Shielded Power Inductors High Inductance
|
|
|
- Buddy Carroll
- 6 years ago
- Views:
Transcription
1 Document Shielded Power Inductors High Inductance High inductance values (22 47 µh) not available in the corresponding LPS series of parts Rugged construction improves pick and place operation Core material Ferrite Core and winding loss See Environmental RoHS compliant, halogen free Terminations RoHS compliant matte tin over nickel over silver. Ambient temperature C to +85 C with current, +85 C to +1 with derated current Storage temperature Component: C to +1. Tape and reel packaging: C to +8 C Resistance to soldering heat Max three second reflows at +26 C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at < C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 PCB washing Tested with pure water or alcohol only. For other solvents, see Doc787_PCB_Washing.pdf. Inductance 2 DCR max 3 SRF typ 4 (A) 5 (A) 6 Part number 1 ±2% (µh) (Ohms) (MHz) % drop 2% drop % drop 2 C rise C rise LPZ8-224MR_ LPZ8-334MR_ LPZ-334MR_ LPZ15-334MR_ LPZ3314-5MR_ LPZ MR_ LPZ12-335MR_ LPZ18-155MR_ LPZ18-185MR_ LPZ18-225MR_ LPZ18-335MR_ LPZ MR_ LPZ MR_ LPZ MR_ LPZ MR_ LPZ5-5MR_ LPZ MR_ LPZ MR_ When ordering, please specify termination and packaging codes: LPZ8-334MRC Termination: R = RoHS compliant matte tin over nickel over silver. Special order, added cost: Q = RoHS tin-silver-copper (95.5/4/.5) or P = non-rohs tin-lead (63/37). Packaging: C = 7 machine-ready reel. EIA-481 embossed plastic tape). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13 machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked 2. Inductance tested at khz,.1 Vrms using an Agilent/HP 4192A. 3. DCR measured on a micro-oheter. 4. SRF measured using an Agilent/HP 8753ES or equivalent. 5. DC current that causes the specified inductance drop from its value without current. 6. Current that causes the specified temperature rise from ambient. 7. Electrical specifications at. Refer to Doc 362 Soldering Surface Mount Components before soldering. Document Revised 1/5/15
2 Document Shielded Power Inductors LPZ8 L vs Current L vs Frequency Inductance (µh) µh 22 µh Inductance (µh) µh 22 µh Current (A) Frequency (MHz) Percent of rated Current Weight mg Packaging /7 reel; 35/13 reel Plastic tape: 12 wide,.23 thick, 8 pocket spacing, 1.37 pocket depth Recoended pick and place nozzle OD: 3 ; ID: 1.5 Document Revised 1/5/15
3 Document Shielded Power Inductors LPZ L vs Current Inductance (µh) µh L vs Frequency Inductance (µh) µh Current (A) Frequency (MHz) Typical Percent of rated Current Weight mg Packaging /7 reel; 35/13 reel; Plastic tape: 12 wide,.23 thick, 8 pocket spacing, 1.4 pocket depth Recoended pick and place nozzle OD: 3 ; ID: 1.5 Document Revised 1/5/15
4 Document Shielded Power Inductor LPZ15 L vs Current Inductance (µh) µh L vs Frequency Current (A) Weight 45 mg Packaging /7 reel; 35/13 reel; Plastic tape: 12 wide,.26 thick, 8 pocket spacing, 1.65 pocket depth Recoended pick and place nozzle OD: 3 ; ID: 1.5 Document Revised 1/5/15
5 Document Shielded Power Inductors LPZ Weight mg Packaging /7 reel; 35/13 reel Plastic tape: 12 wide,.3 thick, 8 pocket spacing, 1.52 pocket depth Recoended pick and place nozzle OD: 3.3 ; ID: 1.65 Document Revised 1/5/15
6 Document Shielded Power Inductors LPZ ±.3 3,9 ±, XXX X Dash number Internal code.1535 ±.3 3,9 ±, ±.4 1, ±,.1 2, ,15 Winding direction Recoended Land Pattern.5 2, ,5.5, ,89.6 1,52 Dimensions are of the case not including the termination. For maximum overall dimensions including the termination, add.5 in /,13. For optional tin-lead and tin-silver-copper terminations, dimensions are for the mounted part. Dimensions before mounting can be an additional.5 inch /,13 ) , , Weight mg Packaging /7 reel; 35/13 reel Plastic tape: 12 wide,.25 thick, 8 pocket spacing, 1.32 pocket depth Recoended pick and place nozzle OD: 4 ; ID: 2 Document Revised 1/5/15
7 Document Shielded Power Inductors LPZ Weight 9 mg Packaging /7 reel; 35/13 reel Plastic tape: 12 wide,.23 thick, 8 pocket spacing, 1.9 pocket depth Recoended pick and place nozzle OD: 4 ; ID: 2 Document Revised 1/5/15
