Olympus BX43_46 Installation Instruction (OEM Adjust) 4
|
|
- Eugene Richards
- 5 years ago
- Views:
Transcription
1 Olympus X_6 Installation Instruction (OEM djust) If you are not an experienced repair tech please consider the alternate (easy install) version dditional Items Included ut Not Shown: PN 07 Olympus X Illuminator ssy PN 077 Hex Key mm PN 060 Hex Key mm M VH tape PN 05 Pot-Plate-Cable ssembly PN 0 SHCS M x 0.7 x 0mm PN 07 Power Supply - XP Power 5V Fixed lade US Input/US Output PN 07 Cable ssy.5mm ID x.5mm OD R plug to US 6 foot The illuminator may be powered by plugging the cable into the power supply provided, or into a suitable US port on a computer or other device. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Power supplies are subject to substitution without notice due to availability issues and changes in regulations. Pot Knob (save original from microscope) Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) OF
2 Step : Place the microscope upside down, unplug the existing X illuminator cable, and unscrew the existing illuminator unit from microscope port as shown, using the mm hex key provided. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) OF
3 Step : Disassemble back cover. Note that after installation of the Nanodyne illuminator, there should be no power connections left in place to the DC power inlet (red circle). ** Safety and misc. ** The original illuminator circuitry (red arrow) is completely replaced by the Nanodyne equipment which is powered by a universal input wall plug power supply with low voltage DC output. Regardless whether the original circuitry is left in place or removed, be sure there is no possibility of electrical hazard in case an unfamiliar user connects power to the old DC input. The original circuitry may be left in place, or removed as it is no longer used. We recommend removing the power cable from the DC input connector. It should be cut short so there is no possibility it could be connected to the original circuitry, or insulated with heat shrink tubing or electrical tape. Han-Seung Yang //09 Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. PN 08 Olympus X_6 Illuminator System Installation (OEM djust) OF
4 Step : Pull out original pot cable from the existing cable ties (red circles). Unscrew using mm hex key and pull out the base unit as shown above. Step : Unscrew and pull out the base cover as shown in left. Han-Seung Yang //09 Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. PN 08 Olympus X_6 Illuminator System Installation (OEM djust) OF
5 Step 5: Lift up the iris diaphragm cover (it is taped as shown), unscrew and pull out the iris diaphragm unit, and remove another piece of taped cover from the base unit as shown in left. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) 5 OF
6 Step 6: Open the front panel, disconnect pot cable as shown, and remove the knob from the pot. Unscrew original PC panel as shown below. Save the screws. of them will be needed to attach the Nanodyne pot plate. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) 6 OF
7 Step 7: Remove the original PC panel and pot cable as shown above. Place Nanodyne Pot Plate Cable ssembly using of original screws, then reinstall original Pot Knob (saved from existing system) as shown below. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) 7 OF
8 Step 8: Cut small pieces of M VH tapes, attach to the back sides of the LIM and SET buttons, then put them back in the original places. They are now just used to cover the holes. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) 8 OF
9 Step 9: Reinstall front panel and secure the cables as shown above with the existing tie wraps, to keep the cables out of the moving parts of the microscope, and the optical path from the illuminator. Insert black rubber guide (red circle) to the right place and attach the original taped cover from the base unit as shown in left. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) 9 OF
10 Step 0: Reinstall the iris diaphragm unit using original hex screws as shown above and attach the original taped iris diaphragm cover as shown in left. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) 0 OF
11 Step : Insert and secure the base unit using original hex screws as shown above. Place the bottom cover and make sure all the original circuitry cables are disconnected (red circles) as shown in left. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) OF
12 Step : Reinstall the back cover, insert PN 0 hex screw (red circle) to the screw hole of the Nanodyne adapter as shown above, and insert Nanodyne illuminator unit to the microscope port. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) OF
13 Step : Tighten the hex screw to secure Nanodyne illuminator in place, connect the pot cable, and secure the cables as shown in left (using M VH tape if needed). Plug C adapter to the Nanodyne illuminator and now it is ready to use. *Note: The detailed Pot Cable insertion procedure to the TPI Main ssy will be shown in next page. Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Tape to secure wires. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) OF
