DH410-XXXXX Ver. 6 Rel. 10/7/2013

Transcription

1

2 C.E. Electronics, Inc. 7 Industrial Drive Bryan, OH 4356 PH (49) FX (49) DH4XXXXX Ver. 6 Rel. /7/3 COMPETITOR DOT MATRIX RENEWAL PARTS Lens: 456 Lens: 4693 GRAY DOT MATRIX LED DIGITAL INDICATOR Dot matrix LED digital indicator for floor position display, as well as car direction, if desired. Any alphanumeric or custom character can be displayed in either double digit with single "UP/DOWN" arrows or four digit floor designations. Typical Applications CarOP Panel Transomcar or Hall Features Low cost design Self contained unit Latched input Self testing Scrolling Passing chime output Error detection and correction feature UL listed NOTE: CNECTI ' CABLE SUPPLIED WITH PLUGIN CNECTOR SUPPLIED " CHARACTERS. If a special voltage is required, please consult factory.. VAC not required for power supply on Micro Comm units *.65" PANEL PREPARATI #63 x /" STUD MIN (TYP. 4 PLACES) 7.5" 5.75" CUTOUT TOLERANCE: +.. TO ORDER:SPECIFY DH4 X X X X X.9" COLOR: "" "R" "A" MIXED AMBER "G" GREEN "W" WHITE "B" BLUE NUMBER OF S: "" 6 OR LESS "" 3 "M" MICRO COMM * LENS: "R" "G" GRAY "X" NO LENS SIGNAL FORMAT: "" SINGLE LINE/FLOOR "" BINARY "3" UNITS & TENS "4" GRAY CODE "5" INVERTED BINARY "6" SPECIAL "X" IF MICRO COMM SIGNAL VOLTAGE: "A" POSITIVE 6VDC, 64VAC "B" POSITIVE 44VDC, 44VAC "C" VAC "D" POSITIVE 5VDC "E" NEGATIVE 6VDC "F" NEGATIVE 44VDC "G" NEGATIVE 5VDC "X" IF MICRO COMM

3 9 A B CD E F 9 A B CD E F SCROLL RATE: NO SCROLL FAST SCROLL F SLOW SCROLL UNDANCY: SELFTEST MODE LOW UNDANCY F HIGH UNDANCY JOB# DH33 DH4 OPTIAL CHIME PORT J5 PASSING CHIME S ISO6 ISO5 ISO4 ISO3 ISO ISO 3 R5 3 S R6 R3 R4 R R J3 J ARROW VOLTAGE SIGNAL VOLTAGE (FROM CTROLLER) E LINE PER FLOOR FLOOR SIGNAL FLOOR SIGNAL FLOOR 3 SIGNAL FLOOR 4 SIGNAL FLOOR 5 SIGNAL FLOOR 6 SIGNAL FLOOR 7 SIGNAL FLOOR SIGNAL FLOOR 9 SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR 3 SIGNAL FLOOR 4 SIGNAL FLOOR 5 SIGNAL FLOOR 6 SIGNAL UP ARROW DOWN ARROW BINARY A () A () A3 (4) A4 () A6 (3) A5 (6) BLACK WHITE GREEN ORANGE BLUE WHT/BLK /BLK GRN/BLK ORG/BLK BLU/BLK BLK/WHT /WHT GRN/WHT BLU/WHT BLK/ WHT/ ORG/ J BLU/ /GRN COMM ARROW COMM ISO7 R LY USED FOR E LINE PER FLOOR ABOVE 6 FLOORS R DH4 DIP SWITCH DETAIL CHARACTER SET SELECTOR 3 4 ARROW COUNTERSCROLL NOT USED DRIVER BOARD CE3 5 ARROW SCROLL (Y/N) DISPLAY BOARD CE ERROR CORRECTI SENSITIVITY DEFAULT SETTINGS ROTARY SWITCH S ROTARY SWITCH S CE3E CODE VERSI ISO VAC N/C 5 VAC R7 R JP 5 6 D U Competitor Series Discrete Input Dot Matrix Displays FLOOR 7 SIGNAL FLOOR SIGNAL FLOOR 9 SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR SIGNAL FLOOR 3 SIGNAL FLOOR 4 SIGNAL FLOOR 5 SIGNAL FLOOR 6 SIGNAL FLOOR 7 SIGNAL FLOOR SIGNAL FLOOR 9 SIGNAL FLOOR 3 SIGNAL FLOOR 3 SIGNAL BLACK WHITE GREEN ORANGE BLUE WHT/BLK /BLK GRN/BLK ORG/BLK BLU/BLK BLK/WHT /WHT GRN/WHT BLU/WHT J3 SEE NOTE ( ) BELOW NOTE A: THE SIGNAL AND ARROW COMMS ARE TIED TOGETHER THE DRIVER BOARD. IF ARROW SOURCE IS DIFFERENT THAN SIGNAL SOURCE, CTACT TECH SUPPORT AT FOR FURTHER INFORMATI. NOTE B: THE SIGNAL AND ARROW COMMS HAVE BEEN SEPARATED BY THE FACTORY. 6//7 3 C.E. ELECTRICS, INC. 7 Industrial Drive Bryan, Ohio 4356 (49) PRODUCT DWG. NO. REV: DISCRETE DOT MATRIX DISPLAYS DH33_4_4 DIS

