NuMicro Family NuTiny-SDK-NANO130 User Manual

Transcription

1 NUTINY-SDK-NANO0 USER MANUAL NANO0 ARM Cortex -M0 -bit Microcontroller NuMicro Family NuTiny-SDK-NANO0 User Manual The information described in this document is the exclusive intellectual property of Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton. Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system design. Nuvoton assumes no responsibility for errors or omissions. All data and specifications are subject to change without notice. For additional information or questions, please contact: Nuvoton Technology Corporation. Feb., 0 Page of Rev.0

2 NUTINY-SDK-NANO0 USER MANUAL NANO0 Table of Contents OVERVIEW... NUTINY-SDK-NANO0 INTRODUCTION.... NuTiny -SDK-NANO0 Jumper Description..... Power Setting..... Debug Connector..... USB Connector..... Extended Connector..... Button..... Power Connector.... Pin Assignment for Extended Connector.... NuTiny-SDK-NANO0 PCB Placement... How to Start NuTiny-SDK-NANO0 on the Keil μvision IDE Keil uvision IDE Software Download and Install Nuvoton Nu-Link Driver Download and Install Hardware Setup Example Program... How to Start NuTiny-SDK-NANO0 on the IAR Embedded Workbench.... IAR Embedded Workbench Software Download and Install.... Nuvoton Nu-Link Driver Download and Install.... Hardware Setup.... Example Program... NuTiny-SDK-NANO0 Schematic.... NuTiny-EVB-NANO0 Schematic.... GPIO for pin Schematic.... Nu-Link-Me Schematic.... x TN LCD Schematic... REVISION HISTORY... Feb., 0 Page of Rev.0

3 NUTINY-SDK-NANO0 USER MANUAL NANO0 OVERVIEW NuTiny-SDK-NANO0 is the specific development tool for NuMicro NANO0 series. Users can use NuTiny-SDK-NANO0 to develop and verify the application program easily. NuTiny-SDK-NANO0 includes two portions. One is NuTiny-EVB-NANO0 and the other is Nu- Link-Me. NuTiny-EVB-NANO0 is the evaluation board and Nu-Link-Me is its Debug Adaptor. Thus, users do not need other additional ICE or debug equipments. NuTiny-SDK-NANO0_TNLCD includes one x LCD panel for NuTiny-EVB-NANO0. Users can connect NuTiny-SDK-NANO0_TNLCD to NuTiny-EVB-NANO0 to develop and verify the application. Figure - NuTiny-SDK-NANO0 with NuTiny-SDK-NANO0_TNLCD Feb., 0 Page of Rev.0

4 NUTINY-SDK-NANO0 USER MANUAL NANO0 NUTINY-SDK-NANO0 INTRODUCTION NuTiny-SDK-NANO0 uses the NANO0KEBN as the target microcontroller. Figure - is NuTiny-SDK-NANO0 for NANO0 series, the left portion is called NuTiny-EVB-NANO0 and the right portion is Debug Adaptor called Nu-Link-Me. Figure - is NuTiny-SDK- NANO0_TNLCD for NuTiny-SDK-NANO0 LCD display applications. NuTiny-EVB-NANO0 is similar to other development boards. Users can use it to develop and verify applications to emulate the real behavior. The on board chip covers NANO0 series features. The NuTiny-EVB-NANO0 can be a real system controller to design users target systems. The Nu-Link-Me is a Debug Adaptor. The Nu-Link-Me Debug Adaptor connects your PC's USB port to your target system (via Serial Wired Debug Port) and allows you to program and debug embedded programs on the target hardware. To use Nu-Link-Me Debug adaptor with IAR or Keil, please refer to Nuvoton NuMicro IAR ICE driver user manual or Nuvoton NuMicro Keil ICE driver user manual in detail. These two documents will be stored in the local hard disk when the user installs each driver. Extended Connector (JP, JP) Target Chip ICE Controller VDD (JP) Extended Connector (JP, JP) I/O LED GND (JP) Extended Connector (JP, JP) USB Connector (J) ICE Controller USB Connector (ICE J) Reset Button (SW) Button (SW) Extended Connector (JP, JP) Figure - NuTiny-SDK-NANO0 (PCB Board) Extended Connector (JP, JP) x TNLCD Panel Extended Connector (JP, JP) Figure - NuTiny-SDK-NANO0_TNLCD (PCB Board) Feb., 0 Page of Rev.0

