KU series KUP Enclosed Relay KUIP VDE 8mm Coil to Contacts KUGP VDE 8mm 3mm Gap Coil to Contacts KUEP 10 Amp 150VDC Load Switching KUMP 15 Amp 277VAC

Transcription

1 KU series KUP Enclosed Relay KUIP VDE 8mm Coil to Contacts KUGP VDE 8mm 3mm Gap Coil to Contacts KUEP 10 mp 150VDC Load Switching KUMP 15 mp 2VC File E2255 File LR Registration 12 (KUIP) 0435 Registration 12 (KUGP) License Features C coils: -240VC, 50/0 Hz. DC: -110VDC. Contact arrangement up to 4PDT. Wide selection of termination and mounting styles. PC terminals available. Push to test button and indicator lamps. KUEP incorporates a blow out magnet for high voltage DC switching. KUIP/KUGP are VDE approved. Complete line of sockets and DIN rail. Class coil insulation. Contact 25 C rrangements: See respective ordering information table. Materials: Fine silver (5 amp) silver-cadmium oxide (10 amp). Gold flash available as standard. Gold diffused and gold alloy on special order. Expected Mechanical Life: Contact Ratings Material rrangement UL/CS Ratings Expected Life Fine ll 5 28VDC or 240VC Silver 80% PF, 2.5 amp 1/2 120VDC. 100,000 1/ 1/3 240VC, 5 FL, VC (FL covered by 30,000 operations). Silver- 1-2 Pole 10 28VDC or 240VC, Cadmium KUP 80% PF, 5 amp Oxide KUIP 120VC, 3 00VC, 1/2 amp 120VDC. 100,000 KUEP 1/3 120VC, 1/2 ll KUMP 240, 480, and 00VC, 10 FL VC, 5 FL, VC.(FL ratings covered by 30,000 operations) KUMP 15 2VC, 80% PF KUM KUMP 100,000 3 Pole 10 28VDC or 120VC, KUP 80% PF, 2/3 240VC, KUIP 80% PF 100,000 4 Pole 10 amp per pole not to exceed 30 amp 28VDC, 120VC, 80% PF, 2/3 240VC, 80% PF 100,000 KUEP SPST-NO VDC KUEP 2PST-NO 5 150VDC KUEP 2PDT 3 150VDC 100,000 (ll other C ratings apply KUEP.) Initial Dielectric Strength etween Open Contacts: 1,200V rms; KUGP, 3,500V rms. etween djacent Contacts: 2,200V rms. etween Contacts and Coil: 2,200V rms; KUGP, KUIP, 3,50V rms. Coil 25 C Voltage: to 110VDC and to 240VC. Nominal Coil Power: DC Coils: 1.2 Watts - KUP, KUIP, KUMP, 1-3 pole; KUEP, 1 pole. DC Coils: 1.8 Watts - KUP, 4 pole; KUEP, 2 pole; KUGP. C Coils: 2.0V - KUP, KUIP, 1-2 pole; KUEP, 1 pole. C Coils: 2.V - KUP, KUIP, 3 pole; KUEP, 2 pole; KUGP, KUMP. Coil Data DC Volts 1.2 Watt 1.8 Watt Nominal DC Ohms ± 10% Nom. I ma DC Ohms ± 10% Nom. I ma , , ,000 11,20 1 C Volts 2V 2.V Nominal DC Ohms ± 15% Nom. I ma DC Ohms ± 15% Nom. I ma , , , , Operate 25 C Must Operate Voltage: DC Coils: 5% of nominal voltage or less. C Coils: 85% of nominal voltage or less. Operating Time (Excluding ounce): 15 milliseconds, typical, at nominal voltage. Release Time (Excluding ounce): 10 milliseconds, typical, at nominal voltage. Environmental Data Temperature Range: Operating: Enclosed Relays: -45 C to maximum listed in table below. Open Relays: dd 15 C to maximum listed. Max C 45 C 50 C 55 C 0 C 5 C 80 C 5 C KUP C DC C DC 3-4 pole 4 pole 1-2 pole 1-3 pole KUIP C C DC 3 pole 1-2 pole 1-3 pole KUGP C DC 2 pole 2 pole KUEP C DC C DC 2 pole 2 pole 1 pole 1 pole KUMP C C DC 3 pole 1-2 pole 1-3 pole