14 efore Insertion Partial Insertion Connect the socket at the end of the Pot Cable ssembly to the mating socket of the illuminator, as shown in the pictures on this page. fter partially inserting the socket to the mating socket of the illuminator with your finger, use other mechanical tools such as driver or tweezer to firmly insert the socket all the way by pushing back edge of the socket as indicated with the red arrow in the image (top right). The socket cannot be fully engaged by pushing on the wire attached as the wires would just collapse. If you want to pull the socket out, pull the wire straight out by firmly gripping the black heat shrink tubing. Full Insertion Copyright 07 Nanodyne Measurement Systems. Document authorized for installation of Nanodyne equipment only. Han-Seung Yang //09 PN 08 Olympus X_6 Illuminator System Installation (OEM djust) OF
Olympus BX43 and BX46 Installation Instruction for Microscope End Users (easy install version) 4
Olympus X and X6 Installation Instruction for Microscope End Users (easy install version) PN 07 Olympus X_6 Illuminator ssy dditional Items Included ut Not Shown: PN 077 Hex Key mm PN 060 Hex Key mm M
More informationIncluded Items Not Shown:
PN 09 HP Illuminator ssy Olympus HS Installation Instructions - Nanodyne Illuminator for Olympus HS Microscope Figure. Parts included in Olympus HS Illuminator System. Included Items Not Shown: PN 057.5mm
More informationMicroscope with original illuminator. Microscope with Nanodyne replacement illuminator.
Nanodyne Replacement Illuminator for Zeiss xioskop Microscope Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Copyright 09 Nanodyne Measurement Systems. Document
More informationOriginal Zeiss Axiovert Illuminator. Nanodyne Replacement Illuminator for Zeiss Axiovert
Zeiss xiovert Replacement Instructions - Original and Nanodyne Replacement Original Zeiss xiovert Illuminator Nanodyne Replacement Illuminator for Zeiss xiovert Copyright 06 Nanodyne Measurement Systems.
More informationNanodyne Replacement Illuminator for Zeiss Axiovert Microscope Installation Instructions
Nanodyne Replacement Illuminator for Zeiss xiovert Microscope Installation Instructions Note that this photo shows an older version of the illuminator. The current version is shown on the sheet. Original
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationRichter Optica. Instructions for Model: HSX1 High School Microscope
Richter Optica info@richter-optica.com Instructions for Model: HSX1 High School Microscope Eyepiece 360 Rotatable Head Objectives Carrying Handle Revolving Nosepiece Rack Stop Slide Holder Focus Tension
More informationRichter Optica. Instructions for Model: MDS2 Middle School Microscope
Richter Optica info@richter-optica.com Instructions for Model: MDS2 Middle School Microscope Eyepiece 360 Rotatable Head Revolving Nosepiece Carrying Handle Objectives Rack Stop Stage Stage Clips Disc
More informationZ-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly
Replacing the LCD Cable To remove and replace the LCD Cable you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Socket wrench with 10mm socket Removing the Side Panel 1.
More informationSolid State Control Calibration Procedure MKG Solid State Griddles - All Options
Solid State Control Calibration Procedure MKG Solid State Griddles - All Options The following procedure describes the steps to calibrate the Solid State Temperature Control for any of the MKG-ST Griddle
More informationPlasma Panel Replacement Guide DU-42PX12X
Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be
More informationPowerFlex 400 Frame G and H Replacement Procedure for Gate Power Board
Service Bulletin PowerFlex 400 Frame G and H Replacement Procedure for Gate Power Board Contents This publication provides instructions for replacing the gate power board for PowerFlex 400 Frame G and
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationInstalling a Power over Ethernet injector
Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart
More informationHDMI Upgrade for the Showcase DVD
THE LEADER IN AUDIO ENGINEERING for the Showcase DVD INSTALLATION AND SETUP GUIDE Getting Started THERE ARE NO USER- SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT. Krell authorizes this HDMI upgrade to the
More informationSERIES 5 TABLES/BENCH
Wire Manager Driveshaft Driveshaft Cover Stretcher Power Cable Low-Voltage Cable Power Supply Master Motor (can be on either side) Controller Controller Cable Lifting Column Foot SERIES 5 TABLES/BENCH
More informationimac Intel 21.5" EMC 2389 Stand Replacement
imac Intel 21.5" EMC 2389 Stand Replacement Replace a broken or cosmetically unappealing stand on the imac 2389 21.5 Written By: Aaron Cooke ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION
More informationWritten By: Brittany K
Nintendo DS Lite Motherboard Replacement Written By: Brittany K ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION This guide has been updated by ifixit staff! Read the new, official guide here.
