for NuMicro NUC029FAE Series

Transcription

1 for NuMicro NUC09FAE Series The information described in this document is the exclusive intellectual property of Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton. Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system design. Nuvoton assumes no responsibility for errors or omissions. All data and specifications are subject to change without notice. For additional information or questions, please contact: Nuvoton Technology Corporation. Dec. 4, 04 Rev..0

2 Table of Contents Overview... 3 Introduction to NuTiny-SDK-NUC09FAE NuTiny-SDK-NUC09FAE Jumper Description Pin Assignment for Extended Connectors NuTiny-SDK-NUC09FAE PCB Placement Starting to Use NuTiny-SDK-NUC09FAE on the Keil μvision IDE Downloading and Installing Keil μvision IDE Software Downloading and Installing Nuvoton Nu-Link Driver Hardware Setup Example Program Starting to Use NuTiny-SDK-NUC09FAE on the IAR Embedded Workbench 9 4. Downloading and Installing IAR Embedded Workbench Software Downloading and Installing Nuvoton Nu-Link Driver Hardware Setup Example Program NuTiny-SDK-NUC09FAE Schematics NuTiny-EVB-NUC09FAE Schematic Nu-Link-Me Schematic... 6 Downloading NuMicro Related Files from Nuvoton Website Downloading NuMicro Keil μvision IDE Driver Downloading NuMicro IAR EWARM Driver Downloading NuMicro NUC09FAE Series BSP Software Library Revision History... Dec. 4, 04 of Rev..0

3 Overview The NuTiny-SDK-NUC09FAE is a specific development tool for NuMicro NUC09FAE series-nuc09fae by which users can develop and verify the application program easily. The NuTiny-SDK-NUC09FAE includes two portions: NuTiny-EVB- NUC09FAE (an evaluation board) and Nu-Link-Me (Debug Adaptor). With the NuTiny- SDK-NUC09FAE, users do not need additional ICE or debug equipment. Introduction to NuTiny-SDK-NUC09FAE The following figure shows the NuTiny-SDK-NUC09FAE for NUC09xAE series, in which the left portion is called NuTiny-EVB-NUC09FAE and the right portion is Debug Adaptor called Nu-Link-Me. The NuTiny-EVB-NUC09FAE is similar to other development board. Users can use it to develop and verify applications to emulate the real behavior. In fact, the real chip NUC09FAE is mounted on the board. The NuTiny-EVB-NUC09FAE can be a real system controller to design user target system. The Nu-Link-Me is a Debug Adaptor which connects the USB port of your PC to your target system (via Serial Wired Debug Port) and allows you to program and debug embedded programs on the target hardware. To use the Nu-Link-Me Debug adaptor with Keil or IAR, please refer to Nuvoton NuMicro IAR ICE Driver User Manual or Nuvoton NuMicro Keil ICE Driver User Manual for details. (JP) TSSOP-0 pin Extended Connector (J4) (JP5) :3.3V or 5V (JP8) I/O LED Power LED Reset Key (SW) GND (JP3) TSSOP-0 pin Extended Connector (J3) GND (JP6) Target Chip ICE Controller Figure - NuTiny-SDK-NUC09FAE (Green PCB Board) ICE Controller USB Connector (ICEJ) Dec. 4, 04 3 of Rev..0

4 . NuTiny-SDK-NUC09FAE Jumper Description.. Power Settings JP and JP5: Voltage connecter in NuTiny-EVB-NUC09FAE ICEJ: USB port in Nu-Link-Me Model Model JP8 Select 33 (default) ICEJ USB port Model X X X: Unused... Debug Connectors JP and JP5 MCU Voltage Connect to PC DC 3.3V output DC 3.3V DC.5 V ~ 5.5 V Input Voltage by JP and JP5 input JP4: Connector in target board (NuTiny-EVB-NUC09FAE) for connecting with Nuvoton ICE adaptor (Nu-Link-Me) ICEJP8: Connector in ICE adaptor (Nu-Link-Me) for connecting with a target board (e.g. NuTiny-EVB-NUC09FAE)..3 USB Connectors ICEJ: Mini USB Connector in Nu-Link-Me connected to a PC USB port..4 Extended Connectors J3 and J4: Show all chip pins in NuTiny-EVB-NUC09FAE..5 Buttons SW: Reset button in NuTiny-EVB-NUC09FAE..6 Power Connectors JP and JP5: connector in NuTiny-EVB-NUC09FAE JP3 and JP6: GND connector in NuTiny-EVB-NUC09FAE Dec. 4, 04 4 of Rev..0

