Quick Solutions Packet
|
|
- Theresa Knight
- 6 years ago
- Views:
Transcription
1 Pub. No. J33039_EN Quick Solutions Packet ORTHO AutoVue Innova ORTHO AutoVue Ultra Topic No. Title 1 Interrupted Liquid Flow Error (ASPM255) 2 Replace the Air Filter 3 Defragment the Hard Drive 4 Format a DVD 5 Daily and Weekly DVD Backup 6 Manually Open the Cassette Drawer 7 AutoReader Initialisation Error (ASAR011) AutoReader Positioning Error (ASAR012)
2
3 INTERRUPTED LIQUID FLOW ERROR ASPM255 AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 1 OVERVIEW: ESTIMATED TIME: The pressure in the tanks is continuously monitored during aspiration of the saline and distilled water solutions. If a leak or an air intake occurs during aspiration the machine will sense a difference in pressure, which will generate error code ASPM minutes Determine which line is causing the error: 1. To determine which line is causing the error, perform 5 rinses with distilled water and 5 rinses with saline as follows: Select Maintenance. Select Flush. Select Execute. Select the Flush setup button on the right to choose saline or distilled water and to specify the number of cycles. Select OK. Select Continue. Note: This is not possible if the error code appears during initialisation. If the error code appears on the saline or distilled water line only, go to step 2. If the error refers to only one fluid line, perform steps 2 through 8 on that line. If the error refers to both fluid lines, perform steps 2 through 8 on both lines, and then perform the remaining steps. 2. Disconnect the two fluid Connectors from the line (distilled water or saline) showing the error on the left side of the machine. Make sure the male and female Connectors are not broken. Check that the Tubing is not pinched or pierced. Page 1 of 4
4 INTERRUPTED LIQUID FLOW ERROR ASPM Remove: The straight Tube from the Solution Tank. The White Block from the Tube. AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO Press the Check Valve of the yellow or red Connector (depending on the line) and shake the Tube to remove all traces of liquid. 5. Replace the White Block on the Tube. White Block 6. Reconnect the Connectors, matching the colors. 7. Replace the Tube in the Solution Tank. 8. Perform 5 rinses on the line. 9. Select Shutdown and turn off the analyser. Note: It is not necessary to turn off the computer 10. Make sure that the Pipette Tip is not obstructed by completing the following steps: Place the Probe over the Wash Station. Remove the right Connector from the Valve. Move the Connector up. If no liquid flows from the Pipette, replace it. Left Connector Right Connector Page 2 of 4
5 INTERRUPTED LIQUID FLOW ERROR ASPM Check for leaks at the Syringe and the Valve level (crystal or oxidation). If there is a leak: o Tighten the Clamp on the left Connector. AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 1 o Tighten the upper part of the Syringe. o Replace the Syringe on the lower part of the Syringe. Upper part of the Syringe Lower part of the Syringe 12. When the steps above are completed: Close all the doors. Turn on the analyser. Double-click on the AutoVue icon. Log in to initialise the system. If an error code is displayed, contact the OCD Customer Technical Support Center. For more information, contact the OCD Customer Technical Support Center. Page 3 of 4
6 INTERRUPTED LIQUID FLOW ERROR ASPM255 AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 1 Page 4 of 4
7 REPLACE THE AIR FILTER AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 2 OVERVIEW: REQUIRED SUPPLIES: ESTIMATED TIME: The Air Filter is located on the left side panel and is covered by a plastic grid. This filter purifies the air flowing through the Cassette Incubator and protects the fan located behind it from dust. Replace the filter when dirty. Filter (TEC ) and gloves 5 minutes 1. Turn off the analyser. 2. If necessary, remove the four (4) Screws, and pull the Grid out of the frame. 3. Remove the old filter and insert a new one. 4. Discard the used filter. Page 1 of 2
8 REPLACE THE AIR FILTER AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO Place the Grid back on the frame. If necessary, replace the four (4) Screws. 6. Press on the four corners of the Grid to ensure it is correctly set in place. 7. Turn on the analyzer. For more information, contact the OCD Customer Technical Support Center. Page 2 of 2
9 DEFRAGMENT THE HARD DRIVE AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 3 OVERVIEW: ESTIMATED TIME: Defragment the hard drive to optimize the arrangement of files and free space, which will improve system performance. From one to several hours, depending on the size of the disk, number of files, and system resources. 1. Close all applications including the AutoVue Innova/Ultra application and any antivirus software. Note: Do not perform a backup. 2. Click Start and select: All Programs Accessories System Tools Disk Defragmenter Page 1 of 4
10 DEFRAGMENT THE HARD DRIVE AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO On the Disk Defragmenter window, make sure the C: drive is highlighted and select Analyze. The Disk Defragmenter utility performs an analysis of your hard drive. When the analysis is complete, the Disk Defragmenter will either recommend that you defragment your hard drive, or that you postpone the defragment process. 4. If the recommendation is to defragment your hard drive, click Defragment. Page 2 of 4
