for NuMicro NUC123 Series

Transcription

1 ARM Cortex -M0 -BIT MICROCONTROLLER for NuMicro NUC1 Series The information described in this document is the exclusive intellectual property of Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton. Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system design. Nuvoton assumes no responsibility for errors or omissions. All data and specifications are subject to change without notice. For additional information or questions, please contact: Nuvoton Technology Corporation. Aug. 0, 01 Revision V1.0

2 Table of Contents 1 Overview... Introduction to NuTiny-SDK-NUC Jumper Description.... Pin Assignment for Extended Connectors PCB Placement... 6 Starting to Use NuTiny-SDK-NUC1 with Keil μvision IDE Downloading and Installing Keil uvision IDE Software Downloading and Installing Nuvoton Nu-Link Driver Hardware Setup Smpl_NuTiny-NUC1 Example Program... 8 Starting to Use NuTiny-SDK-NUC1 with IAR Embedded Workbench Downloading and Installing IAR Embedded Workbench Software Downloading and Installing Nuvoton Nu-Link Driver Hardware Setup Smpl_NuTiny-NUC1 Example Program NuTiny-SDK-NUC1 Schematics NuTiny-EVB-NUC1 Schematic Nu-Link-Me Schematic Downloading NuMicro Related Files from Nuvoton Website Downloading NuMicro Keil μvision IDE Driver Downloading NuMicro IAR EWARM Driver Downloading NuMicro NUC1 Series BSP Software Library Revision History Aug. 0, 01 Revision V1.0

3 1 Overview The NuTiny-SDK-NUC1 is a specific development tool for NuMicro NUC1 series. User can use NuTiny-SDK- NUC1 to develop and verify the application program easily. The NuTiny-SDK-NUC1 includes two parts: NuTiny- EVB-NUC1 and Nu-Link-Me. The NuTiny-EVB-NUC1 is the evaluation board and Nu-Link-Me is its Debug Adaptor. Therefore, user does not need other additional ICE or debug equipment. Introduction to NuTiny-SDK-NUC1 The NuTiny-SDK-NUC1 uses the NUC1SDAN0 as the target microcontroller. Figure -1 shows the NuTiny-SDK- NUC1 for NUC1 series, in which the left portion is called NuTiny-EVB-NUC1 and the right portion is called Nu- Link-Me. The NuTiny-EVB-NUC1 is similar to other development boards. User can use it to develop and verify applications to emulate the real behavior. The on-board chip covers NUC1 series features. The NuTiny-EVB-NUC1 can be a real system controller to design users target systems. The Nu-Link-Me is a Debug Adaptor, which connects your PC's USB port to your target system (via Serial Wired Debug port) and allows you to program and debug embedded programs on the target hardware. To use the Nu-Link-Me Debug Adaptor with IAR or Keil, please refer to the Nuvoton NuMicro IAR ICE Driver User Manual or Nuvoton NuMicro Keil ICE Driver User Manual for details. The two documents will be stored in the local hard disk when each driver is installed. Figure -1 NuTiny-SDK-NUC1 (Purple PCB Board) Aug. 0, 01 Revision V1.0

4 .1 Jumper Description.1.1 Power Settings J1: USB port in NuTiny-EVB-NUC1 JP1: VCC voltage connecter in NuTiny-EVB-NUC1 J: USB port in Nu-Link-Me POWER Mode J USB Port J1 USB Port JP1 VCC MCU Voltage Mode 1 Connected to PC X DC. V or 5 V DC. V or 5 V [1] Output [1] Mode X Connect to PC DC.8 V or 5 V DC.8 V or 5 V [] Output [] Mode X X DC.5 V ~ 5.5 V Input DC.5 V ~ 5.5 V Decided by JP1 VCC Input X: Unused. Note [1]: It depends on the setting (VCC via connecting to. V or 5 V) at JPR jumper in the Nu-Link-Me. Note []: A diode device (.8 V) must be put or both pins should be short (5 V) at D1 in the NuTiny-EVB-NUC1..1. Debug Connectors JP: The connector in the target board (NuTiny-EVB-NUC1) for connecting with Nuvoton ICE adaptor (Nu- Link or Nu-Link-Me) JP9: The connector in the ICE adaptor (Nu-Link-Me) for connecting with a target board (e.g. NuTiny-EVB- NUC1).1. USB Connectors J1: Mini USB connector in NuTiny-EVB-NUC1 for application use J: Mini USB connector in Nu-Link-Me connected to a PC USB port.1. Extended Connectors JP5, JP6, JP7 and JP8: Show all chip pins in NuTiny-EVB-NUC1.1.5 Reset Button SW1: Reset button in NuTiny-EVB-NUC1.1.6 Power Connectors JP1: VCC connector in NuTiny-EVB-NUC1 JP: GND connector in NuTiny-EVB-NUC1 Aug. 0, 01 Revision V1.0

