ACTUATOR LA25 PRODUCT DATA SHEET

Transcription

1 PRODUCT DATA SHEET ACTUATOR LA25 Features and Options: 12 or 24 V DC permanent magnetic motor 900 N N load in push and pull Colour: Dark olive grey Protection class: IP66, furthermore the actuator can be washed down by a high pressure cleaner (IP69K static) Stroke length from mm Positioning options: Hall potentiometer, Hall PWM or Single Hall End of Stroke signal (EOS) Back fixture and piston rod eye material: Steel or stainless steel Heavy duty aluminium housing for harsh conditions Guided nut Safety nut in push or pull (2500N version only safety nut in push) Built-in electrical endstop Exchangeable cable Static safety factor: 2.0 Noise level: Max db(a) (At nominal voltage and with no load, according to EN ISO ) IC options including IC and Parallel Special anodised housing for extreme environments Usage: Duty cycle: 20%, 2 minutes continuous use followed by 8 minutes not in use Ambient temperature: -40 C to +85 C, full performance from +5 C to +40 C Storage temperature: -55 C to +105 C The LA25 is compatible with SMPS-T160 With its robust design, high IP degree and aluminium housing, the actuator LA25 is ideal for harsh environments where operation under extreme conditions is required. Furthermore, the compact dimensions of the LA25 make it applicable for confined spaces. This TECHLINE actuator comes with IC - Integrated controller. For more information on our IC options, please see: Page 1 of 24

2 Contents Technical specifications LA LA25 standard cable item numbers... 3 Speed, load and current curves LA25 Ordering example... 6 LA25 dimensions & Stroke tolerances... 7 Built-in dimensions... 8 LA25 Piston Rod Eyes... 9 LA25 Back fixture orientation...10 I/O Specifications: Actuator without feedback I/O Specifications: Actuator with endstop signal output I/O Specifications: Actuator with relative positioning - Single Hall...12 I/O Specifications: Actuator with endstop signals and relative positioning - Single Hall I/O Specifications: Actuator with absolute positioning - Analogue feedback...14 I/O Specifications: Actuator with endstop signals and absolute positioning - Analogue feedback...15 I/O Specifications: Actuator with absolute positioning - PWM...16 I/O Specifications: Actuator with endstop signals and absolute positioning - PWM I/O Specifications: Actuator with IC Basic I/O Specifications: Actuator with IC Advanced - with BusLink I/O Specifications: Actuator with Parallel...21 Environmental tests Climatic Environmental tests - Mechanical...23 Complying standards...24 Non-complying standards Page 2 of 24

3 Technical specifications LA25 12V: Push/Pull Max. (N) Self-lock min. (N) Push/Pull Without short circuit With short circuit Spindle pitch (mm) *Typical speed (mm/s) Standard stroke *Typical 12 V No load Full load length (mm) No load Full load V: Push/Pull Max. (N) Self-lock min. (N) Push/Pull Without short circuit With short circuit Spindle pitch (mm) *Typical speed (mm/s) Standard stroke *Typical 24 V No load Full load length (mm) No load Full load * The typical values can have a variation of ± 20% on the current values and ± 10% on the speed values. Measurements are made with an actuator in connection with a stable power supply and an ambient temperature at 20 C. LA25 standard cable item numbers LA25 cable item no. Length (mm) outside the actuator Page 3 of 24

4 Speed, load and current curves 12V motor, type A The values below are typical values made with a stable power supply and an ambient temperature at 20 C 14 LA25-12V Speed vs Thrust Speed [mm/s] mm pitch 6mm pitch 9mm pitch 12mm pitch Thrust [N] LA25-12V Current vs Thrust 4,5 4 3,5 3 Current [A] 2,5 2 1,5 3mm pitch 6mm pitch 9mm pitch 12mm pitch 1 0, Thrust [N] Page 4 of 24