8 Document Shielded Power Inductors LPZ ±.4 4, ±, XXX X Dash number.59 1,5 Internal code.169 ±.4 4, ±,.551 1, max. typ, , , Winding direction Recoended Land Pattern.128 3, , ,.,75 typ Dimensions are of the case not including the termination. For maximum overall dimensions including the termination, add.5 in /,13. For optional tin-lead and tin-silver-copper terminations, dimensions are for the mounted part. Dimensions before mounting can be an additional.5 inch /,13 )..59 1, ,.185 4,7 Weight mg Packaging /7 reel; 35/13 reel Plastic tape: 12 wide,.3 thick, 8 pocket spacing, 1.52 pocket depth Recoended pick and place nozzle: OD: 4.5 ; ID: 2 Document Revised 1/5/15
9 Document Shielded Power Inductor LPZ Weight 7 75 mg Packaging /7 reel; 35/13 reel Plastic tape: 12 wide,.3 thick, 8 pocket spacing, 1.2 pocket depth Recoended pick and place nozzle OD: 5 ; ID: 2.5 Document Revised 1/5/15
10 Document Shielded Power Inductors LPZ515 Typical Dimensions are in inches Weight 2 7 mg Packaging /7 reel; 35/13 reel Plastic tape: 12 wide,.3 thick, 8 pocket spacing, 1.57 pocket depth Recoended pick and place nozzle OD: 5 ; ID: 2.5 Document Revised 1/5/15
Wirewound Chip Inductors
FEATURES CERAMIC BODY, WIRE WOUND CHIP INDUCTOR SIZES K (0402) HIGH CURRENT AND LOW DCR *See Part Number System for Details REFLOW SOLDERING APPLICABLE TAPE & REEL PACKAGING FOR AUTOMATIC PICK-PLACE Specifications
SRR1210A Series - Shielded Power Inductors
*RoHS COMPLIANT & AEC-Q QUALIFIED Features Shielded construction Inductance range: to μh Heating current up to 11 A Dimensions: 12 x 12 x 10 mm AEC-Q qualified RoHS compliant* and halogen free** SRR1210A
Air Core RF Inductors
GENERAL DESCRIPTION AVX Air Core RF Inductors, part of the wound air core inductor family, are ideal for RF circuits, broadband I/O filtering, frequency selection, or impedance matching. The air core inductor
SSL0618 Series. SMD Power Inductors. Description
YAGEO CORPORATION SMD INDUCTOR / BEADS SMD Power Inductors SSL0618 Series For SSL series provide excellent current carrying capabilities in a small footprint. They have a flat top for reliable pick and
DCR. Irms (A) Isat (A) Max.
*RoHS & AEC COMPLIANT 1R 5 Features Shielded construction Carbonyl powder core High saturation current Inductance range:.1 to 33 µh AEC-Q2 compliant RoHS compliant* and halogen free** SRP728A Series -
I rms (A) Typ. DCR (mω) Typ. DCR (mω) Max. 0.7 ± 0.2 (.028 ±.008)
*RoHS COMPLIANT, **HALOGEN FREE & AEC-Q COMPLIANT Features Shielded construction Metal alloy powder core High saturation current Inductance range.15 to 1 µh AEC-Q compliant RoHS compliant* and halogen
YAGEO CORPORATION SMD INDUCTOR / BEADS. Power supply, power amplifiers Switching regulators. Features
YAGEO CORPORATION SMD INDUCTOR / BEADS SMD Power Inductors STD0804 Series Yageo SMD power inductors are best designed for noise / EMI / RFI filters for surface mounting applications. These components contain
CR0603/CR0805/CR Chip Resistors
*RoHS COMPLIANT Features RoHS compliant* Power rating at 70 C: CR0603-0.10 W, CR0805-0.125 W, CR1206-0.25 W Tight tolerances of bottom electrode width Suitable for all types of soldering processes Three
PAA140STR. Dual Single-Pole, Normally Open OptoMOS Relays INTEGRATED CIRCUITS DIVISION
Dual Single-Pole, Normally Open OptoMOS Relays Parameter Rating Units Load Voltage 4 V Load Current ma rms / ma DC On-Resistance (max 8 Features 37V rms Input/Output Isolation Low Drive Power Requirements
Specification Status: Released
PAGE NO.: 1 of 9 Specification Status: Released BENEFITS ESD protection for high frequency applications (HDMI 1.3) Smaller form factor for board space savings Helps protect electronic circuits against
ML100SRI. Series. Ultra-Miniature, 1W High Isolation, SMT DC/DC Con vert ers. Key Features:
ML100SRI Ultra-Miniature, 1W High Isolation, SMT DC/DC Con vert ers Key Features: 1W Output Power Ultra-Miniature SMT Case 4,200 VDC Isolation Single & Dual Outputs -40ºC to +105ºC Operation Meets JEDEC
SMD Power Inductors CATALOGUE.
