UNITY 2 TM. With ULTRA (50:50) & Air Server Series 2. Version 1.2. September 2012
|
|
- Helena Moody
- 5 years ago
- Views:
Transcription
1 UNITY 2 TM With (50:50) & Air Server Series 2 Version 1.2 September Installation for an system Switching between & Air Server :50 with UNITY 2 and Air Server series Switching between 50:50 / Air Server :50 with UNITY 2 and CIA QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 1
2 1. Installation for an system Arrange the instruments as shown. If the has a shorter link tube attached then the connection kit (U-UK2-2S) will be needed to reach from the to the UNITY 2 tube oven. To fit the longer link tube: Remove the white plastic thumb nuts highlighted. Then remove the back top cover. Remove the rear top side panel by pulling the back (narrow) edge of the panel sideways (away from the instrument) and then by pushing the panel up and sliding off. QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 2
3 Disconnect the two power leads from the link tube to the connector mounted near to the white plate above the heater. Disconnect the carrier gas inlet line of the link tube to the main carrier gas line of using 8 mm spanners. Using two spanners (10 mm and 8 mm) remove the short link tube from the heated. Fit the longer link tube to the heated and tighten. Note: it is essential to use both spanners when tightening this connection, use of only one spanner can result in twisting and subsequent damage. Reconnect the carrier gas inlet line. Attach the 2 power leads from the link tube to the connector (it does not matter which cable is connected into which hole). Replace the covers. QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 3
4 2. Switching between & Air Server Switch off power to UNITY 2 and. Connect the required link tube and move the other to one side as shown. Caution: The link tubes and tube oven can be hot. When switching configuration the MFC connections will also need reconfiguring according to the number of MFCs present. One MFC Using the supplied brass fittings and green PEEK tubing connect the MFC as shown. Switching s will require the MFC connections to be altered. (Remove T from vent in UltrA Mode) UTE-5045 long Stainless Split tube QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 4
5 Air Server Interface unheated Split tube Two MFCs Using the supplied brass fittings and green PEEK tubing connect the MFCs as shown. Switching s will not require the MFC connections to be altered. Note: If using a pump in Air Server the vents on both MFCs will need to be connected to the pump. UTE-5045 long Stainless Split tube QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 5
6 Air Server Interface unheated Split tube Switch on the power to the instruments and start the software. Go to View Options Configuration The Air Server and configurations are shown opposite. Ensure the correct Communication Port is selected for the. Restart the software. Air Server Air Server (3 channel) QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 6
7 Click on the Flow Control tab. Click Scan for Flow Controllers to automatically detect all MFCs present. Enter the maximum flow for the MFC(s) detected into the Full range ml/min box. Designate the flows to the MFC according to the setups shown above. One MFC Air Server UNITY Split & Trap UNITY Two MFCs Air Server and UNITY Split & UNITY Trap Restart the software. QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 7
