DriveManager 5. Installation Manual. Engineering tool

Transcription

1 DriveManager 5 Installation Manual Engineering tool Configuration, commissioning, service and diagnostics for drive controller families ServoOne, ServoA, ServoC, cline

2 2 DriveManager 5 This installation manual describes the installation of the PC software DriveManager 5. The commissioning of the drive controllers and their software functions are described in the device help for the related device series. DriveManager 5 supports you during y Configuration y Commissioning y Service y Diagnostics y Project management of the drive controller families ServoOne, ServoA, ServoC and cline. ID no.: B.4-00 Date: 11/2016 Valid from software version: The German version is the original of this documentation. Subject to technical change without notice. The content of our documentation was compiled with the greatest care and attention, and is based on the latest information available to us. We should nevertheless point out that this document cannot always be updated simultaneously with the on-going technical development of our products. Information and specifications may be subject to change at any time. Please obtain information on the latest version at

3 Table of contents 1 General Target group Reference documents Pictograms Disclaimer Technical Helpline Uninstalling Setup Control Panel Start menu Preparation Scope of supply Connection cable System requirements Operating system Additional software Installation InstallationShield Wizard DriveManager setup Installation completed Getting started and help Monitor configuration System help Program help Device help Table of contents 3

4 Table of contents 4

5 1 General 1.3 Pictograms The pictograms used in this installation manual signify the following for the user: 1.1 Target group Dear user, The documentation forms part of DriveManager 5 and contains important information on installation. It is aimed at all persons who install DriveManager 5 on desktop or notebook computers. 1. (digit) NOTE Useful information or reference to other documents. ACTION TO BE TAKEN Processing step undertaken by the user or the system. 1.2 Reference documents Documentation on DriveManager 5 Document Contents ID no. Format DriveManager 5 Installation Manual Description of the system requirements and installation B.x PDF DriveManager 5 Program Help Description of the functions and configuration options B.x PDF,.NET, html5 1.4 Disclaimer This documentation and DriveManager 5 are utilised exclusively as defined by the "Grüne Lieferbedingungen" (Green terms and conditions of delivery) issued by the ZVEI - Zentralverband Elektrotechnik- und Elektronikindustrie e.v., as well as the "Softwareklausel" (Software clause) issued by the ZVEI - Zentralverband Elektrotechnikund Elektronikindustrie e.v. These documents are available at Other documents Document Contents ID no. Format ServoOne Device Help Description of the basic software B..x ServoOne CM Device Help Description of the basic software B.x PDF,.NET, html5 PDF,.NET, html5 1 General 5

6 1 General Technical Helpline Our Technical Helpline will provide you with fast, specific assistance if you have any technical queries relating to the installation of DriveManager 5. Address: LTI Motion GmbH Gewerbestrasse Lahnau The Technical Helpline is available by or telephone: Service hours: Mo.-Fr.: 8 a.m. - 5 p.m. (CET) helpline@lti-motion.com Telephone: NOTE: You will find detailed information about our services on our web site in >Support Service.

7 2 Preparation 2.1 Scope of supply This installation manual supports you during the installation of DriveManager 5. Device types supported y cline y ServoOne single-axis system y ServoOne multi-axis system y ServoOne junior y ServoOne CM y ServoA y ServoC y ServoCplus Contents of CD-ROM / download file LTI DST-Kernel LTI DST-Kernel-Visu LTI IP Network Configuration LTi DriveManager LTI Commissioning Loader LTi USBIO Driver CP210x USB to UART Bridge Driver Installer Device Support Packages Dictionary (dialog text) "Chinese (Simplified, PRC)" Dictionary (device text) "Chinese (Simplified, PRC)" Kernel for LTI Drive Service Tools Function Kernel for data display for LTI Drive Service Tools Tools for setting IP address Commissioning, service and diagnostics program Loader for quick, straightforward serial commissioning of drives Optional USB device driver for Windows 7 and later USB/RS232 converter for device communication via simulated COM ports Package(s) with DST device drivers and data Dictionary for dialog text strings Dictionary for device text strings DriveManager 5 functions y Initial commissioning of single and multi-axis systems y Quick serial commissioning using commissioning file (firmware, parameters, iplc) y Operation, parameter configuration Table 2.1 Contents of the CD-ROM / the download file NOTE Connection cables are not included in the scope of supply and must be ordered separately. y Diagnostics (oscilloscope board) y Manual control of the drive y Project management 2 Preparation 7

