Specifiying in 5 easy steps

Transcription

1 RS- led Panels and Load Centers Motorized reakers Make Easy! ll relay based systems MUST be electrically protected by a circuit breaker. Motorized breakers eliminate the need for wall or rack mounted relay based systems Saves Space Saves redundant installation and hardware costs! UL listed circuit breaker with builtin internal switching capability manufactured by Time tested, in service over 0 years vailable in, 0 and 0 -, or poles for remote control of all electrical loads Robust - rated for 60k on, off, on cycles Energy efficient - O holding current or heat sinks required to maintain state - Runs cool, lasts long! utomatic load shedding and brownout protection in every panel. Emergency override funtion standard on every panel. Specifiying in easy steps. Choose the control method: SC=RS-. Choose the cabinet style: LC for load center and P for panelboard. Choose three phase () or single phase (). Choose the number of circuits: 6 or Panelboards are only available in circuits.. Choose the maximum number of controlled circuits: 0,0, 0, 0, or 0. EX: SCLC 6-0 = a phase load center with 6 circuits ( max controlled) SCP -0 = a phase panel board with circuits (0 max controlled) ll panels and load centers

2 SCLC 6-xx-Mxxx RS- led Load Center Ø, 08Y/0 Vac, wire. 00 mp Main reaker Standard RS- led Load Center MODEL UMERS SCLC 6-0-Mxxx (Up to 0 RS- controlled circuits) SCLC 6-0-Mxxx (Up to 0 RS- controlled circuits) SCLC 6-0-Mxxx (Up to 6 RS- controlled circuits) Square D QO7M00 Load Center with low-voltage sidecar. Standard back-fed Main reaker: Squared D# QO00VH. 00, (VH = k IR) [mps Interrupt Rating] ack-fed Main reaker options Part# suffix old face=mps -M00, -M00: (0kIR) Square D# QO0xx -M00, -M060, -M070 or -M090 Squared D# QOxxVH (all VH = k IR) Wire Sizes # - /0 Cu Outside dimensions 0.9" w., 9.8" h.,.9" d. RS- led Panelboard MODEL UMERS SCP -0-Mxxx (Up to 0 RS- controlled circuits) SCP -0-Mxxx (Up to 0 RS- controlled circuits) SCP -0-Mxxx (Up to 0 RS- controlled circuits) SCP -0-Mxxx (Up to 0 RS- controlled circuits) SCP -0-Mxxx (Up to RS- controlled circuits - limited by circuit code rule) Square D QOD-L M Panel with low-voltage sidecar. Standard SCP- Main reaker: mp. - 6k IR - MJG6 Main reaker options Part# suffix old face = mps -MHG, -MJG0, -MJG7 or -MJG00 Wire Sizes Main reaker: /0-0 kcmil l/cu 00% eutral has one feed lug that accepts - 0 kcmil Cu wires SCP -xx-mxxx RS- led Panelboard Ø, 08Y/0 Vac, wire. mp Main reaker Standard VILLE MODELS See for model specific design and submittal PDFs Cabinet Outline Surface mount only High voltage interior may be field inverted for top feed Copper us Enclosure ground bar. position - ga. Copper us S / MI C RS- COTROL POWER 0 supplied installed Main Lug Only -MLO option Remove ack fed main and top feed as a MLO to gain circuits. Feed from a protected disconnect. Provides access to branch breaker positions,, &. Model number becomes a SCLC 9-0-MLO (0 RS- controlled circuits) SCLC 9-0-MLO (0 RS- controlled circuits) SCLC 9-0-MLO (Up to 9 RS- controlled circuits) (Holds up to 9 one pole breakers) mp. Panel us Rating Wire size: #6 - /0 Cu Cabinet Outline Surface mount only MI X C QOD-L Panel 00% eutral Outside dimensions 