GE Intelligent Platforms

Transcription

1 GE Intelligent Platforms Operator Interface Products QuickPanel + 7 Display Adapter Kit IC755ACC07ADP Installation Guide, GFK-2895A October 2014

2 1. Overview Attention: The UL Markings, ATEX Marking, and all environmental ratings (NEMA4, UL50 Type 4X, and IP65) have not been validated for the QuickPanel + 7 Display when used with the adapter. Therefore, the agency compliances and standards do not apply to a QuickPanel + 7 Display with an installed Adapter Kit. Note: The use of a correctly installed adapter does not affect the QuickPanel + product s compliance with CE Marking. The QuickPanel + 7 Display adapter kit facilitates mounting the QuickPanel + 7 Display into a panel with a cutout previously sized for a QuickPanel 8 Display. The QuickPanel + 7 Display should first be inserted into the adapter and secured using the clamps provided with the display. The assembly is then inserted into the 8 cutout in the customer panel. Note: For user manuals, product updates, and other information, go to the Support website at and refer to Operator Interfaces and PC. 2 IC755ACC07ADP Installation Guide GFK-2895A

3 1.1 Functional Compatibility The adapter kit can be used with the following QuickPanel + 7 Display units: Part Number IC755CxW07CDx Description QuickPanel + 7 Display 1.2 Adapter Kit Contents Component Plastic adapter assembly (with attached gasket) Qty Mounting clamps 4 Slotted screws 8 1 GFK-2895A IC755ACC07ADP Installation Guide 3

4 1.3 Adapter Kit Features The following figure displays the QuickPanel + 7 Display and adapter kit assembly properly installed into a customer panel. Mounting bracket (Qty 4) Slotted screw (Qty 8) QuickPanel + Display Adapter Customer panel Assembly Installed in Customer Panel (Side View) 4 IC755ACC07ADP Installation Guide GFK-2895A

5 1.4 Panel Cutout Dimensions The QuickPanel + 7 Display adapter kit requires the panel cutout dimensions displayed in the following figure. Adapter mm (7.34 in) mm (8.97 in) Adapter Kit in Customer Panel (Rear View) GFK-2895A IC755ACC07ADP Installation Guide 5

6 2. Installation Notes: The unit will not fit through the panel cutout with a Secure Digital (SD) card not fully inserted and recessed in the port. The unit will not fit through the cutout with cables attached. To install the QuickPanel + 7 Display adapter assembly 1. If there is an SD card in the QuickPanel + 7 Display SD port, remove it. Also remove any cables that may interfere with installation. 2. Insert the QuickPanel + 7 Display into the adapter/gasket assembly until the side snaps click into the display housing. Maintain the orientation of the display in relation to the adapter to ensure proper clearance around display ports and cooling vents. 6 IC755ACC07ADP Installation Guide GFK-2895A

7 Adapter assembly Display Adapter side snap (Qty 2) Adapter/Gasket Assembly with Side Snaps 3. Adjust the mounting bracket screw so the bottom guide on the screw contacts the bottom surface of the metal bracket body. The guide assists with mounting bracket insertion. Bracket body Guide Mounting Bracket Guide GFK-2895A IC755ACC07ADP Installation Guide 7

8 4. Install the four mounting brackets supplied with each QuickPanel + 7 Display. Use the display housing slots and the round adapter recesses to locate each of the brackets. Adapter recess Display housing slot Display Housing Slot and Adapter Recess Mounting bracket (Qty 4) Installed Mounting Bracket 8 IC755ACC07ADP Installation Guide GFK-2895A

9 Installed Mounting Bracket (Close-up) 5. Using a #2 Phillips screwdriver, torque each screw to a maximum of 0.11 to 0.23 Nm (1 to 2 in-lb). GFK-2895A IC755ACC07ADP Installation Guide 9

10 6. Insert the QuickPanel + 7 Display adapter assembly into the cutout panel as displayed in the following figure. The gasket on the assembly should touch the panel s front surface once it is fully inserted. Inserting Assembly in Panel 10 IC755ACC07ADP Installation Guide GFK-2895A

11 Verify that the rear of the assembly displays as illustrated in the following figures. The various ports must be oriented with the SD, MIC, and such ports on the left, and the COM, +24 V power, LAN, and such ports on the bottom. Installed Assembly Rear View Installed Assembly Underside Rear View GFK-2895A IC755ACC07ADP Installation Guide 11

12 7. Prior to attaching any clamps to the adapter, insert the flat head slotted screws into each of the four adapter mounting clamps. Clamp Threaded PEM insert Slotted screws (Qty 2 per clamp) Mounting Clamp Run the screws into the PEM inserts until the taper on the screw head contacts the insert. This promotes clearance between the screw and the panel. PEM Insert with Screw 12 IC755ACC07ADP Installation Guide GFK-2895A

13 8. Using the provided slots, insert the four mounting clamp assemblies into the adapter. Insert the hooks of each mounting clamp into the adapter openings as displayed in the following figures. Inserting Mounting Clamps into Adapter Mounting Clamp Hooks GFK-2895A IC755ACC07ADP Installation Guide 13

14 When the adapter brackets are installed, the completed assembly displays as follows. QuickPanel+ 7 Display adapter Assembly Fully Seated in Panel 9. Using a slotted screwdriver, tighten the clamp screws against the rear panel surface to a maximum torque of 0.23 to 0.45 Nm (2 to 4 in-lb). Note: Screws should be tightened applying a uniform pressure to the adapter gasket against the front panel surface. Mounting clamps hold the unit in place by tension; no drilling is required. 10. Reconnect any cables that were removed in step 1 of this procedure. If an SD card was removed, install it in the SD port. 14 IC755ACC07ADP Installation Guide GFK-2895A

15 GE Intelligent Platforms Contact Information Americas: or Global regional phone numbers are available at GE Intelligent Platforms, Inc. All Rights Reserved *Trademark of GE Intelligent Platforms, Inc. All other brands or names are property of their respective holders. GFK-2895A