(1.50) .035 MIN HOLE AND SLOT MIN

Transcription

1 X.096 THRU ISION HISTORY DESCRIPTION DTE PPROVED DDED DETIL WITH PINOUT 6/7/07 KMW DDED SENSOR ORIGINS PG. 8//07 KMW NOTE : THIS DRWING IS NOT TO E USED FOR MNUFCTURE OR INSPTION NOTE : DRWINGS NOT OWN TO SCLE (.78) (.9) SMT PRT NUMER FT-05-0-F-D-K (.08) (.8) (.50).07. MX (.).80 MX (.)..05 MIN HOLE ND SLOT MIN (.) (.) THIRD NGLE PROJTION PROPRIETRY NOTICE THE INFORMTION CONTINED HEREIN IS PROPRIETRY TO LORD CORPORTION ND LL NOT E WHOLE OR IN PRT OR USED FOR NY DESIGN OR MNUFCTURE EXCEPT WHEN SUCH USER POSSESSES DIRT, WRITTEN UTHORIZTION FROM LORD CORPORTION. SURFCE RE (SQ. IN.) F.M.P. = FOR MNUFCTURING PURPOSES LL DIMENSIONS RE TO POINTS OF INTERSTION DIMENSIONING/TOLERNCING PER SME Y ITIONS, CRONYMS, TERMINOLOGY PER TS-07 MCHINED SURFCES = 5µin (.µm) MX REK LL RP EDGES.005in -.05in (0.mm - 0.6mm) VERGING OF DIMETERS NOT PERMISSILE LL DIMENSIONS RE IN INCHES DIMENSIONS IN [ ] RE IN MILLIMETERS CLC. WT. (L.) ICD Y Y CORPORTION CGE SIZE DRWING NO. INTERFCE CONTROL DRWING DM-CV5 (-0, -5, -5) ICD OF 5 LORD PROPRIETRY

2 MGNETOMETER ORIGIN NOTE: Minimum " keep-out sphere. void ferromagnetic materials and significant DC currents within " of magnetometer to preserve magnetometer accuracy. Large currents and ferromagnetic materials require greater keep-out distance. 0. INERTIL SENSOR ORIGIN 0.6 THIRD NGLE PROJTION PROPRIETRY NOTICE THE INFORMTION CONTINED HEREIN IS PROPRIETRY TO LORD CORPORTION ND LL NOT E WHOLE OR IN PRT OR USED FOR NY DESIGN OR MNUFCTURE EXCEPT WHEN SUCH USER POSSESSES DIRT, WRITTEN UTHORIZTION FROM LORD CORPORTION. SURFCE RE (SQ. IN.) F.M.P. = FOR MNUFCTURING PURPOSES LL DIMENSIONS RE TO POINTS OF INTERSTION DIMENSIONING/TOLERNCING PER SME Y ITIONS, CRONYMS, TERMINOLOGY PER TS-07 MCHINED SURFCES = 5µin (.µm) MX REK LL RP EDGES.005in -.05in (0.mm - 0.6mm) VERGING OF DIMETERS NOT PERMISSILE LL DIMENSIONS RE IN INCHES DIMENSIONS IN [ ] RE IN MILLIMETERS CLC. WT. (L.) ICD Y Y CORPORTION CGE SIZE DRWING NO. INTERFCE CONTROL DRWING DM-CV5 (-0, -5, -5) ICD OF 5 LORD PROPRIETRY