5 NUTINY-SDK-NANO0 USER MANUAL NANO0. NuTiny -SDK-NANO0 Jumper Description.. Power Setting Model JP: V DD Voltage connecter in NuTiny-EVB-NANO0 ICE J: USB port in Nu-Link-Me J: USB port in NuTiny-EVB-NANO0 JP V DD ICE J ICE USB Port J USB Port MCU Voltage Model DC.V Output Connect to PC X DC.V Model DC.V Output X Connect to PC DC.V Model DC.V ~.V Input X X Voltage by JP Input X: Unused... Debug Connector JP: Connector in target board (NuTiny-EVB-NANO0) for connecting with Nuvoton ICE adaptor (Nu-Link-Me) ICE JP: Connector in ICE adaptor (Nu-Link-Me) for connecting with a target board (NuTiny-EVB-NANO0).. USB Connector J: Micro USB Connector in NuTiny-EVB-NANO0 connected to a PC USB port ICE J: Micro USB Connector in Nu-Link-Me connected to a PC USB port.. Extended Connector JP, JP, JP, and JP: Show all chip pins in NuTiny-EVB-NANO0 JP, JP, JP, JP: Show all chip pins in NuTiny-EVB-NANO0, and connected to NuTiny-SDK-NANO0_TNLCD.. Button SW: Reset button in NuTiny-EVB-NANO0 SW: PC. button in NuTiny-EVB-NANO0.. Power Connector JP: V DD connector in NuTiny-EVB-NANO0 JP: GND connector in NuTiny-EVB-NANO0 Feb., 0 Page of Rev.0

6 NUTINY-SDK-NANO0 USER MANUAL NANO0. Pin Assignment for Extended Connector NuTiny-EVB-NANO0 provides NANO0KEBN on board and the extended connector for LQFP-pin. Table - is the pin assignment for NANO0KEBN. Pin No Pin Name Pin No Pin Name 0 PE. PE./SPI0_MOSI0 0 PB./INT0/SC_CD/SPI_SS PE./SPI0_MISO0 0 PB./EBI_AD PE./SPI0_CLK 0 PB./EBI_AD0/FCLKO PE./PWM_CH/SPI0_SS0 0 NC PE.0/PWM_CH/IS_MCLK 0 X_OUT 0 0 X_IN PC./SPI_MOSI/PWM_CH/SNOO PER/INT/IC0_SCL PC./SPI_MISO/PWM_CH0/INT0/I C0_SDA 0 NC PC./SPI_MOSI0/UART_TXD 0 0 PA./IC_SCL/EBI_nRD/SC0_RST/S PI_MOSI0 PA.0/IC_SDA/EBI_nWR/SC0_PWR/ SPI_MISO0 PC.0/SPI_MISO0/UART_RXD PC./SPI_CLK/IC_SCL PA./IC0_SCL/SC0_DAT/SPI_CLK PC./SPI_SS0/EBI_MCLK/IC_SDA PA./IC0_SDA/SC0_CLK/SPI_SS0 PD. PD. PD.0 PA./PWM0_CH/IS_MCLK/TC/SC0 _PWR/UART0_TXD PA./PWM0_CH/EBI_AD/TC/UAR T0_RXD PA./PWM0_CH/EBI_AD/TC/IC0 _SCL PA./PWM0_CH0/EBI_AD/TC0/IC0 _SDA PD. 0 PF.0/INT0/ICE_DAT PD. PF./FCLKO/INT/ICE_CLK PD. NC PB./UART_RXD/SC0_CD/SPI_SS0 VDD 0 PB./UART_TXD/SC0_RST/SPI_CLK NC PB./UART_RTSn/EBI_ALE/SPI_MIS O0 PB./UART_CTSn/EBI_nCS/SPI_MO SI0 VSS VSS NC AVSS Feb., 0 Page of Rev.0

