TEST REPORT. For ELECTRONICS TECHNOLOGY (DONG GUAN) COMPANY LIMITED ETSI EN V1.4.1 ( ) ETSI EN V1.8.

Transcription

1 TEST REPORT For ELECTRONICS TECHNOLOGY (DONG GUAN) COMPANY LIMITED No.161, Xin Min Road, Tong Luo Wei Industrial Zone, Jin Xia, Chang An Town, Dong Guan City, Guang Dong Province, China ETSI EN V1.4.1 ( ) ETSI EN V1.8.1 ( ) Model: M430-2, M430-3, M500-2, M500-3, S430-2, S430-3, S500-2, S500-3, T430-2, T500-2, T500-3, E500, N430, N500, ME500-E, D4-43MD-11, D4-43MD-12, D4-43MD-13, D4-43MD-14, D4-43MD-15, D4-43MD-21, D4-43MD-22, D4-43MD-23, D4-43MD-24, D4-43MD-25, D4-43MD-31, D4-43MD-32, D4-43MD-33, D4-43MD-34, D4-43MD-35, D4-50MD-01, D4-50MD-02, D4-50MD-03, D4-50MD-04, D4-50MD-05, MDT501, TP501, MDT511, TP511 Report Type: Original Report Product Type: GPS Test Engineer: Report Number: Jimmy Xiao RSZ Report Date: Merry Zhao Reviewed By: Test Laboratory: EMC Engineer Bay Area Compliance Laboratories Corp. (Shenzhen) 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China Tel: Fax: Note: This test report is prepared for the customer shown above and for the equipment described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP*, or any agency of the Federal Government. * This report contains data that are not covered by the NVLAP accreditation and are marked with an asterisk (Rev.2)

2 TABLE OF CONTENTS GENERAL INFORMATION... 4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT)... 4 OBJECTIVE... 4 RELATED SUBMITTAL(S)/GRANT(S)... 4 TEST METHODOLOGY... 4 TEST FACILITY... 5 SYSTEM TEST CONFIGURATION... 6 JUSTIFICATION... 6 EUT EXERCISE SOFTWARE... 6 SPECIAL ACCESSORIES... 6 EQUIPMENT MODIFICATIONS... 6 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS... 6 EXTERNAL I/O CABLE... 6 CONFIGURATION OF TEST SETUP... 7 BLOCK DIAGRAM OF TEST SETUP...7 SUMMARY OF TEST RESULTS... 8 ETSI EN V1.4.1 ( ) CONDUCTED EMISSIONS... 9 MEASUREMENT UNCERTAINTY... 9 EUT SETUP... 9 EMI TEST RECEIVER SETUP TEST EQUIPMENT LIST AND DETAILS TEST PROCEDURE TEST RESULTS SUMMARY TEST DATA ETSI EN V1.4.1 ( ) 7.1- RADIATED EMISSIONS MEASUREMENT UNCERTAINTY TEST SYSTEM SETUP EMI TEST RECEIVER SETUP TEST EQUIPMENT LIST AND DETAILS TEST PROCEDURE CORRECTED AMPLITUDE & MARGIN CALCULATION TEST RESULTS SUMMARY TEST DATA ETSI EN V1.4.1 ( ) 7.2 RF ELECTROMAGNETIC FIELD ( MHz and MHz) TEST EQUIPMENT TEST SYSTEM SETUP TEST STANDARD TEST PROCEDURE TEST DATA AND SETUP PHOTO ETSI EN V1.4.1 ( ) RF COMMON MODE TEST EQUIPMENT TEST SETUP TEST STANDARD Report No.: RSZ Page 2 of 43 ETSI EN V1.8.1 ( )

