Robot technology. Drive technology. Control technology. Welding. Training Overview

Transcription

1 Robot technology Drive technology Control technology Welding Training Overview

2 Invest in your future. Focus on knowledge and education. One key to success is the appropriate education of your staff. The YASKAWA Academy offers you a broad range of courses tailored to the level of knowledge of the participants from entry-level to expert. Our customers are the experts when it comes to solving concrete problems practically. Our products are tools that enable our customers to effectively realize the developed solutions. However, to get the most from the products, it is necessary to obtain accurate knowledge about the functionality of the components and what gains more and more in importance to recognise the interaction of the products in the group system and to exploit opportunities. Exactly that is the task of our YASKAWA Academy, namely imparting this knowledge to our customers. Our team is in the position to provide broad and detailed expert knowledge about our products but also to discuss solutions in dialogue with our customers: from the product to the solution! Control technology, drive technology and robotics grow together more and more in concrete applications. It is therefore only logical that the YASKAWA Academy now offers an integrated training approach, which embraces all YASKAWA product lines. For the benefit of our customers! Manfred Stern President & COO, YASKAWA Europe GmbH

3 Table of Contents YASKAWA Academy 0 Table of Contents Introduction Total System Solution Service Philosophy TCS Welcome to the YASKAWA Academy Robotics Academy Eschborn Training staff Eschborn Academy Allershausen... 0 Training staff Allershausen... The road to qualification... Course Structure... Operator and Programming Training... 4 Welding MotoWeld RL Robotics Maintenance Training... 8 Software Training... 4 Certification Programme Robotics... 8 Open Training... 9 On-site Training Mobile Training Cell... 4 Drive technology Academy Eschborn... 4 Training staff Eschborn... 4 Training Frequency Inverter Machine Control / Servo-Drive Technology Controll technology Academy Herzogenaurach Training staff Herzogenaurach Training SIMATIC S7 / MOVICON Teleservice / VIPA meets YASKAWA Basic Registration... 5 General Terms and Conditions for Training Courses... 5 How to find us... 5

4 04 YASKAWA Academy Introduction This investment will certainly pay off! Your SUCCESS is our MOTIVATION Learn this rather than that and under perfect conditions that promises the YASKAWA Academy to you. The key to your success is also the motivation of each individual YASKAWA Academy employee, namely excellent training and advanced education. Axel Burscheid General Manager, Total Customer Support Robotics Division, Yaskawa Europe GmbH Come and benefit from our advanced training concept. Starting right away, we offer training in all product areas of the YASKAWA group. These include training in the fields of robotics, drive and control technology. This offer of diversified and wide-range training stems from a single source. Our course programme is modular and offers the right training module for nearly all applications and every level of knowledge. Many participants praise our balanced approach, in which the practical application is being moved in the foreground next to the theoretical parts of the course. In this manner, we guarantee efficient and practice-oriented learning and ensure that the acquired knowledge can be applied directly on returning to the company. Our team of trainers is always on the knowledge forefront concerning automation technology due to ongoing advanced training. The trainers at the YASKAWA Academy gladly create a training concept based on your request with your individual and customized expectations. Motivate your employees, increase user safety and reduce downtime through targeted advanced training at the YASKAWA Academy. With our training programme we want to: n Impart them with knowledge to enable proper action n Give you security and confidence in your facility n Provide you and your employees with further qualifications through training for facility availability To secure your robotic systems at a high level n To support you at an early stage so that problems find no foothold n Assist you with your processes and thus help to optimize and secure the productivity of your facility n With increasing yield from your facility n To guarantee your success. Because YOUR SUCCESS is our MOTIVATION!

5 Total-System-Solution YASKAWA Academy 05 All training courses under one roof. Total System Solutions Against this background, YASKAWA presented an approach of Total System Solutions in the fall of 0. Modular combined products and software packages from the divisions Drives & Motion, Robotics and VIPA complemented each other thereby to achieve technically uniform solutions from a single source. Such a bandwidth from visualization including controlling to drive technology and robotics is unprecedented. The integration of automation and control technology in integrated system architectures receives special focus. Corresponding system solutions are available for automation tasks of all sizes. Technically unified automation solutions from one source offer advantages in planning, construction, commissioning, control and operation compared with conventional combinations. The prerequisite, however, is a broad and diversified portfolio that includes products and software of the visualization including control to drive technology and robotics. The YASKAWA Academy implements this requirement with the Total System Solutions concept. The YASKAWA Academy offers an extensive network of training institutions across Europe. In addition to training at locations in Germany, we can arrange globally for a place for you to study in almost all countries. Drives Frequency converter Medium voltage Complete System Solutions Servo Motion Controller TCS PLC Control HMI I/O Robots systems Robotics

6 06 YASKAWA Academy TCS Consultation Complete overhaul Installation Maintenance Our competence... Programming Spare Parts... all from a single source! Process Support Repair Cycle time optimization Training

7 TCS YASKAWA Academy 07 Total Customer Support is a mindset matter. In addition to Consultation, Installation, Programming, Process Support, Telephone Support, Spare Parts, Maintenance, Repair and Complete Overhaul Services, an important component of our capabilities is Training and Education. Here detailed knowledge as well as the big picture are just as important as the tips and tricks used in application-related programming. This principle is the goal of our training concept. Our recipe for success in training is the proper mix of well-explained theory and numerous practical exercises. In our training centers in Eschborn, Herzogenaurach and Allershausen, we use detailed training documentation as well as modern training means and methods. We offer you a diverse and comprehensive training course programme, which can enable and will qualify your staff from entry-level to experts for a variety of applications. You will be able to take full advantage of your YASKAWA MOTOMAN robots. Over two-thirds of the course time is used for practical exercises. Thus, your employees will gather all-round experience in the operation, programming and/or maintenance of robots and their respective application programs. For our international clients we can upon request coordinate training tailored to individual needs.

8 08 YASKAWA Academy Location Frankfurt YASKAWA Academy Eschborn Robotics The courses of the YASKAWA Academy in Eschborn near Frankfurt are presented using the latest technology and teaching methods. As European headquarters we set the highest standards for the quality of the execution and performance of our international training. Our courses are held routinely in English or German. Interpreters can be arranged for courses in other languages upon request. All training sessions are organised and coordinated at our headquarters in Eschborn. The proximity to the international Frankfurt Airport offers the advantage of being able to reach us quickly and easily worldwide. Our Training Centre in Eschborn has: n A 700 m² training area n 7 training rooms with the latest presentation technology n Over 50 robots of different controller generations n Almost all applications and various application examples n 6 technical trainers, training coordinators n A canteen

9 Location Frankfurt YASKAWA Academy 09 Trainer Overview YASKAWA Academy Eschborn YASKAWA Europe GmbH Robotics Division Hauptstraße 85 D Eschborn Tel. +49 (0) and +49 (0) Fax +49 (0) Torben Schäfer Manager Training Ina Krämer Training Coordinator Sabine Zarkovic Training Coordinator Harun Tahiri Technical Trainer Martin Fuchs Technical Trainer Jürgen Rother Technical Trainer Andreas Kähler Technical Trainer Horst Knoth Technical Trainer Arne Tiemer Technical Trainer

10 0 YASKAWA Academy Location Munich YASKAWA Academy Allershausen Robotics Especially for our customers from Switzerland, southern Germany and Austria, we offer training at the location of Allershausen and, subsequently, we create shorter journeys and move a bit closer to our customers. The close proximity to the Production, Repair and Development Department allows you to consult our experts or even to visit your facility during commissioning. In Allershausen we also teach in English and German. Interpreters can be arranged for courses in other languages upon request. Our YASKAWA Academy in Allershausen has: n A 80 m² training area n training rooms with the latest presentation technology n 6 robots in different applications and application examples n technical trainers n A canteen