7 NUTINY-SDK-NANO0 USER MANUAL NANO0 LDO_CAP AVSS NC PA.0/AD0/SC_CD NC 0 PA./AD/EBI_AD VDD PA./AD/EBI_AD/UART_RXD NC PA./AD/EBI_AD0/UART_TXD VSS 0 VSS VSS VSS PA./AD/EBI_AD/SC_PWR/IC0_S DA PA./AD/EBI_AD/SC_RST/IC0_SC L PA./AD/EBI_AD/TC/SC_CLK/PW M0_CH PA./AD/EBI_AD/TC/SC_DAT/PW M0_CH PE. VREF PE. NC PE.0 AVDD PE. 00 PE. 0 PE. 0 NC 0 PD.0/UART_RXD/SPI_SS0/SC_CLK /AD PD./UART_TXD/SPI_CLK/SC_DAT /AD PD./UART_RTSn/IS_LRCLK/SPI_ MISO0/SC_PWR/AD0 PD./UART_CTSn/IS_BCLK/SPI_M OSI0/SC_RST/AD 0 NC 0 NC NC 0 PD./IS_DI/SPI_MISO/SC_CD NC 0 PD./IS_DO/SPI_MOSI NC 0 PB.0/UART0_RXD/SPI_MOSI0 0 PC./DA_OUT/EBI_AD/TC/PWM0_ CH PC./DA0_OUT/EBI_AD/TC0/SC_CD/ PWM0_CH0 PB./UART0_TXD/SPI_MISO0 0 PC./EBI_AD/TC0/PWM_CH PB./UART0_RTSn/EBI_nWRL/SPI_C LK PB./UART0_CTSn/EBI_nWRH/SPI_S S0 0 PC./EBI_AD/PWM_CH PB./INT/SNOOPER/SC_CD PD. NC Feb., 0 Page of Rev.0

8 NUTINY-SDK-NANO0 USER MANUAL NANO0 PD. XT_IN 0 PD. XT_OUT PD. NC PC./SPI0_MOSI nreset PC./SPI0_MISO VSS PC./SPI0_MOSI0/IS_DO/SC_RST VSS PC./SPI0_MISO0/IS_DI/SC_PWR NC PC./SPI0_CLK/IS_BCLK/SC_DAT 0 VDD PC.0/SPI0_SS0/IS_LRCLK/SC_CLK NC PE. PF./IC0_SDA NC PF./IC0_SCL 0 NC VSS PE./PWM_CH PVSS PB./PWM_CH0/TM/SC_DAT/SPI0 _MISO0 PB.0/SPI0_SS/TM/SC_CLK/SPI0_ MOSI0 PB./STADC/TM0/INT0/SC_PWR PE. PB./SPI_SS/TM/SC_RST/INT0 PE. Table - Pin Assignment for NANO0 Feb., 0 Page of Rev.0

9 NUTINY-SDK-NANO0 USER MANUAL NANO0. NuTiny-SDK-NANO0 PCB Placement Users can refer to Figure - for the NuTiny-SDK-NANO0 PCB placement and Figure - for the NuTiny-SDK-NANO0_TNLCD PCB placement. Figure - NuTiny-SDK-NANO0 PCB Placement Figure - NuTiny-SDK-NANO0_TNLCD PCB Placement Feb., 0 Page of Rev.0

10 NUTINY-SDK-NANO0 USER MANUAL NANO0 HOW TO START NUTINY-SDK-NANO0 ON THE KEIL ΜVISION IDE. Keil uvision IDE Software Download and Install Please visit the Keil company website ( to download the Keil μvision and install the RVMDK. IDE. Nuvoton Nu-Link Driver Download and Install Please visit the Nuvoton company NuMicro website ( to download NuMicro Keil μvision IDE driver file. When the Nu-Link driver has been well downloaded, please unzip the file and execute the Nu-Link_Keil_Driver.exe to install the driver.. Hardware Setup The hardware setup is shown as Figure -. Figure - Hardware Setup Feb., 0 Page 0 of Rev.0

11 NUTINY-SDK-NANO0 USER MANUAL NANO0. Example Program This example demonstrates the ease of downloading and debugging an application on a NuTiny- SDK-NANO0 board. It can be found on Figure - list directory and downloaded from Nuvoton NuMicro website. Directory C:\Nuvoton\BSP Library\Nano00B_Series_BSP_CMSIS_v.0.00\SampleCode\NUTINY-EVB- NANO0\LCD_DEMO\KEIL Project File Figure - Example Directory To use this example: Connects the NuTuny-SDK-NANO0_TNLCD to NuTiny-SDK-NANO0. The LCD panel will display a NUVOTON logo. Start μvision Project-Open Open the SYS.uvproj project file Project - Build Compile and link the SYS application Flash Download Program the application code into onchip Flash ROM Start debug mode Using the debugger commands, you may: Review variables in the watch window Single step through code Reset the device Run the application Feb., 0 Page of Rev.0