SMD Power Inductors CATALOGUE www.lairdtech.com 1 ABOUT LAIRD TECHNOLOGIES Laird Technologies designs and manufactures customized, performancecritical products for wireless and other advanced electronics
INPAQ. Specification. MCB0603 Series. Product Name Chip Ferrite Bead Series MCB 0603 Size EIAJ Global RF/Component Solutions
MCB0603 Series Specification Product Name Chip Ferrite Bead Series MCB 0603 Size EIAJ 0603 Chip Ferrite Bead (MCB0603 Series) Engineering Spec. 1.Features Monolithic inorganic material construction. Closed
INPAQ. Specification. MCB0603 Series. Product Name Chip Ferrite Bead Series MCB 0603 Size EIAJ Global RF/Component Solutions
MCB0603 Series Specification Product Name Chip Ferrite Bead Series MCB 0603 Size EIAJ 0603 Chip Ferrite Bead (MCB0603 Series) Engineering Spec. Monolithic inorganic material construction. Closed magnetic
Power Splitter/Combiner 2 Way-90 50Ω 5 to 11 GHz
MMIC Surface Mount Power Splitter/Combiner 2 Way-90 50Ω 5 to 11 GHz The Big Deal Wideband (5-11 GHz) Good Isolation and Return Loss Highly repeatable performance (GaAs based design) No external termination
3M 4-Wall, Tripolarized Header.050".100" Latch/Ejector, PTH & SMT Straight, PTH Right Angle 810 Series
Tripolarized for robust alignment when mating to 820 series socket 50 mil 100 mil halves the connector length vs. traditional 100 mil x 100 mil products Latching Ejector for rugged high performance applications
Used to help achieve electromagnetic compliance of end products Replace larger surface mount TVS Zeners in many applications.
RoHS Description The ML Series family of transient voltage surge suppression devices is based on the Littelfuse Multilayer fabrication technology. These components are designed to suppress a variety of
RF WIREWOUND CHIP INDUCTORS
RF WIREWOUND CHIP INDUCTORS These high frequency High-Q chip inductors feature a monolithic body made of low loss ceramic wound with wire to achieve optimal high frequency performance. These RF chip inductors
SMD Type Power Choke Coil
SMD Type Power Choke Coil Features 1.Lowest height in this package footprint. 2.Shielded construction. 3.Handles high transient current spikes without saturation. 4.Lowest DCR/μH, in this package size.
X2Y - series Surface-mount ceramic EMI filter
DISCRETE CERAMICS X2Y series Surface mount component June 2002 Rev 6 X2Y - series 2002 July 26 v1.07 www.yageo.com X2Y Series Table of Contents 1. Introduction, Benefits, Applications 2. Available Capacitances
YAGEO CORPORATION SMD INDUCTOR / BEADS. SCD Series. Dimensions : mm TYPE A B C D SCD TYP 1.2
YAGEO CORPORATION SMD INDUCTOR / BEADS SCD Series SMT Power Inductors shapes and dimensions TYPE DIMENSION Dimensions : mm SCD31 (1µH ~ 68µH) SCD43 (1µH ~ 68µH) 4.±.3 B TYPE A B C D SCD31 3.5 3. 1..6TYP
Semiteh Electronics. SMD1206 HF Series Surface Mount PTC Devices. SMD1206 HF Series APPROVAL SHEET. MODEL NO.: SMD1206 Series CUSTOMER:
APPROVAL SHEET MODEL NO.: SMD1206 Series CUSTOMER: CUSTOMER'S APPROVAL: AUTHORIZED SIGNATURE/STAMP DATE Surface Mount PTC Devices 1/7 Performance Specification Maximum Model Mar Resistance V max Imax I
MPS4101-6LP Datasheet 50 MHz 25 GHz RoHS-Compliant Control Device QFN SPST PIN
MPS4101-6LP Datasheet 50 MHz 25 GHz RoHS-Compliant Control Device QFN SPST PIN Microsemi Corporate Headquarters One Enterprise, Aliso Viejo, CA 92656 USA Within the USA: +1 (800) 713-4113 Outside the USA:
Atom FBM GENERAL S SERIES. Specification CHIP FERRITE BEAD MULTILAYER TYPE. Part No. InduSTance 1. Percent RDC 2 IDC Tolerance Max Max
CHIP FERRITE BEAD MULTILAYER TYPE FBM GENERAL S SERIES Specification Part No. InduSTance 1 Percent RDC 2 IDC Tolerance Max Max (MA) FBM 0402 ST 060 S 6 @ 100 MHZ S 0.05 500 FBM 0402 ST 100 S 10 @ 100 MHZ