5 . Pin Assignment for Extended Connectors The NuTiny-EVB-NUC09FAE provides the NUC09FAE target chip on board and the extended connectors (J3 and J4) for TSSOP0-pin. The following table is the pin assignment for NUC09FAE. Pin No Pin Name Pin No Pin Name 0 P.,RXD,AIN,ACMP0_P VSS 0 P.3,TXD,AIN3,ACMP0_P P.4,PWM 03 P.4,AIN4,ACMP0_N 3 P.5,PWM3 04 P.5,AIN5,ACMP0_P 4 P4.6,ICE_CLK 05 nrst 5 P4.7,ICE_DAT 06 P3.,nINT0,STADC,T0EX, ACMP_P 6 P0.7,SPICLK0 07 P3.4,T0,SDA0,ACMP_P 7 P0.6,MISO_0 08 P3.5,T,SCL0,ACMP_P 8 P0.5,MOSI_0 09 P5.,XTAL 9 P0.4,SPISS0,PWM5 0 P5.0,XTAL 0 VDD Table - Pin Assignment for NUC09FAE Dec. 4, 04 5 of Rev..0

6 .3 NuTiny-SDK-NUC09FAE PCB Placement The following figure shows the NuTiny-SDK-NUC09FAE PCB placement. Figure - NuTiny-SDK-NUC09FAE PCB Placement Dec. 4, 04 6 of Rev..0

7 3 Starting to Use NuTiny-SDK-NUC09FAE on the Keil μvision IDE 3. Downloading and Installing Keil μvision IDE Software Please connect to the Keil company website ( to download the Keil μvision IDE and install the RVMDK. 3. Downloading and Installing Nuvoton Nu-Link Driver Please connect to Nuvoton NuMicro website ( to download the NuMicro Keil μvision IDE driver file. Please refer to section 6. for the detailed download flow. After the Nu-Link driver is downloaded, please unzip the file and execute the Nu-Link_Keil_Driver.exe to install the driver. 3.3 Hardware Setup The hardware setup is shown in the following figure. Figure 3- NuTiny-SDK-NUC09FAE Hardware Setup Dec. 4, 04 7 of Rev..0

8 3.4 Example Program This example demonstrates how to download and debug an application on a NuTiny- SDK-NUC09FAE board. The example file can be found in the directory list shown in the following figure. Directory Figure 3- Example Directory To use this example: The I/O LED on the NuTiny-EVB-NUC09FAE board will be toggled on. Start μvision Project Open Open the led.uvproj project file Project Build Compile and link the LED application Flash Download Program the application code into on-chip Flash ROM Start Debug mode When using the debugger commands, you may: Review variables in the watch window Single step through code Reset the device Run the application Dec. 4, 04 8 of Rev..0

9 4 Starting to Use NuTiny-SDK-NUC09FAE on the IAR Embedded Workbench 4. Downloading and Installing IAR Embedded Workbench Software Please connect to IAR company website ( to download the IAR Embedded Workbench and install the EWARM. 4. Downloading and Installing Nuvoton Nu-Link Driver Please connect to Nuvoton Company NuMicro website ( to download NuMicro IAR EWARM Driver file. Please refer to section 6. for the detail download flow. After the Nu-Link driver is downloaded, please unzip the file and execute the Nu-Link_IAR_Driver.exe to install the driver. 4.3 Hardware Setup The hardware setup is shown in the following figure. Figure 4- NuTiny-SDK-NUC09FAE Hardware Setup Dec. 4, 04 9 of Rev..0

10 4.4 Example Program This example demonstrates how to download and debug an application on a NuTiny- SDK-NUC09FAE board. The example file can be found in the directory list shown in the following figure. Directory Figure 4- Example Directory To use this example: The I/O LED on the NuTiny-EVB-NUC09FAE board will be toggled on. Start IAR Embedded Workbench File-Open-Workspace Open the led.eww workspace file Project Download and Debug Program the application code into on-chip Flash ROM Project - Make Compile and link the LED application Single step through code Reset the device Run the application Dec. 4, 04 0 of Rev..0