8.06" w., 0" h., 6." d. RS- COTROL POWER 0 supplied installed Knockout panels supplied in both ends Optional isolated technical ground sidecar not shown LOD CETERS S / PELORDS eps SCLC -xx-mxxx RS- led Load Center Ø, 08Y/0 Vac, wire. mp Main reaker Standard RS- led Load Center MODEL UMERS SCLC -0-Mxxx (Up to 0 RS- controlled circuits) SCLC -0-Mxxx (Up to 0 RS- controlled circuits) SCLC -0-Mxxx (Up to 0 RS- controlled circuits) SCLC -0-Mxxx (Up to 0 RS- controlled circuits) Square D QOMQ Load Center with low-voltage sidecar. Standard Main reaker: Square D# QDL. mp Main reaker options Part# suffix old face=mps -M0 or -M00 Square D# QDLxxx series (all k IR) [mps Interrupt Rating] Wire Sizes Main reaker : 0 kcmil l or 0 kcmil Cu. 00% eutral has one feed lug - 0 kcmil l or - 0 kcmil Cu Outside dimensions 0.9" w., 9." h.,.9" d SCP -xx-m00 RS- led Panelboard Ø, 08Y/0 Vac, wire. 00 mp Main reaker Standard RS- led Panelboard MODEL UMERS SCP -0-M00 (Up to 0 RS- controlled circuits) SCP -0-M00 (Up to 0 RS- controlled circuits) SCP -0-M00 (Up to 0 RS- controlled circuits) SCP -0-M00 (Up to 0 RS- controlled circuits) SCP -0-M00 (Up to RS- controlled circuits - limited by circuit code rule) Square D QOD M Panel with low-voltage sidecar. Standard SCP 00 Main reaker: 00 mp. - 0k IR - L600 [mps Interrupt Rating] Wire Sizes Main reaker: #- 600 kcmil Cu or - #-0 kcmil Cu (per EC) 00% eutral has one feed lug that accepts one #-70 kcmil or two #-00 kcmil Cu wires. Outside dimensions: 8.06" w., 68." h., 6." d. Optional isolated technical ground Cabinet Outline Surface mount only Cabinet Outline Surface mount only S / High voltage interior may be field inverted for top feed Enclosure ground bar. position - ga. Copper us C MI ll Panels RS- COTROL POWER 0 supplied installed 00 Copper us MI S / C S / QOD Panel 00% eutral RS- COTROL POWER 0 supplied installed

3 RCHITECT'S and EGIEER'S SPECIFICTIOS SCP Series Serial led Panelboard ll.c. power for the /V system shall be supplied from a source capable of being remote controlled via RS- control protocol. Circuits shall be individually addressable providing on and off control via RS protocol. means of visual operator feedback shall provide an indication of circuit on/off status locally via LEDs. The system shall have brownout (undervoltage) protection; monitoring the line voltage and triggering an automatic shutdown if the line voltage drops below 9 volts for more than seconds. The system shall automatically return circuits to on state when power resumes and remains above 0 volts for more than seconds without operator intervention. The system shall have emergency shutdown capability triggered by external contacts or the system operator. Un-motorized circuits, as required, shall be supplied from the same.c. source so that a single lever main circuit breaker is dedicated to the system. Three phase panelboards shall have 00% neutrals. Single phase panelboards shall have a single neutral. Panelboards shall have a separate and attached isolated technical ground section. ll branch circuit breakers shall be bolt-on. The Serial led Panelboard system shall be the model SCP xxx series Panelboard. Manufacturer shall warrant specified equipment to be free from defects in materials and workmanship as follows: at least () months from date of purchase for line voltage equipment; at least () years from the date of purchase for control electronics Models: Single Phase, 6k IR: SCP -, SCP -, SCP -6, SCP -8, SCP -60 alanced Power, 60v-0-60v, 6k IR: SCP 9-, SCP 9- Three Phase, 6k IR: SCP -, SCP -, SCP -6, SCP -8, SCP -60 This document available in Word format: Most recent version pdf: _SCP_&E_Spec 0//

