PAR EverServ ES500 Installation and Configuration Guide

Transcription

1 PAR EverServ ES500 Installation and Configuration Guide Revision History 0 - Revision 2 - MSR Configuration Functionality Added 04/10/ Revision 1 - Pixel32 INI line fixed 12/03/ Revision 0 - Initial Release

2 Publication Details Copyright Copyright ParTech, Inc All Rights Reserved. This product and related documentation are protected by copyright and are distributed under licenses restricting their use, copying, distribution, and decompilation. No part of this product or related documentation may be reproduced in any form by any means without prior written authorization of PAR and any requisite licensors. Trademarks PixelPoint, ParTech, and their respective logos are all trademarks of PAR Technology Corporation. PAR may have patents, patent applications, trademarks, copyrights, or other intellectual property rights covering subject matter in this document. Except as expressly provided in any written license agreement from PAR, the furnishing of this document does not give you any license to these patents, trademarks, copyrights, or other intellectual property. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Other product names may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Disclaimer PAR has thoroughly reviewed this document and believes it to be reliable. However, this document is provided for informational purposes only and PAR makes no warranties, either expressed or implied, in this document. Information in this document is subject to change without notice. Risk of use and responsibility for the results of use of this document lie with the user. Patents The following patents apply to some areas of functionality within the PixelPoint software suite: Pat. 6,384,850; 6,871,325; 6,982,733; 8,146,077; 8,287,340

3 Table of Contents ES500 Installation and Configuration Guide Overview... 4 System... Files 5 PixelPoint... OPOS Files 6 PAR... OPOS Drivers 7 Modifying... Pixel32.ini 8 Cash... Drawer Registry Configuration 9 Magnetic... Swipe (MSR) Configuration 10

4 Overview This document is intended for those who are setting up PAR s EverServ 500 terminal to run PixelPoint Pos. You should know how to install and configure PixelPoint POS prior to reading this document. Refer to the PixelPoint POS Installation Guide for more information. The following chapters describe installation and configuration steps that may be needed to set up Cash Drawer, Customer Display and MSR peripherals. In most cases, terminals ordered and shipped through PAR will arrive ready to go, in which case this document can be used as a reference guide. This document also contains information that can be referenced in cases where the Operating system has been replaced or configuration changes have been made in error. This document contains the following sections: System Files PixelPoint OPOS Files PAR OPOS Drivers Modifying Pixel32.ini Cash Drawer Windows Registry Configuration Magnetic Swipe (MSR) Configuration Page 4 Copyright ParTech, Inc All Rights Reserved.

5 System Files Begin the setup operation by obtaining the necessary system files. Open the "EverServ500" ZIP file containing these files. Extract the four ZIP files within: CCO.zip VFD.zip Cash Drawer.zip PixelPoint OPOS.zip Perform the following steps. For each step, make sure to run the executable as *Administrator*. You will only be running the contents of three of the ZIP files in this section. 1. Run OPOS COO v1.6 Runtime.exe from the CCO.zip archive. 2. Run Setup.exe from the VFD.zip archive. 3. Run Setup.exe from the Cash Drawer.zip archive. Page 5 Copyright ParTech, Inc All Rights Reserved.

6 PixelPoint OPOS Files If the Windows path on your system differs from the one shown in these instructions, modify the paths in these instructions accordingly. Extract the files from PixelPoint OPOS.zip, and then perform the following steps: 1. Copy DrawerOPOSes500.dll and PoleShowOPOS.dll to the \PixelPOS\DLLS directory. Create this folder if it does not already exist. 2. Copy the following files into C:\Windows\System32: Cocash.ocx Codisp.ocx Opos20.dll 3. Open Windows Start Menu and type "cmd". Right-click on cmd (the icon), and select Run as administrator. Agree to the UAC notification if it appears. 4. Type "regsvr32 C:\Windows\system32\Codisp.ocx" in the command line, and then press Enter. This will register Codisp.ocx in the Windows Registry. You should get the following message: Repeat steps 3 to 4 for Cocash.ocx. They must be registered individually. After both OCX files have been registered, proceed to the next section. Page 6 Copyright ParTech, Inc All Rights Reserved.

7 PAR OPOS Drivers OPOS drivers should already be installed on the terminal when it ships from PAR. Look for them in the Windows Start Menu under "OPOS Utility". Run the utilities to ensure the OPOS devices are operating. If the OPOS Utility drivers are not installed, look for the installation file Setup.exe in the C:\PAR Drivers\ES500_OPOS_V101\ES500\V1.0.1\ directory. Make sure to run it as Administrator by right clicking on the file and choosing "Run as Administrator". Now open Windows Registry Editor by running "regedit" from the Windows Start Menu. Navigate to the following key to verify that the device names on the system are the same as in the image below: HKEY_LOCAL_MACHINE\SOFTWARE\OLDforRetail\ServicesOPOS Once the OPOS installation has been verified, continue to the next section in this document. Page 7 Copyright ParTech, Inc All Rights Reserved.

8 Modifying Pixel32.ini Edit \PixelPOS\pixel32.ini and add a section for each terminal. For example, if you have six stations, you would need to have six station sections in the INI file. Make sure that each station section for an EverServ 500 terminal has the following lines under its heading. Station 1 is shown below. [STATION1] PoleDeviceName=FTLDSO PoleDisp=DLLS/PoleShowOPOS.dll Drawer1=FTCD1 Drawer=DLLS/DrawerOPOSes500.dll DrawerOpenTimeOut=10 LeaveOnDrawerClose=Y Page 8 Copyright ParTech, Inc All Rights Reserved.

9 Cash Drawer Registry Configuration In order for the cash drawer to be properly configured, a particular key in the Windows Registry must have a particular value. It is set as follows: 1. Open the Windows Registry Editor. 2. Navigate through the keys (folders) on the left to the following path: \HKEY_LOCAL_MACHINE\SOFTWARE OLEforRetail\ServiceOPOS\CashDrawer\FTCD1 3. Double-click on InputStatus in the right panel, and edit the Value data field appropriately: If the cash drawer is made by PARTech, this should be "0". If the cash drawer is not made by PARTech, this should be "1". Page 9 Copyright ParTech, Inc All Rights Reserved.

10 Magnetic Swipe (MSR) Configuration Run the MagSwipe Configuration Utility and configure it as follows: 1. Press [Select Reader Interface] on the left 2. Select the image of the USB cable. 3. Select [Continue]. 4. Press [Change Basic Reader Settings] on the left 5. Switch to the Track Setting tab. 6. Select Track1 Or Track 2 from the 'Track Select' section. 7. Change the 'Track Separator' field to "\null". You can use the Non-Printable Char dropdown box to the right to do this. 8. Select [Send to MSR]. Page 10 Copyright ParTech, Inc All Rights Reserved.

11 When you are finished, the following message will appear. At this point, your MSR has been configured and you can exit out of the MSR Configuration Utility. Page 11 Copyright ParTech, Inc All Rights Reserved.