5 . Pin Assignment for Extended Connectors The NuTiny-EVB-NUC1 provides the NUC1SDAN0 target chip on board and the extended connectors (JP5, JP6, JP7 and JP8) for LQFP 6-pin. No Pin Name No Pin Name No Pin Name No Pin Name 1 PB.1/ INT 0 17 VBUS VSS 9 PD.0/ADC0/ SPISS0/SPISS11 PB.1 18 VDD PC.1/MOSI11/ PD.1/ADC1/ 50 PWM/CLKO SPICLK/SPISS01 PB.1/SPISS10/ PC.1/MISO11/ PD./ADC/ 19 D CLKO PWM/ISMCLK MISO0/MISO01 PA.11/SPICLK1/ PD./ADC/ 0 D+ 6 PC.11/MOSI10 5 MOSI0/IC1SCL MOSI0/MOSI01 5 PA.10/MISO10/ 1 PB.0/RXD0 MISO0/IC1SDA 7 PC.10/MISO10 5 PD./ADC/ MISO1 6 PD.8/MOSI10 PB.1/TXD0 8 VDD 5 PD.5/ADC5/ MOSI1 7 PD.9 8 PD.10/CLKO PB./RTS0/ TEX PB./CTS0/ TEX 9 PD.11/ INT 1 5 PC.5/MOSI01/ PB./RXD1/ SPISS0/SPISS11 PB.5/TXD1 SPICLK PB.6/RTS1 MOSI0 PB.7/CTS1 MISO0 TXD0 6 PC./MISO01/ RXD0 7 PC./MOSI00/ ISDO 8 PC./MISO00/ ISDI 9 PC.1/SPICLK0/ ISBCLK 1 LDO 0 PC.0/SPISS00/ ISLRCLK 15 VDD 1 PB.10/SPISS01/ 9 PC.9/SPICLK1 55 PB.15/ INT 1/ T0EX 0 PC.8/SPISS10 56 PF.0/XT1_OUT 1 PA.15/PWM/ ISMCLK/CLKO 57 PF.1/XT1_IN VSS 58 /RESET PA.1/PWM 59 VSS PA.1/PWM1 60 VDD 5 PA.1/PWM ICE_DAT 6 PF./ADC6/ IC0SDA/PSDAT PF./ADC7/ IC0SCL/PSCLK TM 7 ICE_CK 6 PVSS 16 VSS PB.9/SPISS11/ TM1 8 AVDD 6 PB.8/TM0 Table -1 NUC1SDAN0 LQFP 6-pin Assignment for Extended Connectors Aug. 0, 01 5 Revision V1.0

6 . PCB Placement The following figure shows the NuTiny-SDK-NUC1 PCB placement. Figure - NuTiny-SDK-NUC1 PCB Placement Aug. 0, 01 6 Revision V1.0