8 3. 50:50 with UNITY 2 and Air Server series 2 The sample and recollection lines on 50:50 are long enough to reach the UNITY 2 tube oven over the Air Server, so do not require modification. To take advantage of the MFC(s) present on UNITY 2 with the 50:50 the following options are available: One MFC Using 2 sections of PEEK tubing and a 1/16 t-piece T the and recollect / dry purge flows on 50:50. 50:50 Do the same with the and desorb flows on UNITY 2. 1/8 graphite vespel ferrules recoll Note: In 50:50 the desorb flow is still manually controlled on UNITY 2 (the flow on UNITY 2 is not used). Set flow here A single MFC connection needs changing when switching s. Air Server recoll Interface unheated Split tube QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 8
9 Two MFCs 50 ) The flows on 50:50 are T d as above but the second MFC now controls the desorb flow on UNITY 2. Note: In 50:50 the flow on UNITY 2 is not used. No change to the MFC connections is needed when changing s. 50:50 1/8 graphite vespel ferrules recoll Air Server recoll Interface unheated Split tube Three MFCs QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 9
10 Now independently controlling the, desorb, re-collection and dry purge flow on 50:50. Note: In 50:50 the flow on UNITY 2 is not used. No change to the MFC connections is required when changing s. 50:50 1/8 graphite vespel ferrules recoll Air Server recoll Interface unheated Split tube QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 10
11 4. Switching between 50:50 / Air Server Switch on the power to the instruments and start the software. Go to View Options Configuration The Air Server and 50:50 configurations are shown opposite. Ensure the correct Communications port is selected for the 50:50. Restart the software. Air Server (3 channel) 50:50 Click on the Flow Control tab. Click Scan for Flow Controllers to automatically QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 11
12 detect all MFCs present. Enter the maximum flow for the MFC(s) detected into the Full range ml/min box. Designate the flows to the MFC: Air Server UNITY Split & Trap 50:50 a) 1 MFC Split & Recoll b) 2 MFCs Split & Recoll and UNITY Trap c) 3 MFCs Split, Recoll and UNITY Trap Restart the software. QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 12
13 5. 50:50 with UNITY 2 and CIA 8 One MFC Using 2 sections of PEEK tubing and a 1/16 t-piece T the and recollect / dry purge flows on 50:50. Do the same with the and desorb flows on UNITY 2. Note: In 50:50 the desorb flow is still manually controlled on UNITY 2 (the flow on UNITY 2 is not used). A single MFC connection needs changing when switching s. 50:50 1/8 graphite vespel ferrules Set flow here CIA 8 tube Two MFCs The flows on 50:50 are T d as above but the second MFC now controls the desorb flow on UNITY 2. Note: In 50:50 the flow on UNITY 2 is not used. 50:50 1/8 graphite vespel ferrules No change to the MFC connections is needed when changing s. QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 13
14 CIA 8 tube Three MFCs Now independently controlling the, desorb, re-collection and dry purge flow on 50:50. Note: In 50:50 the flow on UNITY 2 is not used. No change to the MFC connections is required when changing s. 1/8 graphite vespel ferrules 50:50 Air Server tube QUI-1045 UNITY 2 with (50:50) and Air Server Series 2 14
UNITY 2 TM. MFC Series 2 Installation Manual. Version 1.6 (Changes: Sections 1,2.1, 2.2, 3 & 4) June 2009
UNITY 2 TM MFC Series 2 Installation Manual Version 1.6 (Changes: Sections 1,2.1, 2.2, 3 & 4) June 2009 1. Introduction...2 2. Installation...5 2.1. UNITY 2...5 2.2. ULTRA 50:50...8 3. Software setup...11
More informationEncore XT Manual Gun Upgrade Kit
Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.