LCA710STR. Single Pole, Normally Open OptMOS Relay INTEGRATED CIRCUITS DIVISION
LCA7 Single Pole, Normally Open OptMOS Relay Parameter Rating Units Blocking Voltage 6 V P Load Current A rms / A DC On-Resistance (max. Features Low On-Resistance:. High Current Handling Capability: A
Type 168/185 Metallized Polyester Radial Lead Capacitors
Radial Box Metallized Polyester Capacitors for Automatic Insertion The Type 168/185 series radial lead metallized polyester box capacitors are available in bulk (Type 168) or on ammo pack or tape and reel
Noise fi lter for various drive circuitry requiring high temp. operation and peak current handling capability Boost-Converter, Buck-Converter DC/DC
Power Choke Coil for utomotive application Series: PCC-M128MF (MC) High heat resistance and high reliability Using metal composite core (MC) Industrial Property : patents 3 (Registered 1/Pending 2) Features
2.6 GHz capable, 10 W carrying power (at 2.6 GHz), 50Ω/75Ω impedance and 1 Form C relays
.6 GHz capable, W carrying power (at.6 GHz), 5Ω/75Ω impedance and Form C relays RE RELAYS (ARE)..44..44 mm inch FEATURES Excellent high frequency characteristics (to.6ghz) Surface-mount type also available
MAS6240C Piezo Driver with Multi-Mode Charge Pump
DESCRIPTION MAS6240 is a piezo driver device that can drive outputs up to 18Vpp from 3V supply. An internal threemode charge pump generates boosted supply voltage for piezo driver. For adjusting the piezo
INPAQ Global RF/Component Solutions
TVL 0402 01 SP0 Specification Product Name Series Part No Transient Voltage Suppressor TVS Series TVL 0402 01 SP0 Size EIA 0402 TVL 0402 01 SP0 Engineering Specification 1. Scope TVL 0402 01 SP0 is a TVS
How to Order CB 03 Y T Y N 601
(General Use) Features Standard type used to suppress lower-frequency, lower current signals. Impedance over a broad frequency range. Suitable for flow and reflow soldering Available in 8 sizes. Applications
LCA110LSTR. Single Pole, Normally Open OptoMOS Relay INTEGRATED CIRCUITS DIVISION
LCA11L Single Pole, Normally Open OptoMOS Relay Parameter Ratings Units Blocking Voltage 3 V P Load Current 12 ma rms & ma DC On-Resistance (max 3 Features Built-in Current Limiting 37V rms Input/Output
PAA191STR. Dual Single-Pole, Normally Open OptoMOS Relays INTEGRATED CIRCUITS DIVISION
Dual Single-Pole, Normally Open OptoMOS Relays Parameter Rating Units Load Voltage 4 V P Load Current ma rms / ma DC On-Resistance (max 8 Features V rms Input/Output Isolation Low Drive Power Requirements
APPLICATIONS Computers and peripheral equipment Consumer products High speed circuits Suitable for circuits with unstable ground PART NUMBERING SYSTEM
The ferrite beads have been developed to pass signal frequencies from 1MHz to 1MHz while exhibiting high impedance characteristics to reduce EMI noise above these specific frequencies. FEATURES Designed
INPAQ Global RF/Component Solutions
TVL 0402 01 AB1 Specification Product Name Series Part No Transient Voltage Suppressor TVS Series TVL 0402 01 AB1 Size EIA 0402 TVL 0402 01 AB1 Engineering Specification 1. Scope TVL 0402 01 AB1 is a TVS
LCA701. Single Pole, Normally Open OptoMOS Relay INTEGRATED CIRCUITS DIVISION
Single Pole, Normally Open OptoMOS Relay Parameter Rating Units Blocking Voltage V P Load Current. A rms / A DC On-Resistance (max). Input Control Current ma Features V P Blocking Voltage Operational Temperature
Film Chip Capacitors. PPS DIELECTRIC CB Series GENERAL DESCRIPTION ADVANTAGES APPLICATIONS PERFORMANCE CHARACTERISTICS
APPLICATIONS General purpose function in low voltage applications: Filtering, coupling, decoupling Time-constant Oscillation timing circuit Typical applications would be: Automotive (navigation system...)