7 Starting to Use NuTiny-SDK-NUC1 with Keil μvision IDE.1 Downloading and Installing Keil uvision IDE Software Please visit the Keil company website ( to download the Keil μvision IDE and install the RVMDK.. Downloading and Installing Nuvoton Nu-Link Driver Please visit Nuvoton NuMicro website ( to download the NuMicro Keil μvision IDE driver file. Please refer to 6.1 Downloading NuMicro Keil μvision IDE Driver for the detailed download flow. After the Nu-Link driver is downloaded, please unzip the file and execute the Nu-Link_Keil_Driver.exe to install the driver.. Hardware Setup The hardware setup is shown in the following figure. Figure -1 NuTiny-SDK-NUC1 Hardware Setup Aug. 0, 01 7 Revision V1.0

8 . Smpl_NuTiny-NUC1 Example Program This example, as shown in the directory in Figure -, demonstrates downloading and debugging an application on a NuTiny-SDK-NUC1 board. The example file can be downloaded from Nuvoton NuMicro website as described in 6. Downloading NuMicro NUC1 Series BSP Software Library. Directory Project File Figure - Smpl_NuTiny_NUC1 Example Directory To use the example: The PB. LED on the NuTiny-EVB-NUC1 board will be toggled On. Start μvision Project - Open Open the Smpl_NuTiny_NUC1.uvproj project file Start debug mode Using the debugger commands, you may: Review variables in the watch window Project - Build Compile and link the Smpl_NuTiny-NUC1 application Flash Download Program the application code into on-chip Flash ROM Single step through code Reset the device Run the application Aug. 0, 01 8 Revision V1.0

9 Starting to Use NuTiny-SDK-NUC1 with IAR Embedded Workbench.1 Downloading and Installing IAR Embedded Workbench Software Please connect to IAR company website ( to download the IAR Embedded Workbench and install the EWARM.. Downloading and Installing Nuvoton Nu-Link Driver Please connect to the Nuvoton Company NuMicro website ( to download NuMicro IAR ICE driver user manual file. Please refer to Chapter 6. for the detail download flow. When the Nu-Link driver has been well downloaded, please unzip the file and execute the Nu-Link_IAR_Driver.exe to install the driver.. Hardware Setup The hardware setup is shown in the following figure. Figure -1 NuTiny- SDK-NUC1 Hardware Setup Aug. 0, 01 9 Revision V1.0

10 . Smpl_NuTiny-NUC1 Example Program This example, as shown in the directory in Figure -, demonstrates downloading and debugging an application on a NuTiny-SDK-NUC1 board. The example file can be downloaded from Nuvoton NuMicro website as described in 6. Downloading NuMicro NUC1 Series BSP Software Library. Directory Project File Figure - Smpl_NuTiny-NUC1 Example Directory To use this example: The PB. LED will toggle on the NuTiny-EVB-NUC1 board. Start IAR Embedded Workbench File-Open-Workspace Open the Smpl_NuTiny_NUC1.eww workspace file Project Download and Debug Program the application code into on-chip Flash ROM Project - Make Compile and link the Smpl_NuTiny-NUC1 application Single step through code Reset the device Run the application Aug. 0, Revision V1.0