More informationMCH WIRE HARNESS WITH QUICK DISCONNECT REPLACEMENT Initial Release 1/31/2013
1. Table of Contents 1. Table of Contents Page 1 2. Remove Failed MCH-103.2 Page 1 3. Install MCH-103.2 to MCH-102NW Page 2 4. Install NC3FX-HD to MCH-103.2 Page 3 5. Install MCH-103.2 Battery Terminal
More informationSI-150-GIST. DART Thermo Quantiva, Endura, and Fusion VAPUR Interface User Manual. IonSense Inc. 999 Broadway Suite 404 Saugus, MA 01906
SI-150-GIST DART Thermo Quantiva, Endura, and Fusion VAPUR Interface User Manual Manual Revision 1 Document # 7.5.122 IonSense Inc. 999 Broadway Suite 404 Saugus, MA 01906 Copyright 2005-2015 by IonSense
More informationOperating Manual. GC-APPI Inferface for:
Operating Manual GC-APPI Inferface for: Q-Exactive TM MS, Exactive TM MS, and LTQ Orbitrap TM Series MS P/N: MC510000, P/N: MC511000, P/N: MC512000 Revision C GC-APPI-Interface 2016 MasCom Technologies
More informationSerial ATA Hot Swap Drive Cage Upgrade Kit for: Intel Server Chassis SC5200 Intel Server Chassis SC5250-E
Serial ATA Hot Swap Drive Cage Upgrade Kit for: Intel Server Chassis SC5200 Intel Server Chassis SC5250-E A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies/Products Order Number:
More informationOver. Year of Service. 2017/2018 Product Catalog. Chromatography. Research Supplies
Over 25 Year of Service 2017/2018 Product Catalog Chromatography Research Supplies Since 1991, Chromatography Research Supplies, Inc. (CRS) has become known worldwide as a leading manufacturer and innovator
More informationAgilent GC, MS, and ALS
Installation Checklist Verify Site Preparation for Your GC, GC/MS, and ALS 2 GC and MS Installation 2 Automatic Liquid Sampler (ALS) Installation 6 Acquisition Software and PC Installation 7 Performance
More informationBlue Box BLUE BOX TM LTD PARTS REPLACEMENT GUIDE
Blue Box BLUE BOX TM LTD PARTS REPLACEMENT GUIDE WARNINGS 1. All servicing should be performed by qualified service personnel. 2. WARNING, Battery may explode if mistreated. Do not recharge, disassemble
More informationASXPRESS PLUS Rapid Sample Introduction System Quick Installation Guide
ASXPRESS PLUS Rapid Sample Introduction System Quick Installation Guide Manual Part Number 610092 Rev 8 ASXPRESS PLUS Quick Installation Guide You can and should arrange for expert installation of the
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationH115i QUICK START GUIDE
TM Included Hardware Highlighted parts for Intel installation only A x8 LONG FAN SCREWS B x4 LGA 115X / 1366 STANDOFF C x4 LGA 2011/2011-3 STANDOFF F x8 D x4 AMD BLACK STANDOFF E x4 THUMBSCREWS G CORSAIR
More informationTo Our Valued Customers
To Our Valued Customers ADC s Adview Modular Diagnostic Station provides a truly customizable diagnostic medical instrument. With your purchase of an Adview unit that includes a thermometry module, you
More informationComplete Installation manual
VapoChill TM CPU Cooling System - LightSpeed [AC] TM asetek Inc. Complete Installation manual Date Version Comments 01-04-2004 1.0 1 Installing the VapoChill LightSpeed [AC] TM Preparing the case Step
More informationMotorola Atrix 4G Screen Replacement
Motorola Atrix 4G Screen Replacement Replace the screen of your Motorola Atrix 4G. Written By: Jake ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 INTRODUCTION Use this guide to replace the screen of the
More informationUpgrading a 2U CHP to an i7 Quad Core SBC
Upgrading a 2U CHP to an i7 Quad Core SBC 1. Parts required: i7 SBC Slim line SATA DVD drive Combined SATA data and power cable for slim-line optical drive Serial port ribbon cable - 9way D male to 10
More informationHD Flex Zero RU Cassette Holder and Bracket
HD Flex Zero RU Cassette Holder and Bracket Part Numbers: FLEX-0RUBR**, FLEX0RUCH** Panduit Corp. 2016 INSTALLATION INSTRUCTIONS The Zero RU Cassette Holder and Bracket are designed to mount on the side
More informationManual 04 - Logic Board
Manual 04 - Logic Board Written By: Josh Patterson 2017 guides.cellphonesandbox.com Page 1 of 16 TOOLS: Technician Starter Package (1) 2017 guides.cellphonesandbox.com Page 2 of 16 Step 1 Removal 1 - Battery
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationimac Intel 20" EMC 2105 and 2118 SSD
imac Intel 20" EMC 2105 and 2118 SSD Installation Replace the hard drive in your imac Intel 20" EMC 2105 and 2118. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 15 INTRODUCTION Upgrade your
More informationQUICK-START GUIDE. Quick Start Guide Temperature Controlled QCM Cell WHAT DOES GAMRY SOFTWARE DO?