5 Speed, load and current curves 24V motor, type B The values below are typical values made with a stable power supply and an ambient temperature at 20 C 14 LA25-24V Speed vs Thrust Speed [mm/s] mm pitch 6mm pitch 9mm pitch 12mm pitch Thrust [N] LA25-24V Current vs Thrust 2 1,8 1,6 1,4 Current [A] 1,2 1 0,8 0,6 3mm pitch 6mm pitch 9mm pitch 12mm pitch 0,4 0, Thrust [N] Page 5 of 24

6 LA25 Ordering example: 2 5 P P P X X X S S F F P M E E = B R E P C E F L 0 0 X X X XXX = BID (mm) 0 = Not specified 0 = Not specified Loadtype 0 = Push/Pull 1 = Push 2 = Pull * Feedback level by platform type None IC type Basic IC type Advanced IC type Parallel 0 = none 0 = none 0 = none Z = Parallel 1 = 0-10 V 1 = 0-10 V A = 0-10 V 2 = V B = V 3 = 4-20 ma C = 4-20 ma 4 = % D = % 5 = % E = % 9 = Special X = Special EOS (End Of Stroke) output 0 = No (only IC Basic) 1 = Yes (only IC Advanced) Cable: 0 = None S = Straight 0.75m T = Straight 1.5m (8-core, Note: If AMP is chosen = 6-core) R = Straight 5.0m (8-core, Note: If AMP is chosen = 6-core) X = Special Plug Type: 0 = None Is to be chosen, if cable and connectors are not wanted C = Flying leads Is to be chosen, if connector is not wanted J = Deutsch (DT4) K= AMP superseal X = Special Piston Rod Eye: 1 = Zink coated steel ø10,2 ( ) A = Stainless ø10.2 ( ) 2 = Zink coated steel + bushings ø10.2 B = Stainless + bushings ø = Zink coated ø 12.3 ( ) C = Stainless ø 12.3 ( ) 4 = Zinc coated steel + bushings ø 8.1 D = Stainless steel + bushings ø 8.1 X = special Backfixture rotation 1 = 0 degrees 2 = 90 degrees Back fixture type: 1 = Zink coated steel ø10.2 ( ) A = Stainless ø10.2 ( ) 2 = Zink coated steel + bushings ø10.2 B = Stainless + bushings ø = Zink coated ø 12.3 ( ) C = Stainless ø 12.3 ( ) 4 = Zinc coated steel + bushings ø 8.1 D = Stainless steel + bushings ø 8.1 X = special Colour : IP: Endstop : = = DarkGrey A= IP66 9 = Harsh environment housing (Special article number only) T = ATEX 0 = Power switch (Platform none) 1 = Signalswitch (Platform IC) Motor Type: Platform A = 12VDC normal B = 24VDC Normal 0 = None 3 = IC Integrated Controller Feedback Safety : 00 = None 0K = Single Hall 0A = Hall Potentiometer (Analogue feedback) 0F = PWM 00 = None 0A = Safety nut Stroke Length: Spindle Pitch: Actuator Type: XXX = mm 030 = 3 mm 060 = 6 mm 090 = 9 mm 120 = 12 mm 25 = LA25 Note: When the built-in dimensions (BID) are special, write xxx when ordering, write stroke + BID in system specification. Noise can occur if plastic bushings are not fitted in the Piston rod eye / Back fixture * IC options: IC LINbus Parallel LA25 actuator: Page 6 of 24

7 LA25 Dimensions Stroke tolerances: Platform options Descriptions Stroke tolerance Example for 200 mm stroke 25XXXXXXXXXX0 With built-in limit switches + 2 / - 2 mm 198 to 202 mm 25XXXXXXXXXX3 Integrated controller + 1 / - 3 mm 197 to 201 mm Built-in tolerances: Platform options Descriptions BID tolerance Example for 200 mm BID 25XXXXXXXXXXX All variants + 2 / - 2 mm 198 to 202 mm Page 7 of 24