11 DEFRAGMENT THE HARD DRIVE AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO The Disk Defragmenter window displays the progress of the defragmentation process. Note: The time required for defragmentation will vary depending on the size of the disk, the amount of data, and system resources. 6. When the process is complete, the Defragmentation Complete window will display. To view the defragmentation report, select View Report. To close the window, select Close. 7. Double-click on the AutoVue Innova/Ultra icon to launch the application. 8. Enter the password to initialise the analyser. For more information, contact the OCD Customer Technical Support Center. Page 3 of 4
12 DEFRAGMENT THE HARD DRIVE AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 3 Page 4 of 4
13 FORMAT A DVD AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 4 OVERVIEW: REQUIRED SUPPLIES: ESTIMATED TIME: Backup DVDs must be properly formatted before use. It may be necessary to format the DVD again if the DVD drive no longer recognizes it. DVD RW 30 minutes 1. During the formatting process, the instrument must not be in use. Verify that no sample is in the profile in progress status before you begin to format the DVD (e.g. blue arrow in the status column next to the profile). 2. Insert a new DVD in the DVD burner. 3. Minimize the AutoVue Innova/Ultra application. 4. Select the Menu icon from the Roxio box and drag it to the disc screen. 5. Select Format Disc. Page 1 of 2
14 FORMAT A DVD AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO Enter the DVD name into the Volume Label field as follows: MONDAY for Monday s DVD TUESDAY for Tuesday s DVD WEDNESDAY for Wednesday s DVD THURSDAY for Thursday s DVD FRIDAY for Friday s DVD SATURDAY for Saturday s DVD SUNDAY for Sunday s DVD AAAA-1 for the first six-month period (e.g ) AAAA-2 for the second six-month period (e.g ) 7. Select the Full Format button. 8. Click OK. 9. Click Yes in the Disc Preparation Needed window. Once formatting is complete, a window appears displaying the name of the DVD. 10. Click the arrow icon in the bottom-right corner of the Roxio box to eject the DVD. 11. Select the maximize arrow to continue with the application. For more information, contact the OCD Customer Technical Support Center. Page 2 of 2
15 DAILY AND WEEKLY DVD BACKUP AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 5 OVERVIEW: REQUIRED SUPPLIES: ESTIMATED TIME: Use the AV2G (AutoVue Second Generation) Backup Setup window to schedule daily backups. Display the Backup Setup window by right-clicking on the backup icon and selecting Setup. Choose a time when the instrument will typically not be processing samples. If you choose to create DVD backups, a popup message displays at the scheduled time prompting you to insert the correct DVD in the DVD drive. Formatted DVD RW (-RW or +RW) for each day of the week 5 minutes 1. Minimize the AutoVue Innova/Ultra software, and insert the appropriate DVD in the DVD drive. Backup icon 2. When the Day appears in the Roxio box, click OK. The backup icon on the task bar (bottom right of screen) changes from multi-colored to green during backup. When the backup is complete, the icon changes back to multi-colored and the system displays the log file. 3. To view the log file at any time, right-click on the multicolored backup icon and select View Log File. The Backup Log displays, showing the date, time, and status of backup attempts. 4. To see any notes, click on the.txt link to view the full file. If the system has been unsuccessful, an explanation appears at the bottom of the.txt file. This information should be communicated to the OCD Customer Technical Support Center. 5. After the backup is complete, right-click the Roxio box and select Eject Disc. Page 1 of 2
16 DAILY AND WEEKLY DVD BACKUP AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 5 Failure of Daily Backup Overview: The log file appears on the screen indicating that the daily backup was not successful. Required Supplies: Formatted DVD RW (-RW or +RW) for each day of the week Estimated Time: Two minutes To perform the Daily Backup again: Right-click on the multicolored backup icon and select Perform Daily Backup. Place the appropriate DVD into the drive. Wait for the current title to appear in the Roxio box. Click OK. o The backup icon changes from multi-colored to green during backup. The icon changes back to multi-colored when the backup is complete. If the daily backup is not successful, contact the OCD Customer Technical Support Center. Weekly Archive Backup Overview: On Tuesday, the daily backup system prompts for the Archive backup DVD (e.g., ). Required Supplies: Appropriate archive backup DVD Estimated Time: Two minutes To perform the Weekly Archive Backup: Place the appropriate DVD into the drive. Wait for the current title to appear in the Roxio box (e.g ). Click OK. o The backup icon changes from multi-colored to green during backup. The icon changes back to multi-colored when the backup is complete. Failure of Weekly Archive Backup Overview: The log file appears on the screen indicating that the archive backup was unsuccessful. Required Supplies: Appropriate archive backup DVD Estimated Time: Two minutes To perform the Archive Backup again: Right-click on the multicolored backup icon and select Perform Archive Backup. Place the appropriate DVD into the drive. Wait for the current title to appear in the Roxio box. Click OK. o The backup icon changes from multi-colored to green during backup. The icon changes back to multi-colored when the backup is complete. If the archive backup is not successful, contact the OCD Customer Technical Support Center. For more information, contact the OCD Customer Technical Support Center. Page 2 of 2