www.gamry.com 1-215-682-9330 techsupport@gamry.com We have a variety of resources available to help you get started. Feel free to visit our website to find out more information on: Application Notes -
More informationLiebert XDA Air Flow Enhancer. User Manual
Liebert XDA Air Flow Enhancer User Manual Technical Support Site If you encounter any installation or operational issues with your product, check the pertinent section of this manual to see if the issue
More informationReplacing an Advanced Power and Cooling (APC) Unit
Replacing an Advanced Power and Cooling (APC) Unit You must replace a failed APC unit as quickly as possible (within minutes) to maintain correct airflow and cooling. Failed APC units can be hot-swapped.
More informationMac Mini Mid 2011 SSD Installation
Mac Mini Mid 2011 SSD Installation Replace your Mac Mini Mid 2011's hard drive for more storage space and an increase in speed. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 14 INTRODUCTION
More informationOracle <Insert Picture Here>
Slide 1 Oracle Slide 2 WZT-6509 version B Sun Fire Nehalem and Westmere Rack-Mount Server Installation and Replacement Welcome to the installation and replacement
More informationStar Trac Fitness E-ST 5090 Stepper. Install Guide
Star Trac Fitness E-ST 5090 Stepper Install Guide STAR TRAC E-ST STEPPER Install Guide E-ST 5090 E Series Stepper ASSEMBLY AND SETUP The following parts are included with the base STAR TRAC E-ST STEPPER:
More informationCharging Cabinet Owner s Manual
by edugear Charging Cabinet Owner s Manual Before using, please read these operating instructions carefully. They contain important advice concerning the use and safety of your Charging Cabinet. The Charging
More informationGas Cooling Accessory
TA Instruments 109 Lukens Drive New Castle, DE 19720 Thermal Analysis & Rheology A SUBSIDIARY OF WATERS CORPORATION Gas Cooling Accessory Operator's Manual PN 991426.001 Rev. D (Text and Binder) PN 991426.002
More informationWritten By: Adam Redmond
HTC One S USB Port Replacement This guide will show you how to remove and replace the USB port on your HTC One S. Written By: Adam Redmond ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION This
More informationReflowing Xbox 360 Motherboard
Reflowing Xbox 360 Motherboard Reflow the solder on your Xbox 360's motherboard. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 31 INTRODUCTION Use this guide to reflow the solder
More informationMac Mini Mid 2010 SSD Installation
Mac Mini Mid 2010 SSD Installation Replace your Mac Mini Mid 2010's hard drive for more storage space and an increase in speed. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 15 INTRODUCTION
More informationLumaRail Free Stand Bed Assist Rail with IntelliBrite LED Night Light
LumaRail Free Stand Bed Assist Rail with IntelliBrite LED Night Light Assembly and Operation Instructions Thank you for investing in this premium Platinum Health product. Please carefully follow the assembly
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationTo connect the AC adapter:
Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator
More informationFuser. Figure Remove the fuser assembly (1 of 2) 184 Chapter 5 Removal and replacement ENWW
Fuser 1. Remove the following assemblies. Scanner assembly. For the HP LaserJet 3015, see Scanner assembly. For the LaserJet 3020 and 3030, see Scanner assembly. Left cover. See Printer side covers. Rear
More informationRosemount 370XA Natural Gas Chromatograph
Quick Start Guide NGC-QSG-370XA February 018 Rosemount 370XA Natural Gas Chromatograph Quick Start Guide Typical Installation Minimum Specifications Safety First. Before You Start 1 3 370XA Natural Gas
More informationOven Loggermaster BEVS User Manual
Oven Loggermaster BEVS 2301 User Manual Version This manual shall be read carefully before starting. Directions included in this operation manual shall be strictly followed PAGE 1 Catalogue 1. Brief Introduction
More informationBondtech QR Installation guide for the BCN3D Sigma
Bondtech QR Installation guide for the BCN3D Sigma 1 Contents Introduction...3 List of tool required...3 Mechanical & Electrical Installation...4 Adjustment of steps/mm...12 2 Introduction This guide shows
