2 x Dynamic Arms on 135 Post with C-Clamp

Size: px

Start display at page:

Download "2 x Dynamic Arms on 135 Post with C-Clamp"

Jade Clarke
5 years ago
Views:

1 Installation Guide AWMS-2-D13-C 2 x Dynamic Arms on 135 Post with C-Clamp COMPONENT CHECKLIST RANGE A AWM-LC Post Clamp B AWM-AD Dynamic Arm (x2) C AWM-P Post D AWM-FC C-Clamp CONTENTS C-Clamp Page 2 Page Post Page 6 Page 7 Post Clamp Page 8 Page 9 Dynamic Arm Page 10 Page 11 Page 12 Page 13 AWM-FC Component Checklist Clamp Installation AWM-P13 Component Checklist Post Installation AWM-LC Component Checklist Post Clamp Installation AWM-AD Component Checklist Arm Installation Monitor Installation Cable Management AWMS-2-D13-C Page 1 of 13

2 C-Clamp AWM-FC COMPONENT CHECKLIST REQUIRED TOOLS All tools supplied A C Clamp A Bracket C Clamp Bracket C Cover for CPost Cover for Post E E 4mm Allen 4mmkey Allen key B C Clamp B Plate C Clamp Plate D Cover for DBase Cover for Base F F 5mm Allen 5mmkey Allen key IMPORTANT INFORMATION! Please ensure this product is installed as per these installation instructions.! This product is compatible with Atdec modular (AWM) products.! The manufacturer accepts no responsibility for incorrect installation. AWMS-2-D13-C Page 2 of 13

3 1. C Clamp overview 1.1 Default - This is the out of the box configuration 1.2 Inverted - The C Clamp can be reconfigured for thicker surfaces MIN THICKNESS - 25mm ( 1 ) MAX THICKNESS - 33mm ( 1 5 / 16 ) MIN THICKNESS - 18mm ( 11 / 16 ) MAX THICKNESS mm (1 ) 2. Re-configure Clamp 2.1 Slide pad off 2.3 Invert pad 2.3 Slide pad back on 3. Post mount configuration 3.1 Attach plate to post 3.2 Place in desired location 3.3 Slide the C Clamp bracket over the plate and position screw tips in the indents on the base plate Fasteners supplied with post! Tighten Firmly Note: You may need to un-screw the set screws out of the plate using the allen key 3.4 Check the set screws are mounted in position. Also check the desk clamp bracket is positioned tight up against the mounting surface edge 3.5 Tighten the set screws firmly and evenly on both sides of the desk clamp bracket. M8 x 16mm Set Screw Desk Clamp Bracket Mounting surface Pad AWMS-2-D13-C Page 3 of 13

4 4. Installing the clamp cover to post 4.1 Remove the cable cover by pulling it straight up and out of the post. Remove top cap if already installed 4.2 Locate the C Clamp cover over the post. Guide over the holes in the base plate and gently apply pressure on the cover until it clicks into place 4.3 Re-attach the cable cover by sliding it into the post channel. Fit the pole and cover caps back on. Click! 5. Base mount installation 5.1 Attach plate to base 5.2 Place the base and plate in desired location 5.3 Slide the bracket onto the base plate and position screw tips in the indents on the base plate Fasteners supplied with base! Tighten Firmly Note: You may need to un-screw the set screws out of the plate using the allen key 5.4 Check the set screws are mounted in position. Also check the desk clamp bracket is positioned tight up against the mounting surface edge 5.5 Tighten the set screws firmly and evenly on both sides of the desk clamp bracket! M8 x 16mm Set Screw Desk Clamp Bracket Mounting surface Pad AWMS-2-D13-C Page 4 of 13

5 6. Installing the clamp cover to base 6.1 Locate the Cover for Base over the base. Guide over the holes in the base plate and gently apply pressure on the cover unitl it clicks into place. 6.2 Installation Complete To continue with intallation of your monitor arm, refer to your monitor arm s installation guide. Click! AWMS-2-D13-C Page 5 of 13

6 Post AWM-P Post COMPONENT CHECKLIST B B Post Cap C Screw M8 (x2) M8 (x2) REQUIRED TOOLS All tools provided A Post A Post D D E E Cable Cable Cover Cover Cap Cap Cable Cable Cover Cover (not (not supplied supplied with with all posts) all posts) (not (not supplied with with all posts) all posts) F F Cable clips (not (not supplied with with all all posts) posts) IMPORTANT INFORMATION! Please ensure this product is installed as per these installation instructions.! This product is compatible with Atdec AWM Series products.! The manufacturer accepts no responsibility for incorrect installation. AWMS-2-D13-C Page 6 of 13