17 Manually Open the Cassette Drawer AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 6 OVERVIEW: TOOLS: ESTIMATED TIME: You may occasionally find it necessary to open the Cassette Drawer manually. This may happen if the solenoid fails, or a jam or blockage occurs, or the Cassette Drawer remains closed after the analyser is turned off. To manually open the drawer you must press the Cassette Drawer manual release switch. This is a metal tab located toward the rear of the instrument in the gap between the Casunca and the AutoRotor. Note: It is not necessary to turn off the instrument to perform this procedure. A wooden dowel or other narrow, non-conductive (non-metallic) device, such as a wooden or plastic ruler or a cassette liner box, and gloves 5 minutes 1. Open the Main Door. 2. Extend a suitable non-conductive tool through the gap between the Casunca and the AutoRotor. Cassette Drawer Manual Release Switch 3. Press the metal switch (silver tab) to open the Cassette Drawer. Caution: Be careful not to damage or dislodge the Cassette Barcode Reader Cable, positioned near the release switch. AutoRotor Casunca 4. Remove any blockage. 5. Check that the cassette sleeves and biocards are correctly loaded. 6. Close the Cassette Drawer. Important: You MUST reinitialise the system after you close the Cassette Drawer to continue inventory. Cassette Drawer Manual Release Switch Cassette Barcode Reader Cable Note: To avoid damaging the instrument, do not use this method to apply pressure to any other part of the analyser. For more information, contact the OCD Customer Technical Support Center. Page 1 of 2
18 Manually Open the Cassette Drawer AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 6 Page 2 of 2
19 AUTOREADER INITIALISATION ERROR ASAR011 AUTOREADER POSITIONING ERROR ASAR012 AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 7 OVERVIEW: REQUIRED SUPPLIES: ESTIMATED TIME: These errors can result from poor positioning of the AutoReader Shuttle, due to a jammed cassette or faulty alignment. Allen Key; compressed air; and soft cloth 20 minutes 1. Touch Shutdown. 2. Turn off the analyser. Note: It is not necessary to turn off the PC. 3. Open the Main Door and Waste Door. Pull out the 2 doorstops for the Waste Door and 1 doorstop for the Main Door on the inside of the upper frame (see picture). Turn them ¼ turn counterclockwise. 4. Manually move the Gripper to the left. Note: When moving the Gripper, be careful not to damage the teeth. 5. Push the Main Door and Waste Door to the left. 6. Remove the Cassette Waste Bin. 7. Remove the 3 Screws (circled in picture at right) on the top of the AutoReader Cover. 8. Remove the AutoReader Cover. Page 1 of 4
20 AUTOREADER INITIALISATION ERROR ASAR011 AUTOREADER POSITIONING ERROR ASAR012 AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO Check whether there is a jammed cassette in the AutoReader Shuttle or in the AutoRotor. If you find a jam, remove it. 10. Blow compressed air on the right Sensor. 11. Blow compressed air on the left Sensor. Page 2 of 4
21 AUTOREADER INITIALISATION ERROR ASAR011 AUTOREADER POSITIONING ERROR ASAR When the troubleshooting steps above are completed: Place the AutoReader Cover back in position and replace the 3 Screws. Place the cassette Waste Bin back in the instrument. Replace and lock the 3 doorstops. Place the Main Door and Waste Door back in the instrument. Place the Gripper on the metallic plate above the Centrifuge. AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO To continue: Close all of the doors. Power on the analyser. Double-click on the AutoVue icon. Log in to initialise the system. For more information, contact the OCD Customer Technical Support Center. Page 3 of 4
22 AUTOREADER INITIALISATION ERROR ASAR011 AUTOREADER POSITIONING ERROR ASAR012 AUTOVUE INNOVA/ULTRA QUICK SOLUTION NO. 7 Page 4 of 4
GEMINI. Compact Microplate Processor. System Guide
GEMINI Compact Microplate Processor System Guide 1 Gemini System Guide Table of Contents 1. Introduction 3 2. User Levels 4 3. Instrument Components & Accessories 6 4. Basic Operation - Quick Guide: 1-Lane
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationSymBiot I Sample Workstation
SymBiot I Sample Workstation Getting Started Guide DRAFT August 28, 2001 8:42 pm Symbfmgs.fm5 Copyright 1997, 2001, Applied Biosystems. All rights reserved. For Research Use Only. Not for use in diagnostic
More informationOwner s s Manual. G5 SATA Double Drive Internal Mounting Kit. Apple Macintosh G5. Add 2 SATA drives to the G5
Owner s s Manual Add 2 SATA drives to the G5 G5 SATA Double Drive Internal Mounting Kit Apple Macintosh G5 SATA (Serial ATA) 2 Internal Drive System Table of Contents User Guide Page How SATA (Serial ATA)
More informationUnpacking and Installing the Flora 2512 UV Printer. Steps 1: Unscrew the 10mm bolts holding the top. Then remove the top and put in a safe place.
Unpacking and Installing the Flora 2512 UV Printer Steps 1: Unscrew the 10mm bolts holding the top. Then remove the top and put in a safe place. Step 2: Unscrew 10mm bolts holding the end panels. On the
More informationView a Students Schedule Through Student Services Trigger:
Department Responsibility/Role File Name Version Document Generation Date 6/10/2007 Date Modified 6/10/2007 Last Changed by Status View a Students Schedule Through Student Services_BUSPROC View a Students
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationSetting up an Intermec PM43 printer with InterDriver version M-0 or newer
Setting up an Intermec PM43 printer with InterDriver version 7.3.5 M-0 or newer Setting up a bar code printer with 7.3.5 M-0 Intermec drivers or newer 1 INITIAL PRINTER CONFIGURATION When the printer is
More informationIssued by: LABORATORY MANAGER Original Date: March 14, 2001 Approved by: Laboratory Director Revision Date: June 6, 2003.