More informationPower Cable. Low-Voltage Cable
Troubleshooting Guide Power Cable Low-Voltage Cable Wire Manager Power Supply Driveshaft Driveshaft Cover Master Motor (can be on either side) Controller Controller Cable Lifting Column Foot Stretcher
More informationYamaha DX7 LCD Installation Guide
Table of Contents Required Tools/ Getting Started... p. 2 Installation... p.3-11 Opening the DX7... p. 3 Locating and Removing the LCD Bracket... p. 4 Removing the LCD Bezel Cover... p. 5 Removing the
More informationSP-100. Service Manual Aug. 02
SP-100 Service 2004. Aug. 02 1. Caution for maintenance and Service. Please take care below points when you do Service and Maintenance. (1) Service and Maintenance should be done under safety condition.
More informationCanon Powershot A70 Button Flex Assembly Replacement
Canon Powershot A70 Button Flex Assembly Replacement Written By: Brian ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION This guide will walk through the process of removing the button flex assembly
More informationMemory Expansion for DriveLogix Controller
Installation Instructions Memory Expansion for rivelogix ontroller!!! TTENTION: To avoid an electric shock hazard, verify that the voltage on the bus capacitors has discharged before performing any work
More informationUpgrading the programmer supply unit of the BeeProg+/BeeProg2 programmer
Upgrading the 50-0033 programmer supply unit of the BeeProg+/BeeProg2 programmer How-Do-It Manual December 2012 BeeProgX_50-0033_PSU1_upgrade_manual, version 1.31 page 1 Introduction This how-do-it manual
More informationIntel NUC Kit NUC8i7HNK & NUC8i7HVK User Guide. Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide
Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationWritten By: Walter Galan
imac Intel 21.5" EMC 2428 CPU Replacement Replace the CPU in your imac Intel 21.5" EMC 2428. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 33 INTRODUCTION Use this guide to upgrade
More informationElectronic Balance Ionizer STABLO-AP Service Manual
321-78209 Jan. 2016 Electronic Balance Ionizer STABLO-AP Service Manual Analytical & Measuring Instruments Division This page is intentionally left blank. Table of Contents 1. Precautions for Troubleshooting...
More informationReplacing the Power Supply
APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools
More informationUpgrading a 2U CHP to an i7 Quad Core SBC
Upgrading a 2U CHP to an i7 Quad Core SBC 1. Parts required: i7 SBC Slim line SATA DVD drive Combined SATA data and power cable for slim-line optical drive Serial port ribbon cable - 9way D male to 10
More informationIntel NUC Kit NUC8i7HNK & NUC8i7HVK User Guide. Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK. User Guide
Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationWritten By: Walter Galan
imac Intel 17" Power Supply Replacement Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 18 INTRODUCTION Power hungry? Keep those electrons flowing by replacing your power supply. TOOLS:
More informationRemoving the Battery. 2.Disassembly. Disassembly. Figure 1 Battery Removal. Removing the Battery 2-5
Removing the Battery. Turn the computer off, and turn it over.. Slide the latch in the direction of the arrow (Figure a.. Slide the latch in the direction of the arrow, and hold it in place (Figure a..
