Datasheet SPD II 1 Surge Protectors for AC Power Distribution SPD II PV Surge Protectors for Photovoltaic Installations

Transcription

1 Datasheet SPD II 1 Surge Protectors for A Power Distribution SPD II PV Surge Protectors for Photovoltaic Installations Weidmuller s SPD II 1 series transient voltage surge protectors consist of a range of innovative, compact modules for the protection of low voltage A distribution systems or (PV models) for D photovoltaic installations. In A applications, the SPD II 1 would be installed downstream of the main circuit breaker and fuse(s), connected between each live conductor to be protected and ground. For multi-phase circuits, multiple modules are used with jumper options between ground terminals and permitting a single connection to ground. In photovoltaic applications, the SPD II 1 PV would typically be in a combiner enclosure protecting the D output and return conductor to ground. Voltage limiting technology is integrated, which differentiates between transient pulses and longer-lasting overvoltages. This circuitry eliminates the disadvantages of varistor devices (MOVs) which, in competitive products, may switch-on inadvertently in conditions where the supply voltage is not well-regulated. Weidmuller s hybrid arrester design ensures efficient MOV operation and hence conserves energy, maximizes the operating lifetime of the arrester and eliminates arcing when the thermal disconnect operates. Each module is a two-part construction, comprising a TS35 DINrail mountable base and a pluggable replaceable arrester, with each single-conductor assembly only 18mm wide. Products are specified by their working voltage level, or maximum continuous operating voltage (MOV) and each has a maximum surge current rating of 50kA. Base/arrester assemblies are available either with or without a remote signaling option and arresters are available as spare parts. Models for LV A distribution or photovoltaic installations Quick replacement with spare pluggable, replaceable arresters Nominal voltages up to 480VA (550V MOV) or 1200VD Maximum surge current (Imax) 50kA Remote status signaling option UL1449 Ed3 approved and SA equivalent No discharge path fuse needed (Type 2) Weidmuller, anada 10 Spy ourt Markham, Ontario L3R 5H6 Telephone: (800) Facsimile: (877) info1@weidmuller.ca Website: Weidmuller, Mexico Blvd. Hermanos Serdán 698, ol. San Rafael Oriente Puebla, Puebla, Mexico.P Telephone: Facsimile: clientes@weidmuller.com.mx Website: Weidmuller, United States 821 Southlake Blvd. Richmond, Virginia Telephone: (800) Facsimile: (804) info@weidmuller.com Website:

2 SPD II A Surge Protectors For transient voltage protection of single and multi-phase circuits, in the main electrical panel, downstream of the main circuit breaker, or in control panels. SPD II 0 150V/40kA SPD II 1 150V/40kA SPD II 1 R 150V/40kA SPD II 0 280V/40KA SPD II 1 280V/40KA SPD II 1 R 280V/40KA A Network 120 V, Single phase 230 V, Single phase onnection Mode 1 Pole, L-N or L-G. 1 Pole, L-N or L-G. Max. Operating Voltage (MOV) 150 VA 277 VA Leakage urrent at Uc <1mA <1mA Follow urrent None None UL 1449 ategory Type 2 Type 2 UL Nominal Discharge urrent (In), 20 ka 20 ka 15 Impulses 8/20 us Max. Discharge urrent (Imax), 50 ka 50 ka UL Voltage Protection Rating (VPR) 1.2 kv 1.6 kv Protection Level (Up) 1200 V 1600 V UL Short-ircuit urrent Rating (SR) 200 ka 200 ka Sparkover time / Drop-out time <100 ns <100 ns Overcurrent Protection No fuse required in discharge circuit No fuse required in discharge circuit onnection (network) Screw connections (2-14AWG) Screw connections (2-14AWG) Remote Signal Option (ontact Rating) 250 V / 0,5 A, 48 VD /0,1 A 250 V / 0,5 A, 48 VD /0,1 A Mounting DIN-rail, TS 35 DIN-rail, TS 35 Operating Temp Operating Altitude (Max.) 2,000m 2,000m Relative Humidity 0-95% non-condensing 0-95% non-condensing Enclosure Material Thermoplastic UL94-V0 Thermoplastic UL94-V0 Environmental Rating IP 20 IP 20 Weight (g) and (mm) SPD II 0 SPD II 1 SPD II 1 R UL 1449 (A and ANADA) 142 g; 18W x 100H x.5d 140 g; 18W x 90H x.5d 142 g; 18W x 100H x.5d Surge Protector Type Part No. Type Part No. Spare arrester 120V nom. SPD II 0 150V/40kA Spare arrester 230V nom. SPD II 0 280V/40kA SPD assembly w/o relay SPD II 1 150V/40kA SPD II 1 280V/40kA SPD assembly with relay SPD II 1 R 150V/40kA SPD II 1 R 280V/40kA Bus bars Type Part No. Type Part No. 2-pole jumper QB QB pole jumper QB QB pole jumper QB QB , 3- and 4-pole Jumpers