4 SC-0 RS PROTOCOL Commands set Command Decimal Hexadecimal Start byte 76 0x0 Stop byte 0 0xF0 address x0 0x6 Output address - 0 0x0 0x0 Output O 80 0x Output OFF 8 0x Output status 8 0x6 Status of all outputs 89 0xD ll O 86 0x ll OFF 87 0x Set/clear output verification status* 90 0xE *ot be implemented autoscan can distinguish between RR7 and RR9. Commands description. Outputs O command 0x0, board_address, 0x, output_address_,, output_address_m, 0xF0 m<=0 (0x0) Example: F0, turns on outputs at and 0, on st card. Outputs OFF command 0x0, board_address, 0x, output_address_,, output_address_n, 0xF0 n<=0 (0x0) Example: F0, turns off output at 9, on nd card. Outputs O/OFF command 0x0, board_address, 0x, output_address_,, output_address_m, 0x, output_address_,, output_ address_n, 0xF0 m and n<=0 (0x0) Example: F0, turns on output at and 0, and turns off output at 9, on st card. Outputs status 0x0, board_address, 0x6, output_address_,, output_address_m, 0xF0 m<=0 (0x0) Example: F0, status of outputs at and 0, on rd card. Status of all outputs 0x0, board_address, 0xD, 0xF0.6 ll O - turn on all available outputs 0x0, board_address, 0x, 0xF SC-0 Program Card

5 .7 ll OFF - turn off all available outputs 0x0, board_address, 0x, 0xF0.8 Set/clear output verification status (OT IMPLEMETED) 0x0, board_address, 0xE, output_address_i, output_ver_status_i, output_address_j, output_ver_status_j,, output_address_n, output_ver_status_n, 0xF0 output_address_i, output_ver_status_i, output_address_j, output_ver_status_j,, output_address_n, output_ ver_status_n addresses and status of outputs, n<=0 Output_ver_status coding Status Disable Enable Code 0x0 0x0 When verification status of the output is disabled, the board will always respond with no verification status for this output. Verification status shall be disabled for all outputs driving RR7 relays.. Responses. Output status codes Status Off On Fault o verification, expected off o verification, expected on Empty Code 0x0 0x0 0x0 0x0 0x0 0x06. Output status change response This response is transmitted when output(s) change(s) status for Y reason (RS command, button push, brown out, recover from brown out, emergency override, recover from emergency override). 0x0, board_address, 0x6, output_address_i, output_status_i,, output_address_n, output_status_n, 0xF0 n<=0 (0x0) Example: F0, output at is off, at is on, and at 0 is empty, on st card. Status of all ten outputs (transmitted only in reply to status of all outputs command) 0x0, board_address, 0xD, byte_,, byte_0, 0xF0 Example: 0 0 D F0, outputs thru are off, 6 thru 9 are on, and 0 is empty, on nd card. MX Device Discovery eacon request: MX\r eacon: "MX<-SDKClass=Utility><-Make=Lyntec><-Model=SC0><-Revision=.0.0>\r" SC-0 Program Card