Policy # MI/SER/06/v01 Page 1 of 5 Section: Subject Title: Epstein Barr Virus Serology Issued by: LABORATORY MANAGER Original Date: March 14, 2001 Approved by: Laboratory Director Revision Date: June 6,
More informationBioRobot 9604 Operating Procedure
BioRobot 9604 Operating Procedure Note: An import table (directions given in number 20) must be made prior to a robot run. 1. Prior to operating the BioRobot 9604, perform all daily and weekly maintenance
More information02/12/2015 TIMS & TDRS SYSTEM MAINTENANCE GUIDE
SCOPE: The following is a recommended preventive maintenance guide to assure TIMS & TDRS systems run as smoothly as possible. As TIMS& TDRS are Windows 7 based PC s, preventive maintenance is typical of
More informationMachine Starters Kit
Machine Starters Kit Spitfire 65/90 Extreme Dear Customer, Thank you for buying a Mutoh Spitfire 65/90 Extreme series Printer. This kit contains some tools to make your printer operative. Please refer
More informationExpected Configuration. Connecting the TL-One to the Digital Video Creator 80
Overview This document describes how to transfer video clips from a TL-One Digital Video Recorder (DVR) to a Personal Computer (PC) using the Dazzle Digital Video Creator 80. The clips can then be written
More informationField Update Guide. for Raven Viper Pro
Field Update Guide for Raven Viper Pro Introduction The field update kit (P/N 117-0171-467) is designed to allow the Raven Viper Pro to utilize the automatic power down feature without returning the console
More informationTABLE OF CONTENTS INTRODUCTION...1 DEVICE SETUP...4 SUPPORT RESOURCES...9
TABLE OF CONTENTS INTRODUCTION...1 1.1 Minimum System Requirements 1.2 Package Contents 1.3 About This Manual 1.4 Rear View 1.4.1 Rear Features 1.5 Usage Notes DEVICE SETUP...4 2.1 Quick Start 2.2 Assembly
More informationDatacard CR500 Instant Issuance System. User Reference Guide. July Rev B
Datacard CR500 Instant Issuance System User Reference Guide July 2015 527495-001 Rev B Datacard CR500 User Reference Guide The CR500 Instant Issuance System Contents The CR500 Instant Issuance System The
More informationRemoval and Installation 8
Removal and Installation 8 8 Introduction 8-2 Service Calibration Guide to Removal and Installation 8-4 Window 8-8 Covers and Trims 8-12 Rear Tray 8-31 Rear Cover 8-32 Media Lever 8-33 Media Lever Position
More informationManual. LC-16 system. LC-16 Inkjet Printer 1
Manual LC-16 system LC-16 Inkjet Printer 1 Index ENVIRONMENT. 3 OPERATOR S SAFETY 3 OPERATION SAFETY 3 PART 1 INSTALLATION AND PARAMETER SETTING 4 1) Preparing 4 2) Installation 4 3) Priming 4 4) Parameter
More informationSTANDARD OPERATING PROCEDURE
Document No: LAB/023/2 Page 1 of 7 Uncontrolled copy if not printed on yellow paper. Title: STANDARD OPERATING PROCEDURE Use of the Magtration System 8Lx Document No: LAB/023 Version No: 2 CopyNo/Holder:
More informationOperating & Maintaining the Connex500/350 3-D Printer
Operating & Maintaining the Connex500/350 3-D Printer Starting the Connex Printer... 2 Loading Model and Support Cartridges... 4 Producing Models... 5 Printer Interface Color Key... 7 Printing Indicators...
More informationMachine Starters Kit
Machine Starters Kit Océ CS9000 Eco-Solvent printer series Dear Customer, Thank you for buying an Océ CS9000 Eco-Solvent printer series. This kit contains some tools to make your printer operative. Please
More informationFull User Manual and Quick Start Guide
Full User Manual and Quick Start Guide 2 W hile every precaution has been taken in the preparation of this manual, we assume no responsibility for errors or omissions. Neither, is any liability assumed
More informationInstalling imac Intel 27" EMC 2390 Dual HDD or
Installing imac Intel 27" EMC 2390 Dual HDD or SSD Drive Installing a secondary HDD or SSD in the mid 2010 27" imac EMC 2390. Written By: Brett Hartt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23 INTRODUCTION
More informationMagnetic Immunoassay Reader Operator Manual
Page 1 of 8 Magnetic Immunoassay Reader Operator Manual Table of contents 1 Introduction...1 2 Magnetic Immunoassay Reader...1 2.1 Contact information and spare parts...1 3 Contents of delivery...1 4 Technical
More informationInstruction manual of the controller unit. PCS ph-redox-chlorine-temp PCS ph-oxygen-temp PCS ph-redox-temp
Instruction manual of the controller unit PCS ph-redox-chlorine-temp PCS ph-oxygen-temp PCS ph-redox-temp SPIS TREŚCI GENERAL INFORMATIONS... 3 Main Functions... 3 Unit Specification... 3 Unit Dimensions......