3 SPD II A Surge Protectors For transient voltage protection of single and multi-phase circuits, in the main electrical panel, downstream of the main circuit breaker, or in control panels. SPD II 0 400V/40KA SPD II 1 400V/40KA SPD II 1 R 400V/40KA SPD II 0 550V/40kA SPD II 1 550V/40kA SPD II 1 R 550V/40kA A Network 277/347 V, Single phase 480 V, Single phase onnection Mode 1 Pole, L-N or L-G. 1 Pole, L-N or L-G. Max. Operating Voltage (MOV) 385 VA 550 VA Leakage urrent at Uc <1mA <1mA Follow urrent None None UL ategory Type 2 Type 2 UL Nominal Discharge urrent (In), 20 ka 20 ka 15 Impulses 8/20 us Max. Discharge urrent (Imax), 50 ka 50 ka UL Voltage Protection Rating (VPR) 1.8 kv 2.5 kv Protection Level (Up) 1800 V 2500 V UL Short-ircuit urrent Rating (SR) 200 ka 200 ka Sparkover time / Drop-out time <100 ns <100 ns Overcurrent Protection No fuse required in discharge circuit No fuse required in discharge circuit onnection (network) Screw connections (2-14AWG) Screw connections (2-14AWG) Remote Signal (ontact Rating) 250 V / 0,5 A, 48 VD /0,1 A 250 V / 0,5 A, 48 VD /0,1 A Mounting DIN-rail, TS 35 DIN-rail, TS 35 Operating Temp Operating Altitude (Max.) 2,000m 2,000m Relative Humidity 0-95% non-condensing 0-95% non-condensing Enclosure Material Thermoplastic UL94-V0 Thermoplastic UL94-V0 Environmental Rating IP 20 IP 20 Weight (g) and (mm) SPD II 0 SPD II 1 SPD II 1 R UL 1449 (A and ANADA) 150 g; 18W x 100H x.5d 150 g; 18W x 100H x.5d Surge Protector Type Part No. Type Part No. Spare arrester 277V nom. SPD II 0 400V/40kA Spare arrester 440/480V nom. SPD II 0 550V/40kA SPD assembly w/o relay SPD II 1 400V/40kA SPD II 1 550V/40kA SPD assembly with relay SPD II 1 R 400V/40kA SPD II 1 R 550V/40kA Bus bars Type Part No. Type Part No. 2-pole jumper QB QB pole jumper QB QB pole jumper QB QB , 3- and 4-pole Jumpers 3

4 SPD II A Surge Protectors Basic A configurations 1 (with remote signaling options) L1 L2 L3 SPD parts needed: Nom. V Description Qty Qty Qty Part No. 110/120V SPD II 150V/40kA /240V SPD II 280V/40kA V SPD II 400V/40kA V SPD II 550V/40kA All QB All QB Basic A configurations 2 (with remote signaling options) L1 L2 L3 N SPD parts needed: Nom. V Description Qty Part No. 110/120V SPD II 1 R 150V/40kA /240V SPD II 1 R 280V/40kA V SPD II 1 R 400V/40kA V SPD II 1 R 550V/40kA All QB

5 SPD II D Surge Protectors For use on the D side of photovoltaic installations, typically in a combiner enclosure, protecting the D output and return conductor to the ground. SPD II 0 PV 600VD SPD II 2 PV 600VD SPD II 2 R PV 600VD SPD II 0 PV 1000VD SPD II 2 PV 1000VD SPD II 2 R PV 1000VD SPD II 0 PV 1200VD SPD II 3 PV 1200VD SPD II 3 R PV 1200VD D Network 600 VD 1000 VD 1200 VD onnection Mode Screw connection Screw connection Screw connection Max. Operating Voltage (MOV) 550 VD 1000 VD 1200 VD Leakage urrent at Uc <1mA <1mA <1mA UL ategory Type 2 Type 2 Type 2 UL Nominal Discharge urrent (In), 5 Impulses 8/20 us Max. Discharge urrent (Imax), 20 ka 20 ka 20 ka 50 ka 50 ka 50 ka UL Voltage Protection Rating (VPR) 2 kv 4 kv 4 kv Protection Level (Up) 2000 V 4000 V 4000 V UL Short-ircuit urrent Rating (SR) 200 ka 200 ka 200 ka Sparkover time / Drop-out time <100 ns <100 ns <100 ns Overcurrent Protection No fuse required in discharge circuit No fuse required in discharge circuit No fuse required in discharge circuit onnection (network) Screw connection, pluggable Screw connection, pluggable Screw connection, pluggable Remote Signal (ontact Rating) 250 V / 0,5 A, 48 VD /0,1 A 250 V / 0,5 A, 48 VD /0,1 A 250 V / 0,5 A, 48 VD /0,1 A Mounting DIN-rail, TS 35, TS 35 x 15, TS 35 x 7.5 DIN-rail, TS 35, TS 35 x 15, TS 35 x 7.5 DIN-rail, TS 35, TS 35 x 15, TS 35 x 7.5 Operating Temp Operating Altitude (Max.) 2000m 2000m 2000m Relative Humidity 0-95% non-condensing 0-95% non-condensing 0-95% non-condensing Enclosure Material Thermoplastic UL94-V0 Thermoplastic UL94-V0 Thermoplastic UL94-V0 Environmental Rating IP 20 IP 20 IP 20 Weight (g) (mm) 36W x 100H x.5d 36W x 100H x.5d 54W x 100H x.5d UL 1449 (A and ANADA) UL File E354261, Type 2 UL1449 Ed. 3, SA UL File E354261, Type 2 UL1449 Ed. 3, SA UL File E354261, Type 2 UL1449 Ed. 3, SA Surge Protector Type Part No. Type Part No. Type Part No. Spare arrester 600V nom. SPD II 0 PV 600VD Spare arrester 1000V nom. SPD II 0 PV 1000VD Spare arrester 1200V nom. SPD II 0 PV 1200VD PV SPD assembly w/o relay SPD II 2 PV 600VD SPD II 2 PV 1000VD SPD II 3 PV 1200VD PV SPD assembly with relay SPD II 2 R PV 600VD SPD II 2 R PV 1000VD SPD II 3 R PV 1200VD SPD II 2 PV SPD II 3 PV 5 PSPD II 2 R PV PSPD II 3 PV

