NuTiny-SDK-M058S User Manual

Transcription

1 ARM Cortex -M0 32-bit Microcontroller For NuMicro M058S Series The information described in this document is the exclusive intellectual property of Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton. Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system design. Nuvoton assumes no responsibility for errors or omissions. All data and specifications are subject to change without notice. For additional information or questions, please contact: Nuvoton Technology Corporation. Oct. 3, 203 of 6 Rev..00

2 Table of Contents Overview Introduction to NuTiny-SDK- M058S NuTiny-SDK- M058S Jumper Description Pin Assignment for Extended Connectors NuTiny-SDK-M058S PCB Placement Starting to Use NuTiny-SDK-M058S on the Keil μvision IDE Downloading and Installing Keil μvision IDE Software Downloading and Installing Nuvoton Nu-Link Driver Hardware Setup Smpl_NuTiny-M05 Example Program Starting to Use NuTiny-SDK-M058S on the IAR Embedded Workbench Downloading and Installing IAR Embedded Workbench Software Downloading and Installing Nuvoton Nu-Link Driver Hardware Setup Smpl_NuTiny-M05 Example Program NuTiny-EVB-M058S Schematics... 6 Downloading NuMicro Related Files from Nuvoton Website Downloading NuMicro Keil μvision IDE Driver Downloading NuMicro IAR EWARM Driver Downloading NuMicro M05 series BSP Software Library Revision History... 6 Oct. 3, of 6 Rev..00

3 Overview The NuTiny-SDK-M058S is a specific development tool for NuMicro M058S series by which users can develop and verify the application program easily. The NuTiny-SDK-M058S includes two portions: NuTiny-EVB-M058S (an evaluation board) and Nu-Link-Me (Debug Adaptor). With the NuTiny-SDK- M058S, users do not need additional ICE or debug equipment. 2 Introduction to NuTiny-SDK- M058S The following figure shows the NuTiny-SDK-M058S for M058S series, in which the left portion is called NuTiny-EVB-M058S and the right portion is Debug Adaptor called Nu-Link-Me. The NuTiny-EVB-M058S is similar to other development board. Users can use it to develop and verify applications to emulate the real behavior. In fact, the real chip M058S is mounted on the board. The NuTiny-EVB-M058S can be a real system controller to design user target system. The Nu-Link-Me is a Debug Adaptor which connects the USB port of your PC to your target system (via Serial Wired Debug Port) and allows you to program and debug embedded programs on the target hardware. To use the Nu-Link-Me Debug adaptor with Keil or IAR, please refer to Nuvoton NuMicro IAR ICE Driver User Manual or Nuvoton NuMicro Keil ICE Driver User Manual for details. LQFP-64 pin extended connector ICE Chip Reset Key IO LED Power LED LQFP-64 pin extended connector Target Chip ICE Chip UCB Connector Figure 2- NuTiny-SDK-M058S (Green PCB Board) Oct. 3, of 6 Rev..00

4 2. NuTiny-SDK- M058S Jumper Description 2.. Power Settings JP: Voltage connecter in NuTiny-EVB-M058S J2: USB port in Nu-Link-Me Model J USB Port J2 USB Port JP MCU Voltage Model X Connect to PC DC 3.3V output DC 3.3V Model 2 X X DC 2.5 V ~ 5.5 V Voltage by Input input X: Unused Debug Connectors JP3: Target ICE Connector in NuTiny-EVB-M058S JP9: Nuvoton ICE Connector in Nu-Link-Me 2..3 USB Connectors J2: Mini USB Connecter in Nu-Link-Me 2..4 Extended Connectors JP5, JP6, JP7 and JP8: Show all of chip pins in NuTiny-EVB-M058S 2..5 Buttons SW: Reset button in NuTiny-EVB-M058S 2..6 Power Connectors JP: VCC connecter in NuTiny-EVB-M058S JP2: GND connecter in NuTiny-EVB-M058S Oct. 3, of 6 Rev..00