3 x SOLDERMSK PULL-CK RE.80 PD LYOUT FOR PC MOUNT CONNTOR SEE NOTE R..8. MIN SOLDER PD see note.78.6 PIN.00.6 SOLDERMSK PULL-CK.5 MX X MOUNTING FSTENER -56 x /" button head screw 00 series stainless or brass (see note ) e.g. MCMSTER Torque to in-lbs NOTE : For solderable fastener: PEM p/n SMTSO-56-ET see product datasheet for details. lternate: thru (with or without copper pad) for conventional nut mounting (see note ). NOTE : If using PEM fastener in NOTE, minimum PC thickness is 0.060". Confirm board tolerances will not fall below this minimum value..060 MIN see NOTE X PEM FSTENER See NOTES - NOTE : Reccomended PC connectors: HRWIN M or keyed connector HRWIN M50-05 THIRD NGLE PROJTION PROPRIETRY NOTICE THE INFORMTION CONTINED HEREIN IS PROPRIETRY TO LORD CORPORTION ND LL NOT E WHOLE OR IN PRT OR USED FOR NY DESIGN OR MNUFCTURE EXCEPT WHEN SUCH USER POSSESSES DIRT, WRITTEN UTHORIZTION FROM LORD CORPORTION. SURFCE RE (SQ. IN.) F.M.P. = FOR MNUFCTURING PURPOSES LL DIMENSIONS RE TO POINTS OF INTERSTION DIMENSIONING/TOLERNCING PER SME Y ITIONS, CRONYMS, TERMINOLOGY PER TS-07 MCHINED SURFCES = 5µin (.µm) MX REK LL RP EDGES.005in -.05in (0.mm - 0.6mm) VERGING OF DIMETERS NOT PERMISSILE LL DIMENSIONS RE IN INCHES DIMENSIONS IN [ ] RE IN MILLIMETERS CLC. WT. (L.) ICD Y Y CORPORTION CGE SIZE DRWING NO. INTERFCE CONTROL DRWING DM-CV5 (-0, -5, -5) ICD OF 5 LORD PROPRIETRY

4 X -56 UNC-.5 MIN X MOUNTING FSTENER -56 x /" button head screw 00 series stainless (see note ) e.g. MCMSTER Torque to in*lbs.78 Example cable shown: SMT FFSD-05-D N-R.5 MX [OPTIONL] HIGH PRISION MOUNTING X MIN PRESS FIT /" DOWEL PIN E.G MCMSTER p/n 905 (NONMGNETIC STINLESS ONLY) Pin Location Example PC shown with SMT F-05-0-L-D-SM see NOTE.5 MIN.5 MX S SSEMLED NOTE : lternative cable connectors include SMT p/ns: EHF-05-0-L-D-SM-LC EHF-05-0-L-D-SM F-05-0-L-D-SM-LC THIRD NGLE PROJTION PROPRIETRY NOTICE THE INFORMTION CONTINED HEREIN IS PROPRIETRY TO LORD CORPORTION ND LL NOT E WHOLE OR IN PRT OR USED FOR NY DESIGN OR MNUFCTURE EXCEPT WHEN SUCH USER POSSESSES DIRT, WRITTEN UTHORIZTION FROM LORD CORPORTION. SURFCE RE (SQ. IN.) F.M.P. = FOR MNUFCTURING PURPOSES LL DIMENSIONS RE TO POINTS OF INTERSTION DIMENSIONING/TOLERNCING PER SME Y ITIONS, CRONYMS, TERMINOLOGY PER TS-07 MCHINED SURFCES = 5µin (.µm) MX REK LL RP EDGES.005in -.05in (0.mm - 0.6mm) VERGING OF DIMETERS NOT PERMISSILE LL DIMENSIONS RE IN INCHES DIMENSIONS IN [ ] RE IN MILLIMETERS CLC. WT. (L.) ICD Y Y CORPORTION CGE SIZE DRWING NO. INTERFCE CONTROL DRWING DM-CV5 (-0, -5, -5) ICD OF 5 LORD PROPRIETRY