3 TEST PROCEDURE TEST DATA AND SETUP PHOTO EXHIBIT A- EUT PHOTOGRAPHS EUT FRONT VIEW EUT REAR VIEW EUT TOP VIEW EUT BOTTOM VIEW EUT LEFT SIDE VIEW EUT RIGHT SIDE VIEW EUT UNCOVER VIEW EUT MAIN BOARD WITH SHIELD TOP VIEW EUT MAIN BOARD WITH SHIELD OFF TOP VIEW EUT MAIN BOARD WITH SHIELD OFF TOP VIEW EUT MAIN BOARD WITH SHIELD BOTTOM VIEW EUT MAIN BOARD WITH SHIELD OFF BOTTOM VIEW EUT LCD TOP VIEW EUT LCD BOTTOM VIEW EUT GPRS MODULE WITH SHIELD TOP VIEW EUT GPRS MODULE WITH SHIELD OFF TOP VIEW EUT GPRS MODULE BOTTOM VIEW EUT GPS MODULE WITH SHIELD TOP VIEW EUT GPS MODULE WITH SHIELD OFF TOP VIEW EUT GPS MODULE BOTTOM VIEW EUT BLUETOOTH ANTENNA VIEW EUT GSM ANTENNA VIEW EUT GSM ANTENNA LOCATION VIEW EUT WIFI ANTENNA TOP VIEW EUT WIFI ANTENNA BOTTOM VIEW EUT ACCESSORY VIEW EUT BATTERY TOP VIEW EUT BATTERY BOTTOM VIEW EUT ADAPTER VIEW EUT ADAPTER INFORMATION VIEW EUT ADAPTER UNCOVERVIEW EUT ADAPTER MAIN BOARD TOP VIEW EUT ADAPTER MAIN BOARD BOTTOM VIEW EXHIBIT B- TEST SETUP PHOTOGRAPHS CONDUCTED DISTURBANCE AT DC TERMINALS - FRONT VIEW CONDUCTED DISTURBANCE AT DC TERMINALS - SIDE VIEW RADIATED DISTURBANCE FRONT VIEW (BELOW 1GHZ) RADIATED DISTURBANCE - REAR VIEW (BELOW 1GHZ) RADIATED DISTURBANCE FRONT VIEW (ABOVE 1GHZ) RADIATED DISTURBANCE - REAR VIEW (ABOVE 1GHZ) PRODUCT SIMILARITY DECLARATION LETTER Report No.: RSZ Page 3 of 43 ETSI EN V1.8.1 ( )

4 GENERAL INFORMATION Product Description for Equipment Under Test (EUT) The ELECTRONICS TECHNOLOGY(DONG GUAN)COMPANY LIMITED s product, model E500, or the "EUT" as referred to this report is a GPS, which measures approximately: 14.9 cm (L) x 9.7 cm (W) x 2.3 cm (H), rated input voltage: DC 3.7 V Battery or DC12-24V power source. Adapter information: Model: SW A; Input: DC 12-24V 2.5A; Output: DC 5V/2A *Note: The serial product model M430-2, M430-3, M500-2, M500-3, S430-2, S430-3, S500-2, S500-3, T430-2, T500-2, T500-3, E500, N430, N500, ME500-E, D4-43MD-11, D4-43MD-12, D4-43MD-13, D4-43MD-14, D4-43MD-15, D4-43MD-21, D4-43MD-22, D4-43MD-23, D4-43MD-24, D4-43MD-25, D4-43MD-31, D4-43MD-32, D4-43MD-33, D4-43MD-34, D4-43MD-35, D4-50MD-01, D4-50MD-02, D4-50MD-03, D4-50MD-04, D4-50MD- 05, MDT501, TP501, MDT511, TP511, all the models are electrically identical, only their difference is model name, and we select model E500 for the testing in this report, which was explained in the attached declaration letter. All measurement and test data in this report was gathered from production sample serial number: (Assigned by BACL, Shenzhen). The EUT was received on Objective The following report is prepared on behalf of ELECTRONICS TECHNOLOGY(DONG GUAN)COMPANY LIMITED in accordance with ETSI EN V1.4.1 ( ), Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility (EMC) standard for radio equipment and services; Part 3: Specific conditions for Short-Range Device (SRD) operating on frequencies between 9 khz and 40 GHz. The objective of the manufacturer is to determine compliance of the EUT with ETSI EN V1.4.1 ( ). Related Submittal(s)/Grant(s) No Related Submittals. Test Methodology All measurements contained in this report were conducted with ETSI EN V1.8.1 ( ). Report No.: RSZ Page 4 of 43 ETSI EN V1.8.1 ( )