8 Built-in dimensions: The built-in dimension depends upon the chosen safety option and stroke length. Please see the table below to decide upon the built-in dimension. Safety option Stroke length Spindle pitch Min. built-in Dimensions No safety option , 9 or No safety option Safety nut for push , 9 or Safety nut for push Safety nut for pull , 9 or No safety option , 9 or stroke No safety option stroke Safety nut for push , 9 or stroke Safety nut for push stroke Safety nut for pull , 9 or stroke No safety option , 9 or stroke No safety option stroke Safety nut for push , 9 or stroke Safety nut for push stroke Safety nut for pull , 9 or stroke Page 8 of 24

9 LA25 Piston Rod Eyes: Piston: , Zinc coated Piston: , Stainless steel AISI 304 Piston: , Zinc coated Piston: , Stainless steel AISI 304 Page 9 of 24

10 LA25 Back fixture orientation: Option 1 = 0 Option 2 = 90 Page 10 of 24

11 I/O specifications: Actuator without feedback: Input/Output Specification Comments Description Permanent magnetic DC motor. Brown V DC (+/-) Blue Red Recommended fuse for 12V is 8 Amp and for 24V it is 4 Amp Connect Brown to positive Connect Brown to negative Connect Blue to negative Connect Blue to positive Black Green Yellow Violet White I/O specifications: Actuator with endstop signal output Input/Output Specification Comments Description The actuator can be equipped with electronically controlled endstop signals out. IN OUT Brown V DC (+/-) Blue Recommended fuse for 12 V is 8 Amp and for 24 V it is 4 Amp Red Signal power supply (+) V DC Black Signal power supply GND (-) Connect Brown to positive Connect Brown to negative Connect Blue to negative Connect Blue to positive Current consumption: Max. 40 ma, also when the actuator is not running Green Endstop signal out Output voltage min. V IN - 2V Source current max. 100 ma Yellow Endstop signal in NOT potential free Violet White Page 11 of 24

12 I/O Specifications: Actuator with relative positioning - Single Hall Input/Output Specification Comments Description The actuator can be equipped with Single Hall that gives a relative positioning feedback signal when the actuator moves. Brown V DC (+/-) Blue Recommended fuse for 12 V is 8 Amp and for 24 V it is 4 Amp Red Signal power supply (+) V DC Black Signal power supply GND (-) Connect Brown to positive Connect Brown to negative Connect Blue to negative Connect Blue to positive Current consumption: Max. 40 ma, also when the actuator is not running Green Yellow Violet Single Hall output (PNP) Movement per single Hall pulse: LA25030 Actuator = 0.25 mm per pulse LA25060 Actuator = 0.5 mm per pulse LA25090 Actuator = 0.75 mm per pulse LA25120 Actuator = 1.0 mm per pulse Frequency: Frequency is Hz on Single Hall output depending on load. Pulse ON time is minimum 8ms.OFF time between two ON pulses is minimum 8ms. Overvoltage on the motor can result in shorter pulses. Diagram of Single Hall: Input Output voltage min. V IN - 2V Max. current output: 12 ma Max. 680 nf N.B. For more precise measurements, please contact LINAK A/S. Low frequency with a high load. Higher frequency with no load. Single Hall output Hall A Hall B Micro - Processor Fig.1 White Page 12 of 24

13 I/O Specifications: Actuator with endstop signals and relative positioning - Single Hall: Input/Output Specification Comments Description The actuator can be equipped with Single Hall that gives a relative positioning feedback signal when the actuator moves. Brown V DC (+/-) Blue Recommended fuse for 12 V is 8 Amp and for 24 V it is 4 Amp Red Signal power supply (+) V DC Black Signal power supply GND (-) Connect Brown to positive Connect Brown to negative Connect Blue to negative Connect Blue to positive Current consumption: Max. 40 ma, also when the actuator is not running Green Endstop signal out Output voltage min. V IN - 2V Source current max. 100 ma Yellow Endstop signal in NOT potential free Violet Single Hall output (PNP) Movement per single Hall pulse: LA25030 Actuator = 0.25 mm per pulse LA25060 Actuator = 0.5 mm per pulse LA25090 Actuator = 0.75 mm per pulse LA25120 Actuator = 1.0 mm per pulse Frequency: Frequency is Hz on Single Hall output depending on load. Pulse ON time is minimum 8ms. OFF time between two ON pulses is minimum 8ms. Overvoltage on the motor can result in shorter pulses. Diagram of Single Hall: Input Output voltage min. V IN - 2V Max. current output: 12 ma Max. 680 nf N.B. For more precise measurements, please contact LINAK A/S. Low frequency with a high load. Higher frequency with no load. Single Hall output Hall A Hall B Micro - Processor Fig.2 White Page 13 of 24