7 1. Attach Post to fixing (fixing sold seperately) 1.1 Follow the installation guide provided with your fixing to attach it to the post and fit it to the worksurface. AWM Fixing options Bolt Through FB FB Bolt Kit Bolt Through AWM-FB Through Kit Kit F Clamp FF FF F Clamp F AWM-FF Clamp Heavy FHDuty FH HD F F Clamp HD AWM-FH Clamp C Clamp FC FC C Clamp C AWM-FC Clamp Grommet AC-GC AC-GC Grommet Clamp Grommet Clamp AC-GC Clamp 2. Check post placement & arm positions 2.1 Do not mount a monitor arm on the rear channel of a post when the post is fixed to the desk using an F Clamp, Heavy Duty F Clamp, or C Clamp. Rear of Mounting Surface Rear Rear of Mounting Rear of Mounting of Mounting Surface Surface Surface F Clamp AWM-FF Heavy Duty F Clamp AWM-FH C Clamp AWM-FC 3. Cable cover position and post cap 3.1 To reposition the cable cover, pull it straight up and out of the post and insert it into any of the available channels 3.2 Optional cable cover positions 3.3 Fit post cap onto the top of the post Allen Key Cable Cover Post Cap Note: An allen key may be stored in the Post Cap. Note: The cable cover shown does not come with all posts Post 4. Cable clips and cover 4.1 Push the cable down into the cable clip. 4.2 Insert one side of the cable clip into the channel on the post assembly, then push in the other side. 4.3 Loop cable and insert into cable cover. 4.4 Feed remaining cable into the cover. Note: Cable clips do not come with all posts. Additional clips sold separately. atdec.com atdec.co.uk atdec.com.au No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice E AWMS-2-D13-C Page 7 of 13

8 Post Clamp AWM-P COMPONENT CHECKLIST REQUIRED TOOLS All tools provided A Post Clamp IMPORTANT INFORMATION! Please ensure this product is installed as per these installation instructions.! This product is compatible with AWM Series Arms, Posts and Wall Channels.! The manufacturer accepts no responsibility for incorrect installation. AWMS-2-D13-C Page 8 of 13

9 1. Fix Clamp to Post or Wall Channel 1.1 Ensure knob is undone. 1.2 Slide Post Clamp into channel. 1.3 Hold clamp in on post 2. Slide post clamp into channel3. Hold clamp in desired position on post a and turn knob to lock in place. knob to lock in place Push knob to aid insertion Tip: push knob to aid insertion 2. Set arm rotation to 180 (optional) 2. Remove rotation ring Note: default arm rotation is set to rotate Place the rotation ring in the desired postion 2.1 Remove plastic sleeve. 2.2 Remove rotation ring 2.3 Place rotation ring in the desired position. 2. Lift Default Position 360 Note: Place the rotation ring depending on what post channel the arm will be attached to. The tag should always face towards the user. 1. Press OR 180 Flipped Position Tag 3. Fit AWM Series arm to Post Clamp 3. Tighten set screw 3.1 Push arm onto clamp. 3.2 Ensure arm is fully clamp. 3.3 Tighten joint screw. o clamp 2. Ensure arm is fully pushed onto Note: Check the arm rotation is smooth Tip: after Check the tightening. arm rotation i smooth after tightening. Note: Arm sold separately atdec.com atdec.co.uk atdec.com.au No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice A - E02 AWMS-2-D13-C Page 9 of 13

10 Dynamic Arm AWM-AD COMPONENT CHECKLIST C C D D Screw Screw Screw Screw M4x25mm M4x25mm M4x16mm E E Screw Screw M4x12mm REQUIRED TOOLS Phillips Head Screwdriver A Dynamic A Dynamic Monitor Arm Monitor Arm B VESA B Head VESA head F Spacer F Spacer G Security G Screw Security screw H 4mmH Allen 4mm Key allen key WEIGHT RANGE 0-9kg (0-20lbs) IMPORTANT INFORMATION! Please ensure this product is installed as per these installation instructions.! This product is compatible with Atdec AWM Series products.! The Dynamic Arm (AWM-AD) requires a Channel Clamp (AWM-LC, sold separately) for installation on an AWM Post.! The Dynamic Arm (AWM-AD) requires a Desk Base (AWM-LB, sold separately) for installation directly onto an AWM fixing.! The manufacturer accepts no responsibility for incorrect installation. AWMS-2-D13-C Page 10 of 13