6 Planning and Layout Worksheet s-built door label SCP 8-xx- RS- led Panelboard reaker types, sizes, positions and connections Transfer as-built information to the door label upon completion. Keep this sheet for as-built documentation vailable as PDF download SCP 8-xx (6k IR main) - bus xx = umber of controller circuits 0, 0, 0, 0 or 0. Cabinet outline - Surface mount only Outside dimensions: 8.06" w., 0" h., 6." d. Knockout panels supplied in both ends. High voltage interior may be field inverted for top feed. MI /0 max. MI C X RS- COTROL POWER QOD-L Panels 00% eutrals -0 kcmil max. Square D QOD-L Panel with sidecars. Standard back-fed Main reaker: QO00VH. 00, (VH = k IR). [mps Interrupt Rating] Main Options: -M00, -M0: 0kIR QO0xx -M00, -M060, -M070 or -M090 mps QOxxVH (all k IR) Wire: # - /0 kcmil Cu. Document # _SCP8 Planner 09/8/ Each motorized breaker is actuated by a command from a RS- control device. s-built door label example: The RS- # is the RS- address of this breaker. The board jumpers set the RS- address of the board. Each breaker has a sub-address of -0 old line around box = suggested control board: # (Top), #, # or #. Fill in box to indicate which control board this breaker is connected to Phase Phase Phase C C C C C C MI 8 mp. ^ Un-motorized. ^ Motorized-RS- # 9 mp. ^ Un-motorized. ^ Motorized-RS- # C RS- COTROL POWER 0 un-motorized breaker supplied installed. Job Panel Comments by Date 6 8 Which board? RS- Input SC-0 circuit boards in left-hand, low-voltage cabinet. RS- board address: RS- board address: RS- board address: RS- board address: RS- board address: VC input board model SCP 8-0 Lighting Panelboard 8-0 model holds up to poles. s up to 0,, or pole breakers. RS- Output board model SCP 8-0 Lighting Panelboard 8-0 model holds up to poles. s up to 0,, or pole breakers. board model SCP 8-0 Lighting Panelboard 8-0 model holds up to poles. s up to 0,, or pole breakers. board model SCP 8-0 Lighting Panelboard 8-0 model holds up to poles. s up to 0,, or pole breakers. board model SCP 8-0

7 Outline Drawing 8.06".00" 8.0".8" 6." ler High voltage interior may be field inverted for top feed SCP 8-xx Ø, 08Y/0 Vac, wire. 00 mp back-fed Main, (all k IR) Surface mount only Square D QOD-L Panel with sidecars. Standard back-fed Main reaker: QO00VH. 00, (VH = k IR). [mps Interrupt Rating] Main Options: -M00, -M0: 0kIR QO0xx -M00, -M060, -M070 or -M090 mps QOxxVH (all k IR) Wire: # - /0 kcmil Cu. ler ler ler ler C back-fed MI /0 max. C Enclosure ground bar. position, - ga. X ler POWER QOD-L Panel 00% eutrals. 0 kcmil max.." I.D. wiring access nipples between sidecars & Panelboard.00".00" 0.00" Outside Dimensions 6" w., 0" h., 6." d SCP8 Outline Drawing 09/8/

8 Outline Drawing with optional ITG sidecar.00".00" C/L 8.0".00" ler High voltage interior may be field inverted for top feed Isolated Technical Ground ar SCP 8-xx Ø, 08Y/0 Vac, wire. 00 mp back-fed Main, (all k IR) Surface mount only Square D QOD-L Panel with sidecars. Standard back-fed Main reaker: QO00VH. 00, (VH = k IR). [mps Interrupt Rating] Main Options: -M00, -M0: 0kIR QO0xx -M00, -M060, -M070 or -M090 mps QOxxVH (all k IR) Wire: # - /0 kcmil Cu. ler ler ler ler C back-fed MI /0 max. C Enclosure ground bar. position, - ga. X ler POWER QOD-L Panel 00% eutrals. 0 kcmil max. Feed /0 max. Feed /0 max. Iso-Tech Ground ranches: 6 position - ga.." I.D. wiring access nipples between sidecars & Panelboard.00".00" 0.00" Outside Dimensions 6" w., 0" h., 6." d. 6." 6.00" SCP8 ITG Outline Drawing 09/8/