11 5 NuTiny-SDK-NUC09FAE Schematics 5. NuTiny-EVB-NUC09FAE Schematic TICE TICEDAT TICECLK TICERST TICE TICEDAT TICECLK TICERST SW SW PUSH BOTTOM R 0K TICERST C 0uF/0V TANT-A J3 PIN PIN PIN3 3 PIN4 4 PIN5 5 PIN6 6 PIN7 7 PIN8 8 PIN9 9 PIN0 0 U PIN PIN ACMP0_P,RXD,AIN,P. VDD 0 9 PIN3 3 ACMP0_P,TXD,AIN3,P.3 P0.4,SPISS0,PWM5 8 PIN4 4 ACMP0_N,AIN4,P.4 P0.5,MOSI_0 7 TICERSTPIN5 5 ACMP0_N,AIN5,P.5 P0.6,MISO_0 6 PIN6 6 nrst P0.7,SPICLK0 5 PIN7 7 ACMP_P,T0EX,STADC,nINT0,P3. P4.7,ICE_DAT 4 PIN8 8 ACMP_P,SDA0,T0,P3.4 P4.6,ICE_CLK 3 XTAL PIN9 9 ACMP_P,SCL0,T,P3.5 P.5,PWM3 XTAL PIN0 0 XTAL,P5. P.4,PWM XTA, P5.0 VSS PIN0 PIN9 PIN8 PIN7 PIN6 PIN5 PIN4 PIN3 PIN PIN TICEDAT TICECLK Reset Circuit From ICE Bridge's USB Power JP4 TICE TICEDAT 3 4 TICECLK 5 6 TICERST HEADER 5PX(NC) SIPSOC-0 (NC) J4 PIN PIN PIN3 3 PIN PIN4 4 PIN5 5 PIN6 6 PIN7 7 PIN8 8 PIN9 9 PIN0 0 SIPSOC-0 (NC) NUC09FAE_TOSSOP0 PIN6 TICERST TP TP TP3 Test_Point (NC) Test_Point (NC) Test_Point (NC) JP5 HEADER PX (NC) JP6 HEADER PX (NC) JP HEADER 5PX (NC) JP ICE Interface R 330 PR 330 HEADER 5PX (NC) IO RED LED0805 POWER GREEN LED0805 C3 0p C0603 C5 R 33 X MHz R4 XTAL\LP\SMD M XTAL XTAL PIN 0p C0603 Crystal Title NuTiny-EVB-NUC09FAE Size Document Number Rev Custom NUC09FAE.SCH V.0 Friday, June 3, 04 Date: Sheet of Dec. 4, 04 of Rev..0