11 1. Set arm rotation to 180 (optional) 1.1 On the Base or Channel Clamp (sold separately) Remove plastic sleeve. 1.2 Remove rotation ring. 1.3 Place rotation ring in the desired position. 2. Lift Default Position 360 Channel Clamp Ring Position When setting channel clamp rotation, orientate the ring depending on what post channel the arm will be attached to. The tag on the ring should always face towards the user. OR Press Flipped Position Tag 2. Fit arm onto Base or Channel Clamp (sold separately) 2.1 Push arm onto shaft. 2.2 Ensure arm is fully pushed onto shaft. 2.3 Tighten joint screw. Note: Check the arm rotation is smooth after tightening. 3. Attach VESA head to monitor 3.1 VESA mounting compatibility 100mm 75mm 100mm 75mm 3.2 Attach VESA head onto monitor with provided screws. Note: Spacers may be required for curved, recessed or uneven monitor surfaces. 3.3 Be sure to use correct screw length 5mm 12mm Flush Spacer Note: For other sizes, use a suitable adaptor plate (sold separately). Too long Too short 4. Mount monitor on arm 4.1 Insert VESA head into the monitor arm 4.2 Ensure that the VESA head sits flush within 4.3 Push the lever down to secure the monitor arm. There should be no gap. it to the arm assembly Monitor arm Gap No Gap AWMS-2-D13-C Page 11 of 13

12 5. Adjust tilt tension & install security screw 5.1 Use the allen key to adjust the tilt tension until the monitor holds in a vertical position at the end of the arm. 5.2 OPTIONAL security screw Tilt the head upwards to install the optional security screw. Note: Support monitor while adjusting. Loosen Loosen Tighten Tighten 6. Adjust arm tension 6.1 To accurately set the tension of the arm, position the monitor at 90 degrees 6.2 Use the allen key to adjust the arm tension to the weight of the monitor. Follow steps 6.3 to 6.5 to set the tension. 90 Heavier Monitor Lighter Monitor 6.3 If the monitor sags or falls down, increase the arm tension by rotating the screw clockwise. 6.4 If the monitor springs upwards from the bottom position, decrease the arm tension by rotating the screw anti-clockwise. 6.5 If the monitor floats or hovers in all positions the arm tension is balanced and does not require further adjustment. Monitor Falls (from top) Monitor Springs (from bottom) Monitor Floats (all positions) Increase Tension Reduce Tension Balanced 7. Tension gauge 7.1 When installing multiple monitors of a similar weight, use the tension gauge to make installation faster. Arm Tension Gauge Marker 1. Set up one monitor and record the position of the marker on the gauge. 2. When installing subsequent monitors, pre-tension the arm to the recorded amount, then fine-tune the tension by following steps 6.3 to 6.5. AWMS-2-D13-C Page 12 of 13

13 6. Monitor arm cable management 8. Cable management 6.1 Plug cables into the monitor and route 8.1 the Plug cables cables down into the the arm monitor using the and cable route hooks the and cables clips down the arm using the cable hooks and clips. Push See steps 8.2 to 8.4 Note Ensure enough cable slack Important! is given to allow for movement Ensure enough of the cable monitor slack is given in this area to allow for movement of the monitor. 7. Post cable management 8.2 Wedge cable into the central gap and slide it down the arm. 8.3 The cable should slip into the arm cavity 8.4 Slide the remaining loose cable from the central gap up the arm. 7.3 Recommended post cable cover position for double or triple arm set-ups Alternative cable cover positions No portion of this document or any artwork contained herein should be reproduced in any way without No the portion express of written this document consent of or Atdec any artwork Pty Ltd. contained Due to continuing herein should product be reproduced development, in any the way manufacturer without the reserves express the written right to consent alter specifications of Atdec Pty without Ltd. Due notice. to continuing C product development, the manufacturer reserves the right to alter specifications without notice atdec.com atdec.co.uk atdec.com.au atdec.com atdec.co.uk atdec.com.au AWMS-2-D13-C AWM-A46 Page Page 134 of of 134 AWM-AD Page 4 of 4

EVOLVE1-M MONITOR ARM

EVOLVE1-M MONITOR ARM EVOLVE1-M Rev A 2/17 Model EVOLVE1-M-SLV Model EVOLVE1-M-BLK Model EVOLVE1-M-WHT ASSEMBLY AND ADJUSTMENT EVOLVE1-M MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before