9 For the most up-to-date information Selection Information H- and J- frame Thermal-magnetic Molded Case 0 and 0 mpere Frame Class 6 0 H-frame LCP-xx. MSP -xx, SCP, & RPC Main breaker suffix -MHG0 = 0 * -MHG = *Special Order Option CR on Cancellable on Returnable 0 J-frame LCP -xx. MSP -xx SCP -xx, & RPC The standard main breaker is a JGP6 and requires no suffix number. Main breaker suffix options -MJG0 = 0 -MJG7 = 7 -MJG00 = 00 -MJG = } Circuit reaker Type HD HG HJ HL JD JG JJ JL umber of Poles,,,,,,,, Current Range Interrupting Ratings 0 V UL/ 80Y/77 Vac CS/ OM 80 Vac /60 Hz 600Y/7 Vac Vac DC /0 Vdc Ratings 00 Vdc TD TD TD TD TD TD TD TD 0/0 Vac / 6/6 00/00 / / 6/6 00/00 / IEC 97- Icu/Ics 80/ Vac 8/8 / 6/6 00/00 8/8 / 6/6 00/00 00/ Vac / 8/8 / 0/0 / 8/8 / 0/0 Special Ratings Fed. Specs W-C-7/GE HCR (, -pole) Connections/Terminations Unit Mount I-Line Rear Connection Drawout Optional Lugs Unit Mount ccessories and Modifications Shunt Trip Undervoltage Trip uxiliary Switches larm Switch Motor Operator Handle Operators Handle Padlock ttachment Handle Mechanical Interlocks Optional GF Protection Trip System Type Thermal-magnetic Instantaneous-only (MCP) Molded Case Switch (utomatic) Electronic Dimensions Height I (mm) Dimensions (P Unit Width I (mm) Mount) Depth I (mm) ot available in HD and HG two-pole rating (-pole module) -pole in a -pole module. /0/0 6. (6). (0). (86) 7. (9). (0). (86) For ranch reaker Series Ratings see CIRCUIT REKERS 6 00 Schneider Electric ll Rights Reserved /0/0 overprint _H_J_Frame_Mains.pdf 09/8/ from Digest 7 page 6-

10 Series Ratings For QOD and F Panelboards Class 60, For the most up-to-date information 8 PELORDS This page contains UL Tested and Certified series combination ratings for panelboards. These ratings apply to either an integral main located in the same enclosure or a remote main located in a separate enclosure. QOD Series Ratings QOD Series Ratings (Continued) Maximum System Voltage C c 0 8- Maximum Short Circuit Current Rating (RMS Symmetrical) Integral or Remote Main Circuit reakers and Remote Main Fuses LC 600 Maximum ranch Circuit reaker Designations and llowable mpere Ranges ab Type -pole -pole -pole k MG QO () / k HD, JD QO () PL k HG, JG QO () PL Ø 00k HJ, JJ QO () PL k HL, JL QO () PL QO () DJ 00 QO () GFI / QO () VH QO () FI Ø 00k QO () Y/ QO () S QJ QO () GFI QO () PL QO () VH QO () FI models } L/LH (L) 00MC 08Y/ 0 8k L/LH (L) MC LCLC 6 L/LH (L) 0MC QO () MSLC 6 L/LH (L) 00MC SCLC 6 UM-xx QO () QO () S MSLC 8 k QO () VH QO () GFI SCLC 8 M-xx QO () PL QO () FI MSP 8 SCP 8 QO () k Q-Hf QO () GFI MSP9 QO () FI UM-xx QO () 70 0 QO () S models k QD QO () GFI LCLC M-xx QO () PL QO () VH MSLC QO () FI SCLC } QO () k ED, FDf QO () GFI QO () FI QO () k KDf QO () S QO () GFI QO () FI models QO () MSLC QO () VH MSLC 7 k HD, JD QO () GFI QO () FI MSLC 9 QO () H are series QO0VH rated k L, M QL-Hf IR. QDL k see MG QO () VH QO0Mxx HD, JD QO () PL on pg - QO () 70 d of Digest QO () VH 0 00 k (P 08 V Max.) QO () GFI 0 e QO () FI models MSP 9 MSP SCP LCP MSP SCP } { 6k 6k 6k 6k 6k 6k 