2 Environmental Data (Continued) Maximum llowable mbient Temperature vs. Voltage (KU enclosed) Max. mbient Temp. C Watt DC Coil 1.2 Watt DC Coil % of Nominal Voltage DC Max. mbient Temp. C V 0 Hz. COIL 2. V 0 Hz. COIL % Of Nominal 0 Hz. Voltage Mechanical Data Termination: Quick connect, solder and PC board. Enclosure: Clear polycarbonate dust cover. Weight: 3.0 oz. (85g) approximately. Ordering Information Typical Part No. KU F asic Series & Type: KUP KU = asic open relay. KUP = asic enclosed relay. 2. Contact rrangement: 1 = 1 (SPST-NO) = 1Z (SPDT-NC-NO [D-DM]) 13 = 3 (3PST-NC) 2 = 1 (SPST-NC) = 2 (DPST-NO) 14 = 3C (3PDT) 3 = 1 (SPST-NO-DM) 8 = 2 (DPST-NC) 15 = 4 (4PST-NO) 4 = 1Y (SPST-NC-D) 11 = 2C (DPDT) 1 = 4 (4PST-NC) 5 = 1C (SPDT) 12 = 3 (3PST-NO) 1 = 4C (4PDT) 3. Coil Input: = C 50/0 Hz. DS = Diode Suppression (DC coil only) D = DC 4. Mountings: Type KU KUP (through 3 poles) KUP (4 pole models) Codes 1,2,3,4,5,,,8, vailable 1,2,3,4,5,,C,D,E,F,G,H,T 1,3,5,,,,C,E,G OPEN STYLE 1 = PLIN CSE; = PLIN CSE, #-32 STUD LOCTING T; 1 = #-32 stud,.218" 2 = with test button. = with test button. (5.54mm) locating 3 = with indicator lamp.* C = with indicator lamp.* tab. 4 = with test button & indicator lamp.* D = with test button & indicator lamp.* 2 = 2-hole bracket, 5 = RCKET MOUNT CSE; E = PLIN CSE, TPPED CORE, LOCTING T; #-32 tapped. = with test button. F = with test button. 3 = #-32 tapped core, = with indicator lamp.* G = with indicator lamp.* " (3.18mm) 8 = with test button & indicator lamp.* H = with test button & indicator lamp.* locating tab. = STUD ON END OF PLIN CSE. T = TOP FLNGE CSE. 4 = #-32 tapped core,.218" (5.54mm) locating tab. 5 = #-32 tapped core, no locating tab. * Indicator lamps are available on models with the following coils: -24VC and DC, 110VDC and VC. Only models with VC coils are UL recognized. 5. Terminal & Contact Material: Type 1 & 2 Pole Models 3 Pole Models 4 Pole Models Codes 1,2,3,5, 1,2,3, 1**,3,4, **4 pole KUP with.18" (4.5mm) quick connect/solder vailable,,j,k 5,, 5**,, terminals will not plug into sockets. Must use.110" (2. mm) quick connect solder terminals for socket mounting. 1 =.18" (4.5mm) quick-connect/solder; silver, 5 amps. 2 =.205" (5.21mm) quick connect/solder; silver, 5 amps. =.04 (1.1mm) printed circuit; silver-cadmium 3 =.04" (1.1mm) printed circuit; silver, 5 amps. oxide, 10 amps. 4 =.110" (2.mm) quick connect/solder; silver, 5 amps. = 4 pole KU, KUP:.110" (2.mm) quick connect/ 5 =.18" (4.5mm) quick connect/solder; silver- solder; silver-cadmium oxide, 10 amps. cadmium oxide, 10 amps. J =.250" (.35mm) quick connect; silver, 5 amps. =.205" (5.21mm) quick connect/solder; silver- K =.250" (.35mm) quick connect; silver-cadmium cadmium oxide, 10 amps. oxide, 10 amps. 5. Gold Flashed Contact Option: F = Optional gold flashing for silver and silver-cadmium oxide contacts.. Coil