for NuMicro NUC220 Series

Transcription

1 NuTiny-SDK-NUC220 User Manual for NuMicro NUC220 Series The information described in this document is the exclusive intellectual property of Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton. Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system design. Nuvoton assumes no responsibility for errors or omissions. All data and specifications are subject to change without notice. For additional information or questions, please contact: Nuvoton Technology Corporation. Jan. 23, 2013 Rev. 1.00

2 Table of Contents 1 Overview Introduction to NuTiny-SDK-NUC NuTiny-SDK-NUC220 Jumper Description Pin Assignment for Extended Connectors NuTiny-SDK-NUC220 PCB Placement Starting to Use NuTiny -SDK-NUC220 on the Keil μvision IDE Downloading and Installing Keil μvision IDE Software Downloading and Installing Nuvoton Nu-Link Driver Hardware Setup Smpl_NuTiny-NUC220 Program Starting to Use NuTiny-SDK-NUC220 on the IAR Embedded Workbench Downloading and Installing IAR Embedded Workbench Software Downloading and Installing Nuvoton Nu-Link Driver Hardware Setup Smpl_NuTiny-NUC220 Program NuTiny-EVB-NUC220 Schematics Downloading NuMicro Related Files from Nuvoton Website Downloading NuMicro Keil μvision IDE Driver Downloading NuMicro IAR EWARM Driver Downloading NuMicro NUC220 series BSP Software Library Revision History Jan. 23, of 18 Rev. 1.00

3 1 Overview The NuTiny-SDK-NUC220 is a specific development tool for the NuMicro NUC220 series users to develop and verify the application program easily. The NuTiny-SDK- NUC220 includes two portions: NuTiny-EVB-NUC220 (an evaluation board) and Nu- Link-Me (its Debug Adaptor), such that users do not need additional ICE or debug equipment. Jan. 23, of 18 Rev. 1.00

4 2 Introduction to NuTiny-SDK-NUC220 The NuTiny-SDK-NUC220 uses the NUC220VE3AN as the target microcontroller. Figure 2-1 shows the NuTiny-SDK-NUC220 for NUC220 series, in which the left portion is called NuTiny-EVB-NUC220 and the right portion is called Nu-Link-Me. The NuTiny-EVB-NUC220 is similar to other development boards, by which users can develop and verify applications to emulate the real behavior. The on board chip covers NUC220 series features. The NuTiny-EVB-NUC220 can be a real system controller to design the users target systems. The Nu-Link-Me is a Debug Adaptor, which connects your PC's USB port to a target system (via Serial Wired Debug Port) and allows you to program and debug embedded programs on the target hardware. To use the Nu-Link-Me Debug adaptor with IAR or Keil, please refer to Nuvoton NuMicro IAR ICE Driver User Manual or Nuvoton NuMicro Keil ICE Driver User Manual for details. The two documents will be stored in the local hard disk when each is installed. Figure 2-1 NuTiny-SDK-NUC220 PCB Board Jan. 23, of 18 Rev. 1.00

5 2.1 NuTiny-SDK-NUC220 Jumper Description Power Settings JP1: VCC5 Voltage connecter in NuTiny-EVB-NUC220 J2: USB port in Nu-Link-Me JPR1: Select 5V or 3V for system power J1: USB port in NuTiny-EVB-NUC220 POWER model J1 USB port J2 USB port JP2 VCC5 MCU Voltage Model 1 Connect to PC X DC 5V output DC 5V Model 2 X Connect to PC DC 5V output DC 5V Model 3 X X DC V input X: Unused Debug Connectors Voltage by VCC input JP4: Connector in target board (NuTiny-EVB-NUC220) for connecting with Nuvoton ICE adaptor (Nu-Link-Me) JP9 Connector in ICE adaptor (Nu-Link-Me) for connecting with a target board (e.g. NuTiny-EVB-NUC220) USB Connectors J1: Mini USB Connector in NuTiny-EVB-NUC220 for application use J2: Mini USB Connector in Nu-Link-Me connected to a PC USB port Extended Connectors JP3, JP5, JP7 and JP8: Show all chip pins in NuTiny-EVB-NUC Buttons SW1: Reset button in NuTiny-EVB-NUC Power Connectors JP2: VDD33 connector in NuTiny-EVB-NUC220 JP3: GND connector in NuTiny-EVB-NUC Power Jumpers JP1: VCC connector in NuTiny-EVB-NUC220 JP2: GND connector in NuTiny-EVB-NUC220 Jan. 23, of 18 Rev. 1.00