6k DJ 00 EG, FGf, KGf QG M-xx QG, HG, JG UM-xx HG, JG QO () VH 0 00 (P 08 V Max.) QO () GFI 0 e QO () FI QO () QO () VH QO () H QO () QO () GFI QO () FI QO () 70 0 QO () S QO () VH QO () GFI QO () PL QO () FI QO () QO () VH QO () H QO0VH FCL QO () KCL QO () S FCL QO () GFI KCL QO () FI Max. Class J or T6 Fuses QO () VH 0 00 QO-VH QO () FI FCL QO () k KCL FCL QO () S QO () GFI KCL QO () FI k 00 Max. Class T Fuses QO () FI QO () k EJ, FJf QO () GFI QO () FI QOxxx () = UM series olt-on, UnMotorized reaker -xxx = poles. xxx = trip current. [ pole] UM-, UM-0, UM-0 [ pole] UM-, UM-0, UM-0 [ pole] UM-, UM-0, UM-0 QOxxx = UM series clip-on, UnMotorized reaker -xxx = poles. xxx = trip current. [ pole] UM-, UM-0, UM-0 [ pole] UM-, UM-0, UM-0 [ pole] UM-, UM-0, UM-0 ll & 0 breakers are HM (High Magnetic) Maximum System Voltage C c 0 00k HJ, JJ k HL. JL 00k FI, KI 00k Suffixes HID, SWD and SW may also be applied to the applicable branch circuit breakers shown above, except suffix SW may OT be applied in combination with LC main circuit breakers. Where QO () circuit breakers are shown above, QO () H, QO () VH, and QH () circuit breakers may also be used. For shown circuit breakers rated less than this maximum voltage, the indicated short circuit current rating also applies, but at the voltage rating of the circuit breaker. Only 0 circuit breakers may be used when the LC circuit breaker is rated 0, 00 or 600. Circuit breakers may not be used when the LC circuit breaker is rated 0, 00 or 600. Obsolescent. Contact your nearest Square D/Schneider Electric sales office for replacement circuit breaker. One-pole FJ circuit breakers are still available. Where QO() GFI circuit breakers are shown above, QO(), EPD circuit breakers may also be used. 00, Y/7 00,000 { 8//06 Maximum Fuses 00 Class J or T6 00 Class T F Series Ratings Maximum System Voltage C Maximum Short Circuit Current Rating (RMS Symmetrical) QO () QO () VH QO () GFI QO () PL QO () FI QO () H QO0VH QO () QO () S QO () GFI QO () FI QO () QO () S QO () GFI Main Type ranch Type Poles EG, FH, FGf, KH, LH, MH, MX, HG, JG ED, ED-EPD 6,000 EG EC-G 00,000 EJ, FC, FJf, KC, LC, LX, HJ, JJ EG 0 EJ, FC, KC, HJ, JJ EC-G,000 HL, JL EG, EC-G 00,000 FI, KI, LI, LXI EG, EJ FI, KI EC-G EG, FGf, KH, LH, HG, JG ED, ED-EPD,000 EG, HG, JG EC-G 6,000 EJ, FC, FJf, KC, LC, LX, HJ, JJ EG 80Y/77 EJ, FC, KC, HJ, JJ EC-G 00,000 HL,JL EG 00,000 FI, KI, LI, LXI EG, EJ FI, KI EC-G 600Y/7 Maximum Short Circuit Current Rating (RMS Symmetrical) 8,000 HG, JG, MG,000 LH,000 LC, LE 0,000 HL, JL ED, ED-EPD EJ, FI, KH, KL, LC,. LE, LX, LI, LXI, HJ, JJ EG ED( 70 ), EG EG, EJ EG, &, &,, 6,000 FI, KI EG, EJ LI, XI EJ Remote Main Fuse 0 00, mpere Maximum Class J or T (600V) EC-G, & 00,000 80Y/77 00,000 Integral or Remote Main Circuit reakers and Remote Main Fuses 00 mpere Maximum Class J or T (600V) 00 mpere Maximum Class J or T (600V) 00 mpere Maximum Class J or T (600V) 00 mpere Maximum Class J or T (600V) ranch Circuit reaker Designations and llowable mpere Ranges ab Type -pole -pole -pole EG, EJ EG, EJ EC-G EG, EJ, &, & QOPLxxx-9 = M series olt-on, Motorized. (REMOTELY OPERTED) -xxx = poles. xxx = trip current. -9 suffix denotes special 60" control wires. [ pole] M-, M-0, M-0 [ pole] M-, M-0, M-0, M-0, M-0, M-60 [ pole] M-, M-0, M-0 QOPLxxx-9 = M series clip-on, Motorized. (REMOTELY OPERTED) -xxx = poles. xxx = trip current. -9 suffix denotes special 60" control wires. [ pole] M-, M-0, M-0 [ pole] M-, M-0, M-0, M-0, M-0, M-60 [ pole] M-, M-0, M-0 overprint: Series Ratings 09/7/ For most current version see Schneider Electric ll Rights Reserved 8//06