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationRSL PSM-2 Power Supply Module Project: Modifying a FlatCap2
RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2 Dear Do-It-Yourselfer, The stock FlatCap2 is less than a stellar performer. Used with a CD5 CD player, for example, it gives flabby bass control,
More informationToshiba Satellite A105-S4011 Touchpad
Toshiba Satellite A105-S4011 Touchpad Replacement This guide will instruct you on how to remove the current touchpad from this laptop and how to reinstall another. This is a straightforward process and
More informationToshiba Satellite A210 Fan Replacement
Toshiba Satellite A210 Fan Replacement In the guide you will learn how to remove the fan from the Toshiba Satellite A210. Written By: Youlen ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION Before
More informationMac Mini Mid 2010 SSD Installation
Mac Mini Mid 2010 SSD Installation Replace your Mac Mini Mid 2010's hard drive for more storage space and an increase in speed. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 15 INTRODUCTION
More informationV910 Kit. Hardware Installation Guide. P/N Revision: A
V910 Kit Hardware Installation Guide P/N 28935 Revision: A V910 Kit Hardware Installation Guide VeriFone, Inc. 2099 Gateway Place Suite 600 San Jose, CA 95110 Telephone: 408-232-7800 http://www.verifone.com
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More informationGPIB-232CT-A IBCL EPROM Installation Guide
NATIONAL INSTRUMENTS The Software is the Instrument Installation Guide GPIB-232CT-A IBCL EPROM Installation Guide This guide describes how to replace the factory-installed EPROM that comes with your GPIB-232CT-A.
More informationMotorola Moto Z2 Play Audio Jack Replacement
Motorola Moto Z2 Play Audio Jack Replacement How to replace your Moto Z2 Play's audio jack with this guide if you can't hear with headphone or if there are scratching noises. Written By: mitch miller ifixit
More informationASUS D550MA-DS01 Motherboard
ASUS D550MA-DS01 Motherboard Replacement This guide will show you how to remove the motherboard from the laptop. Steps included in this process are removing the screws, disconnecting cables, and removing
More informationCubePro. Main PCB Replacement Guide. Prosumer 3D Printer. Original Instructions
CubePro Prosumer 3D Printer Main PCB Replacement Guide Original Instructions 1 INTRODUCTION COPYRIGHT 2014 by All rights reserved. This document is subject to change without notice. This document is copyrighted
More informationFigure 4-29 Removing the CPU compartment cover
4 Replacement Procedures 4.9 CPU 4 4.9 CPU Removing the CPU To remove the CPU, follow the steps below. 1. Turn the computer upside down and remove two M2.5 4 security screws securing the CPU compartment
More informationToshiba Satellite A210 Motherboard
Toshiba Satellite A210 Motherboard Replacement In this guide you will learn how to properly remove the Motherboard. Written By: Devin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Before
More informationINSPECTION TOOL. Inspection Video Camera with Color LCD Monitor. EU Environmental Protection. Model: 8802LE,8803LE. Model: 8802LE,8803LE
INSPECTION TOOL Inspection Video Camera with Color LCD Monitor Model: 8802LE,8803LE EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle
More informationUpgrade Instructions. P/N Revision A. October Printer Terminal Holder * *
Upgrade Instructions P/N 96-08-0 Revision A October 000 480 Printer Terminal Holder P/N 96-08-0 Revision A *96080* Instructions This terminal holder connects the INTERMEC R 600 Series and 700 Series Computers
More informationWritten By: Sam Lionheart
iphone SE Display Assembly Replacement Replace the cracked or broken screen on your iphone SE. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Use this guide to replace
More informationView Wall Interface. Dynamic Glass INSTALLATION GUIDE. Description. System Requirements. Installation Overview
Description The solution is a compact, wall-mounted interface used for monitoring and changing the tint levels of View Dynamic Glass. The product leverages 802.11-based Wi-Fi technology for connectivity
More informationHuawei P9 Display Assembly with Frame Replacement
Huawei P9 Display Assembly with Frame Replacement Replace the display assembly including the frame in your Huawei P9 smartphone. Written By: Dominik Schnabelrauch ifixit CC BY-NC-SA www.ifixit.com Page
More informationEncore XT Manual Gun Upgrade Kit
Instruction Sheet P/N 1600823-01 Encore XT Manual Gun Upgrade Kit 1600834 Introduction Follow these instructions to upgrade your Encore manual spray gun to the improved design of the Encore XT spray gun.