More informationMontgomery County Community College Document Number: DP DeKalb Pike Revision Number: 2. Page 1 of 9 SOP: BioLogic LP Chromatography System
Page 1 of 9 Approvals Preparer: Jason McMillan Reviewer: Dr. Maggie Bryans Date: 18DEC14 Date: 18DEC14 1. Purpose: Operation of the BioLogic LP Chromatography System. 2. Scope: Applies to the BioLogic
More informationSpring Cleaning, Love Your Laptop, Computer Maintenance Call it what you want Its Important!
Spring Cleaning, Love Your Laptop, Computer Maintenance Call it what you want Its Important! Step 1 A clean computer is a happy computer. Do not allow crumbs or drinks to fall or spill onto the keyboard.
More informationVJ-1614 INSTALLATION MANUAL
VJ-6 INSTALLATION MANUAL Please read this manual before using Thank you for purchasing a MUTOH product. This manual explains the steps for unpacking, mounting and basic installation before using the MUTOH
More informationFingerprint Access Standalone User s Manual
Fingerprint Access Standalone User s Manual V1.1.1 1 Table of Contents 1 Overview... 1 2 Device Structure and Installation... 2 2.1 Device Structure... 2 2.2 Device Installation... 3 3 System Structure...
More information2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual
2015 SIMMCONN LABS, LLC. All rights reserved NewScope-T1 Operation Manual April 12, 2017 NewScope-T1 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1 Initial Inspection... 4 2.2 Installation
More informationMulti-Mount for Mac Pro to 5.25 Drive Bay Converter Bracket. Assembly & Installation Manual
Multi-Mount for Mac Pro 2009-2010 3.5 to 5.25 Drive Bay Converter Bracket Assembly & Installation Manual 1 INTRODUCTION 1.1 System Requirements 1.1.1 Computer Requirements 1.1.2 Hard Drive Requirements
More informationGateway Profile 4 service guide
Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................
More informationUser Manual Landscape Irrigation Controller
User Manual Landscape Irrigation Controller Drip Irrigation Micro Sprinklers Sprinklers Table of Contents Page 1 Introduction 2 2 About BERMAD BIC 1 Controller 2 3 Components Identification 2 4 LCD Display
More informationVisual Barcode Control
Visual Barcode Control For the Pocket PC Dynamic Control Software Visual Barcode for Windows Mobile Dynamic Control Software Dynamic Control Software Table of Contents Welcome Screen... 3 Software Load
More informationMicroprocessor Module Replacement Kit for Multi-Zone Leak Monitors Instruction Manual
621 Hunt Valley Circle New Kensington, PA 15068 3015-5547 Tel: 724-334-5000 Revision 4 Fax: 724-334-5001 May 17, 2013 Microprocessor Module Replacement Kit for Multi-Zone Leak Monitors Instruction Manual
More informationVJ-1604 INSTALLATION MANUAL
Please read this manual before using Thank you for purchasing a MUTOH product. This manual explains the steps for unpacking, mounting and basic installation before using the MUTOH Full-color inkjet printer
More informationMVPplus Quick Reference Guide
MVPplus Quick Reference Guide Use this guide to operate your printer on a daily basis. For more detailed information, refer to the User Guide. Contents External View...........................................................
More informationMulti-Mount for Mac Pro " to 5.25" Drive Bay Converter Bracket. Assembly & Installation Manual
Multi-Mount for Mac Pro 2009-2010 3.5" to 5.25" Drive Bay Converter Bracket Assembly & Installation Manual Introduction 1 INTRODUCTION 1.1 System Requirements 1.1.1 Computer Requirements 1.1.2 Hard Drive
More informationThermal Label Printer Guide
Thermal Label Printer Guide Thermal Printer 2844 A step-by-step guide to setting up your thermal printer TABLE OF CONTENTS Getting Started...1 Unpacking the Printer...2 Printer Features...3 Connecting
More informationTHUNDERBAY 4 MINI. Assembly Manual & User Guide
THUNDERBAY 4 MINI Assembly Manual & User Guide CONTENTS INTRODUCTION 1.1 Minimum System Requirements...1 1.1.1 Apple Mac Requirements 1.1.2 PC Requirements 1.1.3 Supported Drives 1.2 Package Contents...1
More informationVJ-1618 INSTALLATION MANUAL
Please read this manual before using Thank you for purchasing a MUTOH product. This manual explains the steps for unpacking, mounting and basic installation before using the MUTOH Full-color inkjet printer
More information6 Removal and replacement
6 Removal and replacement This chapter contains information about the following topics: Removal and replacement strategy User-replaceable parts Covers and external components Main assemblies Motors and
More informationUNITY 2 TM. With ULTRA (50:50) & Air Server Series 2. Version 1.2. September 2012
UNITY 2 TM With (50:50) & Air Server Series 2 Version 1.2 September 2012 1. Installation for an system...2 2. Switching between & Air Server...4 3. 50:50 with UNITY 2 and Air Server series 2...8 4. Switching
More informationVeritas Appliance Hardware Service Procedure
Veritas Appliance Hardware Service Procedure Replacing hard disk drives in a Primary Storage Shelf or an Expansion Storage Shelf Document Number: 137 Version: 3.2 (03/06/17) Purpose This document describes
More informationInstructions for How to Setup the Robot to Print
Instructions for How to Setup the Robot to Print Introduction This document provides guidelines for setting up a Pat O. Brown arrayer * to print antigens onto glass slides. Pat Brown s website, http://cmgm.stanford.edu/pbrown/mguide/index.html,
More informationicolumn 12 Operation Manual
icolumn 12 Operation Manual AccuBioMed Co., Ltd. 8F.-8, No.5, Wuquan 1st Rd., Xinzhuang Dist., New Taipei City 24892, Taiwan (R.O.C.) Tel: +886-2-2299-5989 Fax: +886-2-2299-2678 www.accubiomed.com AccuBioMed
More informationPLNVB26. OWNER S MANUAL Mobile Video System.