5 Test Facility The Test site used by Bay Area Compliance Laboratories Corp. (Shenzhen) to collect test data is located on the 6/F, the 3rd Phase of WanLi Industrial Building, ShiHua Road, FuTian Free Trade Zone Shenzhen, Guangdong, China. Test site at Bay Area Compliance Laboratories Corp. (Shenzhen) has been fully described in reports submitted to the Federal Communication Commission (FCC). The details of these reports have been found to be in compliance with the requirements of Section of the FCC Rules on December 06, The facility also complies with the radiated and AC line conducted test site criteria set forth in ANSI C The Federal Communications Commission has the reports on file and is listed under FCC Registration No.: The test site has been approved by the FCC for public use and is listed in the FCC Public Access Link (PAL) database. Additionally, Bay Area Compliance Laboratories Corp. (Shenzhen) is an ISO/IEC accredited laboratory, and is accredited by National Voluntary Laboratory Accredited Program (Lab Code ). The current scope of accreditations can be found at Report No.: RSZ Page 5 of 43 ETSI EN V1.8.1 ( )

6 SYSTEM TEST CONFIGURATION Justification The system was configured for testing in a typical fashion (as normally used by a typical user). EUT Exercise Software N/A Special Accessories The special accessories were supplied by Bay Area Compliance Laboratories Corp. (Shenzhen). Equipment Modifications No modifications were made to the unit tested. Local Support Equipment List and Details Manufacturer Description Model Serial Number MEGURO GPS Signal Generator MSG-2050 N/A External I/O Cable Cable Description Length (M) From/Port To Unshielded detachable Power Cable 1.5 adapter EUT Report No.: RSZ Page 6 of 43 ETSI EN V1.8.1 ( )

7 Configuration of Test Setup GPS generator Horn Antenna EUT Adapter Block Diagram of Test Setup AC Power Source GPS generator LISN Horn Antenna EUT 10 cm Adapter 1.0 Meter Non-Conducting Table 80 cm above Ground Plane 1.5 Meter Report No.: RSZ Page 7 of 43 ETSI EN V1.8.1 ( )

8 SUMMARY OF TEST RESULTS ETSI EN V1.4.1 ( ) Rules Description of Test Result Reference to clauses EN AC mains power input/output ports Reference to clauses EN DC power input/output ports Reference to clauses EN Enclosure of ancillary equipment measured on a stand alone basis Reference to clauses EN Harmonic current emissions (AC mains input port) Reference to clauses EN Voltage fluctuations and flicker (AC mains input port) N/A Compliance Compliance 7.1 Reference to clauses EN Telecommunication ports N/A N/A N/A Reference to clauses EN Radio frequency electromagnetic field (80 MHz to MHz and MHz to MHz)(EN ) Reference to clauses EN Electrostatic discharge (EN ) Reference to clauses EN Fast transients, common mode (EN ) Reference to clauses EN Radio frequency, common mode (EN ) Reference to clauses EN Transients and surges in the vehicular environment (ISO ) Reference to clauses EN Surges (EN ) Reference to clauses EN Voltage dips and interruptions (EN ) Compliance N/A N/A Compliance N/A N/A N/A N/A- Please refer to applicability overview tables in sections 7.1 and 7.2 of EN requirements. Report No.: RSZ Page 8 of 43 ETSI EN V1.8.1 ( )

9 ETSI EN V1.4.1 ( ) CONDUCTED EMISSIONS Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, and LISN. Based on CISPR , The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of any conducted emissions measurement at Bay Area Compliance Laboratories Corp. (Shenzhen) is +2.4 db.(k=2, 95% level of confidence) EUT Setup The setup of EUT is according with per ETSI EN measurement procedure. The specification used was with the ETSI EN limits. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. The car adapter was connected to DC 12V or DC 24V power source. Report No.: RSZ Page 9 of 43 ETSI EN V1.8.1 ( )