LCA127LSTR. Single-Pole, Normally Open OptoMOS Relay INTEGRATED CIRCUITS DIVISION
Single-Pole, Normally Open OptoMOS Relay Parameter Ratings Units Blocking Voltage 2 V P Load Current 7 ma rms / ma DC On-Resistance (max Features Current Limiting 37V rms Input/Output Isolation Low Drive
LCA127STR. Single-Pole, Normally Open OptoMOS Relay INTEGRATED CIRCUITS DIVISION
Single-Pole, Normally Open OptoMOS Relay Parameter Ratings Units Blocking Voltage V P Load Current ma rms / ma DC On-Resistance (max Features 37V rms Input/Output Isolation Low Drive Power Requirements
DATA SHEET METAL LOW OHMIC JUMPER PA series
Product specification October 05, 2018 V.0 DATA SHEET METAL LOW OHMIC JUMPER PA series sizes 0201/ 0402/ 0603/ 0805 RoHS compliant & Halogen free Product specification 2 SCOPE This specification describes
ML Varistor Series. Surface Mount Varistors
Pb The ML Series family of Transient Voltage Surge Suppression devices is based on the Littelfuse Multilayer fabrication technology. These components are designed to suppress a variety of transient events,
500mW, 2% Tolerance SMD Zener Diode
500mW, 2% Tolerance SMD Zener Diode FEATURES - Wide zener voltage range selection : 2.4V to 75V - Surface mount device type - Moisture sensitivity level - Pb free and RoHS compliant - V Z Tolerance Selection
YM12S05 DC-DC Converter Data Sheet VDC Input; VDC 5A
The Products: Y-Series Applications Intermediate Bus Architectures Distributed Power Architectures Data communications Telecommunications Servers, workstations Benefits High efficiency no heat sink required
AQ24CANFD 200W TVS Diode Array
AQ24CANFD 200W TVS Diode Array RoHS Pb GREEN Description The AQ24CANFD is designed to protect automotive Controller Area Network (CAN lines from damage due to electrostatic discharge (ESD, electrical fast
Features Shielded construction Flat wire Unit height of 2 mm Inductance range: 0.22 to 5.6 μh Rated current up to 10 A RoHS compliant* DCR.
*RoHS COMPLIANT R68 Features Shielded construction Flat wire Unit height of 2 mm Inductance range:.22 to 5.6 μh Rated current up to 1 A RoHS compliant* This series is currently available but not recommended
SP pF SOT23-6L 4 Channels Diode Array
SP319.3pF SOT23-6L 4 Channels Diode Array RoHS Pb GREEN Description 4 5 6 3 2 1 SP312-3UTG Pinout *Pins 6, 7, 9, 1 are not internally connected but should be connected to the trace. 6 7 8 9 1 5 4 3 2 1
NMUSB2022PMC. 2 MOPP Powered Dual Port USB Data Isolator. FEATURES PRODUCT OVERVIEW
www.murata-ps.com FEATURES Isolated dual powered USB 2.0 compliant Surface mount module One upstream port, two isolated down stream ports Automatic switching between low (1.5Mbps) and full speed (12Mbps)
CDMSP M Surface Mount TVS Diode Array
*RoHS COMPLIANT Features RoHS compliant* Protects four I/O lines Ultra-low capacitance ~.55 pf ESD protection > kv Surge protection Applications High Definition Multimedia Interface (HDMI) Digital Visual
INPAQ Global RF/Component Solutions
TVN 0201 01 SP0 Specification Product Name Series Part No Transient Voltage Suppressor TVS Series TVN 0201 01 SP0 Size EIA 0201 TVN 0201 01 SP0 Engineering Specification 1. Scope TVN 0201 01 SP0 is a TVS
Model XDL S Rev A
Delay Line DESCRIPTION The XDL15-3-030S can be used in amplifier linearization applications from 135 2700Mhz. Small form factor of XDL15-3-030S is ideal for cascading to obtain longer delay. The Xinger
output voltage output current max (A)
date 12/21/2011 page 1 of 6 SERIES: VYC0W DESCRIPTION: DC-DC CONVERTER FEATURES up to 0 W output industry standard pinout :1 input range (9 ~ 6 V, 18 ~ 7 V) single, dual, and triple outputs 1,00 V isolation
AEM GcDiode TM ESD Suppressors
Part Number: ES0603V014BT, ES0402V014BT Features Glass ceramic monolithic structure Ultra low capacitance (0.25pF typical) Low leakage current (
TBU-KE Series - TBU High Speed Protectors
*RoHS COMPLIANT E2550 0072 Features Superior circuit protection Overcurrent and overvoltage protection Blocks surges up to rated limits High speed performance Small SMT package RoHS compliant* Agency recognition:
2R2. Design Code Design Code M ±20%
Wire Wound SMD Power Inductors WPN Series Operating Temp. : -40 ~+125 (Including self-heating) FEATURES Fe base metal material core provides large saturation current Metallization on ferrite core results
PM1206STR. AC Power Switch INTEGRATED CIRCUITS DIVISION
AC Power Switch Parameter Rating Units AC Operating Voltage 26 V rms Load Current 5 ma rms On-State Voltage Drop (I L =5mA rms ) 1.4 V rms Features Load Current up to.5a rms Blocking Voltages up to 6V
LCA182STR. Single Pole, Normally Open OptMOS Relay INTEGRATED CIRCUITS DIVISION
Single Pole, Normally Open OptMOS Relay Parameter Rating Units Blocking Voltage 3 V P Load Current 12 ma rms / ma DC On-Resistance (max 3 Input Control Current.2 ma Features Very Low Input Control Current
Product Specification. Mezza-pede SMT Connector Low Profile 1.0mm Pitch
Mezza-pede SMT Connector Low Profile 1.0mm Pitch Rev. 1 December 7, 2016 1.0 Scope This product specification applies to 1.0mm pitch Mezza-pede SMT Connectors, designed for the mating and unmating of a
0.4 mm Pitch, 1.5 mm Board-to-Board Connectors with Dual Shields
All non-rohs products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales
Multi-Layer Ferrite Chip Beads
Multi-Layer Ferrite Chip Beads ORDERING CODE... 1 External Dimensions... 2 Beads For Signal Lines(BF series)... 3 Beads For Power Lines (BP series)... 8 Beads For High Speed Signal Lines (BH series)...