4 A7 A6 A5 A4 A3 A A BINARY BITS BINARY FLOOR CHART INSTALLATI GUIDE. MAKE SURE THE RESISTORS ARE FULLY SEATED IN THEIR SOCKETS.. CNECT 5VAC TO THE OUTER TERMINALS OF CNECTOR J. THE CENTER TERMINAL HAS NO CNECTI. 3. SET ROTARY SWITCH S TO "" TO START SELFTEST. THE DISPLAY WILL CYCLE THROUGH THE FLOOR DATA. THIS SHOWS WHAT FLOOR MARKINGS WILL DISPLAY AND ALLOWS ADJUSTMENT OF THE SCROLL RATE AND OPTIAL PASSING CHIME VOLUME. SET S TO AT LEAST "" (FACTORY DEFAULT IS "") TO END SELFTEST. 4. MAKE SURE THE SIGNAL CABLE(S) IS PLUGGED INTO THE DRIVER BOARD CORRECTLY. 5. CNECT THE SIGNAL CABLE(S) TO THE CTROLLER. THE VOLTAGE AND DC POLARITY ARE MARKED THE REVERSE SIDE. THE UNIT WORKS LIKE A LIGHT BULB; IT NEEDS VOLTAGE FROM COMM TO THE SELECTED. 6. IF THE IS DC AND YOU SUSPECT THE POLARITY IS WRG, PUT THE SELECTED FLOOR WIRE TO COMM AND COMM TO THE SELECTED FLOOR. IF THE UNIT DISPLAYS THE FLOOR, CTACT TECH SUPPORT. 7. IF THE FORMAT IS SINGLE LINE PER FLOOR, LY E WIRE SHOULD HAVE VOLTAGE PRESENT (WITH REFERENCE TO COMM) AT ANY TIME.. IF THE UNIT DOES NOT SEEM TO WORK PROPERLY, RECHECK THE ABOVE STEPS. IF THE PROBLEM CTINUES, RECORD THE SERIAL NUMBER FROM THE WHITE LABEL THE UNIT AND EXACTLY WHAT THE UNIT DISPLAYS AT EACH FLOOR, THEN CTACT TECH SUPPORT AT C.E. ELECTRICS, INC. 7 Industrial Drive Bryan, Ohio 4356 (49) PRODUCT DWG. NO. REV: 6/4/7 N/A COMPETITOR SERIES BINARY FLOOR CHART COMP_BINCHART_RS

5 9 A B CD E F DH4 / DH4XM JOB# DIP SWITCH LEGEND S DEFAULT SETTINGS DISPLAY BOARD# S FM MB J4 CODE VERSI J PASSING CHIME FLOORS: 64 REAR FA ROTARY SWITCH S CE39 J 3 MICRO COMM R5 R4 R3 S S 3 DRIVER BOARD# CE39 ROLL RATE ADJUSTMENT SELFTEST JACK CODE VERSI To SELFTEST display unit, short the two pins on the S header and release. NOTE: If S is a rotary switch, set it to "F" and back to to selftest. S3 DIP SWITCH DETAIL S3 DEFAULT SETTINGS 3 NOT USED FIRE MAIN BLANK FLOOR SELECTI DIP switch (MB) has no function with this unit. The Micro Comm driver must be programmed to send messages with the level required to activate the features listed below. To blank the display during a fire main (level three) message, turn on DIP switch (FM). To blank the display during a fire alternate (level two) message, remove resistor R3 (FA) from the board. Do not program a floor value for Floor 63 if the Fire Blanking feature is required. DIP switches 3 off is an all call using travel signals. DIP switches 3 on and resistor R5 (64) removed is an all call using arrival signals. The floor address switches setup the display arrows as arrival (hall) arrows. Refer to the "S3 DIP SWITCH DETAIL" and turn on the floor address switches whose value adds up to the desired floor. For example, to display the arrows only when the unit is at floor 9, turn on switches 3, 4, and 7 (values,, and 6: ++69). The Micro Comm driver must be set up to send arrival information. To operate this unit as a rear lantern, remove resistor R4 (REAR) from the board. NOTE: The Micro Comm driver must be sending the MC data stream to use this feature. Call Tech Support at for more information. NOTE: MUST BE USED WITH A CLASS POWER SUPPLY. 6/6/7 C.E. ELECTRICS, INC. 7 Industrial Drive 39, 7, 4 Bryan, Ohio 4356 (49) PRODUCT REV: DH4 / DH4XM 4DIGIT DOT MATRIX DWG. NO. DH44XM_