10 EMI Test Receiver Setup The EMI test receiver was set to investigate the spectrum from 150 khz to 30 MHz. During the conducted emission test, the EMI test receiver was set with the following configurations: Frequency Range IFBW 150 khz 30 MHz 9 khz Test Equipment List and Details Manufacturer Description Model Serial Number Calibration Date Calibration Due Date Rohde & Schwarz EMI Test Receiver ESCS / Rohde & Schwarz L.I.S.N. ESH2-Z / * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test Procedure During the conducted emission test, the car adapter was connected to the outlet of the LISN. Maximizing procedure was performed on the six (6) highest emissions of the EUT. All data was recorded in the Quasi-Peak and average detection mode. Test Results Summary According to the recorded data in following table, the EUT complied with the ETSI EN , with the worst margin reading of: 9.16 db at MHz in the Positive conducted mode Test Data Environmental Conditions Temperature: 25 C Relative Humidity: 48 % ATM Pressure: kpa * The testing was performed by Jimmy Xiao on Report No.: RSZ Page 10 of 43 ETSI EN V1.8.1 ( )

11 Test Mode: GPS Receiving(worst case) Positive: Frequency (MHz) Cord. Result (dbμv) Correct Factor (db) Limit (dbμv) Margin (db) Remark (PK/QP/Ave.) Ave Ave Ave Ave Ave QP QP Ave QP QP QP QP Report No.: RSZ Page 11 of 43 ETSI EN V1.8.1 ( )

12 Negative: Frequency (MHz) Cord. Result (dbμv) Correct Factor (db) Limit (dbμv) Margin (db) Remark (PK/QP/Ave.) Ave Ave Ave Ave Ave QP Ave QP QP QP QP QP Report No.: RSZ Page 12 of 43 ETSI EN V1.8.1 ( )

13 ETSI EN V1.4.1 ( ) 7.1- RADIATED EMISSIONS Measurement Uncertainty All measurements involve certain levels of uncertainties, especially in field of EMC. The factors contributing to uncertainties are spectrum analyzer, cable loss, antenna factor calibration, antenna directivity, antenna factor variation with height, antenna phase center variation, antenna factor frequency interpolation, measurement distance variation, site imperfections, mismatch (average), and system repeatability. Based on CISPR , The Treatment of Uncertainty in EMC Measurements, the best estimate of the uncertainty of a radiation emissions measurement at Bay Area Compliance Laboratories Corp.(Shenzhen) is +4.0 db.(k=2, 95% level of confidence) Test System Setup The radiated emission tests were performed in the 3 meters chamber, using the setup accordance with the ETSI EN V ( ). The specification used was the ETSI EN V ( ). EMI Test Receiver Setup The system was investigated from 30 MHz to 6000 MHz. During the radiated emission test, the EMI test receiver Setup was set with the following configurations: Frequency Range RBW VBW Detector 30 MHz 1000 MHz 100 khz 300 khz QP 1000 MHz 6000 MHz 1 MHz 3 MHz Peak 1000 MHz 6000 MHz 1 MHz 10Hz Ave Report No.: RSZ Page 13 of 43 ETSI EN V1.8.1 ( )

14 Test Equipment List and Details Manufacturer Description Model Serial Calibration Calibration Number Date Due Date HP Amplifier HP8447D 2944A Rohde & Schwarz EMI Test Receiver ESCI Sunol Sciences Broadband Antenna JB1 A Mini-Circuits Amplifier ZVA-213+ T-E27H Sunol Sciences Horn Antenna DRH-118 A Rohde & Schwarz Spectrum Analyzer FSEM / * Statement of Traceability: Bay Area Compliance Laboratories Corp. attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test Procedure For the radiated emissions test, the car adapter was connected to DC12V /24 V power source. Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. The data was recorded in the Quasi-peak detection mode for below 1 GHz, and peak and average for above 1 GHz. Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter reading. The basic equation is as follows: Corr. Amp. =Meter Reading + Antenna Factor+ Cable Loss - Amplifier Gain The Margin column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit. Corrected Amp. Test Results Summary According to the data in the following table, the EUT complied with the ETSI EN V1.8.1 ( ), with the worst margin reading of: 10.5 db at MHz in the Horizontal polarization Report No.: RSZ Page 14 of 43 ETSI EN V1.8.1 ( )

15 Test Data Environmental Conditions Temperature: 25 C Relative Humidity: 56 % ATM Pressure: kpa The testing was performed by Jimmy Xiao on Test Mode: GPS receiving (worst case) Level in db ÌV/ M M G Frequency in Hz Frequency (MHz) Corrected Amplitude (dbµv/m) Antenna Height (cm) Ant. Polarity Turntable Position (deg) Correction Factor (db) Limit (dbµv/m) Margin (db) V V V V V H Note: above 1GHz, the data which below the limit 20dB was not recorded. Report No.: RSZ Page 15 of 43 ETSI EN V1.8.1 ( )