TBU-DT Series - TBU High-Speed Protectors
*RoHS COMPLIANT Features n Superior circuit protection n Overcurrent and overvoltage protection n Blocks surges up to rated limits n High-speed performance n Small SMT package n RoHS compliant* n Agency
Low Profile, High Current IHLP Inductors
ow Profile, High Current IHP Inductors IHP-CZ-11 Manufactured under one or more of the following: US Patents; 6,198,37/6,,7/6,9,89/6,,. Several foreign patents, and other patents pending. STANDARD EECTRICA
NMUSB202MC Powered Dual Port USB Data Isolator
www.murata-ps.com System voltage rail/ External adapter Power Isolated DC-DC Converter LDO Linear Regulator USB Power Switch Isolated USB Port 1 USB 2.0 Device FEATURES Isolated dual powered USB 2.0 compliant
MX877RTR. 8-Channel, 60V Driver with Push-Pull Output, 3 Wire Interface INTEGRATED CIRCUITS DIVISION. Features. Description.
8-Channel, 6V Driver with Push-Pull Output, 3 Wire Interface Features Eight (8) Outputs Rated at 6V, ±8mA Push-Pull Driver Configuration 6V to 6V Driver Supply Range 2.7V to 5.5V Logic Supply Range 3-Wire
CPC1540GSTR. Features Integrated Active Current-Limit Protection Thermal Shutdown Guaranteed Turn-On: 2mA Input Control Current 350V P
Single-Pole, Normally Open OptoMOS Relay with Integrated Current Limit and Thermal Shutdown Parameter Rating Units Load Voltage 350 V P Load Current 120 ma Maximum On-Resistance 25 Input Control Current
Knowles Acoustics 1151 Maplewood Drive Itasca, IL 60143
Zero Height SiSonic Microphone Specification Knowles Acoustics 1151 Maplewood Drive Itasca, IL 60143 1of 10 1. DESCRIPTION AND APPLICATION 1.1 Description Zero Height Surface Mount Silicon Microphone 1.2
MADR TR. SPDT PIN Diode Driver Rev. V3. Features. Functional Block Diagram. Description. Pin Configuration. Ordering Information
Features Moderate Speed, CMOS Technology (25 ns) Complementary Outputs High Drive Current Capability (± 50 ) Low Current Consumption Plastic SOIC Body for SMT Applications Tape and Reel Packaging Available
MAS6240 Piezo Driver with Multi-Mode Charge Pump
MAS624 Piezo Driver with Multi-Mode Charge Pump Both Single Ended and Differential Output Three-Step Volume Adjusting Up to 8Vpp Output from 3V Supply One Wire Audio & Shutdown Control High Efficiency
AQxxC-01FTG Series 450W Bidirectional TVS Diode
General Purpose ESD Protection - AQxxC-1FTG Series AQxxC-1FTG Series 5W Bidirectional TVS Diode RoHS Pb GREEN Description The bidirectional AQxxC-1FTG Series is designed to replace multilayer varistors
SPECIFICATION. Bulk Acoustic Wave Filter W. DATE September 5, 2014 WISOL. Byun, Kyung-Su. User WISOL CO., LTD.
SPECIFICATION Bulk Acoustic Wave Filter USER USER PART No. WISOL PART No. DOC. No. DATE September 5, 2014 REVISION WISOL Hong, Byung-Chul Byun, Kyung-Su Mun, Gil-Seop ISSUED BY APPROVED BY (R&D) APPROVED
Specification Status: RELEASED
PAGE NO.: 1 OF 8 Specification Status: RELEASED GENERAL DESCRIPTION TE Circuit Protection PolyZen devices are polymer enhanced, precision Zener diode micro-assemblies. They offer resettable protection
Lighthouse LEDs. Technical Data Sheet. Customer Approval. Product Name. Part Number. Customer. Customer PN. Version.