14 I/O Specifications: Actuator with absolute positioning - Analogue feedback: Input/Output Specification Comments Description The actuator can be equipped with electronic circuit that gives an analogue feedback signal when the actuator moves. Brown V DC (+/-) Blue Recommended fuse for 12 V is 8 Amp and for 24 V it is 4 Amp Red Signal power supply (+) VDC Black Signal power supply GND (-) Connect Brown to positive Connect Brown to negative Connect Blue to negative Connect Blue to positive Current consumption: Max. 60 ma, also when the actuator is not running Green Yellow Violet Analogue feedback 0-10 V (Feedback level 1) V (Feedback level 2) Tolerances +/- 0.2 V Max. current output: 1 ma Ripple max. 200 mv Transaction delay max. 20 ms Linear feedback 0.5% Source current max. 1 ma 4-20 ma (Feedback level 3) Special (Feedback level 9) Tolerances +/- 0.2 ma Transaction delay 20ms Linear feedback 0.5% Output: Source Serial resistance: 12V max 300 ohm 24V max. 900 ohm For all analogue feedbacks it is recommendable to have the actuator to activate its limit switches on a regular basis, to ensure more precise positioning White Page 14 of 24

15 I/O specifications: Actuator with endstop signals and absolute positioning - Analogue feedback: Input/Output Specification Comments Description The actuator can be equipped with electronic circuit that gives an analogue feedback signal when the actuator moves. Brown V DC (+/-) Blue Recommended fuse for 12 V is 8 Amp and for 24 V it is 4 Amp Connect Brown to positive Connect Brown to negative Connect Blue to negative Connect Blue to positive Red Signal power supply (+) V DC Current consumption: Black Signal power supply GND (-) Max. 60 ma, also when the actuator is not running Green Endstop signal out Output voltage min. V IN - 2V Source current max. 100 ma Yellow Endstop signal in NOT potential free Violet Analogue feedback 0-10 V (Feedback level 1) V (Feedback level 2) Tolerances +/- 0.2 V Max. current output: 1 ma Ripple max. 200 mv Transaction delay max. 20 ms Linear feedback 0.5% Source current max. 1 ma 4-20 ma (Feedback level 3) Special (Feedback level 9) Tolerances +/- 0.2 ma Transaction delay 20ms Linear feedback 0.5% Output: Source Serial resistance: 12V max 300 ohm 24V max. 900 ohm For all analogue feedbacks it is recommendable to have the actuator to activate its limit switches on a regular basis, to ensure more precise positioning White Page 15 of 24

16 I/O Specifications: Actuator with absolute positioning - PWM: Input/Output Specification Comments Description The actuator can be equipped with electronic circuit that gives an analogue feedback signal when the actuator moves. Brown V DC (+/-) Blue Recommended fuse for 12 V is 8 Amp and for 24 V it is 4 Amp Red Signal power supply (+) V DC Black Signal power supply GND (-) Connect Brown to positive Connect Brown to negative Connect Blue to negative Connect Blue to positive Current consumption: Max. 40 ma, also when the actuator is not running Green Yellow Violet White Digital output feedback % (Feedback level 4) % (Feedback level 5) Special (Feedback level 9) Output voltage min. V IN - 2V Tolerances +/- 2% Max. current output: 12 ma It is recommendable to have the actuator to activate its limit switches on a regular basis, to ensure more precise positioning Page 16 of 24