More informationBrighton 6' series Greenhouse
Brighton ' series Greenhouse ssembly instructions Model HSP Model HSP Walk-in Greenhouse Statement ear Customer! May we congratulate you on your new Greenhouse. We feel sure that by following the detailed
More informationInstructions for SVC-KIT-0020
Kaleidescape, Inc. July 22, 2010 Instructions for SVC-KIT-0020 Title Time to complete 1U Server Power Supply Replacement 1 hour Procedure to complete Locate Parts and Tools Service Kit Parts Power supply
More informationInstalling the Server into a Rack
Installing the Server into a Rack Note These instructions apply to multiple models; illustrations may vary slightly. Rack Mount Kit Inventory Before installing the chassis on a standard 4-post rack, make
More informationFROG-4000TM Quick Start Guide
FROG-4000TM Quick Start Guide 1 Precautions DO NOT invert the instrument with the sparge bottle attached. DO NOT transport or store the instrument with liquid in the sparge bottle. DO NOT handle or carry
More informationAP-120 Series AP Mounting Kit
AP-120 Series AP Mounting Kit Installation Guide The AP-120 series mounting kit provides additional mounting options for the AP-120 series wireless access points. The mounting kit includes the following
More informationMicro GC Fusion Quick Start Guide
Micro GC Fusion - Quick Start Guide Micro GC Fusion Quick Start Guide 1 This quick start guide is designed to instruct the user on the steps required to install Micro GC Fusion and assumes the user is
More informationNDIR Infrared Gas Analyzer
QUICKSTART GUIDE MODEL 7600 Teledyne Analytical Instruments Quickstart Guide Teledyne Analytical Instruments Model 7600 Quickstart Guide GETTING STARTED This Quickstart Guide is designed to get you set
More informationOperating Instructions for FC Adjustable Fiber Optic Adapter
530 Main Street, Acton, MA 01720 Phone: (978)263-3584, Fax: (978)263-5086 Web Site: www.acton-research.com Operating Instructions for FC-446-020 Adjustable Fiber Optic Adapter Ver 2.0 Model FC-446-020
More informationMac Mini Mid 2011 SSD Dual Drive Installation
Mac Mini Mid 2011 SSD Dual Drive Installation Install a second hard drive in your mid 2011 Mac Mini. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 19 INTRODUCTION Use this guide to install
More informationHeat Containment System (HCS)
Heat Containment System (HCS) Revision Number 1 Wright Line LLC 160 Gold Star Boulevard Worcester, MA 01606 Tel: 800-225-7348 508-852-4300 Fax: 508-365-6178 www.wrightline.com info@wrightline.com All products
More informationPLATINblue MSQ Plus. Connection Guide V6951A UHPLC/HPLC. Mass spectrometry
PLATINblue MSQ Plus Connection Guide V6951A UHPLC/HPLC Mass spectrometry 3 Table of contents Note: For your own safety, be sure to read the manual and always observe the warnings and safety information
More informationStandard Operating Procedure
1 of 7 Prepared by: Reviewed by: Approved by: Date: Date: Date: The colored ink stamp indicates this is a controlled document. Absence of color indicates this copy is not controlled and will not receive
More informationMacBook Core 2 Duo Display Replacement
MacBook Core 2 Duo Display Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23 INTRODUCTION Change out the entire display assembly, including the inverter, Airport antennas, hinges
More informationQUICKSTART GUIDE. Infrared Gas Analyzer. Teledyne Analytical Instruments
QUICKSTART GUIDE MODEL 7500 Teledyne Analytical Instruments Quickstart Guide Teledyne Analytical Instruments Model 7500 Quickstart Guide GETTING STARTED This Quickstart Guide is designed to get you set
More informationWritten By: Walter Galan
imac Intel 17" Power Supply Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Power hungry? Keep those electrons flowing by replacing your power supply. TOOLS:
More informationMacBook Pro 13" Unibody Mid 2010 SSD Dual Drive Installation
MacBook Pro 13" Unibody Mid 2010 SSD Dual Drive Installation Use this guide to install a second SSD in place of the optical drive. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 13 INTRODUCTION
More informationWritten By: senordingdong