PLNVB26 OWNER S MANUAL Mobile Video System www.pyleaudio.com SAFETY INSTRUCTIONS Please read this section carefully and follow all the instructions given. This will help ensure reliable operation and extend
More informationapple Service Source Apple Cinema Display 22" LCD (ADC) 11 April Apple Computer, Inc. All rights reserved.
apple Service Source Apple Cinema Display 22" LCD (ADC) 11 April 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart Apple Cinema Display 22" LCD (ADC) 2003 Apple Computer,
More informationReplacement Keyswitch Assembly
Installation Instructions Replacement Keyswitch Assembly (Catalog No. 2711E-NKSW1) Applicable Terminals Use this replacement keyswitch with PanelView Terminals 2711-KA1, -KC1, -TA1, -TC1, -TA4, -TC4 and
More informationHARMONi G3. Quick Start Guide for HARMONi G3. imac Processor/FireWire Upgrade
HARMONi G3 imac Processor/FireWire Upgrade imac and Operating System Compatibility The HARMONi G3 imac processor/firewire upgrade is compatible only with imac 233, 266, and 333 MHz models (Revisions A-D);
More informationEtarmis. LITE User Guide
LITE User Guide Contents Creating A New Personal Record 3 Changing A Password 6 Creating a Site Administrator 7 Deleting An Employee 8 Making A Correction 10 Deleting A Correction 12 Modifying A Booking
More informationInstallation Manual for B8300 and Its Peripheral Devices
Installation Manual for B8300 and Its Peripheral Devices Finishing device Duplex/bypass device Finishing device To install the devices efficiently, follow the procedure below. Some peripheral devices may
More informationQuick Start Guide Ioline StudioJet
Quick Start Guide Ioline StudioJet User Notice Trademarks Ioline StudioJet is a trademark of Ioline Corporation. HP is a trademark of the Hewlett-Packard Company. Other product names, logos, designs, titles,
More informationBD FACSMelody Cell Sorter Quick Reference Guide
BD FACSMelody Cell Sorter Quick Reference Guide This guide contains instructions for using the BD FACSMelody cell sorter with BD FACSChorus software version. and later. Workflow Overview The following
More informationFast Facts. for Operating the scil Vet abc Plus. Hematology Chemistry Digital Radiography Ultrasound Orthopedics Education
Fast Facts for Operating the scil Vet abc Plus Hematology Chemistry Digital Radiography Ultrasound Orthopedics Education SCIL Vet ABC Plus Fast Facts Table of Contents Start Up Cycle pg. 2 Reagents Status
More informationHaze 800 DMX. User Guide. English
Haze 800 DMX User Guide English Introduction Box Contents Haze 800 DMX Remote Control (wired) User Guide Safety & Warranty Manual Support For the latest information about this product (documentation, technical
More information* IMPORTANT * REGISTERING YOUR MACHINE
* IMPORTANT * REGISTERING YOUR MACHINE Thank you for your purchase of the Keyline 994 Laser. Before continuing with machine setup and use, please complete the following; COMPLETE PRODUCT REGISTRATION FORM
More informationAppendix 1: DataStudio with ScienceWorkshop Sensors Tech Tips
Appendix 1: DataStudio with ScienceWorkshop Sensors Tech Tips Section 1: Starting an experiment 1.1 Opening a file 1. Open the File menu and select Open Activity. 2. In the Open dialog box, navigate to
More informationIf technical support is required, please contact Advent Technical Support at
Document 128-9011 Created 11/21/11 Kit Contents: Item # Qty. Component Description 1 2 Monitor Assembly 2 2 Remote Control 3 1 Cables # 3 4 1 Metal Wire Puller 5 1 Power Cord # 9 6 1 Owners Manual 7 2
More informationAgilent ICP-OES SVS 2 Productivity Package Installation and Upgrade Instructions
Agilent ICP-OES SVS 2 Productivity Package Installation and Upgrade Instructions NOTICE: This document contains references to Varian. Please note that Varian, Inc. is now part of Agilent Technologies.
More informationTroubleshooting. Chapter contents System Error Codes
Troubleshooting To better help our customers - this DesignJet T7100 series troubleshooting page is simply a guide / additional information for your convenience, as you search for assistance in repairing
More information2.0 Scope: This document is to be used by the DCS staff when administering the BMD measurement of the forearm to a participant.