12 NUTINY-SDK-NANO0 USER MANUAL NANO0 HOW TO START NUTINY-SDK-NANO0 ON THE IAR EMBEDDED WORKBENCH... IAR Embedded Workbench Software Download and Install Please connect to IAR company website ( to download the IAR Embedded Workbench and install the EWARM. Nuvoton Nu-Link Driver Download and Install Please visit the Nuvoton company NuMicro website ( ) to download the NuMicro IAR EWARM Driver file. When the Nu-Link driver has been well downloaded, please unzip the file and execute the Nu-Link_Keil_Driver.exe to install the driver. Hardware Setup The hardware setup is shown as Figure -. Figure - Hardware Setup Feb., 0 Page of Rev.0

13 NUTINY-SDK-NANO0 USER MANUAL NANO0. Example Program This example demonstrates the ease of downloading and debugging an application on a NuTiny-SDK-NANO0 board. It can be found on Figure - list directory and downloaded from Nuvoton NuMicro website. Directory C:\Nuvoton\BSP Library\Nano00B_Series_BSP_CMSIS_v.0.00\SampleCode\NUTINY-EVB- NANO0\LCD_DEMO\IAR Project File Figure - Example Directory To use this example: Connects the NuTuny-SDK-NANO0_TNLCD to NuTiny-SDK-NANO0. The LCD panel will display a NUVOTON logo. Start IAR Embedded Workbench Project Download and Debug Program the application code into on-chip Flash ROM File-Open-Workspace Open the SYS.eww workspace file Single step through code Reset the device Project - Make Compile and link the SYS application Run the application Feb., 0 Page of Rev.0

14 NUTINY-SDK-NANO0 USER MANUAL ICE Interface Crystal Reset Circuit From ICE Bridge's USB Power PIN PIN PIN PE. PE. PIN PIN PE. PE. PIN PIN PE.0 PB. PIN PIN PE. PVSS PIN PIN PIN PIN PE. PF. PIN PIN0 0 NC PF. PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN RESET PIN PIN PIN PIN XT_Out PIN PIN XT_In PIN PIN0 PIN PIN PB. 0 PIN0 PIN PC. 0 PIN0 PIN PC. 0 PIN0 PIN PC. 0 PIN0 PIN PC. 0 PIN0 PIN PD. 0 PIN0 PIN PD. PIN0 PIN 0 PIN0 PIN PE. PD. 0 PIN0 PIN0 0 VLCD PD. 0 PIN0 PIN NC PD. 00 PIN00 PIN PE. PD.0 PIN PIN PIN PIN PB.0 PIN PB. VREF TICE_RST XTAL XTAL Tit le Size Docum ent Num ber Rev Dat e: Sheet of NANO0 NUTINY-SDK-NANO0 SCHEMATIC. NuTiny-EVB-NANO0 Schematic VDD R 0K SW 00R TICE_RST SW C PUSH BUTTON 0uF/0V TANT-A JP VCC(A) TICE_DAT TICE_CLK TICE_RST 0 HEADER PX HEADER PX C R 0pF X 00C MHz R 00R XTAL- M/DNE 00R C 0pF 00C C pf X 00C.KHz XTAL- XTAL XTAL XKO VCC(B) VCC(A) D SSA RB00L TICE_DAT TICE_DAT TICE_CLK TICE_CLK TICE_RST TICE_RST VDD DVDD R VDD 0 00R U C PIN 0uF/0V PIN PE. TANT-A PIN PB. PIN PB. PIN PB. XKO PIN NC XKI PIN XO PIN XI PIN NC PIN0 0 PA. PIN PA.0 PIN PA. PIN PA. PIN PD. PIN PD. PIN PD.0 PIN PD. PIN PD. PIN PD. PIN0 0 PB. PIN PB. DVDD PIN PB. C PIN PB. PIN NC PIN LDO PIN NC 0uF/0V PIN NC TANT-A PIN VDD PIN NC PIN0 0 VSS PIN VSS PIN VSS VSS DVDD CB 0.uF VSS PE. DVDD CB C 0.uF uf NC VDD 0 NC VSS VSS VBUS VDD USB_DM USB_DP PB.0 PB. PB. PB. PD. 0 PD. PD. PD. PC. PC. PC. PC. PC. PC.0 NC NC NANO0_LQFP NC 0 DVDD CB 0.uF C 0.uF AVDD NC PB. PA. PA. PA. PA. PA. PA. 0 PA. PA.0 AVSS AVSS VSS VSS NC VDD NC ICE_CK/PF. 0 ICE_DAT/PF.0 PA. PA. PA. PA. PC. PC. PC.0 PC. PC. 0 PC. PE.0 PE. PE. PE. PE. C uf PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN nint0 SW SW PUSH BUTTON DVDD TICE_CLK TICE_DAT DVDD CB 0.uF TICE_RST PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN DVDD PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN00 PIN0 PIN0 PIN0 PIN0 PIN0 PIN0 PIN0 PIN0 PIN0 PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN[..] C pf 00C XKI VDD VDD C uf C 0.uF C0 uf TP SIP/P TP SIP/P TP SIP/P R 0 00R JP HEADER PX HEADER PX IO KPT-0 KP-0 JP PIN HEADER PX HEADER PX NuTiny-EVB-Nano0-LQFP V. Custom Friday, December 0, 0 NANO0KEBN.SCH V. Feb., 0 Page of Rev.0