5 PIN FUNCTIONS PIN # NET NME FUNCTION NOTES USDM US DT- NOTE,5 USDP US DT + NOTE,5 Vin POWER SUPPLY + RxD URT receive (host to CV5) 5 TxD URT transmit (CV5 to host) THIRD NGLE PROJTION PROPRIETRY NOTICE THE INFORMTION CONTINED HEREIN IS PROPRIETRY TO LORD CORPORTION ND LL NOT E WHOLE OR IN PRT OR USED FOR NY DESIGN OR MNUFCTURE EXCEPT WHEN SUCH USER POSSESSES DIRT, WRITTEN UTHORIZTION FROM LORD CORPORTION. SURFCE RE (SQ. IN.) NOTE NOTE 6 GPIO LOGIC LEVEL GPIO NOTE 7 GPIO LOGIC LEVEL GPIO (and pps input) NOTE 8 GND SIGNL GROUND & POWER SUPPLY RETURN 9 GPIO LOGIC LEVEL GPIO NOTE 0 DISLE LOGIC LEVEL DISLE (OPEN OR LOW = ENLE) MOUNTING HOLES CHSSIS CHSSIS GROUND NOTE NOTE : primary interface communications is via either uart or usb. unused interface pins may be left unconnected NOTE : for best EMC performance, tie CHSSIS (i.e. the three mounting holes) to a local ground (e.g. pcb groundplane, airframe ground, etc.) CHSSIS and GND can be the same or different grounds, see SOLUTE MXIMUM RTINGS table for limits NOTE : currently implemented as input only for Pulse Per Second (PPS) timing input. leave unconnected or wire to GND if not used. NOTE : future functionality; not currently implemented. these pins can be left unconnected, or wired to GND, or wired to a TTL/CMOS compatible device for possible future usage. NOTE 5: CV5-0 does not make use of US connections (pins /) these pins may be left unconnected if US is unused. F.M.P. = FOR MNUFCTURING PURPOSES LL DIMENSIONS RE TO POINTS OF INTERSTION DIMENSIONING/TOLERNCING PER SME Y ITIONS, CRONYMS, TERMINOLOGY PER TS-07 MCHINED SURFCES = 5µin (.µm) MX REK LL RP EDGES.005in -.05in (0.mm - 0.6mm) VERGING OF DIMETERS NOT PERMISSILE LL DIMENSIONS RE IN INCHES DIMENSIONS IN [ ] RE IN MILLIMETERS CLC. WT. (L.) ICD Y Y SOLUTE MXIMUM RTINGS Parameter Limit Notes Vin to GND ±V NOTES, Logic I/O to GND -0.V to Vin+0.V ND not to exceed +5.V NOTES, GPIO to GND ±V NOTE DISLE to GND ±V NOTE GND to CHSSIS ±V NOTE Operating Temperature -0 C to +85 C Mechanical Shock 500g NOTE : Power supply is PROTTED against ±V, but will not OPERTE over that full range. See INTERFCE OPERTING SPIFICTIONS table for operational limits. NOTE : lso protected against ESD and other high-voltage / low-energy transients. NOTE : applied to pins: RxD, TxD, USDM, USDP, GPIO, GPIO INTERFCE OPERTING SPIFICTIONS Parameter MIN TYP MX NOTES Power Supply Voltage (Vin) +.V +5.V Note Power Consumption 00mW DC Input Logic Low (Vil) 0.9V NOTES,, DC Input Logic High (Vih).V NOTES,, DC Output Logic Low (Vol) 0.V NOTES,, DC Output Logic High.6V NOTES,, Disable Input Threshold 0.V.6V NOTES,5 NOTE : ll voltages are referenced to the GND pin (pin 8). NOTE : pplies to pins: RxD, TxD, USDM, USDP, GPIO, GPIO, GPIO. NOTE : Nominal input impedance at RxD pin is 0Kohm to +V. Nominal input impedance at GPIO// pins is 0Kohm to GND. Nominal input impedance at USDP pin is Kohm to +V. Nominal input impedance at USDM pin is 0Kohm to +V. NOTE : pplies when sourcing/sinking up to 6m. NOTE 5: Nominal input impedance at DISLE pin is Mohm to GND when DISLE voltage is between 0V and +5.6V. The DISLE pin can be tied to GND or left unconnected when unused. CORPORTION CGE SIZE DRWING NO. INTERFCE CONTROL DRWING DM-CV5 (-0, -5, -5) ICD 5 OF 5 LORD PROPRIETRY