11 Location Munich YASKAWA Academy Trainer Overview YASKAWA Academy Allershausen YASKAWA Europe GmbH Robotics Division Yaskawastraße D-859 Allershausen Tel. +49 (0) and +49 (0) Fax +49 (0) Roland Drehsen Training Leader Allershausen Thomas Purm Technical trainer

12 YASKAWA Academy Qualification Basic Training 4 days (. to 6.) Operator Training.5 days (. B to 6. B) Programming Training.5 days (. P to 6. P) Maintenance Training 0.5 days (0.W to 9.W) Upgrade Training day (. to 6.) Maintenance Diagnostic DX days (0. WD) Training for Lateral Entrants.5 days (. to 6.) Service Training Mechanics days (0.M to 5.M) Advanced Programming Training 4 days (.4 to 6.4) Service Training Electrical Equipment days (6.E to 0.E) Advanced Training for Lateral Entrants.5 days (.E to 6.E) Service Training Mechatronics.5 days (0.MT to 5.MT) Software Training varying duration (S. to 0.) Service Training Mechanics ATEX.5 days (ATEX.M) Safety Controller Training.5 days (.5 to 6.5) Advanced Training varying duration MotoSimEG days (S) MotoSim VRC days + days (S to S.5) System-Integrator Training 5 days (. to 6.) System Integrators Upgrade DX00 days (.U to 6.U) Advanced Programmer Expert Service technician Basic YASKAWA Academy. The road to qualification Robotics

13 Course Structure YASKAWA Academy The structure of our courses is your key to success. In addition to our standard courses we offer upon request customised training, in which we can cater for customer-specific requirements and equipment, and specialised functions. The possibility also exists upon request to conduct a variety of courses at customers facilities. Our Training Overview on the following pages will assist you in finding a suitable training course(s). For more information, events, and current training courses please look in the field of YASKAWA Academy under: A detailed description of all training courses can be obtained from the YASKAWA Academy. Our training programme offering is divided into the following five colour-coded areas: Programming Training Robotics Maintenance Training Robotics Software Training Robotics Training Drive Technology Training Control Technology Explanation of the tables on the following pages Training topic Application examples Training Course Code and Description Duration(Days) Number of participants (Min./Max.) Arc Welding & Cutting MIG MAG WIG TIG Plasma. Upgrade Training DX00-6 Previous knowledge is updated to the current controller generation and new functions are explained. 4 6 Target Group Prerequisites Basic training of the previous controller generation (MRC, XRC, NX00 or DX00)

14 4 YASKAWA Academy Programming Training Arc Welding & Cutting MIG MAG WIG TIG Plasma. BASIC TRAINING. B Operator Training.5-8 Safe and proper operation of a robot. Basic knowledge of robotics. P Programming Training.5-8 Program robot applications with standard instructions and customer-specific functions System operators, programmers, maintenance staff and System operators, programmers, maintenance staff and None Operator training. Upgrade Training DX00-6 Previous knowledge is updated to the current controller generation and new functions are explained 4.5 Safety Controller Training 6 DX 00 DX 00 Technical basics for proper operation with the safety controller MOTOMAN customers using a safety controller Basic training of the previous controller generation (MRC, XRC, NX00 or DX00) Profound knowledge of programming. Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots Shortly, the content of the basic training will be made known.6 Advanced Training Digital Power Sources Operation of already existing power sources, organisation in the weld controller, working with the weld software. -6 The training is done with manufacturers SKS, Fronius, EWM, ESAB and Kempi. Upon request additional manufacturers are possible. Experienced programmers and system operators Programming knowledge of other industrial robots Formation as welding engineer Upgrade, crossover or basic training.e Advanced Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots. Shortly, the content of the extended programming courses will be made known.7 Advanced Training Digital Power Sources -6 The calibration of analog weld power sources, defining and using the weld data and special welding functions Experienced programmers and system operators Crossover training.4 Advanced Programming Training 4-6 Programming robotic applications with advanced instructions and customized functions. Setting menus and robot-specific files are explained.8 Advanced Training Q-Set -6 Technical basics of Q-Set are explained. Setting up and calibration of the Q set. Using Q-Set and correcting JOBs. Programmers, machine setters, maintenance staff and Q-Set-experienced programmers

15 Programming Training YASKAWA Academy 5 Welding Cutting.9 Multirobot Training -6 Programming of robot systems with two or more robots or with dual-arm robots. Planners & Managers -8 Understanding operations, performances and limits of a robot system. Application possibilities and an optimized utilization of the plant and requirements for the personnel Project manager, division manager, planners and managers None.0 Multirobot Synchro Training -6 Programming of robot systems with two or more robots or with dual-arm robots.4 Advanced Training COMARC -6 Getting to know, using and applying weld seam tracking with the COMARC function Experienced programmers and system operators. Internal PLC & Field Bus Systems -5 Basics for integration of the robot into a manufacturing cell with focus on communication/integration with a host controller, tooling and safety technology. Configuration of field bus systems.5 Advanced Training Multilayer -6 Getting to know, using and applying multilayer welding. Importance of Euler angles. Experienced programmers and Advanced training COMARC PLC S7 Basic training.. System Integrators 5 Assembly, connection and installation of a robot system. Connection of external axes, carriageways, safety -5 installations and tools. Communication with a host controller, configuration of field bus systems.9 Advanced Training Search Function -4 Technical basics to use the search function properly. Fault diagnosis and troubleshooting. The aim of the search function is to find successfully System integrators Operators using the search function (Search) General knowledge of PLCs, electronics, mechanics. Experienced programmers and system operators.u System Integrators Upgrade DX00-6 Upgrade to DX00. Changes and new developments to bring the knowledge level for on the latest level..0 Advanced Training Sensor Systems -4 Technical basics to use sensor systems properly. Fault diagnosis and troubleshooting System integrators Operators using sensor systems System integrator training for earlier controller generations

16 6 YASKAWA Academy Programming Training Spot Welding Spot Welding Riveting. Basic Training. B Operator Training.5-8 Safe and proper operation of a robot. Basic knowledge of robotics. P Programming Training.5-8 Program robot applications with standard instructions and customer-specific functions System operators, programmers, maintenance staff and System operators, programmers, maintenance staff and None Operator training. Upgrade Training DX00-6 Previous knowledge is updated to the current controller generation and new functions are explained 4.5 Safety Controller Training 6 DX 00 DX 00 Technical basics for proper operation with the safety controller MOTOMAN customers using a safety controller Basic training of the previous controller generation (MRC, XRC, NX00 or DX00) Profound knowledge of programming. Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots Shortly. The content of the basic training will be made known shortly.6 Advanced Training Spot Welding -4 Application of MOTOMAN spot welding. Application and use for data with servo guns Experienced programmers and system operators Programming knowledge of other industrial robots.e Advanced Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots. Shortly. The content of the basic training will be made known shortly.9 Multirobot Training -6 Programming of robot systems with two or more robots or with dual-arm robots Crossover training.4 Advanced Programming Training 4-6 Programming robotic applications with advanced instructions and customized functions. Setting menus and robot-specific files are explained.0 Multirobot Synchro Training -6 Programming of robot systems with two or more robots or with dual-arm robots Programmers, machine setters, maintenance staff and