Voltage: To 240VC, 50/0 Hz. or 110VDC. (For 2VC, consult factory.) Stock Items The following items are normally maintained in stock for immediate delivery. KUP KUP KUP KUP KUP-5D15-12 KUP-5D15-24 KUP-5D55-12 KUP-5D55-24 KUP KUP KUP KUP KUP KUP KUP KUP KUP-11T5-120 KUP-11D11-24 KUP-11D15-5 KUP-11D15-12 KUP-11D15-24 KUP-11D KUP-11D35-24 KUP-11D55- KUP-11D55-12 KUP-11D55-24 KUP-11D55-48 KUP-11D KUP KUP KUP KUP KUP KUP KUP KUP KUP KUP KUP KUP-14D11-24 KUP-14D15- KUP-14D15-12 KUP-14D15-24 KUP-14D15-48 KUP-14D KUP-14D25-24 KUP-14D35-24 KUP-14D55-12 KUP-14D55-24 KUP KUP KUP-1D1-24 KUP-1D55-24

3 Ordering Information VDE pproved Design Typical Part No. KUIP asic Series & Type: KUGP KUIP = Enclosed relay designed for General VDE 0435.* KUGP = Enclosed relay with 3mm open contact spacing. (Form and Form arrangements only)* 2. Contact rrangement: 1 = 1 Form (SPST-NO) = 2 Form (DPST-NO) 2 = 1 Form (SPST-NC) 8 = 2 Form (DPST-NC) 3 = 1 Form (SPST-NO-DM) 11 = 2 Form C (DPDT)* 4 = 1 Form Y (SPST-NC-D) 12 = 3 Form (3PST-NO) 5 = 1 Form C (SPDT)* 13 = 3 Form (3PST-NC) = 1 Form Z (SPDT-NC-NO [D-DM]) 14 = 3 Form C (3PDT)* 3. Coil Input: = C, 50/0 Hz.* D = DC* 4. Mountings: 1 = PLIN CSE, SOCKET MOUNT.* T = TOP FLNGE CSE.* 5 = RCKET MOUNT CSE.* 5. Terminal & Contact Material: 1 =.18" (4.5mm) quick connect/solder; silver. 5 =.18" (4.5mm) quick connect/solder; silver-cadmium oxide.* 3 =.04" (1.1mm) printed circuit board; silver. =.04" (1.1mm) printed circuit board; silver-cadmium oxide.. Coil Voltage: To 240VC, 50/0 Hz. or 110VDC. (For 2VC, consult factory.)* See coil data tables. * Options included in VDE file. Stock Items The following items are normally maintained in stock for immediate delivery. KUGP-D55-24 KUIP KUIP-11D55-12 KUIP-11D55-24 KUIP KUIP-14D15-12 KUIP-14D15-24 Ordering Information High Voltage DC Switching Typical Part No. KUE asic Series & Type: KUEP KUE = Open relay with magnetic blow-outs. KUEP = Enclosed relay with magnetic blow-outs. 2. Contact rrangement: 3 = 1 (SPST-NO-DM) = 2 (DPST-NO) 11 = 2C (DPDT) 3. Coil Input: = C 50/0 Hz. D = DC 4. Mountings: Type KUE KUEP OPEN STYLE 1 = PLIN CSE; = PLIN CSE, #-32 STUD LOCTING T; 1 = #-32 stud,.218" 3 = with indicator lamp.* C = with indicator lamp.* (5.54mm) locating 5 = RCKET MOUNT CSE; E = PLIN CSE, TPPED CORE, LOCTING T; tab. = with indicator lamp.* G = with indicator lamp.* 2 = 2-hole bracket, = STUD ON END OF PLIN CSE. T = TOP FLNGE CSE. #-32 tapped. 3 = #-32 tapped core, " (3.18mm) locating tab. 4 = #-32 tapped core,.218" (5.54mm) locating tab. *Indicator lamps are available on models with the following coils: 5 = #-32 tapped core, -24VC and DC, 110VDC and VC. Only models with no locating tab VC coils are UL recognized. 5. Terminal & Contact Material: 5 =.18" (4.5mm) quick connect/solder; silver- =.04' (1.1mm) printed circuit; silver-cadmium-oxide. cadmium-oxide. =.205" (5.21mm) quick connect/solder; silvercadmium-oxide.. Coil Voltage: To 240VC, 50/0 Hz. or 110VDC. (For 2VC, consult factory.) Stock Items The following items are normally maintained in stock for immediate delivery. KUEP KUEP-3D KUEP-11D15-12 KUEP-3D15-12 KUEP-D15-24 KUEP-11D15-24 KUEP-3D15-24 KUEP