Installation of the UniMac V4 adapter into the Apple imac Intel 17". This enables the usage of non OEM LCD panels, and offers an otherwise unavailable Full HD upgrade. This used for repair of the common
More informationRemoving and Replacing Chassis Components
This chapter provides instructions on how to remove and replace components from the Cisco NCS 4016 chassis., on page 1 Removing a Line Card This section describes how to remove a line card from the Cisco
More informationBPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical
More informationINSTALLATION INSTRUCTIONS ECONOMIZER WITH EXHAUST
INSTALLATION INSTRUCTIONS ECONOMIZER WITH EXHAUST MODEL WGSEIFM-5 For Use with Bard 3 through 5 Ton Step Capacity Wall Mount Air Conditioners with Gas Heat Bard Manufacturing Company, Inc. Bryan, Ohio
More informationMac mini Late 2014 Power Supply Replacement
Mac mini Late 2014 Power Supply Replacement Replace the power supply in a Late 2014 Mac mini. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 19 INTRODUCTION Use this guide to replace
More information2-1. the ESI Probe Assembly. the PEEK Safety Sleeve and Sample Tube to the ESI Probe
You tune and calibrate your LCQ Advantage in ESI mode before you acquire data in either the ESI or the APCI mode. This chapter contains the following topics:.removing.connecting.installing.setting.setting
More informationMillenium Transformer Bundle. Instruction Manual
Millenium Transformer Bundle Instruction Manual 1 Taking Care of Your Digital Drum Set Thank you for purchasing this digital drum module. The drum module has been developed to act and play like a drum
More informationEaton Heat Containment System (HCS) Installation Guide
Eaton Heat Containment System (HCS) Installation Guide Copyright 2011 Eaton Corporation, Worcester, MA, USA. All rights reserved. Information in this document is subject to change without notice. No part
More informationPeel/Rewind Upgrade Kit
Peel/Rewind Upgrade Kit Installation Instructions This kit includes the parts and documentation necessary to install the Peel/Rewind upgrade kit on the following printers: ZM400 ZM600 Read these instructions
More informationTCM-4 Data Logger Battery Replacement Instructions
TCM-4 Data Logger Battery Replacement Instructions These instructions apply to the following product: TCM-4 Shallow Water Current Meter These instructions assume that the user has purchased a TCM-4 Battery
More informationElecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved
Introduction Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved The connectors furnishing high current to the KPA3 module have failed
More informationACQUITY UPLC Systems with 2D Technology Capabilities Guide
ACQUITY UPLC Systems with 2D Technology Capabilities Guide Revision A Copyright Waters Corporation 2012 All rights reserved Copyright notice 2012 WATERS CORPORATION. PRINTED IN THE UNITED STATES OF AMERICA
More informationSPECIAL INSTRUCTIONS FOR CAPACITORS COMPACT GENERATORS
SPECIAL INSTRUCTIONS FOR CAPACITORS COMPACT GENERATORS (WITH CAPACITOR CHARGER BOARD A3517-02) The process depends on Generator and System configuration. This document applies to installation of Capacitors
More informationMicroprocessor Module Replacement Kit for Multi-Zone Leak Monitors Instruction Manual
621 Hunt Valley Circle New Kensington, PA 15068 3015-5547 Tel: 724-334-5000 Revision 4 Fax: 724-334-5001 May 17, 2013 Microprocessor Module Replacement Kit for Multi-Zone Leak Monitors Instruction Manual
More informationCustomer Information. Service Engineer s Responsibilities. Additional Instruction Notes. System Information. Agilent Technologies
Thank you for purchasing an Agilent GC/MS system solution. This checklist is used by the installing engineer to ensure that the instrument and associated systems are correctly installed, upgraded and functioning
More informationMac mini Mid 2011 Hard Drive Replacement
Replace your Mac mini's Mid 2011 hard drive for more storage space. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION Use this guide to completely replace your mini's
More informationToshiba Satellite A210 Motherboard
Toshiba Satellite A210 Motherboard Replacement In this guide you will learn how to properly remove the Motherboard. Written By: Devin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Before