17 Programming Training YASKAWA Academy 7. Internal PLC & Field Bus Systems -5 Basics for integration of the robot into a manufacturing cell with focus on communication/integration with a host controller, tooling and safety technology. Configuration of field bus systems. Planners & Managers -8 Understanding operations, performances and limits of a robot system. Application possibilities and an optimized utilization of the plant and requirements for the personnel Experienced programmers and Project manager, division manager, planners and managers PLC S7 Basic training. None. System Integrators 5 Assembly, connection and installation of a robot system. Connection of external axes, carriageways, safety -5 installations and tools. Communication with a host controller, configuration of field bus systems.9 Advanced Training Search Function -4 Technical basics to use the search function properly. Fault diagnosis and troubleshooting. The aim of the search function is to find successfully System integrators Operators using the search function (Search) General knowledge of PLCs, electronics, mechanics. Experienced programmers and system operators.u System Integrators Upgrade DX00-6 Upgrade to DX00. Changes and new developments to bring the knowledge level for on the latest level. System integrators System integrator training for earlier controller generations Spot Welding Riveting

18 8 YASKAWA Academy Programming Training Painting & Dosing Painting Bonding Dosing Sealing. Basic Training. B Operator Training.5-8 Safe and proper operation of a robot. Basic knowledge of robotics. P Programming Training.5-8 Program robot applications with standard instructions and customer-specific functions System operators, programmers, maintenance staff and System operators, programmers, maintenance staff and None Operator training. Upgrade Training DX00-6 Previous knowledge is updated to the current controller generation and new functions are explained 4.5 Safety Controller Training 6 DX 00 DX 00 Technical basics for proper operation with the safety controller MOTOMAN customers using a safety controller Basic training of the previous controller generation (MRC, XRC, NX00 or DX00) Profound knowledge of programming. Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots Shortly, the content of the basic training will be made known.6 Advanced Training Painting -4 Application of special painting commands, use of painting data. Conveyor synchronized programming Experienced programmers and system operators Programming knowledge of other industrial robots.e Advanced Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots. Shortly. The content of the extended programming courses will be made known shortly.7 Advanced Training Vision Generally -6 Technical basics of camera systems. Application of the system, receive and convert data in the robot programme Experienced programmers and system operators Crossover training.4 Advanced Programming Training 4-6 Programming robotic applications with advanced instructions and customized functions. Setting menus and robot-specific files are explained.8 Advanced Training Vision YASKAWA -6 Technical basics of the YASKAWA camera system. Set up and calibrate the camera. Application of the system, receive and convert data in the robot programme Programmers, machine setters, maintenance staff and Experienced programmers

19 Programming Training YASKAWA Academy 9.9 Multirobot Training -6 Programming of robot systems with two or more robots or with dual-arm robots.u System Integrators Upgrade DX00-6 Upgrade to DX00. Changes and new developments to bring the knowledge level for on the latest level.on the latest level. System integrators System integrator training for earlier controller generations.0 Multirobot Synchro Training -6 Programming of robot systems with two or more robots or with dual-arm robots. Planners & Managers -8 Understanding operations, performances and limits of a robot system. Application possibilities and an optimized utilization of the plant and requirements for the personnel Project manager, division manager, planners and managers None. Internal PLC & Field Bus Systems -5 Basics for integration of the robot into a manufacturingcell with focus on communication/integration with a host controller, tooling and safety technology. Configuration of field bus systems.4 Advanced Training Conveyor -4 Technical basics of the Conveyor Function. Configure conveyor, synchronize motion. Start shift, overlimits and conveyor shift function Experienced programmers and Experienced programmers and system operators PLC S7 Basic training.. System Integrators 5 Assembly, connection and installation of a robot system. Connection of external axes, carriageways, safety -5 installations and tools. Communication with a host controller, configuration of field bus systems.9 Advanced Training Search Function -4 Technical basics to use the search function properly. Fault diagnosis and troubleshooting. The aim of the search function is to find successfully System integrators Operators using the search function (Search) General knowledge of PLCs, electronics, mechanics. Experienced programmers and system operators Painting Dosing Bonding Sealing

20 0 YASKAWA Academy Programming Training Machining Deburring Grinding Polishing Milling Engraving 4. Basic Training 4. B Operator Training.5-8 Safe and proper operation of a robot. Basic knowledge of robotics 4. P Programming Training.5-8 Program robot applications with standard instructions and customer-specific functions System operators, programmers, maintenance staff and System operators, programmers, maintenance staff and None Operator training 4. Upgrade Training DX00-6 Previous knowledge is updated to the current controller generation and new functions are explained Safety Controller Training 6 DX 00 DX 00 Technical basics for proper operation with the safety controller MOTOMAN customers using a safety controller Basic training of the previous controller generation (MRC, XRC, NX00 or DX00) Profound knowledge of programming 4. Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots Shortly. The content of the basic training will be made known shortly 4.6 Advanced Training Machining -8 Installing and working with an external TCP, the anticipation function, t-axis endless rotation or speed control Experienced programmers and system operators Programming knowledge of other industrial robots 4.E Advanced Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots. Shortly. The content of the basic training will be made known shortly 4.7 Advanced Training Vision Generally -6 Technical basics of camera systems. Application of the system, receive and convert data in the robot program Experienced programmers and system operators Crossover training 4.4 Advanced Programming Training 4-6 Programming robotic applications with advanced instructions and customized functions. Setting menus and robot-specific files are explained 4.8 Advanced Training Vision YASKAWA -6 Technical basics of the YASKAWA camera systems. Set up and calibrate the camera. Application of the system, receive and convert data in the robot program Programmers, machine setters, maintenance staff and Experienced programmers

21 Programming Training YASKAWA Academy 4.9 Multirobot Training -6 Programming of robot systems with two or more robots or with dual-arm robots 4.U System Integrators Upgrade DX00-6 Upgrade to DX00. Changes and new developments to bring the knowledge level for on the latest level.on the latest level. System integrators System integrator training for earlier controller generations 4.0 Multirobot Synchro Training -6 Programming of robot systems with two or more robots or with dual-arm robots 4. Planners & Managers -8 Understanding operations, performances and limits of a robot system. Application possibilities and an optimized utilization of the plant and requirements for the personnel Project manager, division manager, planners and managers None 4. Internal PLC & Field Bus Systems -5 Basics for integration of the robot into a manufacturingcell with focus on communication/integration with a host controller, tooling and safety technology. Configuration of field bus systems 4.4 Advanced Training Conveyor -4 Technical basics of the Conveyor Function. Configure conveyor, synchronize motion. Start shift, overlimits and conveyor shift function Experienced programmers and Experienced programmers and system operators PLC S7 Basic training. 4. System Integrators 5 Assembly, connection and installation of a robot system. Connection of external axes, carriageways, safety -5 installations and tools. Communication with a host controller, configuration of field bus systems 4.9 Advanced Training Search Function -4 Technical basics to use the search function properly. Fault diagnosis and troubleshooting. The aim of the search function is to find successfully System integrators Operators using the search function (Search) General knowledge of PLCs, electronics, mechanics. Experienced programmers and system operators Milling Grinding Engraving

22 YASKAWA Academy Programming Training Handling Assembly Machine Operator Loading and Unloading 5. Basic Training 5. B Operator Training.5-8 Safe and proper operation of a robot. Basic knowledge of robotics 5. P Programming Training.5-8 Program robot applications with standard instructions and customer-specific functions System operators, programmers, maintenance staff and System operators, programmers, maintenance staff and None Operator training 5. Upgrade Training DX00-6 Previous knowledge is updated to the current controller generation and new functions are explained Safety Controller Training 6 DX 00 DX 00 Technical basics for proper operation with the safety controller MOTOMAN customers using a safety controller Basic training of the previous controller generation (MRC, XRC, NX00 or DX00) Profound knowledge of programming 5. Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots Shortly, the content of the basic training will be made known 5.6 Advanced Training Handling -8 Programming advanced instructions, customized and application-related functions with robot applications. Special focus on general handling. Experienced programmers and system operators Programming knowledge of other industrial robots 5.E Advanced Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots. Shortly, the content of the extended programming courses will be made known 5.7 Advanced Training Vision Generally -6 Technical basics of camera systems. Application of the system, receive and convert data in the robot program Experienced programmers and system operators Crossover training 5.4 Advanced Programming Training 4-6 Programming robotic applications with advanced instructions and customized functions. Setting menus and robot-specific files are explained 5.8 Advanced Training Vision YASKAWA -6 Technical basics of the YASKAWA camera systems. Set up and calibrate the camera. Application of the system, receive and convert data in the robot program Programmers, machine setters, maintenance staff and Experienced programmers