6 2.2 Pin Assignment for Extended Connectors The NuTiny-EVB-NUC220 provides the NUC220KE3BN target chip on board and the extended connectors (JP3, JP5, JP7 and JP8) for LQFP100-pin Pin Pin Name Pin Pin Name Pin Pin Name Pin Pin Name No 01 PE15 No 26 PE8 No 51 PE4 No 76 PA5 02 PE14 27 PE7 52 PE3 77 PA6 03 PE13 28 VBUS 53 PE2 78 PA7 04 PB14 29 VDD33 54 PE1 79 Vref 05 PB13 30 D- 55 PE0 80 AVDD 06 VBAT 31 D+ 56 PC13 81 PD0 07 X32O 32 PB0 57 PC12 82 PD1 08 X32I 33 PB1 58 PC11 83 PD2 09 PA11 34 PB2 59 PC10 84 PD3 10 PA10 35 PB3 60 PC9 85 PD4 11 PA9 36 PD6 61 PC8 86 PD5 12 PA8 37 PD7 62 PA15 87 PC7 13 PD8 38 PD14 63 PA14 88 PC6 14 PD9 39 PD15 64 PA13 89 PC15 15 PD10 40 PC5 65 PA12 90 PC14 16 PD11 41 PC4 66 ICE_DAT 91 PB15 17 PD12 42 PC3 67 ICE_CK 92 XT1_Out 18 PD13 43 PC2 68 VDD 93 XT1_In 19 PB4 44 PC1 69 VSS 94 /RESET 20 PB5 45 PC0 70 AVSS 95 VSS 21 PB6 46 PE6 71 PA0 96 VDD 22 PB7 47 PE5 72 PA1 97 PS2DAT 23 LDO 48 PB11 73 PA2 98 PS2CLK 24 VDD 49 PB10 74 PA3 99 PVSS 25 VSS 50 PB9 75 PA Table 2-1 NUC220VE3AN LQFP 100-pin Assignment for Extended Connectors PB8 Jan. 23, of 18 Rev. 1.00

7 2.3 NuTiny-SDK-NUC220 PCB Placement The following figure shows the NuTiny-SDK-NUC220 PCB placement. Figure 2-2 NuTiny-SDK-NUC220 PCB Placement Jan. 23, of 18 Rev. 1.00

8 3 Starting to Use NuTiny -SDK-NUC220 on the Keil μvision IDE 3.1 Downloading and Installing Keil μvision IDE Software Please connect to the Keil company website ( to download the Keil μvision IDE and install the RVMDK. 3.2 Downloading and Installing Nuvoton Nu-Link Driver Please connect to Nuvoton NuMicro website ( to download the NuMicro Keil μvision IDE driver file. Please refer to section 6.1 for the detailed download flow. After the Nu-Link driver is downloaded, please unzip the file and execute the Nu-Link_Keil_Driver.exe to install the driver. 3.3 Hardware Setup The hardware setup is shown in the following figure. Figure 3-1 NuTiny-SDK-NUC220 Hardware Setup Jan. 23, of 18 Rev. 1.00

9 3.4 Smpl_NuTiny-NUC220 Program The example, as shown in the directory of Figure 3-2, demonstrates the download and debugging of an application on a NuTiny-SDK-NUC220 board. The example file can be downloaded from Nuvoton NuMicro website as described in 6.3 Downloading NuMicro NUC220 series BSP Software Library. Directory Project File Figure 3-2 Smpl_NuTiny_200 Example Directory To use this example: The PA.10 LED will toggle on the NuTiny-EVB-NUC220 board. Start μvision Project-Open Open the Smpl_NuTiny_200.uvproj project file Project - Build Compile and link the Smpl_NuTiny_200 application Flash Download Program the application code into on-chip Flash ROM Start Debug mode When using the debugger commands, you may: Review variables in the watch window Single step through code Reset the device Run the application Jan. 23, of 18 Rev. 1.00