5 2.2 Pin Assignment for Extended Connectors The NuTiny-EVB- M058S provides the M058SSAN target chip on board and the extended connectors (JP5, JP6, JP7 and JP8) for LQFP64-pin. The following table is the pin assignment for M058SSAN. Pin No Pin Name Pin No Pin Name 0 P.5, MOSI_0, AIN5 33 P P.6, MISO_0, AIN6 34 P P.7, SPICLK0, AIN7 35 P /RST 36 P4.4, SCL 05 P3.0, RXD 37 P4.5, SDA 06 P5.0, T0EX 38 P4.6, ICE_CLK 07 P5., TEX 39 P4.7, ICE_DAT 08 P5.2, SDA0 40 P P5.3, SCL0 4 P6. 0 P3., TXD 42 P6.2 P3.2, /INT0, STADC, T0EX 43 P6.3 2 P3.3, /INT, TEX 44 P0.7, SPICLK0 3 P3.4, T0, SDA0 45 P0.6, MISO_0 4 P3.5 T SCL0, CKO 46 P0.5, MOSI_0 5 P4.3, PWM3 47 P0.4, SPISS0 6 P3.6, CKO 48 P4., PWM, T3EX 7 P P0.3, RTS, RXD 8 XTAL2 50 P0.2, CTS, TXD 9 XTAL 5 P0. 20 VSS 52 P0.0 2 VDD 53 VSS 22 LDO_CAP 54 VDD 23 P P P P P P P P P2.0, PWM0 59 P.0, T2, AIN0 28 P2., PWM 60 P., T3, AIN 29 P2.2, PWM2 6 P.2, AIN2 30 P2.3, PWM3 62 P.3, AIN3 3 P P.4, SPISS0, AIN4 32 P4.0, PWM0 64 P4.2, PWM2 Table 2- Pin Assignment for M058SSAN Oct. 3, of 6 Rev..00

6 2.3 NuTiny-SDK-M058S PCB Placement The following figure shows the NuTiny-SDK- M058S PCB placement. Figure 2-2 NuTiny-SDK-M058S PCB Placement Oct. 3, of 6 Rev..00

7 3 Starting to Use NuTiny-SDK-M058S on the Keil μvision IDE 3. Downloading and Installing Keil μvision IDE Software Please visit the Keil company website ( to download the Keil μvision IDE and install the RVMDK. 3.2 Downloading and Installing Nuvoton Nu-Link Driver Please visit Nuvoton NuMicro website ( to download the NuMicro Keil μvision IDE Driver file. Please refer to section 6. for the detailed download flow. After the Nu-Link driver is downloaded, please unzip the file and execute the Nu- Link_Driver_for_keil_RVMDK_V zip to install the driver. 3.3 Hardware Setup The hardware setup is shown in the following figure. Figure 3- NuTiny-SDK-M058S Hardware Setup Oct. 3, of 6 Rev..00

8 3.4 Smpl_NuTiny-M05 Example Program This example demonstrates how to download and debug an application on a NuTiny-SDK-M058S board. The example file can be found in the directory list shown in the following figure. Directory Project File To use this example: Figure 3-2 Smpl_NuTiny-M05 Example Directory Start μvision Project Open Open the Smpl_NuTiny-M05.uvproj project file Project Build Compile and link the Smpl_NuTiny- M05 application Flash Download Program the application code into onchip Flash ROM Start Debug mode When using the debugger commands, you may: Review variables in the watch window Single step through code Reset the device Run the application The P3.6 LED on the NuTiny-EVB- M058 board will be toggled on. Oct. 3, of 6 Rev..00

9 4 Starting to Use NuTiny-SDK-M058S on the IAR Embedded Workbench 4. Downloading and Installing IAR Embedded Workbench Software Please visit the IAR company website ( to download the IAR Embedded Workbench and install the EWARM. 4.2 Downloading and Installing Nuvoton Nu-Link Driver Please visit the Nuvoton Company NuMicro website ( to download the NuMicro IAR ICE Driver User Manual file. Please refer to section 6.2 for the detail download flow. When the download had finished, please unzip the file and execute the Nu_Link_Driver_for_IAR_RVMDK_V zip to install the driver. 4.3 Hardware Setup The hardware setup is shown in the following figure. Figure 4- NuTiny-SDK-M058S Hardware Setup Oct. 3, of 6 Rev..00