23 Programming Training YASKAWA Academy Handling 5.9 Multirobot Training -6 Programming of robot systems with two or more robots or with dual-arm robots 5.U System Integrators Upgrade DX00-6 Upgrade to DX00. Changes and new developments to bring the knowledge level for on the latest level. System integrators System integrator training for earlier controller generations 5.0 Multirobot Synchro Training -6 Programming of robot systems with two or more robots or with dual-arm robots 5. Planners & Managers -8 Understanding operations, performances and limits of a robot system. Application possibilities and an optimized utilization of the plant and requirements for the personnel Project manager, division manager, planners and managers None 5. Internal PLC & Field Bus Systems -5 Basics for integration of the robot into a manufacturingcell with focus on communication/integration with a host controller, tooling and safety technology. Configuration of field bus systems 5.4 Advanced Training Conveyor -4 Technical basics of the Conveyor Function. Configure conveyor, synchronize motion. Start shift, overlimits and conveyor shift function Experienced programmers and Experienced programmers and system operators PLC S7 Basic training. 5. System Integrators 5 Assembly, connection and installation of a robot system. Connection of external axes, carriageways, safety -5 installations and tools. Communication with a host controller, configuration of field bus systems 5.5 Advanced Training MotoPal operator -4 Technical basics to use MotoPal properly. Fault diagnosis and troubleshooting System integrators Application with MotoPal General knowledge of PLCs, electronics, mechanics.

24 4 YASKAWA Academy Programming Training Handling Assembly Machine Operator Loading and Unloading 5.6 Advanced Training MotoPal Setter -4 Technical basics to set up MotoPal properly. Fault diagnosis and troubleshooting 5.9 Advanced Training Search Function -4 Technical basics to use the search function properly. Fault diagnosis and troubleshooting. The aim of the search function is to find successfully Application with MotoPal, Operators using the search function (Search) MotoPal operator Experienced programmers and system operators 5.7 Advanced Training MotoPick Operator -4 Technical basics to use MotoPick properly. Fault diagnosis and troubleshooting 5.0 Advanced Training Sensor Systems -4 Technical basics to use sensor systems properly. Fault diagnosis and troubleshooting Application with MotoPick Operators using sensor systems 5.8 Advanced Training MotoPick Setter -4 Technical basics to set up MotoPick properly. Fault diagnosis and troubleshooting Application with MotoPick MotoPick operator

25 Programming Training YASKAWA Academy 5 Picking, Packing, Palletising 6. Basic training 6. B Operator Training.5-8 Safe and proper operation of a robot. Basic knowledge of robotics 6. P Programming Training.5-8 Program robot applications with standard instructions and customer-specific functions System operators, programmers, maintenance staff and System operators, programmers, maintenance staff and None Operator training 6. Upgrade Training DX00-6 Previous knowledge is updated to the current controller generation and new functions are explained Safety Controller Training 6 DX 00 DX 00 Technical basics for proper operation with the safety controller MOTOMAN customers using a safety controller Basic training of the previous controller generation (MRC, XRC, NX00 or DX00) Profound knowledge of programming 6. Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots Shortly, the content of the basic training will be made known 6.6 Advanced Training Picking, Packing, Palletising -8 Programming advanced instructions, customized and application-related functions with robot applications. Special focus on pick and place applications and position calculations Experienced programmers Programming knowledge of other industrial robots 6.E Advanced Crossover Training.5-6 Application of the knowledge of and experience with other industrial robots to MOTOMAN robots. Shortly, the content of the extended programming courses will be made known 6.7 Advanced Training Vision Generally -6 Technical basics of camera systems. Application of the system, receive and convert data in the robot program Experienced programmers and system operators Crossover training 6.4 Advanced Programming Training 4-6 Programming robotic applications with advanced instructions and customized functions. Setting menus and robot-specific files are explained 6.8 Advanced Training Vision YASKAWA -6 Technical basics of the YASKAWA camera systems. Set up and calibrate the camera. Application of the system, receive and convert data in the robot program Programmers, machine setters, maintenance staff and Experienced programmers

26 6 YASKAWA Academy Programming Training Picking, Packing, Palletising 6.9 Multirobot Training -6 Programming of robot systems with two or more robots or with dual-arm robots 6. Planners & Managers -8 Understanding operations, performances and limits of a robot system. Application possibilities and an optimized utilization of the plant and requirements for the personnel Project manager, division manager, planners and managers None 6.0 Multirobot Synchro Training -6 Programming of robot systems with two or more robots or with dual-arm robots 6.4 Advanced Training Conveyor -4 Technical basics of the Conveyor Function. Configure conveyor, synchronize motion. Start shift, overlimits and conveyor shift function Experienced programmers and system operators 6. Internal PLC & Field Bus Systems Basics for integration of the robot into a manufacturingcell with focus on communication/integration with a host -5 controller, tooling and safety technology. Configuration of field bus systems 6.5 Advanced Training MotoPal Operator -4 Technical basics to use MotoPal properly. Fault diagnosis and troubleshooting Experienced programmers and Application with MotoPal PLC S7 Basic Training. Upgrade, crossover or basic Training 6. System Integrators 5 Assembly, connection and installation of a robot system. Connection of external axes, carriageways, safety -5 installations and tools. Communication with a host controller, configuration of field bus systems 6.6 Advanced training MotoPal Setter -4 Technical basics to set up MotoPal properly. Fault diagnosis and troubleshooting System integrators Application with MotoPal, General knowledge of PLCs, electronics, mechanics. MotoPal operator 6.U System Integrators Upgrade DX00-6 Upgrade to DX00. Changes and new developments to bring the knowledge level for on the latest level 6.7 Advanced Training MotoPick Operator -4 Technical basics to use MotoPick properly. Fault diagnosis and troubleshooting System integrators Application with MotoPick System integrator training for earlier controller generations

27 Programming Training YASKAWA Academy Advanced Training MotoPick Setter -4 Technical basics to set up MotoPick properly. Fault diagnosis and troubleshooting 6.0 Advanced Training Sensor Systems -4 Technical basics to use sensor systems properly. Fault diagnosis and troubleshooting Application with MotoPick Operators using sensor systems MotoPick operator 6.9 Advanced Training Search Function -4 Technical basics to use the search function properly. Fault diagnosis and troubleshooting. The aim of the search function is to find successfully Operators using the search function (Search) Experienced programmers and system operators Welding MotoWeld RL50 MW- RL50. Operator Training MotoWeld RL50 Knowing and understanding the basic functions and settings of the power source. Organisation in the weld controller. Management via the DX00 Basic training. Welding