16 ETSI EN V1.4.1 ( ) 7.2 RF ELECTROMAGNETIC FIELD ( MHz and MHz) Test Equipment Manufacturer Description Model Serial Number Calibration Date Calibration Due Date Amplifier Research Amplifier 200W1000/M Amplifier Research Field Meter FM Amplifier Research Sensor FP HP Signal Generator HP8657A 2849U Amplifier Research Biconilog Antenna AT HP Synthesized Sweeper HP8341B 2624A Sunol Sciences Horn Antenna DRH-118 A * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attests that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test System Setup Anechoic Chamber 300 cm EUT System Wooden table 80 cm Power Amp Signal Generator Report No.: RSZ Page 16 of 43 ETSI EN V1.8.1 ( )

17 Test Standard Test level ETSI EN V1.8.1 ( ) / EN :2006 Test level 2 at 3V / m, (unmodulated, r.m.s.) Performance criterion: A Level Field Strength (V/m) X. Special Test Procedure The EUT and its simulators are placed on a turn table which is 0.8 meter above the ground. The EUT is set 3 meters away from the transmitting antenna which is mounted on an antenna tower. Both horizontal and vertical polarizations of the antenna are set on test. Each of the four sides of EUT must be faced this transmitting antenna and measured individually. In order to judge the EUT performance, a CCD camera is used to monitor the EUT. All the scanning conditions are as follows: Condition of Test Remarks Field Strength 3 V/m (Test level 2) 2. Radiated Signal 80% AM (1 khz) 3. Scanning Frequency MHz and MHz 4. Sweeping time of radiated decade/s 5. Dwell Time 1Sec. Test Data and Setup Photo Environmental Conditions Temperature: 24 C Relative Humidity: 50 % ATM Pressure: kpa * The testing was performed by Jimmy Xiao on Report No.: RSZ Page 17 of 43 ETSI EN V1.8.1 ( )

18 Test Mode: GPS Receiving Frequency Front Side (3V/m) Rear Side (3V/m) Left Side (3V/m) Right Side (3V/m) Range (MHz) VERT HORI VERT HORI VERT HORI VERT HORI A A A A A A A A A A A A A A A A RS ( MHz) Report No.: RSZ Page 18 of 43 ETSI EN V1.8.1 ( )

19 RS ( MHz) Test Setup Photo Report No.: RSZ Page 19 of 43 ETSI EN V1.8.1 ( )

20 ETSI EN V1.4.1 ( ) RF COMMON MODE Test Equipment Manufacturer Description Model Serial Number Calibration Date Calibration Due Date EM Test C/S Tester CWS EM Test Attenuator 6dB * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Shenzhen) attested that all calibrations have been performed in accordance to NVLAP requirements, traceable to the NIST. Test Setup SG CDN EUT Wooden Table 10 cm Test Standard ETSI EN V1.8.1/EN :2009 Test level 2 at 3 V (unmodulated e.m.f.), 0.15 MHz ~ 80 MHz, Test Level Performance Criterion: A Voltage Level (e.m.f.) Level (U 0 ) X Special Report No.: RSZ Page 20 of 43 ETSI EN V1.8.1 ( )

21 Test Procedure 1) Let the EUT work in test mode and test it. 2) The EUT are placed on an insulating support 0.1 m high above a ground reference plane. CDN (coupling and decoupling device) is placed on the ground plane about 0.3 m from EUT. Cables between CDN and EUT are as short as possible, and their height above the ground reference plane shall be between 30 and 50 mm (where possible). 3) The disturbance signal described below is injected to EUT through CDN. 4) The EUT operates within its operational mode(s) under intended climatic conditions after power on. 5) The frequency range is swept from 150 khz to 80 MHz using 3V signal level, and with the disturbance signal 80% amplitude modulated with a 1KHz sine wave. 6) The rate of sweep shall not exceed 1.5*10-3decades/s. Where the frequency is swept incrementally, the step size shall not exceed 1% of the start and thereafter 1% of the preceding frequency value. 7) Recording the EUT operating situation during compliance testing and decide the EUT immunity criterion. Test Data and Setup Photo Environmental Conditions Temperature: 25 C Relative Humidity: 50 % ATM Pressure: kpa * The testing was performed by Jimmy Xiao on Test Mode: GPS Receiving Frequency range: 150 khz to 80 MHz Modulation: Amplitude 80%, 1 khz sine wave Test level: 3V e.m.f., unmodulated Level Voltage Level (e.m.f.) (U 0 ) Pass 1 1 / / 2 3 A / 3 10 / / X Special / / Fail Report No.: RSZ Page 21 of 43 ETSI EN V1.8.1 ( )