12 VBUS VBUS VDD33 D- D+ PB0/RX0 PB/TX0 PB/RTS0 PB3/CTS0 PC3/SDO00 PC/SDI00 PC/SPCLK0 PC0/SS00 PE5 PB/TM3 PB0/SS0/TM PB9/SS/TM 64 STADC/TM0/PB8 63 PVSS 6 VDD 6 VSS 60 /RESET 59 XT_In 58 XT_Out 57 INT/PB5 56 CPP/PC4 55 CPN/PC5 54 CPP0/PC6 CPN0/PC7 53 AVDD 5 5 ADC7/PA7 50 ADC6/PA6 49 ADC/PA5 ICE_RST M_I M_O 3 4 IN GND OUT OUT ADAVSS 5. Nu-Link-Me Schematic iced4 5 USBVBUS SS4A RB060L U3 AMS7-3.3V JP8 3-W JUMPER AVDD icel4 L0603 icel5 iced3 SS4A RB060L icejp9 ICE_DAT ICE_CLK 3 ICE_RST 4 5 HEADER 5PX (NC) RTIDA 00K RICK 00K TICE TICEDAT TICECLK TICERST TICE TICEDAT TICECLK TICERST iced SS4A RB060L icejp HEADER 5PX (NC) CT3 0uF/0V TANT-A POWER ADAVSS L0603 DEBUG ICE CONNECT IF USBVBUS icer M_O 33 icer3 M/DNE M_I Crystal icec6 0p icex3 C0603 MHz XTAL\LP\SMD icec7 0p C0603 iceu AVDD USB_D- USB_D+ icer4 33 icer6 33 DM DP J 3 4 icej 3 DM 4 DP 5 NC GND mini USB 5pin USB_MINI_B USBVBUS DM DP SHIELD 6 SHIELD 7 SHIELD 8 SHIELD 9 icel6 L0603 ICELED (RED) ICP ICPLED (YELLOW) YELLOW LED0805 RED (RED) GREEN (GREEN) ICE IDLE RED LED0805 RED LED0805 BUSY GREEN LED0805 icerp P4R-330 8P4RA ICELED ICPLED RED GREEN icect icecb3 0uF/0V 0.uF TANT-A C VDD VSS INT0/PB4 CPO/PB3 CPO0/PB X3I X3O ICSCL/PA ICSDA/PA0 IC0SCL/PA9 IC0SDA/PA8 RX/PB4 TX/PB5 RTS/PB6 CTS/PB7 LDO NUCSRE3AN_LQFP64 48 PA4/ADC4 47 PA3/ADC3 46 PA/ADC 45 PA/ADC 44 PA0/ADC0 43 AVSS 4 ICE_CK 4 ICE_DAT 40 PA/PWM0 39 PA3/PWM 38 PA4/PWM 37 PA5/PWM3 36 PC8/SS0 35 PC9/SPCLK 34 PC0/SDI0 33 PC/SDO0 HEADER 4PX (NC) ICE_CLK ICE_DAT TICERST TICECLK RTDA 0 RTDA3 33 RRSET RTCK 00K 00K TICEDAT RTDA 00K icer7 0K ICE_RST USBVBUS icec8 uf C0603 USB_D+ USB_DiceCB4 0.u C0603 MCU and USB icec9 0uF/0V TANT-A Reset Circuit Title Nu-Link-Me V.0 Size Document Number Rev Custom ICE_LQFP64.SCH V.0 Wednesday, May, 04 Date: Sheet of Dec. 4, 04 of Rev..0

13 6 Downloading NuMicro Related Files from Nuvoton Website 6. Downloading NuMicro Keil μvision IDE Driver Step Visit the Nuvoton NuMicro website: -. Move to Support Step -. Click here to enter Tool & Software Dec. 4, 04 3 of Rev..0

14 Step3 Click here to enter Software download page Dec. 4, 04 4 of Rev..0

15 Click here to download the file. Step4 Step5 Download the NuMicro Keil μvision IDE driver. Dec. 4, 04 5 of Rev..0

16 6. Downloading NuMicro IAR EWARM Driver Step Visit the Nuvoton NuMicro website: -. Move to Support Step -. Click here to enter Tool & Software Dec. 4, 04 6 of Rev..0

17 Step3 Click here to enter Software download page Dec. 4, 04 7 of Rev..0

18 Step4 Click here to download the file. Step5 Download the NuMicro IAR EWARM driver. Dec. 4, 04 8 of Rev..0

19 6.3 Downloading NuMicro NUC09FAE Series BSP Software Library Step Visit the Nuvoton NuMicro website: -. Move to Support Step -. Click here to enter Tool & Software Dec. 4, 04 9 of Rev..0

20 Step3 Click here to enter Software download page Step4 Download the NuMicro NUC09FAE Series CMSIS BSP. Dec. 4, 04 0 of Rev..0

21 7 Revision History Revision Date Description.00 Jun. 9, 04 First version..0 Dec. 4, 04 Fix the typo on 6.3 Downloading NuMicro NUC09FAE Series BSP Software Library Step4. Important Notice Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any malfunction or failure of which may cause loss of human life, bodily injury or severe property damage. Such applications are deemed, Insecure Usage. Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic energy control instruments, airplane or spaceship instruments, the control or operation of dynamic, brake or safety systems designed for vehicular use, traffic signal instruments, all types of safety devices, and other applications intended to support or sustain life. All Insecure Usage shall be made at customer s risk, and in the event that third parties lay claims to Nuvoton as a result of customer s Insecure Usage, customer shall indemnify the damages and liabilities thus incurred by Nuvoton. Dec. 4, 04 of Rev..0