28 8 YASKAWA Academy Service Training Picking Robot MPK MPK5 MYS-series MPP 0.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training 0.M Service Training Mechanical Equipment -4 Technical basics for proper mechanical mending work for each robot category. Basics for successful fault diagnosis and troubleshooting 0. MT Service Training Mechatronics 0.M-XRC 0.M-NX00 0.M-DX00 0.M-FS00 0.M-DX00.5 Technical basics for proper mechanical and electrical mending work for each robot category. Fault diagnosis -4 and troubleshooting Maintenance technicians mechanic Maintenance technicians, mechanic and electrics Operator and maintenance training Operator and maintenance training Robot > 5 kg MH5F MH5S MH5L MH5 HP HPL and previous models since XRC.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training.m Service Training Mechanical Equipment -4 Technical basics for proper mechanical mending work for each robot category. Basics for successful fault diagnosis and troubleshooting. MT Service Training Mechatronics 0.M-XRC 0.M-NX00 0.M-DX00 0.M-FS00 0.M-DX00.5 Technical basics for proper mechanical and electrical mending work for each robot category. Fault diagnosis -4 and troubleshooting Maintenance technicians mechanic Maintenance technicians, mechanic and electrics Operator and maintenance training Operator and maintenance training

29 Service Training YASKAWA Academy 9 Robot 6 0 kg MH6 till MH4 HP0D MH50-0 MA400 till MA00 and previous models since XRC.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training.m Service Training Mechanical Equipment -4 Technical basics for proper mechanical mending work for each robot category. Basics for successful fault diagnosis and troubleshooting. MT Service Training Mechatronics 0.M-XRC 0.M-NX00 0.M-DX00 0.M-FS00 0.M-DX00.5 Technical basics for proper mechanical and electrical mending work for each robot category. Fault diagnosis -4 and troubleshooting Maintenance technicians mechanic Maintenance technicians, mechanic and electrics Operator and maintenance training Operator and maintenance training Robot kg MH50-5 MH50II MS80II ES65 till ES80D UP50D till UP50-600D MPL80 MH0 till MH600.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training.m Service Training Mechanical Equipment -4 Technical basics for proper mechanical mending work for each robot category. Basics for successful fault diagnosis and troubleshooting. MT Service Training Mechatronics 0.M-XRC 0.M-NX00 0.M-DX00 0.M-FS00 0.M-DX00.5 Technical basics for proper mechanical and electrical mending work for each robot category. Fault diagnosis -4 and troubleshooting Maintenance technicians mechanic Maintenance technicians, mechanic and electrics Operator and maintenance training Operator and maintenance training

30 0 YASKAWA Academy Service Training Palettising robots MPK50 MPL00 till MPL800 4.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training 4.M Service Training Mechanical Equipment -4 Technical basics for proper mechanical mending work for each robot category. Basics for successful fault diagnosis and troubleshooting 4. MT Service Training Mechatronics 0.M-XRC 0.M-NX00 0.M-DX00 0.M-FS00 0.M-DX00.5 Technical basics for proper mechanical and electrical mending work for each robot category. Fault diagnosis -4 and troubleshooting Maintenance technicians mechanic Maintenance technicians, mechanic and electrics Operator and maintenance training Operator and maintenance training 7 and 5 axis robots SIA0 SIA0 SIA50D 50 SDA0 SDA0 5.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training 5.M Service training Mechanical Equipment -4 Technical basics for proper mechanical mending work for each robot category. Basics for successful fault diagnosis and troubleshooting 5. MT Service training Mechatronics 0.M-XRC 0.M-NX00 0.M-DX00 0.M-FS00 0.M-DX00.5 Technical basics for proper mechanical and electrical mending work for each robot category. Fault diagnosis -4 and troubleshooting Maintenance technicians mechanic Maintenance technicians, mechanic and electrics Operator and maintenance training Operator and maintenance training

31 Service Training YASKAWA Academy Painting robots EPX50 EPX050 EPX 700 EPX 800R EPX800 EPX900 ATEX.W 0.5 Maintenance Training Technical basics for proper maintenance work Maintenance personnel and system operators Operator training ATEX.M.5-4 Service Training Mechanical Equipment Technical basics for proper mechanical mending work for each robot category. Basics for successful fault diagnosis and troubleshooting ATEX.MT Service Training Mechatronics ATEX.M-XRC ATEX.M-NX00 Technical basics for proper mechanical and electrical mending work for each robot category. ATEX-instructions. -4 Fault diagnosis and troubleshooting Maintenance technicians mechanic Maintenance technicians, mechanic and electrics Operator and maintenance training Operator and maintenance training XRC 6.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training 6.E Service training Electrical Equipment -8 Technical basics for proper electrical mending work for each control generation. Basics for successful fault diagnosis and troubleshooting Maintenance technicians electric Operator and maintenance training

32 YASKAWA Academy Service Training NX00 7.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training 7.E Service Training Electrical Equipment -8 Technical basics for proper electrical mending work for each control generation. Basics for successful fault diagnosis and troubleshooting Maintenance technicians electric Operator and maintenance training DX00 8.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training 8.E Service Training Electrical Equipment -8 Technical basics for proper electrical mending work for each control generation. Basics for successful fault diagnosis and troubleshooting Maintenance technicians electric Operator and maintenance training

33 Service Training YASKAWA Academy FS00 9.W Maintenance Training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training 9.E Service Training Electrical Equipment -8 Technical basics for proper electrical mending work for each control generation. Basics for successful fault diagnosis and troubleshooting Maintenance technicians electric Operator and maintenance training DX00 0.W Maintenance training 0.5 Technical basics for proper maintenance work Maintenance personnel and system operators Operator training 0. WD Maintenance Diagnostic DX Technical basics for proper maintenance diagnostic of DX00 0.E Service Training Electrical Equipment -8 Technical basics for proper electrical mending work for each control generation. Basics for successful fault diagnosis and troubleshooting Maintenance personnel and system operators Maintenance technicians electric Operator and maintenance training Operator and maintenance training

34 4 YASKAWA Academy Software Training FDDWin 0.5 S FDDWin Training Function and application of the backup software FDDWIN Upgrade training to the next Controller generation, crossover or basic training, PC and English knowledge FDDWin FTP Function S FTP Training Function and application of the FTP option Upgrade training to the next Controller generation, crossover or basic training, PC and English knowledge JobEditor 0.5 S JobEditor Training Function and application of the software JobEditor FTP-Funktion JobEditor Basic training, PC experience and English knowledge JobExchanger 0.5 LadderEditor S4 S5 JobExchanger Training Function and application of the software JobExchanger Basic training, PC experience and English knowledge LadderEditor Training Function and application of the software LadderEditor Basic training, MOTOMAN PLC training, PC experience and English knowledge JobExchanger Ladder Editor

35 Software Training YASKAWA Academy 5 MotoAdmin S6 MotoAdmin Training (Tool forremote Access) Function and application of the software MotoAdmin MotoAdmin Basic training, PC experience and English knowledge MotoCalvEG S7 MotoCalvEG Training 0.5 Function and application of the software MotoCalvEG Basic training, PC experience and English knowledge MotoCom S8 Motocom Training Function and application of MotoCom MotoCalvEG MotoCom Basic training, Windows programmers- and English knowledge MotoDCI S9 MotoDCI Training 0.5 Function and application of MotoDCI MotoDCI Basic training, PC experience and English knowledge MotoOPCServer S0 MotoOPCServer Training Function and application of the MotoOPC Server. Basic training, PC experience and English knowledge OPC MotoOPCServer

36 6 YASKAWA Academy Software Training MotoGSI S MotoGSI Training 4 Function and application of MotoGSI -6 MotoGSI Experienced programmers of DX00 or FS00. Network knowledge MotoSimEG S -6 Basic Training MotoSimEG Basics of MotoSimEG. Integrate models, cells and simple robot programs Experienced programmers, plant operators,, work preparation MotoSIM Basic training, PC experience and English knowledge MotoSimVRC S -6 Basic Training MotoSimVRC Basics of MotoSimVRC. Integrate models, cells and simple robot programs Experienced programmers, plant operators,, work preparation MotoVRC Basic training, PC experience and English knowledge S. Module : External and Basic Axes -6 Advanced training to create external axes and basic axes and their integration, configuration and programming Experienced programmers, plant operators,, work preparation Basic training MotoVRC, good PC experience, English knowledge MotoVRC S. Module : Conveyor -6 Advanced training to create conveyors and their integration, configuration and programming Experienced programmers, plant operators,, work preparation Basic training MotoVRC, good PC experience, English knowledge MotoVRC