22 Test Setup Photo Report No.: RSZ Page 22 of 43 ETSI EN V1.8.1 ( )

23 EXHIBIT A- EUT PHOTOGRAPHS EUT Front View EUT Rear View Report No.: RSZ Page 23 of 43 ETSI EN V1.8.1 ( )

24 EUT Top View EUT Bottom View Report No.: RSZ Page 24 of 43 ETSI EN V1.8.1 ( )

25 EUT Left Side View EUT Right Side View Report No.: RSZ Page 25 of 43 ETSI EN V1.8.1 ( )

26 EUT Uncover View EUT Main Board with Shield Top View Report No.: RSZ Page 26 of 43 ETSI EN V1.8.1 ( )

27 EUT Main Board with Shield off Top View-1 EUT Main Board with Shield off Top View-2 Report No.: RSZ Page 27 of 43 ETSI EN V1.8.1 ( )

28 EUT Main Board with Shield Bottom View EUT Main Board with Shield off Bottom View Report No.: RSZ Page 28 of 43 ETSI EN V1.8.1 ( )

29 EUT LCD Top View EUT LCD Bottom View Report No.: RSZ Page 29 of 43 ETSI EN V1.8.1 ( )

30 EUT GPRS Module with Shield Top View EUT GPRS Module with Shield off Top View Report No.: RSZ Page 30 of 43 ETSI EN V1.8.1 ( )

31 EUT GPRS Module Bottom View EUT GPS module with Shield Top View Report No.: RSZ Page 31 of 43 ETSI EN V1.8.1 ( )

32 EUT GPS module with Shield off Top View EUT GPS module Bottom View Report No.: RSZ Page 32 of 43 ETSI EN V1.8.1 ( )

33 EUT Bluetooth Antenna View EUT GSM Antenna View Report No.: RSZ Page 33 of 43 ETSI EN V1.8.1 ( )

34 EUT GSM Antenna Location View EUT WIFI Antenna Top View Report No.: RSZ Page 34 of 43 ETSI EN V1.8.1 ( )

35 EUT WIFI Antenna Bottom View EUT Accessory View Report No.: RSZ Page 35 of 43 ETSI EN V1.8.1 ( )

36 EUT Battery Top View EUT Battery Bottom View Report No.: RSZ Page 36 of 43 ETSI EN V1.8.1 ( )

37 EUT Adapter View EUT Adapter Information View Report No.: RSZ Page 37 of 43 ETSI EN V1.8.1 ( )

38 EUT Adapter UncoverView EUT Adapter Main board top View Report No.: RSZ Page 38 of 43 ETSI EN V1.8.1 ( )

39 EUT Adapter Main board bottom View Report No.: RSZ Page 39 of 43 ETSI EN V1.8.1 ( )

40 EXHIBIT B- TEST SETUP PHOTOGRAPHS Conducted Disturbance at DC Terminals - Front View Conducted Disturbance at DC Terminals - Side View Report No.: RSZ Page 40 of 43 ETSI EN V1.8.1 ( )

41 Radiated Disturbance Front View (below 1GHz) Radiated Disturbance - Rear View (below 1GHz) Report No.: RSZ Page 41 of 43 ETSI EN V1.8.1 ( )

42 Radiated Disturbance Front View (above 1GHz) Radiated Disturbance - Rear View (above 1GHz) Report No.: RSZ Page 42 of 43 ETSI EN V1.8.1 ( )

43 PRODUCT SIMILARITY DECLARATION LETTER *****END OF REPORT***** Report No.: RSZ Page 43 of 43 ETSI EN V1.8.1 ( )