10 4.4 Smpl_NuTiny-M05 Example Program The example demonstrates how to download and debug an application on a NuTiny-SDK-M058S board. The example can be found in the directory list shown in the following figure. (Sample code can be downloaded from Nuvoton website). Directory Project File To use this example: Figure 4-2 Smpl_NuTiny-M05 Example Directory Start IAR Embedded Workbench File-Open-Workspace Open the Smpl_NuTiny-M05.eww workspace file Project Download and Debug Program the application code into onchip Flash ROM Single step through code Project - Make Compile and link the Smpl_NuTiny- Reset the device M05 application Run the application The P3.6 LED on the NuTiny-EVB-M058S board will be toggled on. Oct. 3, of 6 Rev..00

11 ADAVSS P7 7 D2MO P8 8 P P64 D2MI P9 9 P7.0/TTAL2 PWM2+/P P63 P20 20 P7./XTAL SPISS0/AIN4/P.4 62 P62 P2 2 VSS AIN3/P.3 6 P6 P22 22 VDD AIN2/P.2 60 P60 P23 23 LDO T3/AIN/P. 59 P59 P24 24 P5.4 T2/AIN0/P.0 58 P58 P25 25 P5.5 P P57 P26 26 P5.6 P6.6 P27 27 P5.7 Vref 56 P56 P55 P28 28 P2.0/PWM0 P54 P29 P53 P30 30 P2.2/PWM2 52 P52 P3 3 P2.3/PWM3 P0.0 5 P5 P32 32 P2.4/PWM4 P0. 50 P50 P4.0/PWM0+/T2EX TXD+/CTS0/P P49 RXD+/RTS0/P0.3 5 NuTiny-EVB-M058S Schematics D R ICERST SW 0K PUSH BOTTON SW C 0uF/0V TANT-A RESET Reset TICECON TICECON TICEDAT TICEDAT TICECLK TICECLK TICERST TICERST D ICECON ICEDAT ICECLK ICERST JP 2 HEADER 2 P22 TP SIP/P DAVDD RESET TP2 SIP/P JP D ICECON ICEDAT ICECLK ICERST JP2 2 HEADER 2 GND TP3 SIP/P DAVDD D HEADER 5X2 ICE INTERFACE C3 20p C0603 C5 20p C0603 R2 33 D2MO X2 2MHz XTAL3- D2MI Crystal DAVDD L L0603 L2 L0603 D ADAVSS U6 55 AVDD 54 VDD VSS 53 P6 D R3 500 IO KPT KP-202 D PR 500 POWER KPT KP-202 P P2 P3 RESET P4 P5 P6 P7 P8 P9 P0 P P2 P3 P4 P5 P P.5/AIN5/MOSI P.6/AIN6/MISO P.7/AIN7/SPICLK RST P3.0/RXD AVSS P5. P5.2 P5.3 P3./TXD P3.2/INT0/STADC/T0EX P3.3/INT/TEX P3.4/T0/SDA0 P3.5/T/SCL0 6 P4.3/PWM3+ P3.6/CKO 48 T3EX/PWM+/P4. 47 SPISS0+/P MOSI+/P MISO+/P SPICLK+/P P P6.2 4 P6. 40 P ICE_DAT/P4,7 38 ICE_CLK/P I2CSDA/P I2CSCL/P PWM7/P PWM6/P PWM5/P2.5 ICEDAT ICECLK P48 P47 P46 P45 P44 P43 P42 P4 P40 P39 P38 P37 P36 P35 P34 P33 P P3 P5 P7 P9 P P3 P5 JP P2 P4 P6 P8 P0 P2 P4 P6 P7 P9 P2 P23 P25 P27 P29 P3 JP P8 P20 P22 P24 P26 P28 P30 P32 29 P2./PWM HEADER 8X2 HEADER 8X2 M058SSAN_LQFP64 P33 P35 P37 P39 P4 P43 P45 P47 JP P34 P36 P38 P40 P42 P44 P46 P48 P49 P5 P53 P55 P57 P59 P6 P63 JP P50 P52 P54 P56 P58 P60 P62 P64 HEADER 8X2 HEADER 8X2 D CT uf/6.3v TANT-R Title Nuvoton NuTiny-EVB-M058SSAN(LQFP64) Size Document Number Rev A3 2.0 Wednesday, July 0, 203 Date: Sheet of Oct. 3, 203 of 6 Rev..00