37 Software Training YASKAWA Academy 7 S. Module : Twin Cells / Multirobot -6 Advanced training to create multirobot cells ( or more robots) and their integration, configuration and programming Experienced programmers, plant operators,, work preparation Basic training MotoVRC, Multirobot-Synchron-Training, good PC experience, English knowledge MotoVRC S.4 Module 4: Offline Programming.5-6 Extension training on the correct implementation and application of off-line programming. Matching virtual and real robot systems Experienced programmers, plant operators,, work preparation Basic training MotoVRC, good PC experience, English knowledge MotoVRC S.5 Module 5: Open Training Using a Practical Example Independent creation of a robot cell from our training facility using all previously acquired content. Objective of this exercise is to create a real -6 robot cell Experienced programmers, plant operators,, work preparation MotoVRC Basic training MotoVRC, good PC experience, English knowledge MotoPlus S4 a.a. -4 MotoPlus Training Basics and application of MotoPlus. PP customization, Customizing the PHG interface with individual applications Experienced programmers and Experienced programmers of DX00 or FS00. Network knowledge. Very good knowledge of Visual, C or C++ MotomanSync S5.5-4 MotomanSync Training Basics and application of MotomanSync. Activation and programming of the robot via a PLC Experienced programmers and Experienced programmers of DX00 or FS00. Network knowledge. Very good knowledge of SIMATIC S7 MotoPLUS MOTOMAN Sync

38 8 YASKAWA Academy Certification YASKAWA Certification programme Robotics The use of the YASKAWA industrial robot is progressing quite well in all industrial branches and applications. Accordingly, the technology has evolved in its variety of possibilities and options. The YASKAWA certification programme stays abreast of this development, by qualifying programmers and maintenance staff and to build up the necessary expertise. By qualifying your employees, you are able to independently implement problem solutions professionally and expertly. Upon successful completion of the appropriate training for BACHELOR or MASTER, this qualification degree is certified with a certificate. Accurate information to the Bachelor and Master courses can be obtained from employees of YASKAWA Academy. System Setup Training Z System Setup Training Overview of the organization and the product range of YASKAWA. Overview of all functions of the robot controller. Expanding the main configurations of the robot controllers, initialization, parameter settings, robotic systems to facilitate more robots, external axes and roadways System integrators and participants of the training courses to Bachelor and Master, PC experience and English knowledge Bachelor Examination ZYB-M Bachelor Examination 0.5 Theoretical and practical verification of levels of understanding and knowledge of previous training modules Graduates of Bachelor's degree courses All training modules of the Bachelor course series Master Examination ZYM-M Master Examination Theoretical and practical verification of levels of understanding and knowledge of previous training modules Emphasis is complex technical system configurations and the resolving of problems Graduates of Master's degree courses Successful Bachelor examination and all training modules of the Master s degree programme

39 Open Training YASKAWA Academy 9 Open Training The freedom to work intensively on your own. You, as a user would like to... n practise on a YASKAWA MOTOMAN robot without interrupting production of your plant. n strengthen and deepen the knowledge and skills acquired in a training course with further practical exercises. n refresh and deepen your knowledge and skills you obtained in one of our training courses that you attended some time ago. n test and try functions and applications for which you do not have the opportunity in your company due to the absence of available robots. Course Purpose and Content We offer you the opportunity to use a YASKAWA MOTOMAN robot independently for your tasks and exercises. Industrial robots of controller generations MRC, XRC, NX00, NXC00 DX00, FS00 and DX00 are available for your open and independent training. With respect to the availability of specific robot types and their respective applications, please contact the YASKAWA Academy. For your support, a trainer of the YASKAWA Academy will be assigned to you to help you with problems and to answer your questions. Minimum Prerequisite: Operator training Bring along: Your training documentation from previous training course(s) Extensive training programme in a professional environment The YASKAWA Academy offers a highly differentiated and extensive range of training courses for the widest range of interests and skill levels. The equipment is technically very modern and geared towards a positive learning atmosphere. The high proportion of practical teaching content and exercises on the robot convey the acquired knowledge with an excellent connection to real application in place. We are pleased that our SUMO automation system Flexiplex contributes further to the intensification of the practical experience aspect. Heiko Röhrig Head of sales and marketing EGS Automatisierungstechnik GmbH

40 40 YASKAWA Academy Training on Location Something very special. At regular intervals we offer special trainings, events and workshops. On our home page you will find current information. Should you wish special training, we will create an individualised training plan just for you in accordance with your needs and requirements. At our place or yours? Are there reasons why you prefer training at home? Then we gladly come to you on location of your factory. Our offer is world-wide; we offer the possibility that our experienced trainers train and teach your employees in their familiar environment. We will advise you on the possibilities and together with you weigh up the advantages and possible disadvantages. Should the training-technical equipment not be available on location of your facility, we will bring everything along. Should the required number of training robots not be available, you have the additional option to book our mobile training robot Training in motion. Contact the staff of our YASKAWA Academy for more details.

41 Mobile Cell YASKAWA Academy 4 Training in motion Our Mobile Training Cell. To participate in training sessions outside the YASKAWA Academy, we conceptualized this training cell with the same quality. It is important to us, that, taking into consideration the safety procedures, a less complicated and faster assembly at the construction site is accomplished. The training cell is easy to move, fits through normal door width and can thus be used in almost every classroom. Apart from electricity, no other media are needed, since the gripper system consists of magnetic grippers. The controls are integrated and meet our training standards. All necessary consumables, such as tools and equipment will be supplied. You will be surprised to see how quickly you can perform the first movements of the robot after delivery. For details on shipping and scheduling availability, please inquire at the YASKAWA Academy. The trend towards flexible manufacturing, i.e. handling of robots, has grown into a decisive economic factor. Apart from purely technical problems, particularly elements of ecology have led to new insights. Subsequently, it is not the goal of automation any more to completely replace humans by technology, but rather to teach employees new skills and competences. WIFI OÖ as early as already 988 grappled with this task and started with seminars in the field of robotics. Today, the WIFI in Linz is just one of many certified training centres for YASKAWA. We're always keen on behalf of our customers to keep the technical equipment on the latest level. WIFI-students thus enrol to acquire future-oriented competences and qualifications for YASKAWA robot technologies. Doz. Ing. Dipl.-Wirt.-Ing. Gerhard Michlbauer EUR Ing. WIFI OÖ GmbH Head of Robot Competence Centre

42 4 YASKAWA Academy Location Frankfurt YASKAWA Academy Eschborn Drive technology The courses in the field of drive technology are presented, as is the case in the area of robotics, based on state of the art technical and didactic methods. Application engineers with additional training in the field of technical teaching perform training in their areas of speciality. You, therefore, benefit from a high degree of experience and expertise to meet your needs. As usual, the courses take place in German and English. At our European headquarters in Eschborn, we offer: n Training by application engineers n Classrooms with the latest presentation technology n Various training demo s and application examples n Overview of all products n A pleasant training atmosphere n A canteen

43 Location Frankfurt YASKAWA Academy 4 Trainer Overview Drives&Motion YASKAWA Academy Eschborn YASKAWA Europe GmbH Robotics Division Hauptstraße 85 D Eschborn Tel. +49 (0) and +49 (0) Fax +49 (0) Manfred Mollner Technical Trainer Brett Pawielski Technical Trainer Bernd Wittayer Technical Trainer Roberto Adanez Technical Trainer Daniel Mendt Technical Trainer Sascha Göbel Technical Trainer Stephan Hensel Technical Trainer Frequency converter Klaus Unger Technical Trainer Julian Schulte Technical Trainer Jörg Schmidt Technical Trainer Mustafa Yildirim Technical Trainer Motion Controller SERVO