8 2 Preparation Connection cable 2.3 System requirements Ethernet interface Crosslink-Ethernet cable "CC-ECL03", CAT 5 with 2 x RJ45 connectors Article number: USB interface USB connection cable "CC-USB03", type A to type B. Article number: Feature Minimum requirements Recommended Operating systems Microsoft Windows XP (SP2)*, Windows Vista (32/64 bits) Additional software Microsoft.NET Framework 4 Interfaces (please pay attention to notes) Processor A spare Ethernet interface or a spare USB interface (not necessary for all devices) 1.5 GHz Memory 1 GB RAM 2 GB RAM Hard disk Drive 2 GB spare hard disk space CD drive Windows 7 (32/64 bits), Windows 8 (32/64 bits), Windows 10 (32/64 bits) Monitor 1024 x 768 pixels at 96 dpi 1920 x 1080 pixels (FullHD) at 100 % text size * USB cannot be used for ServoOne with Windows XP! Table 2.2 System requirements

9 2.4 Operating system Make sure that your operating system is up-to-date and all service packs (for Windows XP service pack 2 as a minimum) and updates are installed. You can check as follows whether your operating system is up-to-date: Windows XP y Windows Start button y Click "All Programs" y Open Internet Explorer y "Tools" menu y Windows Update Windows 7 y >Start >Control Panel In the "Icons" view: >Windows Update In the "Category" view: >System and Security >Windows Update 2.5 Additional software You can check whether and which version of.net Framework is installed on your system as follows: Windows 7 y >Start >Control Panel Windows 10 In the "Icons" view: >Programs and Features >Search Programs and Features "Microsoft.NET Framework" In the "Category" view: >Programs >Programs and Features >Search Programs and Features "Microsoft.NET Framework" y.net Framework is an integral part of Windows from Windows 10. If version 4 (or later) of "Microsoft.NET Framework" is not installed on your computer, please download it from the Microsoft homepage and install it on your PC. Windows 10 y >Start >Settings >Updates and Security 2 Preparation 9

10 2 Preparation 10

11 3 Installation y Please accept the dialog box that appears by clicking the "Next >" button. y Right-click the file "setup.exe" and select "Run as administrator" on the pop-up menu. NOTE Please note that administrator rights are required. If necessary, contact your system administrator. 3.1 InstallationShield Wizard y In the following dialog box, "Choose Destination Location", you can change the installation path using the "Browse..." button. Please then accept the dialog box by clicking the "Next >" button. After "setup.exe" has started, an InstallationShield Wizard is installed first. NOTE The dialog boxes for the InstallationShield Wizard are always in English. 3 Installation 11

12 3 Installation 12 y In the following dialog box, "Ready to Install the Program", please start the installation of the InstallationShield Wizard by clicking the "Install" button. 3.2 DriveManager setup After the InstallationShield Wizard has been successfully installed, the Setup for the DriveManager software package appears automatically. y The successful installation of the InstallationShield Wizard is indicated with a final dialog box that you can close by clicking the "Finish" button.

13 y In the left part of the Setup with the white background, you can select the components to be installed. Components to be installed must always be marked with a check mark. Information on the individual components is displayed underneath the left part of the Setup with a white background if you move the mouse pointer over the individual components. y Click the "Install" button to start the installation of the components marked. With some versions of Windows you will receive a prompt for one of the drivers to be installed. y The components already installed are listed in the right part of the Setup with a colour background. During initial installation, no components are shown on the right side. y If the check box for the "Run installation in automatic mode" function is selected, all components to be installed are installed one after the other. Without this function each component must be installed separately. y You can cancel the installation by clicking the "Close" button, after a further confirmation prompt. 3 Installation 13

14 3 Installation 14 y You can interrupt aninstallation in progress by clicking the "Break installation" button. Setup then remains open and indicates the components still to be installed and already installed. You can continue the installation by clicking the "Install" button or cancel the installation by clicking the "Close" button and accepting a confirmation prompt. y You can display product and version information for Setup by clicking the "About..." button. The same applies for all components. 3.3 Installation completed After successful installation, Setup remains open and indicates which components have been installed and which components have not been installed.