10 4 Starting to Use NuTiny-SDK-NUC220 on the IAR Embedded Workbench 4.1 Downloading and Installing IAR Embedded Workbench Software Please connect to IAR company website ( to download the IAR Embedded Workbench and install the EWARM. 4.2 Downloading and Installing Nuvoton Nu-Link Driver Please connect to Nuvoton Company NuMicro website ( to download the NuMicro IAR ICE Driver User Manual file. Please refer to section 6.2 for the detailed download flow. When the Nu- Link driver has been well downloaded, please unzip the file and execute the Nu- Link_IAR_Driver.exe to install the driver. 4.3 Hardware Setup The hardware setup is shown in the following figure. Figure 4-1 NuTiny- SDK-NUC220 Hardware Setup Jan. 23, of 18 Rev. 1.00

11 4.4 Smpl_NuTiny-NUC220 Program The example, as shown in the directory of Figure 4-2, demonstrates the download and debugging of an application on a NuTiny-SDK-NUC220 board. The example file can be downloaded from Nuvoton NuMicro website as described in 6.3 Downloading NuMicro NUC220 series BSP Software Library... Directory Project File Figure 4-2 Smpl_NuTiny-NUC220 Example Directory To use this example: The PA.10 LED will toggle on the NuTiny-EVB-NUC220 board. Start IAR Embedded Workbench File-Open-Workspace Open the NuTiny-EVB-NUC220.eww workspace file Project Download and Debug Program the application code into on-chip Flash ROM Single step through code Project - Make Compile and link the NuTiny-EVB-NUC220 application Reset the device Run the application Jan. 23, of 18 Rev. 1.00

12 Jan. 23, of 18 Rev NuTiny-EVB-NUC220 Schematics P16 P95 P64 P D1 NC RB060L DVBUS P74 P78 P95 D12MO P38 P56 ICEDAT P3 TICEDAT P18 P11 P33 P71 X2 12MHz XTAL3-1 P11 P84 P73 P23 GND 1 2 IO1 KPT-2012 KP-2012 P96 P91 P92 ICEDAT DAVDD P60 P66 DM1 P21 JP8 HEADER 13X TICECLK P23 DX32I P34 P53 JP6 HEADER P5 P71 P58 P24 VCC P29 P99 P86 P91 P66 R3 33 R0603 P65 P43 DP1 P14 GND P8 P38 P41 C1 10uF/10V TANT-A TICERST P20 P56 P74 P13 P33 JP5 HEADER 13X P80 P77 P88 ICECLK P34 P68 DP1 P7 P21 P26 P59 VCC CT1 10uF/6.3V TANT-R P17 P68 P12 P6 DVBUS P98 P87 RESET P67 C6 1u C0603 P52 P67 USBD- P97 ADAVSS P4 USBD+ P61 SW1 PUSH BOTTOM SW GND P24 P75 P18 J1 mini USB 5pin USB_MINI_B GND NC DP DM VCC SHIELD SHIELD SHIELD SHIELD Reset P81 GND P94 P69 P31 P28 R4 33 R0603 DM1 P79 P14 P31 P49 C4 20p C0603 P22 P70 P22 Crystal P82 P88 D12MI P60 JP3 HEADER 13X P73 P40 USBD+ P86 CB1 0.1u C0603 P37 P50 ICERST P9 P54 P42 C3 20p C0603 ICE INTERFACE P100 P85 P93 P63 P10 P37 P69 L1 L0603 DX32I P82 DAVDD P40 P27 TICERST R10 0 R0603 P4 P55 P44 PR1 500 R0603 P97 P100 P59 P3 P47 P42 ICERST P77 C2 20p C0603 P35 P55 ICERST P2 P52 P32 JP4 HEADER 5X P90 P96 P65 P5 P64 P75 L2 L0603 D12MI P87 P50 P30 C5 20p C0603 ICECLK VCC5 P13 P53 P36 P39 L4 L0805 P79 P76 P72 P15 P45 P51 RESET P78 JP1 HEADER P48 P70 TICECLK P8 P2 P46 P29 P92 P98 P62 P19 X K XTAL-3.4MM-2P P72 P26 D12MO P85 P43 P48 JP7 HEADER 13X ICECLK P6 P25 P27 P41 DVBUS JP2 HEADER P89 P81 P51 P16 P46 P39 DX32O P90 P44 P54 ICEDAT U1 NUC220_LQFP TM1/SPISS11/PB.9 TM2/SPISS01/PB.10 TM3/PMW4/PB.11 T1EX/PWM5/PE.5 PE.6 I2SLRCLK/SPISS00/PC.0 I2SBCLK/SPICLK0/PC.1 I2SDI/SPIMISO00/PC.2 I2SDO/SPIMOSI00/PC.3 SPIMISO01/PC.4 SPIMOSI01/PC.5 TX2/PD.15 RX2/PD.14 PD.7 PD.6 T3EX/SC2CD/CTS0/PB.3 T2EX/RTS0/PB.2 TX0/PB.1 RX0/PB.0 USB_D+ USB_D- VDD33 VBUS PE.7 PE.8 VSS VDD LDO_CAP CTS1/PB.7 RTS1/PB.6 TX1/PB.5 RX1/PB.4 SPIMOSI31/PD.13 SPIMISO31/PD.12 SPIMOSI30/PD.11 SPIMISO30/PD.10 SPICLK3/PD.9 SPISS30/PD.8 I2C0SDA/PA.8 I2C0SCL/PA.9 I2C1SDA/PA.10 I2C1SCL/PA.11 X32_I X32_O VBAT CPO1/PB.13 INT0/SPISS1/PB.14 PE.13 PE.14 PE.15 CLKO/TM0/PB.8/STADC PVSS PS2CLK/PF.3 PS2DAT/PF.2 VDD VSS /RESET XT_IN/PF.1 XT_OUT/PF.0 T0EX/INT1/PB.15 CPP1/PC.14 CPN1/PC.15 CPP0/PC.6/SC0CD CPN0/PC.7/SC1CD SPIMOSI21/PD.5 SPIMISO21/PD.4 SPIMOSI20/PD.3 SPIMISO20/PD.2 SPICLK2/PD.1 SPICS20/PD.0 AVDD VREF ADC7/PA.7/SC1DAT/SPISS21 ADC6/PA.6/SC1CLK ADC5/PA.5/SC1RST SC1PWR/ADC4/PA.4 SC0DAT/ADC3/PA.3 SCOCLK/ADC2/PA.2 SCORST/ADC1/PA.1 SC0PWR/ADC0/PA.0 AVSS VSS VDD ICE_CLK ICE_DAT SC2DAT/PWM0/PA.12 SC2CLK/PWM1/PA.13 SC2RST/PWM2/PA.14 SC2PWR/I2SMCLK/PWM3/PA.15 MCLK/SPISS10/PC.8 SPICLK1/PC.9 SPIMISO10/PC.10 SPIMOSI10/PC.11 SPIMISO11/PC.12 SPIMISO11/PC.13 PWM6/PE.0 PWM7/PE.1 PE.2 PE.3 PE.4 P25 DX32O P28 P47 P76 P89 P57 P1 R1 10K R0603 P63 P62 P94 P83 P83 P58 P36 L3 L0603 P10 P19 P12 P7 P49 USBD- ADAVSS VCC5 P1 P99 P61 P20 P35 P POWER1 KPT-2012 KP-2012 VCC5 P93 P84 P80 P57 GND TICEDAT P10 R2 500 R0603 P15 P9 P45 P30