44 44 YASKAWA Academy Drives & Motion Frequency Converter (Drives) D Basic Training Inverter D6 Maintenance Training Inverter Understanding the basics and applications of the frequency converter. Product overview Design of the inverter. Replacing maintenance parts. Parameter backup. Trouble shooting Plant and machine builders System integrators Maintenance staff Technical understanding Electronic basics D Product Training Inverter D7 Application Training Inverter Being able to make the right selection of products and the appropriate options Standard commissioning Design of the inverter. Configure the required parameters. Connection and wiring. DriveWizardPlus Plant and machine builders System integrators Plant and machine builders System integrators Technical understanding Electronic basics D Technical Training Inverter Commissioning and independent creation of complex configurations. Optimization of the drive functions Plant and machine builders System integrators commissioning Product training Inverter D4 DriveWorksEZ Pro Training Function and application of the software for graphical project planning of functional extensions. DriveWorksEZ Pro Plant and machine builders System integrators Technical training Inverter D5 Customer-Specific Training upon request a.a. 4-7 Customer training in accordance with agreement and customer requirements Plant and machine builders System integrators Technical training Inverter

45 Drives & Motion YASKAWA Academy 45 Machine Control (Motion Controller IEC) C Product Training C Advanced Technical Training Understanding the basics and application fields of the IEC machine control. Being able to make the right selection of products and the appropriate options Commissioning and independent creation of more complex programmes and optimization of IEC machine controllers. Obtain in-depth knowledge. Parametrization and optimization of servo drives in connection with IEC machine controls Facility and machine builders System integrators Facility and machine builders System integrators Technical understanding Product training, technical basic training C Training of Technical Basics C4 Machine Control Complete Training Commissioning and independent creation of simple programmes and optimization of IEC machine controllers. 5 Commissioning and independent creating of programmes with the MPiec machine control system. Commissioning and optimization of servo-drives in conjunction with the MPiec machine control system Plant and machine builders System integrators Plant and machine builders System integrators Product training Product training Servo-Drive Technology (Servo) SV Basic Training Servo SV Technical Training Servo 0.5 Understanding the basics of the technology and application areas of servo drives. Product overview Commissioning and independent creation of complex configurations of servo drives. Facility and machine builders System integrators Facility and machine builders System integrators Technical understanding Basic training Servo Product training Servo SV Product Training Servo Being able to make the right choice of servo products Plant and machine builders System integrators Basic training

46 46 YASKAWA Academy VIPA Herzogenaurach YASKAWA Academy Herzogenaurach Control technology (VIPA) Due to the central geographical position, the way to innovative training to almost all points in Germany is easily accessible. The close proximity to the Production, Repair and Development Department allows you to consult our experts or even to visit your facility during commissioning. In Herzogenaurach, Germany, we also teach in German and English. Our VIPA academy in Herzogenaurach has: n A 50 m² training area n 4 training rooms with the latest presentation technology n 5 technical trainers n A canteen

47 VIPA Herzogenaurach YASKAWA Academy 47 Trainer Overview YASKAWA Academy Herzogenaurach VIPA GmbH Ohmstraße 4 D-9074 Herzogenaurach Tel. +49 (0) Fax +49 (0) Fritz Dotzer Technical trainer Andreas Höhn Technical trainer Torsten Zerl Technical trainer Kai Sommer Technical trainer Helmut Poeloth Technical trainer

48 48 YASKAWA Academy VIPA SIMATIC S7 PLC Basic Training SIMATIC S7 PLC Service Training SIMATIC S7 Basics of PLC in application of SIMATIC S7 4 Learning skills to locate and fix errors in the systems and programmes. Use of the diagnostic possibilities for systematic troubleshooting None SIMATIC S7 basic training or comparable basic knowledge PLC Advanced Training SIMATIC S7 PLC4 Communication SIMATIC S7 4 Extension of knowledge on troubleshooting, commissioning and visualisation in more complex PLC programmes for SIMATIC-S7 controllers Learning skills for configuration, troubleshooting and testing of different bus systems such as MPI, PROFIBUS, PROFINET and industrial ethernet SIMATIC S7 basic training or comparable basic knowledge SIMATIC S7 basic training or comparable basic knowledge MOVICON VMB VIPA MOVICON Basic VMA VIPA MOVICON Advanced HMI product presentation and functions. Basics of Scada software Movicon Advanced applications and programming of the Scada software Movicon None VIPA MOVICON Basic

49 VIPA YASKAWA Academy 49 Teleservice VTB VIPA Teleservice Basic VTA VIPA Teleservice ADVANCED Product presentation, operational applications, fundamentals/teleservice prerequisites, basic device functions. Basic project planning TM-C/H Advanced application possibilities and device functions, examples of script programming, create your own, simple web pages None VIPA Teleservice Basic Simatic S7/DriveWizzard VYB VIPA meets Yaskawa Basic Combination of VIPA and YASKAWA components. Project planning and application possibilities. Examples with MODBUS RTU/PROFIBUS/PROFINET Programmers, maintenance staff and Simatic S7 basic knowledge and drive technology

50 WINNING TEAM The new DX00 controller with new MOTOMAN robots by the inventor of the Mechatronics Successful teams work together perfectly, leverage the strengths of each other and use the right tool skilfully. So, new MOTOMAN robots were created at YASKAWA and the new DX00 controller, which helps your facility to achieve new top performances. Both the integrated safety controller, as well as application-specific function packages that are easy to program will in combination with newly designed robots pave the way for numerous stage and overall victories.

51 Registration YASKAWA Europe GmbH Robotics Division YASKAWA Academy Hauptstraße 85 D Eschborn/Ts. Tel. +49 (0) und -80 Fax +49 (0) Sender: Company Contact Street/No. Department Please indicate your desired training location: Eschborn/Frankfurt on the Main Allershausen/Munich Herzogenaurach (VIPA) Postal code / City Tel. Fax New customer: Yes / No If No, please enter your customer number: Value added tax identification number Invoicing address if different from sender Company Please enter your order number, if your training has already been purchased in another order (e.g. robot order): Street/No. Postal code / City Registration for the following training course(s) Controller: MRC XRC NX00 DX00 FS00 DX00 Others Drive technology (Drives & Motion): Controll technology (VIPA): Training Course Code Application Duration/Days Costs in Registration of your staff for the desired time period First Name Last Name Date/Calendar Week I have read the General Standard Terms and Conditions of the YASKAWA Europe GmbH and agree to them. I hereby accept your offer. Place, Date Stamp/Signature