17 I/O specifications: Actuator with endstop signals and absolute positioning - PWM Input/Output Specification Comments Description The actuator can be equipped with electronic circuit that gives an analogue feedback signal when the actuator moves. Brown V DC (+/-) Blue Recommended fuse for 12 V is 8 Amp and for 24 V it is 4 Amp Red Signal power supply (+) V DC Black Signal power supply GND (-) Connect Brown to positive Connect Brown to negative Connect Blue to negative Connect Blue to positive Current consumption: Max. 40 ma, also when the actuator is not running Green Endstop signal out Output voltage min. V IN - 2V Source current max. 100 ma Yellow Endstop signal in NOT potential free Violet White Digital output feedback % (Feedback level 4) % (Feedback level 5) Special (Feedback level 9) Output voltage min. V IN - 2V Tolerances +/- 2% Max. current output: 12 ma It is recommendable to have the actuator to activate its limit switches on a regular basis, to ensure more precise positioning Page 17 of 24

18 I/O Specifications: Actuator with IC Basic Input/Output Specification Comments Description Brown Blue Easy to use interface with integrated power electronics (H-bridge). The actuator can also be equipped with electronic circuit that gives an asolute or relative feedback signal. The version with IC option cannot be operated with PWM (power supply) V DC + (VCC) Connect Brown to positive 12V, current limit 8A 24V, current limit 5A VDC - (GND) Connect Blue to negative 12V, current limit 8A 24V, current limit 5A Note: Do not change the power supply polarity on the brown and blue wires! Power supply GND (-) is electrically connected to the housing If the temperature drops below -10 C, all current limits will automatically increase to 9A for 12V, and 6A for 24V Red Black Extends the actuator Retracts the actuator On/off voltages: > 67% of V IN = ON < 33% of V IN = OFF Input current: 10 ma M H-Bridge Green Yellow Violet Analogue feedback 0-10 V (Feedback level 1) Standby power consumption: 12 V, 60 ma 24 V, 45 ma Ripple max. 200 mv Transaction delay 20 ms Linear feedback 0.5% Max. current output: 1 ma It is recommendable to have the actuator to activate its limit switches on a regular basis, to ensure more precise positioning. White Single Hall output (PNP) Signal GND Output voltage min. V IN - 2V Max. current output: 12 ma For more information see fig.2, page 13 Page 18 of 24

19 I/O Specifications: Actuator with IC Advanced - with BusLink Input/Output Specification Comments Description Brown Blue Easy to use interface with integrated power electronics (H-bridge). The actuator can also be equipped with electronic circuit that gives an absolute or relative feedback signal. IC Advanced also provides a wide range of possibilities for customisation. The version with IC option cannot be operated with PWM (power supply) V DC + (VCC) Connect Brown to positive 12V, current limit 8A 24V, current limit 5A V DC - (GND) Connect Blue to negative 12V, current limit 8A 24V, current limit 5A Note: Do not change the power supply polarity on the brown and blue wires! Power supply GND (-) is electrically connected to the housing Current limit levels can be adjusted through BusLink If the temperature drops below -10 C, all current limits will automatically increase to 9A for 12V, and 6A for 24V Red Black Extends the actuator Retracts the actuator On/off voltages: > 67% of V IN = ON < 33% of V IN = OFF Input current: 10 ma Green Yellow Endstop signal out Endstop signal in Output voltage min. V IN - 2V Source current max. 100 ma Endstop signals are NOT potential free. Endstop signals can be configured with BusLink software according to any position needed. Only use one virtual endstop - keep one end open for initialisation. (See I/O specifications for endstop on page 11) M H-Bridge Page 19 of 24

