Supervisory Systems pcoweb card installation

Size: px

Start display at page:

Download "Supervisory Systems pcoweb card installation"

Erika Chapman
6 years ago
Views:

1 Supervisory Systems pcoweb card installation SNMP Modbus over IP BACnet over IP

SERIAL/MODEM SETTINGS Set the parameters as described (Chillers and Telecom units with MP20 terminal) (CRAC and

2 Unit side Serial settings configuration (pcoweb up to rel. 1.4.X) (CRAC units equipped with UG40 terminal) Press PRG button, Select SETTINGS MENU Type password Select SERIAL/MODEM SETTINGS Set the parameters as described (Chillers and Telecom units with MP20 terminal) (CRAC and Chiller units equipped with pco5 board) Press PRG button, Select SERVICE MENU Type password Select SERIAL/MODEM SETTINGS (BMS1) Set the parameters as described 2

3 Unit side Serial settings configuration (pcoweb from rel. 1.5.X) (CRAC units equipped with UG40 terminal) Press PRG button, Select SETTINGS MENU Type password Select SERIAL/MODEM SETTINGS Set the parameters as described (Chillers and Telecom units with MP20 terminal) Modbus in place of standard (CRAC and Chiller units equipped with pco5 board) Press PRG button, Select SERVICE MENU Type password Select SERIAL/MODEM SETTINGS (BMS1) Set the parameters as described 3

4 pcoweb: Installation 4

5 Connection with the pcoweb card Manual configuration with cross cable to the PC DIRECT CONNECTION WITH PC Automatic assignment of the IP address Pay attention to the unit reboot, necessary to fix the IP by means the MAC address DHCP 5

6 pcoweb: Configuration of the PC Manual configuration 6

7 pcoweb: Configuration of the PC Manual configuration 7

8 pcoweb: Configuration of the PC Manual configuration 8

pcoweb: Configuration of the PC Manual configuration It can be used for all BIOS versions and all pcoweb firmware versions Connect pcoweb to the Ethernet connector on the PC using a crossover cable;

9 pcoweb: Configuration of the PC Manual configuration It can be used for all BIOS versions and all pcoweb firmware versions Connect pcoweb to the Ethernet connector on the PC using a crossover cable; Immediately after reboot, as soon as the status LED remains on steady GREEN, hold pressed the black button; after around 20 seconds the status LED, due to the button being pressed, will return RED and flash slowly 3 times; the button must be released before the end of the 3 flashes; once the red flashes have terminated, the status LED will turn GREEN After that the status LED will start flashing => assigned 9

10 pcoweb: Configuration of the PC Manual configuration Without using black button ONLY for pco controller with BIOS > 5.18 and pcoweb > To press simultaneously «Alarm button + Enter button» of the UG40/50 Terminal pcoweb settings 10

11 pcoweb: Buttons and Leds 11

12 pcoweb: Leds meanings 12

13 pcoweb: Access to the pcoweb from the PC or other IP in case of configuration using DHCP 13

14 pcoweb: Default Home Page or other IP in case of configuration using DHCP GOOD!!! Web card correctly configured and now it s time to upload the Schneider Web Pages 14

15 pcoweb: Schneider Web Pages downloading /1 Click here Special pages follow the workflow of the special unit. separate sending 15

16 pcoweb: Schneider Web Pages downloading /2 16

17 pcoweb: Schneider Web Pages downloading /3 Example of containing parameters after registration 17

18 pcoweb: Schneider Web Pages downloading /4 18

19 pcoweb: Schneider Web Pages downloading /5 Identification of the proper web pages collection, Example: Business Line: Precision Air Conditioning Family: Uniflair_LE_Leonardo_Evolution Typology: Chilled Water Copy the folder in your desktop or other recipient 19

20 pcoweb: Schneider Web Pages UPLOADING /1 Download FTP FileZilla (free on google) or other FTP manager (trial version is enough). After that do enter the login parameters. Host: (default assignment) or other in case of DHCP mode Username: httpadmin Password: fhttpadmin 20

21 pcoweb: Schneider Web Pages UPLOADING /2 Copy and paste the content of CW in the pcoweb memory. Using Filezilla Same position of the html files and select overwrite all files I Possibility Copy and paste the content of CW in the pcoweb memory. Using FTP command Same position of the html files and select overwrite all files ftp://userid:pwd@ipaddress II Possibility 21

