Vipros 357 Queen with Fanuc 18P Control

Transcription

1 Vipros 357 Queen with Fanuc 18P Control Layout Drawings Amada America Inc Firestone Blvd. Buena Park CA Phone: (714) Fax: (714) Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 1 of 10

2 Warning Qualified personnel must complete all work. Do not apply power to the Vipros 357 Queen until an A.E.S.I. (Amada Engineering and Service Incorporated) Engineer is present and has instructed you to do so. Not all information required for proper installation, of the Vipros 357 Queen is included with this document. Specific details for proper installation are found in the document Vipros 357 Queen with Fanuc 18P User Pre-installation Guide available at the Amada America Internet web site at Considerable effort has been made to ensure that this manual is free of inaccuracies and omissions. However, as we are constantly improving our product, some of the data contained herein may be out of date. Please check our Internet site, for the latest release of this document. Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 2 of 10

3 Table Of Contents Planning the Location of the Machine...4 Plan View Vipros 357 Queen...5 Plan View Vipros 357 Queen with V357hs Conveyor...6 Plan View Vipros 357 Queen with V357hs Conveyor and MP1225 Loader...7 End View - Vipros 357 Queen...8 Elevation View Vipros 357 Queen...9 SBC EX 5.5Chiller Placement...10 Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 3 of 10

4 Planning the Location of the Machine The following diagrams provide the details for positioning your new machine.! Not all information required for proper installation, of the Vipros 357 Queen is included with this document. Specific details for proper installation are found in the document Vipros 357 Queen with Fanuc 18P User Pre-installation Guide available at the Amada America Internet web site at No obstacles are allowed in the worksheet travel area and the ceiling must be at least 40" above the top of the Vipros 357 Queen.! All of the Recommended Safety / Maintenance areas should be used, but you must at least ensure that the doors of the Fanuc 18P control unit can be opened. Any reduction of the Recommended Safety / Maintenance areas may increase the possibility of personnel injury and increase the time and cost of installation or maintenance.! The Vipros 357 Queen and Fanuc 18P control must be protected from direct sunlight or other heat sources. Exposure to direct heating sources such as infrared heaters have been shown to affect punch and die alignment.! The positioning of the SBC EX 5.5 Chiller is very flexible. Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 4 of 10

5 Plan View Vipros 357 Queen Electrical Requirements E1 Vipros 357 Queen 230 / 460 / 3 / 60 ±10% 30 kva / 3 / 60 VAC / 3 / 60 VAC E2 SBC EX5.5 Chiller 230 or 460 / 3 / 60 ±10% 15 kva / 3 / 60 VAC / 3 / 60 VAC Compressed Air Requirements P1 Vipros 357 Queen ft³/min " Recommended Safety / Maintenance Area 40" from all components 59.37" Maximum 183.8" Machine Length 37" 57" SBC 5.5 Chiller E2 26" 55" Hydraulic Unit 14" 10" 30" 28" E1 Fanuc 18P Control 59" VIPROS 357 QUEEN P1 Machine Centerline 100" Maximum Travel Area 50" Material 50" Working Range 72.0" to Load Position 74.41" to Edge of Table " Machine Width 288.0" Maximum Material Travel Area 144" Material 368" Recomended Safety / Maintenance Area 40" from all components Scale Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 5 of 10

6 Plan View Vipros 357 Queen with V357hs Conveyor Electrical Requirements E1 Vipros 357 Queen 230 / 460 / 3 / 60 ±10% 30 kva / 3 / 60 VAC / 3 / 60 VAC E2 SBC EX5.5 Chiller 230 or 460 / 3 / 60 ±10% 15 kva / 3 / 60 VAC / 3 / 60 VAC E3 V357hs Conveyor / 460 / 3 / 60 ±10%.8 kva / 3 / 60 VAC / 3 / 60 VAC / 3 / 60 VAC 59.37" Maximum 37" 57" SBC 5.5 Chiller E2 55" Hydraulic Unit 26" 14" 10" 30" 28" E1 Fanuc 18P Control 59" Compressed Air Requirements P1 Vipros 357 Queen ft³/min. 389" Recommended Safety / Maintenance Area 40" from all components 183.8" Machine Length 100" Maximum Travel Area 50" Material 50" Working Range P1 VIPROS 357 QUEEN Machine Centerline E3 V357hs Conveyor 66" 39" Access Required this area for scrap removal 72.0" to Load Position 74.41" to Edge of Table " Machine Width 288.0" Maximum Material Travel Area 144" Material 368" Recomended Safety / Maintenance Area 40" from all components Scale Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 6 of 10