4 Ordering Information 15 mp Switching Typical Part No. KUM asic Series & Type: KUMP KUM = 15 amp open relay KUMP = 15 amp enclosed relay 2. Contact rrangement: 1 = 1 (SPST-NO) 2 = 1 (SPST-NC) 3 = 1 (SPST-NO-DM) 4 = 1Y (SPST-NC-D) 5 = 1C (SPDT) = 1Z (SPDT-NC-NO [D-DM]) = 2 (DPST-NO) 8 = 2 (DPST-NC) 11 = 2C (DPDT) 12 = 3 (3PST-NO) 13 = 3 (3PST-NC) 14 = 3C (3PDT) 3. Coil Input: = C, 50/0 Hz. D = DC 4. Mountings: Type KUM KUMP OPEN STYLE 1 = PLIN CSE; = PLIN CSE, #-32 STUD LOCTING T; 1 = #-32 stud,.218" 2 = with test button. = with test button. (5.54mm) locating 3 = with indicator lamp.* C = with indicator lamp.* tab. 4 = with test button & indicator lamp.* D = with test button & indicator lamp.* 2 = 2-hole bracket, 5 = RCKET MOUNT CSE; E = PLIN CSE, TPPED CORE, LOCTING T; #-32 tapped. = with test button. F = with test button. 3 = #-32 tapped core, = with indicator lamp.* G = with indicator lamp.* " (3.18mm) 8 = with test button & indicator lamp.* H = with test button & indicator lamp.* locating tab. = STUD ON END OF PLIN CSE. T = TOP FLNGE CSE. 4 = #-32 tapped core,.218" (5.54mm) locating tab. *Indicator lamps are available on models with the following coils: 5 = #-32 tapped core, -24VC and DC, 110VDC and VC. Only models with no locating tab VC coils are UL recognized. 5. Terminal & Contact Material: Type 1 & 2 Pole Models 3 Pole Models Codes,8,,G,8, vailable =.205" (5.21mm) quick connect/solder; silver-cadmium-oxide. 8 =.18" (4.5mm) quick connect/solder; silver-cadmium-oxide. =.04" (1.1mm) printed circuit; silver-cadmium-oxide. G =.250" (.35mm) quick connect; silver-cadmium-oxide. (Not available on 3 pole models.). Coil Voltage: To 240VC, 50/0 Hz. or 110VDC (For 2VC, consult factory.) Stock Items The following items are normally maintained in stock for immediate delivery. KUMP KUMP-11D18-12 KUMP KUMP-14D18-24 KUMP KUMP-11D18-24 KUMP KUMP KUMP-11D KUMP-14D18-12

5 Outline Dimensions Open Relays racket Type.1 (4.8).3 (1.0) Stud Type 1.43 (3.50) (2) #-32 THRED TPPED HOLES 2.43 M.* (1.2) 2.33 M.** (5.18) 2.2 M.*** (58.1) 2.2 M.* (5.) 2.11 M.** (55.14) 2 M.*** (53.8) (35.33) (5.54).05 (1.5) Enclosed Relays Plain Case.288 (.32).43 (11.10) 1.3 M.* (35.3) 1.2 M.** (32.8) 1.25 M.*** (31.8).18 (4.5) DI. PUSH-TO-TEST UTTON VILLE ON KUP, KUMP & KUIP/KUGP.3 (1.0).1 (4.1).031 REF. (.).10 M. (2.) #-32 THRED Is For Terminal Dimensions. See Terminal Drawings..150 T WIDTH (3.81) 2.2 M.* (5.) 2.11 M.** (55.14) 2 M.