15 Three icons also appear on the desktop: Icon Function DriveManager 5, the program for the configuration, commissioning, service, diagnostics and project management of drive controllers from LTI Motion. The usage of DriveManager 5 is described in detail in the system help (see also 4.2 System help on page 17). Separate loader for the serial commissioning of drive controllers. You can use this application to load commissioning files prepared in advance using DriveManager 5. Program for configuring the IP network without the need to start DriveManager 5. Table 3.3 Desktop icons 3 Installation 15

16 3 Installation 16

17 4 Getting started and help 4.1 Monitor configuration If the entire user interface for DriveManager 5 is not displayed, it may help to change the size of the text (recommendation: 100 %) or the monitor resolution. Windows 7 y Setting the size of the text >Start >Control Panel In the "Icons" view: >Display In the "Category" view: >Appearance and Personalization >Display y Setting the monitor resolution >Start >Control Panel Windows 10 In the "Icons" view: >Display >Adjust resolution In the "Category" view: >Appearance and Personalization >Display >Adjust resolution y >Start >System >Display 4.2 System help DriveManager 5 has context-sensitive system help. If you press the F1 key, help related to the element of the application with the focus (e.g. window, dialog box or data entry field) opens; the help describes this element. The system help is divided into the following different help systems: Program help The functions of DriveManager 5 are described in the "Program help" There is an overview of the user interface, the function of the oscilloscope and project management (menu bar >Help >Program Help) Device help The software functions for the device connected are described in the "Device help" (menu bar >Help >Device Help). 4 Getting started and help 17

18 4 Getting started and help 18

19 5 Uninstalling There are various methods of uninstalling DriveManager 5 or individual components. NOTE 5.1 Setup Please note that all methods require administrator rights. If necessary, contact your system administrator. NOTE The dialog boxes for the InstallationShield Wizard are always in English. You can start the InstallationShield wizard by clicking the "Start" button. The Setup for the DriveManager software package appears. The components installed are listed in the right part of the Setup with a colour background. You can now select individual components to uninstall. Components to be uninstalled must always be marked with a check mark. Click the "Uninstall" button to start the uninstallation of the components marked. With this method both individual components and the complete DriveManager 5 software package can be uninstalled. y Right-click the file "setup.exe" and select "Run as administrator" on the pop-up menu. y After you start "setup.exe", first an InstallationShield Wizard prompt appears with various options. Click the "Uninstall" button in the InstallationShield Wizard to start the uninstallation of all components installed. Click the "Uninstall starter only" button to uninstall only the InstallationShield Wizard. 5 Uninstalling 19

20 5 Uninstalling Control Panel This is the most time-consuming method as the components must all be uninstalled separately. Windows 7 y >Start >Control Panel In the "Icons" view: >Programs and Features In the "Category" view: >Programs >Programs and Features y One after the other, double-click the programs with names that start with "LTI" and with version information that starts with "5.6". Answer the subsequent conformation prompt with "Yes". 5.3 Start menu If you use this method it is not possible to select individual components. It is only possible to uninstall the DriveManager 5 software package. y >Start >All Programs >LTI Motion GmbH >DST >5.6 >LTI Uninstaller for DST Package y All components installed are uninstalled without any further prompt. NOTE Using this method, all components that were installed using Setup are uninstalled. Components installed by another method and components for older DriveManager versions are retained.

21 Glossary Symbole.NET... 5, 8, 9 A Address IP... 7, 15 LTI Motion GmbH Administrator rights... 11, 19 C Cable. see Connection cable cline... 7 Commissioning Loader... 7, 15 Connection cable... 7, 8 Copyright D Date of this document... 2 Desktop icons Device types supported... 7 Disclaimer... 5 Driver... 7, 13 E Ethernet... 8 H Help Device Program... 5, 17 System... 15, 17 Helpline. see Technical Helpline I Icons. see Desktop icons Installation... 2, 5, 6, 7, 11, 12, 13, 14 Wizard... 11, 12, 19 Interface... 8 IP Network Configuration... 7, 15 L Loader for the serial commissioning. see Commissioning Loader M Memory... 8 Monitor configuration N Network O Operating system... 8, 9 Original language of this document... 2 P Pictograms... 5 Processor Glossary 21

22 6 Glossary 22 R RAM. see Memory Resolution. see Monitor configuration S Scope of supply... 7 Serial commissioning. Siehe Commissioning Loader Service. see Technical Helpline ServoA... 7 ServoC... 7 ServoCplus... 7 ServoOne... 7, 8 Setup... 12, 14, 19, 20 Software clause. see Disclaimer Support. see Technical Helpline System requirements... 8 T Technical Helpline... 6 Terms and conditions of delivery. see Disclaimer Text size. see Monitor configuration U USB... 8 V Version Of software components Of the DriveManager version described... 2 Of this document... 2

23 23

24 LTI Motion GmbH Gewerbestrasse Lahnau Germany Phone +49(0) Fax +49(0) Copyright All content of the documentation, in particular the text, photographs and graphics it contains are protected by copyright. The copyright lies, unless otherwise expressly stated, with LTI Motion GmbH.