12 VBUS VBUS VDD33 D- D+ PB0/RX0 PB/TX0 PB2/RTS0 PB3/CTS0 PC3/SDO00 PC2/SDI00 PC/SPCLK0 PC0/SS00 PE5 PB/TM3 PB0/SS0/TM2 PB9/SS/TM VDD VSS /RESET XT_In XT_Out INT/PB5 CPP/PC4 CPN/PC5 CPN0/PC7 53 CPP0/PC6 ADC7/PA7 ADC6/PA6 ADC/PA5 5 AVDD USB_D+ USB_D IN GND OUT OUT 2 3 NUC_RST# 2M_I 2M_O TICECON ICE KPT-202 ICELED 2 KP-202 ISPLED 2 RED TICECON ICP KPT-202 KP-202 IDLE KPT KP-202 BUSY KPT-202 GREEN 2 KP-202 CT2 0uF/6.3V TANT-R ICECON CB 0.u C0603 RP 8P4R P4RA ICELED ISPLED RED GREEN U2 2 INT0/PB4 3 CPO/PB3 4 CPO0/PB2 5 X32I 6 X32O 7 I2CSCL/PA 8 I2CSDA/PA0 9 I2C0SCL/PA9 0 I2C0SDA/PA8 RX/PB4 2 TX/PB5 3 RTS/PB6 4 CTS/PB7 5 LDO 6 VDD VSS PVSS STADC/TM0/PB8 64 PVSS 63 NUC2SRE3AN NUC_RST# AVDD R8 0K ICE_RST C7 0uF/0V TANT-A 48 PA4/ADC4 47 PA3/ADC3 46 PA2/ADC2 45 PA/ADC 44 PA0/ADC0 AVSS ICE_CK 4 ICE_DAT 40 PA2/PWM0 39 PA3/PWM 38 PA4/PWM2 37 PA5/PWM3 36 PC8/SS0 35 PC9/SPCLK 34 PC0/SDI0 33 PC/SDO0 ICE CONNECT IF ICE_CLK ICE_DAT TICERST TICECLK 2M_O 2M_I TICEDAT TICECLK TICERST R K RTDA2 RTDA3 TICEDAT TICECLK TICERST RTCK 00K ADAVSS TICEDAT JP9 TICECON C8 20p C0603 X3 2MHz XTAL3- C9 20p RTDA 00K D2 SS24A RB060L C0603 HEADER 5X2 RRSET 00K TICERST AVDD USBVBUS L5 L0603 C0 u C0603 CB2 0.u C0603 R 33 R2 33 USBVBUS DM DP 2 VCC 3 DM 4 DP 5 NC GND J2 mini USB 5pin SHIELD 6 SHIELD 7 SHIELD 8 SHIELD 9 USB_MINI_B L4 HEADER 5 JP ICE_DAT ICE_CLK ICE_RST RTIDA 00K DEBUG RICK 00K L6 L0603 L0805 ADAVSS VCC GND USBVBUS DM DP JP HEADER 4 UP6 RT964A-3.3v P5V USBVBUS PD2 SS24A 2 RB060L JPR HEADER 3 CP 0uF/0V TANT-B P3V Title Nuvoton NuTiny-EVB-M058SSAN(LQFP64) Size Document Number Rev A3 2.0 Date: Wednesday, July 0, 203 Sheet of Oct. 3, of 6 Rev..00

13 6 Downloading NuMicro Related Files from Nuvoton Website 6. Downloading NuMicro Keil μvision IDE Driver Step Visit the Nuvoton NuMicro Website: Step2 Step3 Downloading the file Step4 Download the NuMicro Keil uvision IDE driver. Oct. 3, of 6 Rev..00

14 6.2 Downloading NuMicro IAR EWARM Driver Step Visit the Nuvoton NuMicro Website: Step2 Step 3 Downloading the file Step 4 Download the NuMicro IAR Embedded Workbench driver. Oct. 3, of 6 Rev..00

15 6.3 Downloading NuMicro M05 series BSP Software Library Step Visit the Nuvoton NuMicro Website: Step2 Step3 Download the NuMicro M05 series software library. Oct. 3, of 6 Rev..00

16 7 Revision History Revision Date Description.00 Oct.3, 203 Initial release Important Notice Nuvoton products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Furthermore, Nuvoton products are not intended for applications wherein failure of Nuvoton products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Nuvoton customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Nuvoton for any damages resulting from such improper use or sales. Please note that all data and specifications are subject to change without notice. All the trademarks of products and companies mentioned in this datasheet belong to their respective owners. Oct. 3, of 6 Rev..00