More informationUSER MANUAL INCLUDED IN THE BOX
USER MANUAL INCLUDED IN THE BOX Steering Motor Motor Cables Electronic Control Box Emergency Stop Button 3m USB cable Power Cord (UK, EU or US plug end) Additional Extras GT Steering Wheel - 6 x M5x16
More informationimac Intel 20" EMC 2105 and 2118 Hard Drive
imac Intel 20" EMC 2105 and 2118 Hard Drive Replacement Replace the hard drive in your imac Intel 20" EMC 2105 and 2118. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION
More informationInstallation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL)
Installation Guide for DV8 Off-Road Tailgate-Mounted Tire Carrier (18-19 Jeep Wrangler JL) Installation Time: 1 Hour Tools Required Trim removal tool (plastic or wood to prevent scratches on the paint)
More informationReplacing the Power Supply
APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools
More informationHuawei Ascend P6-U06 Screen/LCD Display Replacement
Huawei Ascend P6-U06 Screen/LCD Display Replacement Replace the Huawei Ascend P6-U06's screen and LCD display. Written By: Zachary Rose ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION Replace
More informationQuick Solutions Packet
Pub. No. J33039_EN 2008-11-15 Quick Solutions Packet ORTHO AutoVue Innova ORTHO AutoVue Ultra Topic No. Title 1 Interrupted Liquid Flow Error (ASPM255) 2 Replace the Air Filter 3 Defragment the Hard Drive
More informationANIxx. Installation Manual.
ANIxx Installation Manual www.audac.eu Introduction WaveDynamics Dante audio network interface The ANIxx are Dante audio network interfaces for use with WaveDynamics supporting amplifiers, supporting two
More informationMacBook Pro 15" Core 2 Duo Models A1226 and A1260 SSD Installation
MacBook Pro 15" Core 2 Duo Models A1226 and A1260 SSD Installation Written By: Dozuki System 2017 guides.crucial.com Page 1 of 10 INTRODUCTION You can install hard drives up to 9.5mm thick. Some drive
More informationCBT LW 4-PUMP ADD-ON INTERNATIONAL INSTALLATION GUIDE
CBT LW 4-PUMP ADD-ON INTERNATIONAL INSTALLATION GUIDE 2 General information This manual contains technical information regarding Bayer SeedGrowth Equipment. Please read and understand these instructions
More informationCisco TelePresence VX Clinical Assistant TM
Cisco TelePresence VX Clinical Assistant TM ACCESSORIES INSTALLATION GUIDE Drawer Module, PC Cabinet Module, PC Shelf, and Storage Pods...2 Laptop Shelf...3 Scope Hooks, WAP Mount, and Splash Cover...4
More informationCINTENNA ANTENNA REPAIR GUIDE
The Cintenna is a great tool when looking to transmit WIRELESS DMX data over obstacles or hard to reach places. Wireless DMX can have its issues when not having a good line of sight between the transmitter
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationMacBook Core Duo Optical Drive Replacement
MacBook Core Duo Optical Drive Replacement MacBook Core Duo optical drive replacement. Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION [video: http://www.youtube.com/watch?v=8l151w_giry]
More informationWritten By: Sam Lionheart
iphone 5c Front Panel Replacement Replace the Front Panel on your iphone 5c. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 INTRODUCTION For an easier repair, use our fix kit
More informationDell Alienware 13 R3 Heat-Sink Assembly
Dell Alienware 13 R3 Heat-Sink Assembly Replacement In this guide, we will show you how to remove and replace the Heat-Sink Assembly. Written By: Teren Wallace ifixit CC BY-NC-SA www.ifixit.com Page 1
More informationCryoFocus-4 GC Cryogenic Trap
CryoFocus-4 GC Cryogenic Trap Installation Guide CryoFocus-4 onto Shimadzu GC-2010 www.atasgl.com Disclaimer ATAS GL International B.V. makes no representations or warranties with respect to the contents
More informationSCSI Cable Installation Instructions
Identifying the SCSI Cable Parts SCSI Cable Installation Instructions for HP ProLiant DL100 Series Generation 2 Servers Item Description 1 Connector end 2 240 mm location 3 Terminator end Read instructions
More informationGateway Profile 4 service guide
Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................