More informationOMM200 and OMM200T. Metallurgical Microscope
OMM200 and OMM200T Metallurgical Microscope Instruction Manual (Please read the manual carefully before using the microscope) Contents Safety ----------------------------------------------------------------------------
More informationL-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGNOSTIC ADDENDUM
111 Canfield Avenue Randolph, New Jersey 07869 1-800-LANDICE FAX 973-927-0630 L-80 SERIES HOME & COMMERCIAL HIGH-TECH ENTERTAINMENT CENTER DIAGSTIC ADDENDUM High-Tech Entertainment Center Explosion Part
More informationSingle cable kit for the FCB1010
Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing
More informationXbox 360 Motherboard Replacement
Xbox 360 Motherboard Replacement Motherboard replacement. Redigido por: Walter Galan ifixit CC BY-NC-SA pt.ifixit.com Página 1 de 29 INTRODUÇÃO Use this guide to completely strip down your motherboard.
More informationMAGIXBOX TM. Quick Start Guide
TM TM by TouchMagix MAGIXBOX TM Quick Start Guide What s in the box: Ankle Ceiling Plate Extendable Rod Connector Piece Middle Piece Universal Spider Super clamp with ball socket Safety Cable Projector
More informationBPL SERIES INSTALLATION INSTRUCTIONS THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
BPL SERIES INSTALLATION INSTRUCTIONS Important Warning THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. This product must be installed in accordance with National Electrical
More informationMCH WIRE HARNESS WITH QUICK DISCONNECT REPLACEMENT Initial Release 1/31/2013
1. Table of Contents 1. Table of Contents Page 1 2. Remove Failed MCH-103.2 Page 1 3. Install MCH-103.2 to MCH-102NW Page 2 4. Install NC3FX-HD to MCH-103.2 Page 3 5. Install MCH-103.2 Battery Terminal
More informationWritten By: Patrick. Disassembly to clean dust from the fan and heat sink. HP Pavilion G6 disassembly for cleaning
HP Pavilion G6 disassembly for cleaning Disassembly to clean dust from the fan and heat sink. Written By: Patrick ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION Disassembly to clean dust from
More informationReflowing Xbox 360 Motherboard
Reflowing Xbox 360 Motherboard Reflow the solder on your Xbox 360's motherboard. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 31 INTRODUCTION Use this guide to reflow the solder
More informationDell Inspiron E1705 Motherboard Replacement
This guide will show you, step by step, how to install a new motherboard. Written By: Malik Shahbal ifixit CC BY-NC-SA www.ifixit.com Page 1 of 13 TOOLS: Phillips #1 Screwdriver (1) ifixit Opening Tools
More informationUpgrading LVDS Cables Instruction Sheet
Upgrading LVDS Cables Instruction Sheet INTRODUCTION Use the following instructions to replace the LVDS cables in CP2000-M/MR projectors. The new cables are slightly longer in length and allow for better
More informationWritten By: Sydney Dye
Disassembling Panasonic LUMIX DMC-LX100 This guide will show you how to take apart your entire Panasonic LUMIX DMC-LX100. Written By: Sydney Dye ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION
More informationSkullcandy Air Raid USB Board Replacement
Skullcandy Air Raid USB Board Replacement The USB port should be replaced if it is visibly broken or the device will no longer charge. Written By: Cyrene ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12
More informationC202SA: Disassembly Guide
ASUS Computer International C202SA: Disassembly Guide PN: 90NX00Y2-M00040 PN: 90NX00Y2-M00050 IMPORTANT NOTICE: This document is intended for ASUS Authorized Service Providers only. Performing any repairs
More informationInstruction Manual. Electrical Management System (EMS) EMS-HW30C & EMS-HW50C
Instruction Manual Electrical Management System (EMS) EMS-HW30C & EMS-HW50C EMS-HW50C EMS-HW30C! CAUTION These instructions are intended to provide assistance with the installation of this product, and
More informationValidator Update Instructions for Rowe BC1200 $1 - $20
Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit
More informationRetina MacBook 2016 Display Assembly
Retina MacBook 2016 Display Assembly Replacement Replace the display assembly on the Retina MacBook 2016. Written By: Adam O'Camb ifixit CC BY-NC-SA www.ifixit.com Page 1 of 20 INTRODUCTION Use this guide
More informationCanon EOS 70D Camera Motherboard
Canon EOS 70D Camera Motherboard Replacement This guide will show you how to replace the main motherboard on a EOS 70D. Written By: Tyler Baker ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION
More informationWARNING ELECTRICAL SHOCK HAZARD
Description Safety Instructions The top-entry sub D9 connector kit is designed for enclosure sizes D1h D8h, E1 E2, and E1h E4h with VLT PROFIBUS DP MCA 101 option. It fits the following drives: VLT HVAC
More informationMi50 Inverted Microscope User s Manual. Fein.