7 Plan View Vipros 357 Queen with V357hs Conveyor and MP1225 Loader Electrical Requirements E1 Vipros 357 Queen 230 / 460 / 3 / 60 ±10% 30 kva / 3 / 60 VAC / 3 / 60 VAC E2 SBC EX5.5 Chiller 230 or 460 / 3 / 60 ±10% 15 kva / 3 / 60 VAC / 3 / 60 VAC E3 V357hs Conveyor / 460 / 3 / 60 ±10%.8 kva / 3 / 60 VAC / 3 / 60 VAC / 3 / 60 VAC 59.37" Maximum 37" 57" SBC 5.5 Chiller E2 55" Hydraulic Unit 26" 14" 10" 30" 28" E1 Fanuc 18P Control 59" P2 MP1225 Xformer E4 E4 MP1225 Loader 200 / 3 / 60 ±10%, 10 Kva To operate at 230 / 460 VAC a step up transformer with the following service is required / 3 / 60 VAC / 3 / 60 VAC / 3 / 60 VAC Compressed Air Requirements P1 Vipros 357 Queen ft³/min. P2 MP1225 Loader ft³/min. 389" Recommended Safety / Maintenance Area 40" from all components 183.8" Machine Length 100" Maximum Travel Area 50" Material 50" Working Range P1 VIPROS 357 QUEEN MP1225 Loader 65.95" " MP1225 Length Machine Centerline Forklift Access Required This Area For Material / Parts Loading / Unloading E3 V357hs Conveyor 66" 39" Access Required this area for scrap removal " Machine Width 72.0" to Load Position 74.41" to Edge of Table 75.41" to Edge of MP " Maximum Material Travel Area 144" Material 441" Recommended Safety / Maintenance Area 40" from all components " MP1225 Loader Width " Scale Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 7 of 10

8 End View - Vipros 357 Queen 22.8" Scale 7.9" 3.9" 19.7" 29.5" 35.4" 98.7" 110.6" Shipping Width w/o Crate 148.8" Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 8 of 10

9 Elevation View Vipros 357 Queen Center of Track " 52.2" Throat Depth 15.9" 50.0" 25.8" Y-axis 0" Reference 1.8" 19.7" 10.0" Scale Material Pass Line QUEEN 90.9" 28" Fanuc Control Hydraulic Unit 37.7"* 7.9" 8.7" 52.0" 63.0" 3.9" 33.5" 32.9" 9.8" 6.5" 11.0" 103.1" 184" 29.1" 13.8" 33.5" 14" 26" 9.9" 59.37" Maximum *Material Pass Line will vary with installed options Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 9 of 10

10 SBC EX 5.5Chiller Placement The SBC EX 5.5 Chiller is very important to the reliable operation of the Vipros 357 Queen. The SBC EX 5.5 Chiller must be placed so that an adequate flow of air is maintained. The position of the SBC EX 5.5 Chiller is flexible. The SBC EX 5.5 Chiller is supplied with two (2) fifteen-foot lengths of hose to connect the to the Vipros 357 Queen Hydraulic Unit. The customer may supply a longer length of hose if required. Under normal operating conditions the SBC EX 5.5 Chiller may be placed against walls as shown. However, for maintenance purposes access to all sides of the SBC EX 5.5 Chiller may be required. The SBC EX 5.5 Chiller must have a minimum 60" of clearance above the SBC EX 5.5 Chiller for proper airflow. Under normal operation the chiller may be placed against walls as shown. For maintenance access to all sides may be required. Chiller Location is shown for reference only. Maximum Material Travel Area X144" by Y50" Fanuc 18P Control Hydraulic Unit 6" 2 supplied 15ft. water hoses 6" Air Flow Print Date 01/25/2001 Revision 4.0 This document available on the World Wide Web at Page 10 of 10