*** (53.8) 1.48 M. (3.2).031 REF. (.) M. (35.5) 1.8 M. (42.85).31 (.) Seated Heights For Open Relays 1.31" (35.33mm) for #-32 stud with.218" (5.54mm) locating tab. 1.52" (38.mm) for bracket with 2-# 32 tapped holes " (32.5mm) for #-32 tapped core with " (3.18mm) or.218" (5.54mm) locating tab. 2.04" (51.mm) for relay with printed circuit terminals. STUD TYPE also available with " (3.18mm) tab, as well as without stud and locating tab. Models without stud have core tapped #-32 THRED,.25" (.4mm) minimum depth. *Dimensions with.250" (.35mm) terminals. **Dimensions with.110" (2.mm) or.205"(5.21mm) terminals. ***Dimensions with.18" (4.5mm) terminals. Core and Stud Mount Cases 1.8 M. (4.) 1.0 M. (48.41) 1.8 M. (4.) 1.0 M. (48.41) Top Flange Case.08 TYP. (1.8).21 M. (5.5) M M. (38.5) M. Is For Terminal Dimensions. See Teminal Drawings ±.010 (34.8 ±.25) 1.13 ±.0 03 (43.51 ±.08) 1.8 ±.0 03 (50.52).130 (3.30) STUD with #-32 THRED or CORE TPPED # ±.010 (11.10 ±.25) 1.3 M.* (35.3) 1.2 M.** (32.8) 1.25 M.*** (31.8) Dimensions with.250" (.35mm) terminals. Dimensions with.110" (2.mm),.18" (4.5mm and.205" 5.21mm) terminals. *Dimensions with.250" (.35mm) terminals. **Dimensions with.110" (2.mm) or.205" (5.21mm) terminals ***Dimensions with.18" (4.5mm) terminals. Stud on End Case 1.43 M. (3.2) 1.4 M. (44.2).312 (.2) M. (5.10) racket Mount Case.18 TYP. (4.52).38 (.).085 M. (2.1) 1.8 M. (4.) 1.0 M. (48.41).25 TYP. (15.88).312 TYP. (.2) 2.0 M. (3.).08 R. TYP. (1.8) PUSH-TO-TEST UTTON VILLE ON KUP, KUMP & KUIP/KUGP M..5 (1.1) 1.40 M (28.5).0 (1.52) #-32 THRED.1 (4.1).35 (.53) (11.10) (3.50).0 (1.8) 1.8 M. (4.) 1.0 M. (48.41)

6 Outline Dimensions (Continued) Relay Front Diagrams Relays With 1-3 Pole Relays.250" (.35mm) Terminals 4 Pole Relays M M M M M M. Terminal Dimensions.110" (2.mm).205" (5.21mm).250" (.35mm) Quick ConnectQuick Connect Quick Connect HEDER Printed Circuit.10 (2.).035 (.8).311 REF. (.0).034 (.8) THICKNESS.032 (.81).110 (2.).280 (.11) HEDER (.24).31 REF. (8.03) THICKNESS.18 (4.5mm) Quick Connect.032 (.81).03 (2.3).035 (.8).205 ±.0 02 (5.21 ±.05).00 DI. (1.8) HEDER.134 (3.40).312 (.2).035 (.8).358 REF. (.0) THICKNESS.032 (0.81).250 ±.0 03 (.35 ±.08).305 (.5) (2.3) HEDER (.02).28 REF. (.81).032 THICKNESS (.81).04 (1.1).180 (4.5).18 ±.002 HEDER (4.5 ±.05) (.35) (1.8).281 REF. (.14).020 THICKNESS (.51) Note: ll drawings shown oversize. Wiring Diagrams *1 Form 1 Form C *2 Form *2 Form C 3 Form C 4 Form C *Recommended Load Polarity for Optimum rc Suppression. PC oard Layouts (ottom Views) 1 Form 3 Pole Models 4 Pole Models.0 DI. TYP. (1.3).0 DI. TYP. (1.3).20 (5.23).0 DI. TYP. (1.3).20 (5.23).85.2 (15.0).43 (11.10) (8.33).2 (15.0).340 (8.4).510 (12.5) (25.1).328 (8.33).10 (4.32).2 (15.0)

7 Sockets For KU Series Relays Through 3 Poles Socket Selection Table Stock items are boldfaced. For KUP, KUEP, KUGP, KUIP, and KUMP relays, through 3 poles, with.18" (4.5mm) quick connect termination. Socket Socket Termination Hold-Down Spring 2E043 Solder eyelet 20C228 or 20C254* 2E04 PC board,.144" (3.mm) terminals 20C228 or 20C254 2E0.18" (4.5mm) quick connect 20C228 or 20C254 2E121 Screw terminals 20C314 (2 per socket required) 2E305 PC