Mi50 Inverted Microscope User s Manual Fein info@feinoptic.com Mi50 Microscope Components Siedentopf Trinocular Head Stage Plate Mechanical Stage Locking Screw Hex Wrench Storage Beam Splitter Dust Protector
More informationOnePlus 5 Screen and Digitizer Assembly Replacement
OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:
More informationASUS D550MA-DS01 Screen Replacement
ASUS D550MA-DS01 Screen Replacement This guide will show you how to replace your laptop screen. Written By: Calvin Wieczorek ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Many people will
More informationSeries 3700 Screw Terminal Assemblies Installation Instructions
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY www.keithley.com Series 3700 Screw Terminal Assemblies Installation Instructions Introduction This document contains handling
More informationHow to assemble and disassemble Anafi
How to assemble and disassemble Anafi Prerequisites The best way to repair ANAFI is to use Parrot official drones repair kit. You will need the cruciform as well as the Torx 5 (T5) in order to carry out
More informationCanon EOS Rebel T2i Top Cover Replacement
Canon EOS Rebel T2i Top Cover Replacement Replacing the top piece of a Canon T2i (550D). In my case, I had a broken hot-shoe, but as most controls on this camera are built into the same part, this repair
More informationXbox One Wireless Controller Bottom Motherboard Replacement
Xbox One Wireless Controller Bottom Motherboard Replacement Prerequisite Only: Remove the bottom motherboard for access to the buttons and triggers. Written By: Liam Gow ifixit CC BY-NC-SA www.ifixit.com
More informationElectrical Management System (EMS) EMS-HW30C & EMS-HW50C
Electrical Management System (EMS) EMS-HW30C & EMS-HW50C Installation & Operating Guide for: Model EMS-HW30C Rated at 120V/30A and Model EMS-HW50C Rated at 240V/50A Surgio Says Lifetime Warranty on all
More informationRetina MacBook 2015 Lower Case Assembly Removal
Retina MacBook 2015 Lower Case Assembly Removal Separate the lower case assembly. Written By: Geoff Wacker ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION Prerequisite-only guide for separating
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationArecont Vision MegaDome Installation Manual
0 P age MegaDome Installation Manual. recont Vision MegaDome B. Mounting template C. Magnetic core D. Pack of four (4) wood screws and four (4) dry wall anchors E. One double sided hex key F. One single
More informationMacBook Core 2 Duo Display Replacement
MacBook Core 2 Duo Display Replacement Written By: irobot ifixit CC BY-NC-SA www.ifixit.com Page 1 of 23 INTRODUCTION Change out the entire display assembly, including the inverter, Airport antennas, hinges
More informationMounting DIGITAL DISPLAY
Mounting The Class digital display mounts in a. by. cutout. Overall area necessary for installation is. by.. Two 0.0 diameter holes are provided for mounting screws..0".0..0.900 Ø 0.0" () HOLES."." DIGITAL
More informationIPhone 7 Plus Chargeport REPAIR GUIDE. Version Edition
IPhone 7 Plus Chargeport REPAIR GUIDE Version 1 2016 Edition IPhone 7 plus Chargeport Repair Guide RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL,
More informationMotorola Moto G4 Plus Motherboard Replacement
Motorola Moto G4 Plus Motherboard Replacement Remove and replace your motherboard as a prerequisite to other guides. Written By: Andre Rives ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION
More informationNational Optical & Scientific Instruments Inc Tri-County Parkway Schertz, Texas Phone (210) Fax (210) INSTRUCTIONS FOR
