voltge. Plese check the de-rting curve for more detils. 5. In prllel connection only one unit will operte if the totl output lod is less thn 5% of the rted power. 6. The power supply is considered component which will e instlled into finl equipment. The finl equipment must e re-confirmed tht it still meets EMC directives. 7. This test is done without enclosure: I/P-O/P 4VDC. If with enclosure: I/P-O/P 11VDC,I/P-FG:11VDC, O/P-FG: 707VDC 1

2 1500W Progrmmle Single Output Mechnicl Drwings: Unit:mm / inch 14.5[0.57] 80[11.0] 50.0[9.84] 15.0[0.59] 64[.5] 4-M4 L=3.0[0.1]mx. CN [3.86] 17[5.00] 313[1.3] 14.5[0.57] 34.0[1.34] 7.0[9.33] [1.38] 8-M4(Both Sides) L=3.0[0.1]mx. Recommended screw length is mesured from the power supply surfce AC Input Terminl Pin No. Assignment Pin No. L N Assignment ACL CAN CN Function Description: Pin No Function Description Pin No. Function Description Remote sense (+) Positive output voltge Remote sense (-) Negtive output voltge Power OK Prllel opertion current shre Aux output setting Inhiit ON/OFF (-) Inhiit ON/OFF (+) +5V / 0.5A or +9V / 0.3A Auxiliry power I Progrm V Progrm +5V / 0.5A or +9V / 0.3A Auxiliry power Seril Clock used in the I C interfce Seril Dt used in the I C interfce +5V / 0.5A or +9V / 0.3A Auxiliry power For RS Receiver function For RS Trnsmission function Mting Housing / Contct JST PHDR-VS or equivlent JST SPHD-00T-P0.5 or equivlent

3 LED Sttus: Solid(Green) Solid(Ornge) Slow Blink(Green) Fst Blink(Red) Solid(Red) Slow Blink(Red) LED LED Signl Sttus Intermittent Blink(Red) Interlce Blink(Red) 1500W Progrmmle Single Output Power OK (Locl mode) Power OK (Remote mode) Power Stndy Over Voltge Protection ( OVP ) Over Lod Protection ( OLP ) Over Temperture Protection ( OTP ) Fn Filure Power Filure *Locl mode : Use / to control output current nd voltge. Remote mode : Use RS- or I²C commnd to control output current nd voltge. De-rting Curve: Lod V.S Temp. Lod V.S I/P Voltge Lod (%) Lod (%) Amient Temperture ( C) CMD VS Output Curve: VS OVP Curve: Input Voltge (Vc) OVP 00% 196% 10% 114% To ensure the power supply output voltge nd current could e ccurtely djusted, plese mke sure to djust the output voltge nd current > 10% vs. the rted voltge nd current. (e.g. for V unit, plese djust the DC output voltge ove.4v to ensure ccurcy; sme pplies to the output current) V K 0.5V 0.75V 4.5V 4.8V 0.75V (Output 5%) 4.5V (Output 100%) CN CN CTRL I. II. III. IC 1mA I-Shrink MIN 1mA / A/D PWM IC 1mA 0R CTRL / CTRL 0~5Vdc IC 1mA / Power Supply Power Supply Power Supply R=5K 3

4 1500W Progrmmle Single Output Remote ON/OFF: (A) Defult Setting (B) (C) KO SW KO Tr Ctrl KO SW Externl DC source (MAX=9V dc) OFF Power OFF sw ON Power ON (A) Using internl 5V uxiliry source Ctrl L Power OFF H Power ON (B) ON / OFF Control y NPN trnsistor OFF Power OFF sw ON Power ON (C) Using externl voltge source * shown in ove digrm is referring to the of CN, not the ing from min power(neg-).* Power OK Signl & Auxiliry Power Setting: * The grounding of "" power nd P.OK signl should e connected to "" port. If " " is connected s ing, mke sure to short the nd ports. *Plce n dditionl cpcitor to hve etter performnce of uxiliry power opertion. Open drin signl low when PSU turns on, Mx. P.OK sink current: 0mA, Mx. drin voltge: 40V. 470 F 16V. LOAD Do NOT exceed 5V/0.5A or 9V/0.3A DC / DC 5V/0.5A or 9V/0.3A Open(Defult Setting) Short To 5V 9V nd P.OK Signl * shown in ove digrm is referring to the of CN, not the ing from min power(neg-).* 1. Remote Sense. Locl Sense (Defult setting) CN CN Lod Lod 1, Compenstion Voltge < 0.5V 4

5 1500W Progrmmle Single Output 3. Current Shring with Remote Sensing(Prllel Connection) Plese connect pins together for current shring function For Series connection, mke sure to isolte CN control signls 4. Current Shring with Locl Sensing Plese connect pins together for current shring function 5

6 1500W Progrmmle Single Output Instlltion Instruction: 1. Mounting Directions 1-1 Recommended stndrd mounting methods () () 4-M4 L=3.0[0.1]mx. 4-M4 L=3.0[0.1]mx. 4-M4 L=3.0[0.1]mx. 4-M4 L=3.0[0.1]mx. 4-M4 L=3.0[0.1]mx. Recommended screw length is mesured from the power supply surfce. Mounting Method -1 There re ventilting holes on the front nd ck side pnels, do not ostruct; llow 50mm t lest for ir flow. - Recommended the torque of mounting screw: M4 screw: 1.7N m (13.0kgf cm) More thn 50mm More thn 50mm FAN Air flow FAN 6