Technical Data Sheet Product Name 0805 High Bright Purple Chip LED Part Number A-0805UUVC Customer Customer PN Version Date Customer Approval Instituted By Checked By: Approved By 1. Features: Package
APPLICATIONS. SRF TYP. (MHz) ± [3.0 ± 0.2] [2.0] Max. IHLP-1212BZ μh ± 20 % ER e3
![APPLICATIONS. SRF TYP. (MHz) ± [3.0 ± 0.2] [2.0] Max. IHLP-1212BZ μh ± 20 % ER e3](/thumbs/76/74099920.jpg "APPLICATIONS. SRF TYP. (MHz) ± [3.0 ± 0.2] [2.0] Max. IHLP-1212BZ μh ± 20 % ER e3")
IHP-1212BZ-11 IHP Commercial Inductors, ow DCR Series DESIGN SUPPORT TOOS click logo to get started Design Tools Available STANDARD EECTRICA SPECIFICATIONS 0 INDUCTANCE ± % AT khz, 0.25 V, 0 A (μh) DCR
Product Tape and Reel, Solderability & Package Outline Specification
Manufacturing Note MN-001 Product Tape and Reel, Solderability & Package Outline Specification Contents 1. General Information 2. Tape and Reel / T&R 3. Package Outline Drawing / POD 4. Electro Static
Low Profile, High Current IHLP Inductors
ow Profile, High Current IHP Inductors IHP-6767GZ-11 FEATURES Shielded construction Frequency range up to 7 khz owest DCR/μH, in this package size Manufactured under one or more of the following: US Patents;
FEATURES APPLICATIONS. IHLP-3232CZ-1L 4.7 μh ± 20 % RZ MODEL INDUCTANCE VALUE INDUCTANCE TOLERANCE PACKAGE CODE
IHP Tin/ead Inductors, ow DCR Series IHP-3232CZ-1 DESIGN SUPPORT TOOS click logo to get started Design Tools Available STANDARD EECTRICA SPECIFICATIONS INDUCTANCE ± % AT khz,.25 V, A (μh) DCR TYP. 25 C
Multi-Layer Ferrite Chip Beads
Multi-Layer Ferrite Chip Beads ODEING CODE BH 15 3 T T S 5 PODUCT CODE BF : For General Signal Lines BP : For Power Lines BH : For High Speed Signal Lines (1MHz~) BS : For Higher Speed Signal Lines (5MHz~)
INPAQ. Specification TVN AB0. Product Name Transient Voltage Suppressor Series TVS Series Part No TVN AB0 Size EIA 0201
TVN 0201 01 AB0 Specification Product Name Transient Voltage Suppressor Series TVS Series Part No TVN 020101 AB0 Size EIA 0201 TVN 0201 01 AB0 Engineering Specification 1. Scope TVN 0201 01 AB0 is a TVS
Motocraft Multilayer Varistor
MLV1005 / 1608 SERIES ENGINEERING SPECIFICATION 1. SCOPE (1) Lead free type (2) SMD type zinc oxide based ceramic chip (3) Insulator over coat keeps excellent low and stable leakage current (4) Plating
RF Chip Inductors WC701.I (11/04)
Wire-Wound - 42, 63, 85, 18, 126, 121 & 1812 RF Chip Inductors WC71.I (11/4) WIRE-WOUND RF CHIP INDUCTORS Pulse is one of the largest magnetic component design and manufacturing companies in the world.
Metal Oxide Varistor:TVB Series
Features. RoHS compliant 2. Available for SMT flow/reflow soldering 3. Low profile and space saving 4. Large capability to withstand high surge current 5. Low inductance construction with excellent response
DUBOX SHUNTS BOARD/WIRE-TO-BOARD CONNECTORS FEATURES & BENEFITS. Dual-beam contacts for added reliability
BOARD/WIRE-TO-BOARD CONNECTORS DUBOX SHUNTS FEATURES & BENEFITS Dual-beam contacts for added reliability Slotted cutout in low profile housing simplifies electrical testing Side-by-side and end-to-end
3M Ribbon Cable Socket and Header, Series 451 & " x.050" (1.27 mm x 1.27 mm)
1 of 8 3M Ribbon Cable Socket and Header, Series 451 & 452.050" x.050" (1.27 mm x 1.27 mm) Product Specification: 78-5102-0091-4 Revised: 05-01-2013 2 of 8 Page Cover Page..... 1 Contents 2 1. Scope......