More information3G Cell Modem Installation and User Guide
3G Cell Modem Installation and User Guide For BaseStation 1000 & BaseStation 3200 Irrigation Controllers in X and XS Cabinets April 24, 2017 Customer Service 1-866-294-5847 Baseline Inc. www.baselinesystems.com
More informationMacBook Core 2 Duo Optical Drive
MacBook Core 2 Duo Optical Drive Replacement Written By: Dozuki System 2017 guides.crucial.com Page 1 of 17 INTRODUCTION Upgrade or replace the combo or SuperDrive (requires a slim drive). TOOLS: Coin
More informationElecraft K3 KREF3 Output Level Modification
Elecraft K3 Revision A, September 15, 2015 Copyright 2015, Elecraft, Inc. All Rights Reserved Introduction This modification increases the output levels from the KREF3 Reference Oscillator to provide proper
More informationHow to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit
Instructional Video Series How to add a Second Drive to a Mac mini (2012) using the OWC Data Doubler SSD/2.5 Installation Kit Skill Level: Challenging Time to Complete: Approximately 45 Minutes Required
More informationXbox One X Project Scorpio Edition Motherboard Replacement
Xbox One X Project Scorpio Edition Motherboard Replacement This guide explains how to access the Motherboard of an Xbox One X Project Scorpio Edition manufactured by Microsoft in 2017. Written By: Ashley
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationFISCHER MINIMAX TM SERIES
TECHNICAL SPECIFICATIONS FISCHER TM SERIES Fischer Connectors SA All rights reserved Web version 1.0-03.2016 Changes without prior notice FISCHER TM SERIES KEY FEATURES The Fischer MiniMax Series increases
More informationiphone 7 LCD Screen and Digitizer Replacement
iphone 7 LCD Screen and Digitizer Replacement Fix a broken screen on an iphone 7 by replacing just the bare front panel, a.k.a. screen + digitizer assembly. Written By: Evan Noronha ifixit CC BY-NC-SA
More informationSeries 3000V Input/Output Board
Part E, Section 1 Model Voltage Pump Manifold Control This section covers the following unit configurations. All All All All Vista Standard (V) Vista Pattern (PC) E 1-0 E 1-1 Section E 1 WARNING: Allow
More informationBondtech QR Installation guide for the BCN3D Sigma
Bondtech QR Installation guide for the BCN3D Sigma 1 Contents Introduction... 3 List of tool required... 3 Mechanical & Electrical Installation... 4 Adjustment of steps/mm...12 Change Log: 1) Added comment
More informationInstallation and Maintenance
CHAPTER 4 Installation and Maintenance Revised: April 19, 2010, Introduction This chapter explains how to install a SCE 1000 platform in a rack or in a general tabletop or workbench installation. Additionally,
More information