15 NANO0 Feb., 0 Page of Rev.0 NUTINY-SDK-NANO0 USER MANUAL GPIO for pin Schematic. PIN PIN PIN PIN PIN[..] PIN PIN PIN PIN PIN PIN PIN JP HEADER PX PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN JP HEADER PX PIN0 PIN PIN PIN PIN0 PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN0 PIN0 PIN0 PIN0 PIN PIN PIN PIN0 PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN0 PIN0 PIN PIN0 PIN VBUS PIN0 R 00R USB_DP L L00 R 00R J mini USB pin USB_MINI_B GND NC DP DM VCC SHIELD SHIELD SHIELD SHIELD PIN0 PIN PIN PIN PIN0 PIN0 PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN00 PIN PIN PIN PIN USB_DM PIN PIN PIN PIN0 PIN0 PIN0 PIN0 PIN0 PIN JP HEADER PX PIN0 PIN PIN0 U RTA-.V IN GND OUT OUT VCC(B) CT 0uF/0V TANT-A Tit le Size Docum ent Num ber Rev Dat e: Sheet of OTHER.SCH V. NuTiny-EVB-Nano0-LQFP V. Custom Friday, December 0, 0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN0 PIN PIN PIN PIN PIN PIN0 PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN JP HEADER PX PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN0 PIN00 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN0 PIN PIN PIN0 PIN0 PIN PIN PIN PIN PIN0 PIN PIN0 PIN0 PIN0 PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN00 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN JP HEADER PX,.00mm PIN PIN PIN PIN PIN0 PIN PIN JP HEADER PX,.00mm JP HEADER PX,.00mm PIN JP HEADER PX,.00mm 0 0 0