22 pcoweb: Schneider Web Page - OK Example: Leonardo CW Web Page with simulation of a Clogged Filter Alarm 22

23 pcoweb: Troubleshooting!!! If you face problems during the phases previously reported, please do check: 1. The protocol in the user terminal must be fixed on standard for SNMP / Modbus Over IP / BACnet Over IP 2. The serial speed in the user terminal must be fixed on The firewall must be disabled during configuration 4. The proxy server must be disabled during configuration 5. Manual IP assignment using CROSS cable 6. To access in the pcoweb reserved area: admin and fadmin 7. To access via FTP: IP defined, httpadmin & fhttpadmin 8. The WebPages must be inserted inside: usr/local/root/flash/http 23

pcoweb: IP change after manual configuration Example: In this case the IP: 172.16.0.

24 pcoweb: IP change after manual configuration Example: In this case the IP: has been changed with , not required in case of DHCP mode Good Job! Finished! 24

25 Supervisory Systems DDF import - StruxureWare/DCE console

Integration into DCE, StruxureWare console using Modbus/IP or SNMP The selection of the suitable DDF (web area previously indicated) is the result of these answers: 1. Family Name ex.

26 Integration into DCE, StruxureWare console using Modbus/IP or SNMP The selection of the suitable DDF (web area previously indicated) is the result of these answers: 1. Family Name ex. Uniflair_LE / Leonardo 2. Modbus/IP or SNMP ex. Modbus/IP Selection of the DDF uniflair_am_uniflair_le_amico_leonardo_ug40mp40_tcpip_modbus_ccu.xml 3. Import on DCE system (Catching of Analog values, status/alarm sensors, integer values via tcp/ip card) 26

27 StruxureWare Data Center Expert Import mask 27

28 StruxureWare DataCenter Expert Import mask it works! 28

29 Supervisory Systems Appendix

30 Ethernet network The Concept pcoweb 30

31 Example of network connection 31

32 pcoweb: Features and Options Board features: Power by pco Main Board ARM7 74MHz 16MB RAM, 8MB flash (32MB RAM, 16MB flash from release 3.0) Linux Protocols: HTTP (web pages 4MB) SNMP (Simple Network Management Protocol) Modbus over IP BACnet Ethernet ISO over ; BACnet/IP FTP server, FTP client The parameters configuration can be done automatically in case of DHCP servers 32

33 pcoweb: Functions available /1 WEB server: used to check or change the operating status of the pco controller using a remote computer running, for example, Internet Explorer or Mozilla Firefox; dynamic web pages developed by the user can be added; supports CGI technology; supports protection to access web pages; Logger: pcoweb can record the values of some of the pco controller variables in a file on its non-volatile memory: the file can then be downloaded to a PC using the browser; Graphs: Using the Logger function, the trends of the data saved over time can be viewed on graphs; pcoweb can send s when a programmable event occurs on the pco controller (activation of alarms, exceeding of thresholds) or at set time intervals; FTP push: pcoweb can send a file in XML format containing values of the variables; 33

34 pcoweb: Functions available /2 SNMPv1, v2, v3: to access pcoweb from a computer using supervision software based on the SNMP protocol. pcoweb can send programmable enterprise TRAP or INFORM packets for alarm notifications; TLS 1.2: available from release 3.0 Modbus over IP BACnet Ethernet ISO over : to access the pco controller using supervision software based on the BACnet Ethernet protocol; BACnet/IP: for access using supervision software based on the BACnet/IP protocol; FTP server: used to copy data files or web pages from/to pcoweb in a simple manner, using programs based on dragging icons from one window to another; DHCP: used to connect pcoweb to a local network using the method of automatic addresses assignment by a central server, rather than point to point addressing; DHCP is active by default. PLUGINS: used to add additional applications Firmware update: the pcoweb firmware can be updated from a computer 34

35 Supervisory Systems pcoweb card installation SNMP Modbus over IP BACnet over IP

pcoweb User manual I n t e g r a t e d C o n t r o l S o l u t i o n s & E n e r g y S a v i n g s

pcoweb User manual I n t e g r a t e d C o n t r o l S o l u t i o n s & E n e r g y S a v i n g s pcoweb User manual LEGGI E CONSERVA QUESTE ISTRUZIONI READ AND SAVE THESE INSTRUCTIONS I n t e g r a t e d C o n t r o l S o l u t i o n s & E n e r g y S a v i n g s WARNINGS CAREL bases the development