board,.184" (4.mm) terminals 20C228 or 20C254 2E310 PC board,.24" (.2mm) terminals 20C228 or 20C254 2E3.18" (4.5mm) quick connect* 20C254 2E3 Wire wrap* 20C254 2E400 Solder eyelet** 20C254 2E452 Wire wrap 20C228 or 20C254 2E83 Screw terminals 20C318 * 20C228 held in place by socket hold-down screw where as 20C254 snaps onto socket. ** Snap-in mounting. DIN rail mounting. Hard Mount Sockets For Relays Through 3 Poles Nylon sockets with.18" (4.5mm) quick connect, solder, printed circuit, wire wrap or no terminals are available for KUEP, KUGP, KUIP, KUMP, and KUP relays, through 3 poles, with.18" (4.5mm) quick connect terminals. ll are rated 15 amps and UL recognized, File E5244 and CS certified File LR1534 (except 2E452, 10 amps). 2E043with solder eyelet terminals. 2E0with.18" (4.5mm) quick connect terminals. 2E452with.032" (.81mm) x.02" (1.5mm) x.25" (18.42mm) terminals for wire wrapping. Use 20 to 2 guage wire depending on type of wrapping system (34.80).15 DI. (4.1) 2 HOLES 1.50 (38.1) 1.35 (34.3) 1.8 ±.010 (42.85 ±.25).50 TYP. (12.) 2.03 (51.5).85 ±.010 (22.23 ±.25) 2E043 2E0 2E452.2 (.54) (31.5).250 (.35) (31.5).2 (.54).250 (.35).34 M. (8.4).34 M. (8.4) The 2E043, 2E0 and 2E452 use chassis cutout shown on this page (31.5).2 (.54).500 M. (12.) 2E04, 2E305, 2E310 Socket With Printed Circuit Terminals 2 HOLES.15 DI. (4.1) 1.30 (34.80) 1.50 (38.1).50 TYP. (12.) 1.8 ±.010 (42.85 ±.25) 2.03 (51.5).85 ±.010 (22.23 ±.25) Recommended Chassis Cutout For Hard Mount Sockets (2.) 4 PLCES.20 (.0) 1.35 (35.43).15 DI. 2 HOLES 1.8 (42.85) 1.20 (32.2).208 (5.28).2 (.54) Suggested Socket PC oard Layout.0 DI. (1.3).2 (15.0).00 TYP. (2.2).180 TYP. (4.5) TYP..43 (11.10).218 (5.54) 1.8 (42.85) 1.0 (2.33).328 (8.33).023 (.58) 2E04 HS TERMINLS.144" (3. mm) LONG. 2E305 HS TERMINLS.184" (4. mm) LONG. 2E310 HS TERMINLS.24" (.2 mm) LONG. Recommeded Chassis Cutout For Snap-In Sockets 1.20 (32.2) 1.35 (35.43) Recommended chassis thickness.031" (.mm) to.02" (1.5mm). Snap-In Sockets For Relays Through 3 Poles Nylon snap-in sockets with.18" (4.5mm) quick connect, solder, or wire wrap terminals are available for KUEP, KUGP, KUIP, KUMP, and KUP relays, through 3 poles, with.18" (4.5mm) quick connect terminals. Snap-in sockets reduce labor by eliminating time consuming screw or rivet mounting. Preassembled wiring harnesses may also be used as the sockets are designed to snap into the chassis from either front or back. ll are rated 15 amps and UL recognized, File E5244. The 2E3, 2E3 and 2E400 use chassis cutout shown on this page. 2E3with.18" (4.5mm) quick connect terminals. 2E3with.02" (1.5mm) x.032" (.81mm) terminals for wire wrapping. Use 20 to 2 guage wire depending on type of wrapping system. 2E400with solder eyelet terminals (34.3).3 (10.0) 1.20 (32.00).23 (.0).834 (21.18).032 (.81).020 (.51).05 TYP. (1.5).281 (.14)