Title: Bone Mineral Density by Dual-energy X-ray Absorption (DXA) - Forearm Measurement Version Date: 2014-JUL-10 Effective Date: 2014-OCT-15 Data Collection Site (DCS) Version: 2.1 Document Number: Number
More informationimac Intel 21.5" EMC 2389 Stand Replacement
imac Intel 21.5" EMC 2389 Stand Replacement Replace a broken or cosmetically unappealing stand on the imac 2389 21.5 Written By: Aaron Cooke ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION
More informationREMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.
REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right
More informationPreprocessing Methods for the Maxprep Liquid Handler Technical Manual
Preprocessing Methods for the Maxprep Liquid Handler Technical Manual Instructions for use of AS9100, AS9101, AS9200 and AS9201 TM529 11/17 Table of Contents 1 Description...1 2...2 2.1. Maxprep Liquid
More informationPortal Access Software Technical Manual
Portal Access Software Technical Manual Instructions for using the Portal Access Software with the Maxprep, Maxwell RSC and Maxwell RSC 48 Instruments TM549 Revised 1/19 Table of Contents 1 Description...1
More informationFuser. Figure Remove the fuser assembly (1 of 2) 184 Chapter 5 Removal and replacement ENWW
Fuser 1. Remove the following assemblies. Scanner assembly. For the HP LaserJet 3015, see Scanner assembly. For the LaserJet 3020 and 3030, see Scanner assembly. Left cover. See Printer side covers. Rear
More informationCreating a File and Folder Backup
Applicable Products These instructions apply to the following products: Barracuda Intronis Backup - MSP How to Create a Files and Folders Backup Before creating a files and folders backup set, make sure
More informationJKA multi-valve controller
JKA multi-valve controller manual JKA4.0 BEIJING KANGJIE ZHICHEN WATER TREATMENT CO.,LTD Shahe Industrial Zone, Changping District, Beijing, China, 102206 Tel: (+86) 010 69730336 Fax: (+86) 01080706936
More informationAgilent Technologies 16700B-Series Logic Analysis Systems. Installation Guide. Publication number November 2002
Installation Guide Publication number 16700-97023 November 2002 For Safety information and Regulatory information, see the pages behind the index. Copyright Agilent Technologies 2000-2002 All Rights Reserved
More informationBluelab ph Meter TM Instruction Manual
TM Instruction Manual www.getbluelab.com Table of Contents 1.0 Introduction to Bluelab ph Meter 2 2.0 Preparing the Bluelab ph Meter for use 3 3.0 Calibrating Meter 4 4.0 Measure ph Value 5 5.0 Cleaning
More informationThis tutorial was written by Team Xecuter. If you use anything from this tutorial please give credits and also a direct link to this page. Also if we have made any mistakes or left anything out please
More informationAssembly Manual & User Guide
Assembly Manual & User Guide TABLE OF CONTENTS 1. INTRODUCTION... 1 1.1 MINIMUM SYSTEM REQUIREMENTS 1.1.1 Apple Mac Requirements 1.1.2 PC Requirements 1.2 PACKAGE CONTENTS 1.3 ABOUT THIS MANUAL 1.4 FRONT
More informationX940e, X945e. Maintenance Guide
X940e, X945e Maintenance Guide July 2010 www.lexmark.com Contents...3 Storing supplies...3 Checking the status of supplies...3 Checking the status of supplies from the control panel... 3 Printing a menu
More informationimagine. print. create. Edible Printing Insights SET UP AND TROUBLE SHOOTING GUIDE
imagine. print. create. Edible Printing Insights SET UP AND TROUBLE SHOOTING GUIDE Warranty 1 Edible Printing System Warranty All printing systems are benefitted by a 12-month warranty that commences on
More informationSV Xchange. User Manual
SV Xchange User Manual Document Version 1.1 Dated 03 June 2009 Table of Contents Table of Contents... 1 General Description of the Sensor... 1 Which Manual do I Start With?... 1 Shipping and Receiving...
More information1. Review the printer safety information in the Regulatory Compliance document provided with your printer.
QUICK REFERENCE This Quick Reference contains supply loading information and general care and maintenance procedures for the Monarch Pathfinder Ultra Platinum 6039 printer. For more detailed information,
More informationNew Ricoh 1060 Copier. August 2004
New Ricoh 1060 Copier August 2004 Step By Step Turn Main Power Switch ON Press operation switch to make ON indicator light up You may turn just the operation switch off at night DO NOT turn main power
More informationOracle <Insert Picture Here>
Slide 1 Oracle Slide 2 WZT-6509 version B Sun Fire Nehalem and Westmere Rack-Mount Server Installation and Replacement Welcome to the installation and replacement
More informationBPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical
More informationMercury Elite Pro mini ASSEMBLY MANUAL & USER GUIDE
Mercury Elite Pro mini ASSEMBLY MANUAL & USER GUIDE TABLE OF CONTENTS 1. INTRODUCTION... 1 1.1 MINIMUM SYSTEM REQUIREMENTS 1.1.1 Mac Requirements 1.1.2 PC Requirements 1.2 PACKAGE CONTENTS 1.3 ABOUT THIS
More informationapple Service Source PowerBook G4 Updated 8 July Apple Computer, Inc. All rights reserved.