11 USBD- USBD+ P17 P18 P19 P0 P1 P P P P5 P6 P7 P8 P9 P0 P1 P VBUS VDD D- D+ PB.0/RXD0 PB.1/TXD0 PB./RTS0/TEX PB./CTS0/TEX PC.5/MOSI01/TXD0 PC./MISO01/RXD0 PC./MOSI00/ISDO PC./MISO00/ISDI PC.1/SPICLK0/ISBCLK PC.0/SPISS00/ISLRCLK PB.10/SPISS01/TM PB.9/SPISS11/TM1 TM0/PB.8 PVSS ICE_CK/PSCLK/IC0SCL/ADC7/PF. ICE_DAT/PSDAT/IC0SDA/ADC6/PF. VDD VSS RESET XT1_IN/PF.1 XT1_OUT/PF.0 T0EX/INT1/PB.15 MOSI1/ADC5/PD.5 MISO1/ADC/PD. MOSI01/MOSI0/ADC/PD. MISO01/MISO0/ADC/PD. SPISS01/SPICLK/ADC1/PD.1 SPISS11/SPISS0/ADC0/PD RESET D1MI D1MO P6 P6 P6 P61 P60 P59 P58 P60 P57 P56 P55 P5 P5 P5 P51 P50 P9 5 NuTiny-SDK-NUC1 Schematics 5.1 NuTiny-EVB-NUC1 Schematic D R1 SW1 10K PUSH BOTTOM R060 SW C1 10uF/10V TANT-A ICERST RESET Reset TICEDAT TICEDAT TICECLK TICECLK TICERST TICERST D ICEDAT ICECLK ICERST JP1 1 HEADER JP 1 U6 JP D HEADER 1 ICEDAT ICECLK 5 6 ICERST HEADER 5X ICE INTERFACE D DAVDD L1 L060 C R 0p D1MO R060 C060 X 1MHz C5 XTAL-1 0p D1MI P1 P P P P5 P6 P7 P8 P9 P10 P11 P1 P1 P1 P15 P16 1 PB.1/INT0 PB.1 PB.1/SPISS10/CLKO 5 PA.11/IC1SCL/MOSI0/SPICLK1 6 PA.10/IC1SDA/MISO0/MISO10 7 PD.8/MOSI10 8 PD.9 9 PD.10/CLKO 10 PD.11/INT1 11 PB./RXD1/SPISS11/SPISS0 1 PB.5/TXD1/SPICLK 1 PB.6/RTS1/MOSI0 1 PB.7/CTS1/MISO0 15 LDO 16 VDD VSS 8 AVDD 7 ICE_CK 6 ICE_DAT 5 PWM0/PA.1 PWM1/PA.1 PWM/PA.1 VSS 1 CLKO/ISMCLK/PWM/PA.15 0 SPISS10/PC.8 9 SPICLK1/PC.9 8 VDD 7 MISO10/PC.10 6 MOSI10/PC.11 5 ISMCLK/PWM/MISO11/PC.1 CLKO/PWM/MOSI11/PC.1 VSS ICECLK ICEDAT DAVDD P8 P7 P6 P5 P P P P1 P0 P9 P8 P7 P6 P5 P P C060 Crystal CT1 1uF/6.V TANT-R D P10 D R5 IO1 KPT KP-01 R060 PR1 POWER1 500 KPT-01 R060 1 KP-01 DVBUS DM1 DP1 VCC JP 1 HEADER NUC1LQFP6 USBD- USBD+ R6 R060 R7 R060 DM1 DP1 DVBUS D1 NC 1 RB060L J1 mini USB 5pin 1 6 VCC SHIELD 7 DM SHIELD 8 DP SHIELD 9 5 NC SHIELD GND DVBUS USB_MINI_B L GND C6 L U C060 P1 P P5 P7 P9 P11 P1 P15 JP P P P6 P8 P10 P1 P1 P16 P17 P19 P1 P P5 P7 P9 P1 JP P18 P0 P P P6 P8 P0 P P P5 P7 P9 P1 P P5 P7 JP P P6 P8 P0 P P P6 P8 P9 P51 P5 P55 P57 P59 P61 P6 JP P50 P5 P5 P56 P58 P60 P6 P6 HEADER 8X HEADER 8X HEADER 8X HEADER 8X Title Nuvoton NU_TINY_1 Size Document Number Rev A 1.0 Date: Friday, August 10, 01 Sheet of Aug. 0, Revision V1.0