13 6 Downloading NuMicro Related Files from Nuvoton Website 6.1 Downloading NuMicro Keil μvision IDE Driver Step1 Visit the Nuvoton NuMicro website: Step2 Click here to enter Tool & Software. Step3 Click here to enter Device Driver and Software Library. Jan. 23, of 18 Rev. 1.00

14 Step4 Click here to download the file. Step5 Download the NuMicro Keil μvision IDE driver. Jan. 23, of 18 Rev. 1.00

15 6.2 Downloading NuMicro IAR EWARM Driver Step1 Visit the Nuvoton NuMicro website: Step2 Click here to enter Tool & Software. Step3 Click here to enter Device Driver and Software Library. Jan. 23, of 18 Rev. 1.00

16 Step4 Click here to download the file. Step5 Download the NuMicro IAR EWARM driver. Jan. 23, of 18 Rev. 1.00

17 6.3 Downloading NuMicro NUC220 series BSP Software Library Step1 Visit the Nuvoton NuMicro website: Step2 Click here to enter Tool & Software. Step3 Click here to enter Device Driver and Software Library. Step 3 Download the NuMicro NUC220 series software library. Jan. 23, of 18 Rev. 1.00

18 7 Revision History Revision Date Description 1.00 Jan. 23, 2013 Initially issued. Important Notice Nuvoton products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Nuvoton products are not intended for applications wherein failure of Nuvoton products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Nuvoton customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Nuvoton for any damages resulting from such improper use or sales. Please note that all data and specifications are subject to change without notice. All the trademarks of products and companies mentioned in this datasheet belong to their respective owners. Jan. 23, of 18 Rev. 1.00