instructions for assembly Hard Drive & Hard Drive Doubler Parts list 2* hard drive doubler 12* 6-32 UNC panhead 1 x body 4* 6-32 hex standoff

Transcription

1 Cubit 5 instructions for assembly Bag 3 Hard Drive & Hard Drive Doubler Parts list 2* hard drive doubler 12* 6-32 UNC panhead 1 x body 4* 6-32 hex standoff 1 x front plate 1 x back plate 1 x top tray 1 x bottom tray with card reader & cable 1 x PSU strap 1 x IR remote plate for optional Microsoft Infra-Red Remote dongle 9 x fixing bags - please note that appearance (eg metal type, body thickness of standoffs) may vary from pictures: Bag 1 Motherboard & Front Port Board 2* M3 lock washer 4* M3 x 6 panhead 5* M3 x 8 panhead 4* 6-32 hex standoff 2* M3 hex standoff Bag 4 DVD slim IDE adaptor (with screws) CD eject button 1* sticky 4* M2 x 4 panhead Bag 2 PSU Athlon PSU plate 2* M3 x 8 panhead 2* M3 x 5 socket buttonhead 2* 6-32 thumbscrew 2* fan screw 2* rubber washer Bag 5 Wireless Module 1* single internal USB cable 400mm approx 2* M2 x 4 panhead 2* M3 x 6 panhead

2 Bag 6 IR Remote Bag 8 - Front plate 1* 5-way internal USB cable 1* M2 6mm nylon spacer 1* M2 x 12 panhead 2* M3 x 8 panhead 2* M3 x 16 socket 4* M3 x 10 socket buttonhead 4* black fibre washer 2* M3 nut 2* M3 hex spacer 1* Switch Assembly 1* Infra-Red filter 1* Power button 1* Reset button Bag 7 Back plate PCI clip blanking plate clip 2* M3 x 8 socket buttonhead 4* M3 x 5 socket buttonhead 4* M3 thumbscrew 4* 6-32 thumbscrew 1* rubber grommet 8* rubber washer Bag 9 - Spares & Allen Key

3 Build instructions 1. Front port board Add 6-32 hex standoffs for attaching CPU heatsink. (Some Shuttle models do not require these as an Intel retainer clip is provided for the heatsink.) Mount to bottom tray using M3 panhead Add card-reader cable: 2. Mainboard Please check your Shuttle mainboard to see which of the following applies (use 1 lock washer with each standoff): Mount mainboard using M3 x 8 panhead (M3 x 6 for front corner on standoff). NB if using Athlon 64, CPU & heatsink should be mounted to mainboard BEFORE mounting to tray. 3. Positioning of 2.5 drive if used (fixings not provided for this but standard M3 x 5mm may be used) type 1 type 2

4 4. Power Supply Unit Bend around PSU and secure using M3 x 8 panhead. Insert tab on top tray into slot on PSU. Then screw in 1* M3 x 8 panhead to stop PSU from sliding forwards. 5. Hard Drive(s) Bend end of PSU strap and insert into top tray: Screw 4 x 6-32 hex standoff into hard drive: Add 2 nd hard drive (if used) using doublers and 8 x 6-32 UNC screw:

5 Attach hard drive(s) to underside of top tray using 4 x 6-32 UNC screws: 7. Optional Shuttle PN11/PN15 Wireless LAN Module Mount module to back of top tray with 2* M2 x 4 panhead. Mount USB header mini-pcb to front of top tray using 2* M3 x 6 panhead: 6. Optical drive (CD/DVD) Attach Slim IDE Adaptor with screws provided: Attach USB cable (from PN11) from module to mini-pcb. Attach Single USB cable 400mm to mini-pci and direct down through gap in top tray: Attach drive to top tray using 4* M2 x 4 panhead: Attach other end of Single USB cable 400mm to internal USB header on mainboard (exact location may vary according to Shuttle board used). NB When connecting any 4-pin USB cable please note that the live (red) wire should always go furthest away from the key (missing) pin on the header:

6 8. Optional Microsoft Media Center Infra-Red Receiver Please note use of nylon spacer with M2 x 12 screw: Dismantle casing of MS IR dongle: Please note cabling details (exact position of header on mainboardmay vary according to Shuttle board used example is SB83):: Mount PCB to the mounting plate using fixings provided: Please note positioning of mounting plate (see also next section on sliding trays into case):

7 Thread Infra-Red/Sky signal receiver cable through rubber grommet (see fixings Bag 7), and insert grommet into back plate (only one SPDIF cable may be used simultaneously with MS Media Centre Infra-Red): Detail lift top of PSU strap when sliding trays in this will prevent the strap scraping the side of the case. 9. Sliding trays into case After connecting up any cables (IDE, ATX etc), carefully place top tray over bottom tray and slide gently into case. Please take care with the PSU strap consult photos below: NB You may slide the trays in either way (back first or front first). Pictures above show back sliding in first. 10.Back Plate Attach blanking plates (if used) using blanking plate clip and M3 x 5mm socket buttonhead screw and allen key: Attach SPDIF cable(s) if used using M3 x 8mm socket buttonhead (apply a little force to engage screw):

8 Attach wireless module aerial (if used): Attach backplate to Shuttle fan module using 4 x 6-32 thumbscrew. Use outer holes for 90mm fans (as in pic), inner holes for 80mm fans. Attach Shuttle backplane using M3 x 5mm socket buttonhead screws: Attach backplate to body of case using 4 x M3 thumbscrew: Attach expansion cards/blanking plates using PCI-clip and M3 x 5mm socket buttonhead screw: Attach Athlon PSU plate (if needed required by some Shuttle Athlon models which have a smaller PSU) using 2* M3 x 5mm socket buttonhead screw: Place backplate on case. Attach backplate to PSU using either 2 x fanscrew or 2 x 6-32 thumbscrew (depending on Shuttle PSU being used). 11.Front Plate Mount switch assembly using 2* M3 x 16mm socket screws, 2 x M3 hex spacer and 2 x M3 nut (see also next page):

9 Insert eject button (see fixings Bag 4 filter into front plate: DVD) and Infra-Red Attach switch to mainboard. Attach frontplate to body of case using 4* M3 x 10 socket buttonhead screws and 4 x M3 fibre washers: YOUR CUBIT IS READY!