20 I/O Specifications: Actuator with IC Advanced - with BusLink Input/Output Specification Comment Violet White Analogue feedback (0-10V): Configure any high/low combination between 0-10 V Single Hall output (PNP) Digital output feedback PWM: Configure any high/low combination between 0-100% Analogue feedback (4-20 ma): Configure any high/low combination between 4-20 ma All absolute value feedbacks (0-10V, PWM and 4-20 ma) Signal GND Ripple max. 200 mv Transaction delay 20 ms Linear feedback 0.5% Max. current output. 1 ma Output voltage min. V IN - 2V Max. current output: 12 ma Please be aware that when choosing single hall, feedback position readout and virtual endstops are not available in BusLink. For more information, see fig. 2, page 13 Output voltage min. V IN -2V Frequency: 75 Hz ± 10 Hz as standard, but this can be customised. Duty cycle: Any low/high combination between 0 and 100 percent. Open Drain source current max. 12 ma Tolerances +/- 0.2 ma Transaction delay 20 ms Linear feedback 0.5% Output: Source Serial resistance: 12 V max. 300 ohm 24 V max. 900 ohm Standby power consumption: 12 V, 60 ma 24 V, 45 ma It is recommendable to have the actuator to activate its limit switches on a regular basis, to ensure more precise positioning BusLink is available for IC Advanced and can be used for: Diagnostics, manual run and configuration Please note that the BusLink cables must be purchased separately from the actuator! Item numbers for BusLink cables: USB2LIN: USB2LIN05, USB2LIN06 and onwards Adaptor cable: Page 20 of 24

21 I/O specifications: Actuator with Parallel Input/Output Specification Comments Description Brown Blue Parallel drive of up to 8 actuators. A master actuator with an integrated H-bridge controller controls up to 7 slaves. The version with IC option cannot be operated with PWM (power supply) V DC + (VCC) Connect Brown to positive 12V, current limit 8A 24V, current limit 5A V DC - (GND) Connect Blue to negative 12V, current limit 8A 24V, current limit 5A Note: Do not change the power supply polarity on the brown and blue wires! The parallel actuators can run on one OR separate power supplies Power supply GND (-) is electrically connected to the housing Current limit levels can be adjusted through BusLink (only one actuator at a time for parallel) If the temperature drops below -10 C, all current limits will automatically increase to 9A for 12V, and 6A for 24V Red Black Extends the actuator Retracts the actuator On/off voltages: > 67% of V IN = ON < 33% of V IN = OFF Input current: 10 ma It does not matter where the in/out signals are applied. You can either choose to connect the signal cable to one actuator OR you can choose to connect the signal cable to each actuator on the line. Either way this will ensure parallel drive Green Endstop signal out Output voltage min. V IN - 2V Source current max. 100 ma Yellow Endstop signal in NOT potential free M H-Bridge M H-Bridge M H-Bridge M H-Bridge Violet White Parallel communication: Violet cords must be connected together Signal GND: White cords must be connected together Standby power consumption: 12 V, 60 ma 24 V, 45 ma No feedback available during parallel drive BusLink is available for Parallel and can be used for: Diagnostics Service counter is available with Parallel Parallel actuator configurations can be changed through BusLink, but all actuators need the same configurations! Please note that the BusLink cables must be purchased separately from the actuator! Item numbers for BusLink cables: USB2LIN: USB2LIN05, USB2LIN06 and onwards Adaptor cable: Page 21 of 24

22 Environmental tests Climatic Test Specification Comment TRD number Cold test EN (Ab) Storage at low temperature: Temperature: - 40 C Duration: 72 h Actuator is not connected/operated Tested at room temperature EN (Ad) Storage at low temperature: Temperature: -55 C Duration: 24 h Actuator is not connected Tested at room temperature Operating at low temperature: Temperature: -40 C Duration: 4 h Tested at room temperature within 5 minutes overload Dry heat EN (Bb) Storage at high temperature: Temperature: +85 C Duration: 72 h Actuator is not connected/operated Tested at room temperature EN (Bb) Storage at low temperature: Temperature: +105 C Duration: 24 h Actuator operated at high temperature Damp heat EN (Db) Damp heat, Cyclic: Relative humidity: % High temperature: +55 C in 12 hours Low temperature: +25 C in 12 hours Duration: 21 cycles * 24 hours Actuator is operated during test Salt mist. EN ISO 9227 Dynamic salt spray test: Salt solution: 5% sodium chloride (NaCl) Temperature: 35 ± 2 C Duration: 500 h Actuator is operated Thermal shock Dunk test: Actuator is heated to +85 C for 4 h and submerged into a 0 C cold saltwater-detergent solution for 2 h Followed by 18 h dry time Duration: 5 cycles TRD5675 TRD5675 TRD5675 TRD5675 TRD5677 TRD5678 TRD5679 Page 22 of 24