12 1 VBUS USB_D+ USB_D- 1 IN GND OUT OUT VBUS VDD D- D+ PB0/RX0 PB1/TX0 PB/RTS0 PB/CTS0 PC/SDO00 PC/SDI00 PC1/SPCLK0 PC0/SS00 PE5 PB11/TM PB10/SS01/TM PB9/SS11/TM1 ADC/PA5 ADC6/PA6 ADC7/PA7 AVDD CPN0/PC7 CPP0/PC6 CPN1/PC15 CPP1/PC1 INT1/PB15 XT1_Out XT1_In /RESET VSS1 VDD1 PVSS STADC/TM0/PB NUC_RST# 1M_I 1M_O 1 5. Nu-Link-Me Schematic ICE CONNECT IF D ICE1 KPT-01 ICELED 1 KP-01 ISPLED RED GREEN CT 10uF/6.V TANT-R ICP1 KPT-01 1 KP-01 IDLE1 KPT-01 1 KP-01 BUSY1 KPT-01 1 KP-01 CB1 0.1u C060 RP1 8PR PRA ICELED ISPLED RED GREEN U 1 INT0/PB1 CPO1/PB1 CPO0/PB1 PVSS XI XO IC1SCL/PA11 IC1SDA/PA10 IC0SCL/PA9 IC0SDA/PA8 RX1/PB TX1/PB5 RTS1/PB6 CTS1/PB LDO 16 VDD VSS NUC1SREAN NUC_RST# AVDD R8 10K R060 ICE_RST C7 10uF/10V TANT-A PA/ADC PA/ADC PA/ADC PA1/ADC1 PA0/ADC0 AVSS ICE_CK ICE_DAT PA1/PWM PA1/PWM1 8 PA1/PWM 7 PA15/PWM 6 PC8/SS10 5 PC9/SPCLK1 PC10/SDI10 PC11/SDO10 ICE_CLK ICE_DAT TICERST TICECLK 1M_O 1M_I TICEDAT TICECLK TICERST R9 0 1K R060 R060 R060 TICEDAT TICECLK TICERST RTCK1 100K R060 ADAVSS RTDA TICEDAT RTDA C060 X 1MHz XTAL-1 C9 0p RTDA1 100K R060 SSA RB060L C8 0p C060 JP HEADER 5X RRSET1 100K R060 TICERST AVDD USBVBUS L5 L060 C10 1u C060 CB 0.1u C060 R11 R060 R1 R060 USBVBUS DM DP J mini USB 5pin 1 6 VCC SHIELD 7 DM SHIELD 8 DP SHIELD 9 5 NC SHIELD GND USB_MINI_B L HEADER 5 JP ICE_DAT ICE_CLK ICE_RST RTIDA1 100K R060 DEBUG RICK1 100K R060 L6 L060 L0805 ADAVSS VCC GND USBVBUS DM DP JP11 1 HEADER UP6 RT916A-.v P5V USBVBUS PD SSA 1 JPR HEADER PV Title Nuvoton NU_TINY_1 RB060L CP1 10uF/10V TANT-B Size Document Number Rev A 1.0 Date: Monday, July 0, 01 Sheet of Aug. 0, 01 1 Revision V1.0

13 6 Downloading NuMicro Related Files from Nuvoton Website 6.1 Downloading NuMicro Keil μvision IDE Driver Step1 Visit the Nuvoton NuMicro website: Step Click here to enter Device Driver and Software Library. Aug. 0, 01 1 Revision V1.0

14 Step Click here to download the file. Step Download the NuMicro Keil μvision IDE driver. Aug. 0, 01 1 Revision V1.0

15 6. Downloading NuMicro IAR EWARM Driver Step1 Visit the Nuvoton NuMicro website: Step Click here to enter Device Driver and Software Library. Aug. 0, Revision V1.0

16 Step Click here to download the file. Step Download the NuMicro IAR Embedded Workbench driver. Aug. 0, Revision V1.0

17 6. Downloading NuMicro NUC1 Series BSP Software Library Step1 Visit the Nuvoton NuMicro website: Step Click here to enter Device Driver and Software Library. Aug. 0, Revision V1.0

18 Click here to download the file. Step Step Download the NuMicro NUC1 series software library. Aug. 0, Revision V1.0

19 7 Revision History Revision Date Description 1.0 Aug. 16, 01 Preliminary version Important Notice Nuvoton products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for other applications intended to support or sustain life. Further more, Nuvoton products are not intended for applications wherein failure of Nuvoton products could result or lead to a situation wherein personal injury, death or severe property or environmental damage could occur. Nuvoton customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Nuvoton for any damages resulting from such improper use or sales. Please note that all data and specifications are subject to change without notice. All the trademarks of products and companies mentioned in this datasheet belong to their respective owners. Aug. 0, Revision V1.0