52 5 YASKAWA Academy Organisation General Terms and Conditions for Training Courses Registration Registration and deregistration will only be made at the following address: YASKAWA Europe GmbH Robotics Division YASKAWA Academy Frankfurt Hauptstraße 85 D Eschborn/Ts. Tel. +49 (0) Tel. +49 (0) Fax +49 (0) Dates The course dates will be communicated upon request. Please contact us well in advance so that the dates you have requested can be taken into consideration. Courses can only be reserved after submission of the completed registration form. YASKAWA Academy reserves the right to reschedule the courses offered if the number of participants is too low or for other special reasons if necessary, also after confirmation of course registration. Accommodation Due to the wide range of hotels available as well as individual preferences and company guidelines, we cannot make hotel reservations for Frankfurt and Allershausen. We appreciate your kind understanding. For courses during trade fairs, please make your hotel reservations well in advance as the hotels are booked out quickly. Cancellations After YASKAWA Academy confirms the registration, requests for cancellation will only be accepted in writing. The processing fee for cancellation up to 4 days prior to commencement of the course is 0% of the course fee. The processing fee for cancellation up to 7 days prior to commencement of the course is 50% of the course fee. After this period or if the participant does not attend the course, the full course fee will be charged. Should a registered participant be unable to attend the course, he/she may name a different participant as substitute. Completion Upon successful completion of a course, participants receive a certificate indicating the topics covered during the course. A confirmation of participation is given to participants who have not been able to follow the course content due to insufficient previous knowledge or communication problems. Times Training Schedule The YASKAWA Academy is open on training days from 8.00 to 7.00 hours. For the exact course times, refer to your order confirmation, as these can vary depending on the booked course. Training material All course documents will only be handed out during the training course. Manuals cannot be sent to prospective participants in advance. Catering Refreshments and lunch on training days are included in the course fees. Liability At our premises YASKAWA Europe GmbH is not liable for damage caused due to accidents at our plant or due to loss of personal property. Furthermore, we are not liable for damage caused by the customer at his or her facility when applying the knowledge imparted in the training course. At your premises (on-site) We strongly recommend that the training of your personnel takes place at our Training Centre(s). It is our experience that a training session is more effective and of a higher quality when the training takes place at one of our training centres rather than in your facility due to the fact that our training personnel is better able to address the individual needs of the participants. In addition, distractions of day-to-day business are avoided. In addition, please be aware that a maximum of participants can be trained simultaneously on a single piece of equipment. Furthermore, there is a risk to the operational safety of your equipment due to operator/ programming errors made by the participants during the training. Please be aware that YASKAWA Europe GmbH does not in any way accept any responsibility or liability for damage incurred during or as a result of the training nor their resulting costs.

53 How to find us YASKAWA Academy 5 Here is how you can find our Trainings Centres L04 Berlinerstr. Hauptstraße YASKAWA Europe Firmenzentrale Schulungzentrum Frankfurt A5 Richtung Kassel Schwalbacher Str. L005 Hauptstraße Berlinerstr. Hauptstraße Hauptstraße L006 L005 Nordwestkreuz Frankfurt A66 Oberursel Schulungszentrum Frankfurt Bad Homburg A5 Richtung Kassel Bad Homburg Kreuz Lorscher Straße A66 Richtung Köln/Wiesbaden Eschborner Dreieck A648 Wiesbadener Straße Frankfurt am Main Bad Soden L005 Eschborner Dreieck Nord-West Kreuz A66 A648 A5 Westkreuz Frankfurt A66 Frankfurt Offenbach A5 YASKAWA Europe GmbH Robotics Division Eschborn near Frankfurt Hauptstraße 85 D Eschborn/Taunus Tel. +49 (0) and +49 (0) Fax +49 (0) Richtung Köln/Wiesbaden A Flughafen Frankfurt Frankfurter Kreuz Richtung Karlsruhe/Basel A Richtung Würzburg Ausfahrt Allershausen Zentrale Allershausen Freising A9 Richtung Nürnberg Richtung Deggendorf Mühlenstraße A9 Richtung Nürnberg A9 Flughafen MUC Kammerfeldstr. Firmenzentrale Fertigung Kesselbodenstraße Münchner Straße Albert-Schweizer-Str. Münchner Straße Dachau A9 Kreuz Neufahrn A9 Schroßlacher Straße YASKAWA MOTOMAN Robotics Division Firmenzentrale Schulungszentrum A8 Richtung Stuttgart A99 Ismaning Yaskawastraße A9 Richtung München Mittlerer Ring YASKAWA Europe GmbH Robotics Division Allershausen near Munich Yaskawastraße D-859 Allershausen Tel. +49 (0) and +49 (0) Fax +49 (0) A96 Richtung Lindau A99 München A94 A99 A94 A8 A95 A995 Richtung Starnberg Richtung Garmisch- Partenkirchen A8 Richtung Salzburg

54 54 YASKAWA Academy How to find us Here is how you can find our Training Centres Vipa Herzogenaurach A Richtung Höchstadt a. d. Aisch Richtung Forchheim Erlangen VIPA Gesellschaft für Visualisierung und Prozessautomatisierung mbh Ohmstraße Herzogenaurach Germany Tel. +49 (0) Fax +49 (0) Adi-Dassler-Sportplatz Richtung Haundorf Tuchenbach ST44 E45 Frauenaurach Erlangen- Frauenaurach A7 Tennenlohe Großgründlach A E45 Richtung Röthenbach a. d. Pegnitz Vipa Herzogenaurach ERH Ringstraße ERH4 Einsteinstraße Nutzungstraße ERH Schützengraben Erlanger Straße Herzogenaurach ST44 Niederndorf Neuses A E45 Cadolzburg Erlangen- Frauenaurach Mittlere Aurach Richtung Flughafen Nürnberg Zirndorf Fürth A7 Flughafen Nürnberg Nürnberg Hauptendorf WIFI Wirtschaftsförderungsinstitut der Wirtschaftskammer Oberösterreich Wiener Straße Linz, Austria Tel. +4 (0) Fax +4 (0) More information about the courses and training events in the WIFI Linz can be found under:

55 95 05

56 YASKAWA Contacts YASKAWA Headquarters YASKAWA Europe GmbH Robotics Division Yaskawastraße D-859 Allershausen Tel. +49 (0) 8 66/90-0 Fax +49 (0) 8 66/90-0 YASKAWA academy and sales offi ce Frankfurt YASKAWA Europe GmbH Robotics Division Hauptstraße 85 D Eschborn Tel. +49 (0) 6 96/ Fax +49 (0) 6 96/ YASKAWA Group A YASKAWA Austria Schwechat/Wien +4(0) CZ YASKAWA Czech s.r.o. Rudná u Prahy E YASKAWA Ibérica, S.L. Gavà/Barcelona F YASKAWA France SARL Saint-Aignan-de-Grand-Lieu FIN YASKAWA Finland Oy Turku +58-(0) GB YASKAWA UK Ltd. Banbury I YASKAWA Italia s.r.l. Torino IL YASKAWA Europe Technology Ltd. Rosh Ha ayin NL YASKAWA Benelux B.V. EB Son RUS YASKAWA Nordic AB Moskva SE YASKAWA Nordic AB Torsås SI YASKAWA Slovenia Ribnica TR YASKAWA Turkey Elektrik Ticaret Ltd. Sti. İstanbul ZA YASKAWA Southern Africa (PTY) Ltd Johannesburg Distributors BG Kammarton Bulgaria Ltd. Sofia CH Messer Eutectic Castolin Switzerland S.A. Dällikon DK Robotcenter Danmark Løsning EE RKR Seadmed OÜ Tallinn/Estonia GR Gizelis Robotics Nea Kifissia H Flexman Robotics Kft Budapest LT Profibus UAB Panevezys N Skala Robotech AS Lierstranda PL Integrator RHC Sp. z o.o. Torun PT ROBOPLAN Lda Aveiro RO Sam Robotics srl Timisoara RO MPL Automation S.R.L. Satu Mare +40 (0) YASKAWA academy Partner A WIFI Oberösterreich Wiener Str. 50 A-40 Linz T: +4 (0) F: +4 (0) YASKAWA academy Allershausen YASKAWA Europe GmbH Robotics Division Yaskawastraße D-859 Allershausen Tel. +49 (0) (0) Fax +49 (0) YASKAWA academy Eschborn YASKAWA Europe GmbH Robotics Division Hauptstraße 85 D Eschborn Tel. +49 (0) (0) Fax +49 (0) academy@yaskawa.eu.com We reserve the right to technical changes and error. A-0-04, A-Nr