11 Instruction ulletin REQUIREMETS overprint document # /00 Cedar Rapids, I, US EC QO-PL (Plug-on), QO-PL (olt-on) Powerlink Remotely Operated Circuit reakers (Use in Type QO Load Centers and Type QO, QO, and QOD Panelboards) Retain for future use. Remotely Operated Circuit Requirements DGER HZRD OF ELECTRIC SHOCK, UR, OR EXPLOSIO. When servicing a branch circuit fed by a remotely operated circuit breaker, move handle of remotely operated circuit breaker to OFF position. Do not rely on remote operation to open circuit breaker. POWERLIK QO()-PL Remotely Operated Circuit reakers require a power supply capable of delivering at least two amperes at Vdc for a minimum of 0 milliseconds. One-, two-, and three-pole circuit breakers all have one internal motor, and power requirements are the same regardless of the number of poles and ampere ratings. The required power supply ampacity and control device contact rating are determined by the number of circuit breakers to be switched simultaneously (i.e., four circuit breakers switched simultaneously require a power supply and a control device contact rated 8 amperes minimum). The control device may be either a normally-open (O)/ normally-closed (C) contact; a single-pole, double-throw switch (SPDT); or other three-wire control device. Failure to follow these instructions will result in personal injury or death. CIRCUIT REKER ISTLLTIO DGER HZRD OF ELECTRIC SHOCK, EXPLOSIO, OR RC FLSH pply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See FP 70E. This equipment must be installed and serviced only by qualified electrical personnel. Turn off all power supplying this equipment before working on or inside equipment. lways use a properly rated voltage sensing device to confirm power is off. Replace all devices, doors, and covers before turning on power to this equipment. Failure to follow these instructions will result in death, or serious injury. See page for part number explanation. Turn off all power supplying this equipment before working on or inside equipment... efore installing circuit breaker turn circuit breaker handle to OFF position. Remove panelboard cover and deadfront. Verify power is off with voltage meter before proceeding. Installation of circuit breaker into panelboard/load center (refer to figure below) PL Except for remotely operated connections, QO()-PL remotely operated circuit breakers are installed in a panelboard/load center the same as conventional QO() circuit breakers. Connection of remotely operated circuit (refer to the figure on next page). Plug-on or olt-on Connector 0 C us ar Connector(s) VISI-TRIP Indicator Wire inding Screw Mounting Clip Mounting Rail Load Wire lack White Red Wires ssure that power supply and control device meet requirements listed under "Remotely Operated Circuit Requirements." ll supplied breakers have special 60 control wires. (Square D standards are 8.)