National Optical & Scientific Instruments Inc. 6508 Tri-County Parkway Schertz, Texas 78154 Phone (210) 590-9010 Fax (210) 590-1104 INSTRUCTIONS FOR 450 SERIES STEREOSCOPIC MICROSCOPES Copyright 4/6/2010
More informationUser Guide. Intel NUC 8 Business, a Mini PC with Windows 10 NUC8i7HNKQC. Intel NUC 8 Enthusiast, a Mini PC with Windows 10 NUC8i7HVKVA
Intel NUC 8 Business, a Mini PC with Windows 10 NUC8i7HNKQC Intel NUC 8 Enthusiast, a Mini PC with Windows 10 NUC8i7HVKVA User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume
More informationRetina MacBook 2015 Display Assembly
Retina MacBook 2015 Display Assembly Replacement Replace the display assembly on the Retina MacBook 2015. Written By: Geoff Wacker ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION Use this guide
More informationimac Intel 21.5" EMC 2428 SSD Dual Drive
imac Intel 21.5" EMC 2428 SSD Dual Drive Installation Install an SSD in your imac Intel 21.5" EMC 2428. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 33 INTRODUCTION Use this guide to install
More informationThinkCentre. Hardware Removal and Replacement Guide Types 8143, 8144, 8146 Types 8422, 8423, 8427
ThinkCentre Hardware Remoal and Replacement Guide Types 8143, 8144, 8146 Types 8422, 8423, 8427 ThinkCentre Hardware Remoal and Replacement Guide Types 8143, 8144, 8146 Types 8422, 8423, 8427 First Edition
More informationNikon D5000 Viewfinder Replacement
Nikon D5000 Viewfinder Replacement Disassembly down to the viewfinder hood and to the screen itself. Written By: Jacob Rardin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 9 INTRODUCTION If there is dust
More informationSPARE PARTS & HOW TO HANDLE. μ-icc 2.45 compact. - Instructions - S/N: A01-PG10-SPE Version No.: 0 V
SPARE PARTS & HOW TO HANDLE μ-icc 2.45 compact - Instructions - S/N: A01-PG10-SPE Version No.: 0 V1 2010-08-27 1 Introduction... 2 2 Safety instructions... 2 3 Open the housing... 3 4 Constituent parts
More informationMacBook Pro 17" Unibody AirPort Board Replacement
MacBook Pro 17" Unibody AirPort Board Replacement Replace the AirPort Board in your MacBook Pro 17" Unibody. Written By: Brett Hartt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION Having issues
More informationM40 Microscope User s Manual
M40 Microscope User s Manual for M40 and M40RT Microscope Components: Trinocular Port Eyepieces Beam Splitter Field Diaphragm Adjustment Aperture Diaphragm Adjustment Filter Slots Analyzer Polarizer Hex
More informationPortable Gas Monitor (PGM-IR) Infrared Sensor Replacement Instruction
Portable Gas Monitor (PGM-IR) Infrared Sensor Replacement Instruction 3015-5508 Rev. 3 January 2018 1. Scope These instructions describe how to replace the IR sensor in the Portable Gas Monitor (example
More informationA Backlighted LCD for your K1
A Backlighted LCD for your K1 (K1BKLTKIT) Tom Hammond - NØSS, July 27, 2006 Rev C Thanks to Wayne Burdick, N6KR for suggesting this implementation of backlighting the K1 display. APPLICABILITY This modification
More informationOlympus Stylus 1030 SW Camera Lens Replacement
Olympus Stylus 1030 SW Camera Lens Replacement Written By: Shanmei Zheng ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 TOOLS: Phillips #00 Screwdriver (1) ifixit Opening Tools (1) Spudger (1) T6 Torx
More informationIntel NUC Kit DC53427HYE User Guide. Intel NUC Kit DC53427HYE
Intel NUC Kit DC53427HYE User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers and with the safety
More information