16 NUTINY-SDK-NANO0 USER MANUAL Reset Circuit IN GND OUT (RED) (YELLOW) (RED) (GREEN) OUT IDLE Crystal BUSY POWER ADAVSS DEBUG 0 0 VBUS VDD D- D+ PB0/RX0 PB/TX0 PB/RTS0 PB/CTS0 PC/SDO00 PC/SDI00 PC/SPCLK0 PC0/SS00 PE PB/TM PB0/SS0/TM PB/SS/TM STADC/TM0/PB PVSS VDD VSS 0 /RESET XT_In XT_Out INT/PB CPP/PC CPN/PC CPP0/PC CPN0/PC AVDD ADC/PA 0 ADC/PA ADC/PA ICE_RST M_I M_O ICE CONNECT IF MCU and USB Tit le ADAVSS Size Docum ent Num ber Rev Dat e: Sheet of NANO0. Nu-Link-Me Schematic VCC VCC VCC VCC USBVBUS U RTA-.V VCC CT 0uF/0V TANT-A VCC icel L00 icel L00 AVDD iced SSA RB00L icejp ICE_DAT ICE_CLK ICE_RST HEADER PX HEADER PX RTIDA 00K 00R RICK 00K 00R TICE_DAT TICE_CLK TICE_RST VCC(A) TICE_DAT TICE_CLK TICE_RST iced SSA RB00L ICER 0 00R icejp 0 HEADER PX HEADER PX TP SIP/P icer M_O R00 M_I icer M/DNE R00 icec 0pF icex MHz XTAL- icec 0pF iceu VCC DI_DIR AVDD USB_D- USB_D+ icer 00R icer 00R TP SIP/P USBVBUS icej VCC SHIELD DM SHIELD DP SHIELD NC SHIELD GND mini USB pin USB_MINI_B USBVBUS TP SIP/P icel L00 ICELED ICPLED RED GREEN ICE ICP KPT-0 KP-0 KP-0 KPT-0 KPT-0 KP-0 icerp PR-0 PRA VCC VCC icect 0uF/0V TANT-A ICELED ICPLED RED GREEN icecb 0.uF 0 VDD VSS INT0/PB CPO/PB CPO0/PB XI XO ICSCL/PA ICSDA/PA0 IC0SCL/PA IC0SDA/PA RX/PB TX/PB RTS/PB CTS/PB LDO NUCSREAN PA/ADC PA/ADC PA/ADC PA/ADC PA0/ADC0 AVSS ICE_CK ICE_DAT 0 PA/PWM0 PA/PWM PA/PWM PA/PWM PC/SS0 PC/SPCLK PC0/SDI0 PC/SDO0 ICE_CLK ICE_DAT TICERST TICECLK RTDA 0 00R TP SIP/P RTDA 00R VCC RRSET RTCK 00K 00K 00R 00R TICEDAT RTDA 00K 00R KPT-0 KP-0 USBVBUS VCC icec uf icecb 0.uF USB_D+ USB_D- DO_DIR icer 0K R00 ICE_RST VCC VCC(A) VCC VCC(A) icec 0uF/0V TANT-A VCC icecb 0.uF TICEDAT iceu VCCA VCCB A B A B GND DIR SNLVCTDCUR SSOP- TICE_DAT DI_DIR TICECLK TICERST iceu VCCA VCCB A B A B GND DIR SNLVCTDCUR SSOP- TICE_CLK TICE_RST DO_DIR VCC(A) icecb 0.uF Nu-Link-Me V. Custom Wednesday, June, 0 ICE_LQFP.SCH V. Feb., 0 Page of Rev.0

17 NANO0 Feb., 0 Page of Rev.0 NUTINY-SDK-NANO0 USER MANUAL NuTiny-SDK-NANO0_TNLCD Schematic. PIN SEG PIN SEG SEG PIN SEG PIN SEG PIN PIN SEG PIN0 SEG SEG PIN V PIN SEG PIN COM0 PIN SEG PIN SEG PIN PIN SEG COM PIN COM PIN SEG PIN SEG PIN SEG PIN U TN LCD X SEG PIN SEG PIN SEG PIN DH PIN SEG0 PIN PIN SEG SEG PIN0 SEG PIN PIN SEG0 PIN SEG PIN0 SEG SEG0 PIN C uf SEG PIN C uf V PIN PIN SEG0 SEG PIN PIN SEG PIN SEG SEG PIN DH PIN PIN SEG SEG PIN C uf V PIN COM PIN PIN SEG Tit le Size Docum ent Num ber Rev Dat e: Sheet of X TN LCD glass.sch V.0 NuTiny-EVB-TNLCD-Nano0-LQFP V.0 Custom Thursday, July, 0 PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN C uf PIN0 PIN PIN PIN PIN PIN0 PIN0 PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN0 PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN PIN JP HOLDER PX,.00mm JP HOLDER PX,.00mm SEG PIN SEG PIN0 SEG PIN0 SEG PIN0 SEG PIN0 JP HOLDER PX,.00mm JP HOLDER PX,.00mm 0 0 0

18 NUTINY-SDK-NANO0 USER MANUAL NANO0 REVISION HISTORY Date Revision Description Initially issued Change the value of C and C in the schematics from 0 pf to pf Updated the figure of NuTiny-SDK-NANO0 PCB Board in chapter.. Updated th descriptions in chapter.. Updated the example program descriptions in chapter and.. Updated NuTiny-SDK-NANO0 schematics in chapter. Feb., 0 Page of Rev.0

19 NUTINY-SDK-NANO0 USER MANUAL NANO0 Important Notice Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any malfunction or failure of which may cause loss of human life, bodily injury or severe property damage. Such applications are deemed, Insecure Usage. Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic energy control instruments, airplane or spaceship instruments, the control or operation of dynamic, brake or safety systems designed for vehicular use, traffic signal instruments, all types of safety devices, and other applications intended to support or sustain life. All Insecure Usage shall be made at customer s risk, and in the event that third parties lay claims to Nuvoton as a result of customer s Insecure Usage, customer shall indemnify the damages and liabilities thus incurred by Nuvoton. Feb., 0 Page of Rev.0