12 QO-PL (Plug-on), QO-PL (olt-on) POWERLIK Remotely Operated Circuit reakers Instruction ulletin /00 CIRCUIT REKER ISTLLTIO CUTIO HZRD OF CIRCUIT REKER DMGE. Connect the Vdc remote control wiring as shown on this page. Failure to follow these instructions can permanently damage the remotely operated circuit breaker. part numbers M series motorized circuit breakers (Snap-On) May be used in LCLC, LCP, MSLC, MSP, SLC or SP series panels. M series motorized circuit breakers (olt-on) Use only in LCP, MSP or SP Panelboards ll M & M series breakers have Square D part number suffix of -9 indicating a special 60 inch lead length for remote control wires required to connect to control boards in low voltage cabinet. ** = Stocked items **M- = mp. Square D QO-PL-9 **M- = mp. Square D QO-PL-9 **M-0 = 0 mp. Square D QO-0PL-9 **M-0 = 0 mp. Square D QO-0PL-9 **M-0 = 0 mp. Square D QO-0PL-9 **M-0 = 0 mp. Square D QO-0PL-9 Two pole motorized - call for pricing & delivery M- = mp. Square D QO-PL-9 M- = mp. Square D QO-PL-9 **M-0 = 0 mp. Square D QO-0PL-9 **M-0 = 0 mp. Square D QO-0PL-9 M-0 = 0 mp. Square D QO-0PL-9 M-0 = 0 mp. Square D QO-0PL-9 0, 0 or 60, Two pole also available on Special Order Three pole motorized - call for pricing & delivery M- = mp. Square D QO-PL-9 M- = mp. Square D QO-PL-9 M-0 = 0 mp. Square D QO-0PL-9 M-0 = 0 mp. Square D QO-0PL-9 M-0 = 0 mp. Square D QO-0PL-9 M-0 = 0 mp. Square D QO-0PL-9 also stocks UM & UM (un-motorized) QO series circuit breakers including HM (High Magnetic). Recommended for eliminating nuisance trips in high inrush applications. [ ll M & M-x's and M & M-x0's are HM breakers.] Melrose Dr., Lenexa, KS 66, US Voice 9-9- Fax or overprint //06 6. ll wiring and splicing must comply with applicable code requirements for Class circuits. Refer to paragraph 7-8 and article 7 of the ational Electrical Code. 7. Three #8 WG control wires are attached to the remotely operated circuit breaker for connection to the power supply and remote control device and should be cut to the required length to reach the splice connections. Use #8 WG or larger conductors with 600 V insulation and approved wire connectors for splices. 8. Connect the black lead of the remotely operated circuit breaker to the negative (-) terminal of the Vdc power supply. Connect the red lead of the remotely operated circuit breaker to the positive (+) terminal of the Vdc power supply. Connect the white lead of the remote control device. The remote control device provides connections between either positive or negative potential of the power supply and the white wire of the remotely operated circuit breaker, as appropriate. 9. pplying the positive potential of the power supply to the white wire (contact closure between the red wire and white wire) will operate the remote mechanism of the circuit breaker to the OFF position. pplying the negative potential of the power supply to the white wire (contact closure between the black wire and the white wire) will operate the remote mechanism of the circuit breaker to the O position. control circuit utilizing a normally open (O)/normally closed (C) contact is illustrated below. OTE: The remote mechanism will not move the circuit breaker handle. lso, the remote mechanism cannot turn power O when the circuit breaker is tripped (VISI-TRIP flag indicator showing) or when the circuit breaker handle is in the OFF position. Installation of the trim and operational checks 0. Remove corresponding twist-out from panelboard trim and replace trim.. Turn power to panelboard on.. Turn remotely operated circuit breaker handle to the O position.. Turn power to the remotely operated circuit on and test this circuit, turning remotely operated circuit breaker off remotely, then on remotely. If power to remote controlled circuit breaker load does not switch off and on, turn off power to remotely operated circuit and panelboard and check wiring. PL00. OTE: power supply is available from Square D Company, Cat. o. QOPLPS (plug-on) or QOPLPS (bolt-on). Splice not normally required with supplied breakers with 60 leads. Remotely Operated Circuit reaker Panelboard/Load Center Splice Connection (Class Wiring) In Sequencer or DMX controller O lack O + Vdc Power Supply White Red C OFF Square D Company 700 Sixth Street SW Cedar Rapids I 0 US -888-SquareD ( ) Electrical equipment should be installed, operated, serviced and maintained only by qualified personnel. o responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material Schneider Electric ll Rights Reserved