NMUSB202MC Powered Dual Port USB Data Isolator
www.murata-ps.com System voltage rail/ External adapter Power Isolated DC-DC Converter LDO Linear Regulator USB Power Switch Isolated USB Port 1 USB 2.0 Device FEATURES Isolated dual powered USB 2.0 compliant
RTE02 and RTE03 Miniature Rotary Switches
RTE02 and RTE03 Miniature Rotary Switches RTE02 and RTE03 are two types of a subminiature rotary changeover switch to be mounted on PC boards. PC pins are in a 2.54 mm (0.100) grid. RTE02 with 2 positions
ML Varistor Series. Surface Mount Varistors. Features. Size Metric EIA
The ML Series family of Transient Voltage Surge Suppression devices is based on the Littelfuse Multilayer fabrication technology. These components are designed to suppress a variety of transient events,
Size Code .039±.004 (1.0±0.1).063±.004 (1.6±0.1) KQT0402 KQ ±.008 (2.0±0.2) KQ ±.008 (2.5±0.2) KQ1008. Packaging
K high inductor EU features Surface mount Operating temperature: - C ~ + C Flat top suitable for high speed pick-and-place components Excellent high frequency applications High factors and self-resonant
INPAQ Global RF/Component Solutions
TEA10201V05A0 Specification Product Name Series Part No ESD Guard TM TEA Series (Thin Film Air Gap) TEA10201V05A0 Size EIA 0201 TEA10201V05A0 Engineering Specification 1. Scope This specification is applied
SP pF 30kV Bidirectional Discrete TVS
SP1326 15pF 30kV Bidirectional Discrete TVS RoHS Pb GREEN Description The SP1326 back-to-back diodes are fabricated in a proprietary silicon avalanche technology. These diodes provide a high ESD (electrostatic
CPC1510GSTR. Single-Pole, Normally Open Relay with Integrated Current Limit INTEGRATED CIRCUITS DIVISION. Description
CPC Single-Pole, Normally Open Relay with Integrated Current Limit Parameter Rating Units Blocking Voltage 2 V P Load Current 2 ma rms / ma DC On-Resistance (max Features Integrated Active Current-Limit
FEATURES APPLICATIONS ± [6.47 ± 0.254]
![FEATURES APPLICATIONS ± [6.47 ± 0.254]](/thumbs/81/83604093.jpg "FEATURES APPLICATIONS ± [6.47 ± 0.254]")
IHP-CZ- IHP Commercial Inductors, High Saturation Series DESIGN SUPPORT TOOS click logo to get started Models Available STANDARD EECTRICA SPECIFICATIONS INDUCTANCE ± % AT khz,. V, A (μh) Design Tools Available
Product Tape and Reel, Solderability & Package Outline Specification
Manufacturing Note MN-001 Product Tape and Reel, Solderability & Package Outline Specification Contents 1. General Information 2. Tape and Reel / T&R 3. Package Outline Drawing / POD 4. Electro Static
VT-820 VT-820. Temperature Compensated Crystal Oscillator Previous Vectron Model VTM3. Description
VT-820 Temperature Compensated Crystal Oscillator Previous Vectron Model VTM3 VT-820 Description Vectron s VT-820 Temperature Compensated Crystal Oscillator (TCXO) is a quartz stabilized, clipped sine
MH Series High Current Chip Ferrite Beads
*ohs COMPLIANT & **HALOGEN FEE Features High resistance to heat and humidity esistance to mechanical shock and pressure Accurate dimensions for automatic surface mounting Wide impedance range ohs compliant*
ML Varistor Series. Surface Mount Varistors
The ML Series family of Transient Voltage Surge Suppression devices is based on the Littelfuse Multilayer fabrication technology. These components are designed to suppress a variety of transient events,
PGA / BGA / PLCC SOCKETS
PGA / BGA / PLCC SOCKETS QUICK SELECTOR CHART PGA / BGA / PLCC PGA BGA PLCC GRID 2.54 mm INTERSTITIAL 1.27 mm 1.27 mm 1 mm SOCKETS Solder tail 156 161 165 SEE PAGE 173 Surface mount 156 161 165 166 169
DC/DC Converters. TSM Series, 1 Watt. Features. Models
TSM Series, Watt Features SMD package (SOIC-4/8) Construction in lead frame technology Isolated single and dual output I/O isolation 000 VDC High efficiency Operating temperature 40 C to +85 C Reflow solder
SIM800H&L_ Secondary Reflow SMT _Guidelines_V1.00
SIM800H&L_ Secondary Reflow SMT _Guidelines_V1.00 Document Title: SIM800H&L_ Secondary Reflow SMT_Guidelines Version: 1.00 Date: 2013-08-30 Status: Document Control ID: Release SIM800H&L_ Secondary Reflow
LITE-ON TECHNOLOGY CORPORATION
Features * Meet ROHS, Green Product. * Extra thin (0.35H mm) Chip LED. * Extra bright AlInGaP Chip LED. * Package in 8mm tape on 7" diameter reels. * EIA STD package. * I.C. compatible. * Compatible with
LAMP UTC/S400-X9-L
Features Popular T-1 round package High luminous power Typical chromaticity coordinates x=0.29, y=0.28 according to CIE1931 Bulk, available taped on reel. The product itself will remain within RoHS compliant
TBU-DT Series - TBU High-Speed Protectors
Features n Superior circuit protection n Overcurrent and overvoltage protection n Blocks surges up to rated limits n High-speed performance n Small SMT package n RoHS compliant* n Agency listing: Applications