8 Sockets For KU Series Relays Through 3 Poles (continued) 2E121 Screw Terminal Socket The 2E121 socket offers screw termination for KUEP, KUGP, KUIP, KUL, KUMP and KUP relays, through 3 poles, with.18" (4.5mm) quick connect terminals. This socket stacks on 1.00" (43.18mm) centers. When surface mounting, two #-32 screws of suitable length are required. When track mounting, two 2401 retainer clips (not shown) are required. The 2E121 is rated 15 amps and is UL recognized, File E5244, CS certified, File LR E83 Screw Terminal, Din Rail Snap-Mount Socket (use with mounting track 24110) The 2E83 DIN rail, snap-mount socket offers screw termination for KUEP, KUGP, KUIP, KUL, KUMP and KUP relays, through 3 poles, with.18" (4.5mm) quick connect terminals. This socket is constructed with a spring-loaded latch which allows it to be quickly snapped onto or removed from a top hat style mounting track. No special tools or extra hardware is required for installation. The 2E83 is UL rated 15 amps, 4V-0, File E5244 and CS rated 10 amps, File LR1534. Two 20C31 hold-down spring anchor clips are packaged with each socket..850 ±.010 (21.5 ±.25) 1.00 ±.010 (43.18 ±.25).315 MIN. (8.00).540 (13.2).85 M. (22.3) Terminal Location Top View (35.).315 (8.00).84 (24.).51 (14.50) Terminal Location Top View TYP (38.10) TYP. (4.1) 2.2 (.00) (5.01) M. (80.01) M. (3.83) 1.00 M. (48.2) #-32 SCREWS & CPTIVE WSHERS 8.0 (2.01) 1.45 (3.01) 1.3 (43.00) M3-5 SCREWS & CPTIVE WSHERS.0 (18.01) 8 Sockets For KU Series 4 Pole Relays Socket Selection Table Stock items are boldfaced. For 4 pole KUP relays with.110" (2.mm) quick connect termination. Socket Socket Termianation Hold-Down Spring 2E415.18" (4.5mm) quick connect 20C228 or 20C254 2E41 PC board 20C228 or 20C254 2E8* Screw terminals 20C254 * Use 40G432 insulator pad or customer supplied alternative. (See page 100.) Hard Mount Sockets For 4 Pole Relays 2E415with.18" (4.5mm) quick connect/solder terminals. 2E41with printed circuit terminals. See PC board layout at right. Note: Only 4 pole KUP relays with.110" (2.mm) quick connect terminals can be used with 4 pole hard mount sockets..15 ±.0 05 (4.1 ±.13) 2 HOLES 1.30 (34.80) 1.50 (38.1).50 TYP. (12.) 1.8 (42.85) 2.03 (51.).85.2 (.54).32 M. (8.1) W/QC TERMINLS Siemens Electromechanical Components, Inc. 00 Westpark Drive Peachtree City, G TYP. (1.52) (31.5).250 (.35).340 (8.4).41 M. (11.1) W/PC TERMINLS Suggested Socket PC oard Layout.0 DI. TYP. (1.3).510 (12.5) (25.1).328 (8.33).20 (5.23).10 (4.32) 2E415 uses same chassis cutout as 2E (15.0) Screw Terminal Socket For 4 Pole Relays 2E8 offers screw termination for 4 pole KUP relays with.110" (2.mm) quick connect/socket mount terminals. Rated 10 amps and is UL recognized, File E DI. (2) MTNG. HOLES 1.50 ±.010 (44.45 ±.254) 3.50 ±.030 (88. ±.2).250 ±.010 (.35 ±.254) ±.010 (5.15 ±.254) 2.50 ±.015 (. ±.381) #-32 SCREWS.150 M. (3.81).02 REF. (1.5).230 ±.030 (5.84 ±.2).0 M. (1.5) Specifications and availability subject to change without notice. 13C580 Printed in U.S.. IH/10-8