23 Degrees of protection EN IP66 IP6X - Dust: Dust-tight, No ingress of dust Actuator is not activated TRD5680 Rain EN IP66 DIN IP69K IPX6 - Water: Ingress of water in quantities causing harmful effects is not allowed Duration: 100 litres pr. minute in 3 minutes Actuator is not activated IPX9K: High pressure cleaner Temperature: +80 C Water pressure: bar Water flow: l/min Duration: 30 sec. each at 4 different angles 0, 30, 60 and 90 Actuator is not activated Ingress of water in quantities causing harmful effects is not allowed Dynamic rain test: Actuators exposed to continous rain Actuators operated and side loaded with 5N Duration: cycles and 240 h TRD5682 TRD5680 TRD5681 Environmental tests - Mechanical Test Specification Comment TRD number Mechanical Shock (Handling) - Drop test Mechanical Shock Operational Vibration Random 3 drops on 6 faces onto a concrete floor. Drop height: 500 mm on all faces Peak Pulse Amplitude: 50 G Pulse Duration: 11 ms Number of pulses: 18 total - 3 in each direction for all three axis Peak Pulse Amplitude: 30 G Pulse Duration: 18 ms Number of pulses: 18 total - 3 in each direction for all three axis Peak Pulse Amplitude: 25 G Pulse Duration: 6 ms Number of pulses: 6000 total in each direction for all three axis Random vibration: From 18 Hz to 1000 Hz Duration: 2 h/axis TRD5683 TRD5684 TRD5684 TRD5684 TRD5684 Page 23 of 24

24 Complying standards: Standard Specification FOCUS ON 2004/104/EC EN/IEC : A1: 2009 EN/IEC : 2008 Automotive EMC Directive 2004/104/EC on electrical and electronic car components Safety of machinery - Electrical equipment of machines - Part 1: General requirements Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines VEHICLES AND MOBILITY INDUSTRIAL AUTOMATION INDUSTRIAL AUTOMATION PLATFORMS AND LIFTS EN/IEC : 2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity for industrial environments INDUSTRIAL AUTOMATION EN/IEC : 2005 EN/IEC : A1:2011 EN/IEC : A1:2011 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial environments Electromagnetic compatibility (EMC) - Part 6: Generic standards - Section 4: Emission standard for industrial environments INDUSTRIAL AUTOMATION INDUSTRIAL AUTOMATION INDUSTRIAL AUTOMATION EN 13309: 2010 Construction machinery CONSTRUCTION EN/ISO 13766: 2006 Earth-moving machinery - Electromagnetic compatibility CONSTRUCTION EN/ISO 14982: 2009 EU recreational crafts directive 94/25/EC Non-complying standards: Standard 2004/104/EC Agricultural and forestry machines - Electromagnetic compatibility Explanation MOBILE AGRICULTURE OUTDOOR POWER EQUIPMENT Please note that this product cannot be approved according to the medical electrical equipment standard. Due to the combination of the aluminium cast housing and the embedded PCB, we do not fulfill the regulations according to leakage current. Copyright LINAK MA M E. Chapter 5.21 Terms of use The user is responsible for determining the suitability of LINAK products for specific application. LINAK takes great care in providing accurate and up-to-date information on its products. However, due to continuous development in order to improve its products, LINAK products are subject to frequent modifications and changes without prior notice. Therefore, LINAK cannot guarantee the correct and actual status of said information on its products. While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK. All sales are subject to the Standard Terms of Sale and Delivery for LINAK. For a copy hereof, please contact LINAK. Page 24 of 24 FOR MOUNTING INSTRUCTIONS AND GUIDANCE IN USAGE, PLEASE SEE THE RELEVANT USER S MANUALS