apple Service Source PowerBook G4 Updated 8 July 2003 2003 Apple Computer, Inc. All rights reserved. apple Service Source Take Apart PowerBook G4 2003 Apple Computer, Inc. All rights reserved. apple PowerBook
More informationScheduling WebEx Meetings with Microsoft Outlook
Scheduling WebEx Meetings with Microsoft Outlook About WebEx Integration to Outlook, page 1 Scheduling a WebEx Meeting from Microsoft Outlook, page 2 Starting a Scheduled Meeting from Microsoft Outlook,
More informationThe Olis Titrator Series
The Olis Titrator Series Perfect Titrations into any type of cuvette With considerable effort, one can do precise titration studies by hand. Or, one can let the OLIS titrators do the technician s work
More informationService & Maintenance
Service & Maintenance Internal Amplifier External (Peavey) Amplifier Core & HDD Monitor UPS Dollar Bill Acceptor Coin Mechanism Cleaning Fans & Filter G1-1 Internal Amplifier Amplifier Removal 1. Disconnect
More informationCncGcoder Models HD & HDx Manual
CncGcoder Models HD & HDx Manual Table of Contents WELCOME... 3 IN THE BOX... 4 Optional Accessories...4 HANDHELD OVERVIEW... 5 Overview...5 Charging the Battery...6 Turning On and Off...6 Plugging in
More informationR A D I O N I C S. READYKEY K6100 Readykey for Windows. User Guide. Logging In. Logging Out. If an ID device has been issued:
R A D I O N I C S READYKEY K6100 Readykey for Windows User Guide Logging In If an ID device has been issued: 1. Use your ID device with the desktop administration or Central Network Controller (CNC) reader,
More informationVersion 1.4 June 2018
1 Version 1.4 June 2018 Table Of Contents 1. Introduction 3 2. Unpacking the Instrument 4 2.1. Standard Accessories 2.2. Optional Accessories 3. Specifications 4 4. Installation 5 4.1. Quick 4-20 ma Start
More informationMoving your printer 1. Remove cables. Printing Moving the printer. Using color. Paper handling. 1 Turn the printer off. Maintenance.
Moving the printer Moving your printer 1 If you re going to move the printer, you must remove the supplies and attached options to prevent damage to the printer. Use the following steps to remove the options
More informationDATA DOUBLER. Apple Mac mini (2009)
DATA DOUBLER Apple Mac mini (2009) TABLE OF CONTENTS Introduction... 1 1.1 Hardware Compatibility 1.1.1 Host Computer Compatibility 1.1.2 Drive Compatibility 1.2 Package Contents 1.3 About This Manual
More informationPOCKET GUIDE ROUTINE MAINTENANCE, SAFETY, INSTALLATION & TROUBLESHOOTING
The 350 REFERENCE SERIES MULTI-PRICE TOTALISER POCKET GUIDE ROUTINE MAINTENANCE, SAFETY, INSTALLATION & TROUBLESHOOTING CashFlow CashFlow CashFlow C ashflow CashFlow CashFlow Cas hflow CashFlow CashFlow
More informationLASERJET ENTERPRISE M604, M605, M606
LASERJET ENTERPRISE M604, M605, M606 Maintenance kit replacement manual M604n M604dn M605x M605n M605dn M606x M606dn Conventions used in this guide TIP: Tips provide helpful hints or shortcuts. NOTE: Notes
More informationNanosight NS300 NBTC User Instructions
Nanosight NS300 NBTC User Instructions Preliminary notes: -The laser module is delicate and expensive. Handle it with care and do not leave it on the bench unattended. Only leave it in place in the instrument
More informationVISY-X. Technical Documentation. Subsequent installation of VISY-Density. Edition: Version: 2 Art. No.:
Technical Documentation VISY-X Subsequent installation of VISY-Density Edition: 2016-08 Version: 2 Art. No.: 350063 FAFNIR GmbH Schnackenburgallee 149 c 22525 Hamburg Tel.: +49 / 40 / 39 82 07 0 Fax: +49
More informationServicing and Maintenance
06/08 Rev. 4.05-01 USER MANUAL Servicing and Maintenance General Notes... 2 Servicing by trained personnel... 2 Safety... 2 Fault correction... 2 Ordering spare parts... 3 Servicing and cleaning... 4 Notes
More information9 Maintenance and Repair
Agilent 1200 Infinity II Series RID User Manual 9 Maintenance and Repair Introduction to Maintenance 120 Warnings and Cautions 121 Overview of Maintenance 123 Cleaning the Module 124 Storage of the Detector
More informationScheduling WebEx Meetings with Microsoft Outlook
Scheduling WebEx Meetings with Microsoft Outlook About WebEx Integration to Outlook, page 1 Scheduling a WebEx Meeting from Microsoft Outlook, page 2 Starting a Scheduled Meeting from Microsoft Outlook,
More informationReplacement Instructions
imac G5 Inverter, 20-inch Replacement Instructions Follow the instructions in this document carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note: Online
More informationInstructions to Install Retrofit Kit 6/7000 Machine
Instructions to Install Retrofit Kit 6/7000 Machine **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit kit contents: PART NAME QUANTITY PART NUMBER
More informationHard Drive, 20-inch. Replacement Instructions
apple imac G5 Hard Drive, 20-inch Replacement Instructions Follow the instructions in this document carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note:
More information