6 SPD II Surge Protectors 6 Subject to technical changes 05/13 1M LIT1308

7 SPD II D Surge Protectors SPD II Surge Protectors For use on the D side of photovoltaic installations, typically in a combiner enclosure, protecting the D output and return conductor to the ground. SPD II 0 PV 600VD SPD II 2 PV 600VD SPD II 2 R PV 600VD SPD II 0 PV 1000VD SPD II 2 PV 1000VD SPD II 2 R PV 1000VD SPD II 0 PV 1200VD SPD II 3 PV 1200VD SPD II 3 R PV 1200VD Datasheet SPD II 1 Surge Protectors for A Power Distribution SPD II PV Surge Protectors for Photovoltaic Installations TRIM D Network 600 VD 1000 VD 1200 VD onnection Mode Screw connection Screw connection Screw connection Max. Operating Voltage (MOV) 550 VD 1000 VD 1200 VD Leakage urrent at Uc <1mA <1mA <1mA UL ategory Type 2 Type 2 Type 2 UL Nominal Discharge urrent (In), 20 ka 20 ka 20 ka 5 Impulses 8/20 us Max. Discharge urrent (Imax), 50 ka 50 ka 50 ka UL Voltage Protection Rating (VPR) 2 kv 4 kv 4 kv Protection Level (Up) 2000 V 4000 V 4000 V UL Short-ircuit urrent Rating (SR) 200 ka 200 ka 200 ka Sparkover time / Drop-out time <100 ns <100 ns <100 ns Overcurrent Protection No fuse required in discharge circuit No fuse required in discharge circuit No fuse required in discharge circuit onnection (network) Screw connection, pluggable Screw connection, pluggable Screw connection, pluggable Remote Signal (ontact Rating) 250 V / 0,5 A, 48 VD /0,1 A 250 V / 0,5 A, 48 VD /0,1 A 250 V / 0,5 A, 48 VD /0,1 A Mounting DIN-rail, TS 35, TS 35 x 15, TS 35 x 7.5 DIN-rail, TS 35, TS 35 x 15, TS 35 x 7.5 DIN-rail, TS 35, TS 35 x 15, TS 35 x 7.5 Operating Temp Operating Altitude (Max.) 2000m 2000m 2000m Relative Humidity 0-95% non-condensing 0-95% non-condensing 0-95% non-condensing Enclosure Material Thermoplastic UL94-V0 Thermoplastic UL94-V0 Thermoplastic UL94-V0 Environmental Rating IP 20 IP 20 IP 20 Weight (g) (mm) 36W x 100H x.5d 36W x 100H x.5d 54W x 100H x.5d UL 1449 (A and ANADA) UL File E354261, Type 2 UL1449 UL File E354261, Type 2 UL1449 UL File E354261, Type 2 UL1449 Ed. 3, SA Ed. 3, SA Ed. 3, SA Surge Protector Type Part No. Type Part No. Type Part No. Spare arrester 600V nom. SPD II 0 PV 600VD Spare arrester 1000V nom. SPD II 0 PV 1000VD Spare arrester 1200V nom. SPD II 0 PV 1200VD PV SPD assembly w/o relay SPD II 2 PV 600VD SPD II 2 PV 1000VD SPD II 3 PV 1200VD PV SPD assembly with relay SPD II 2 R PV 600VD SPD II 2 R PV 1000VD SPD II 3 R PV 1200VD Weidmuller s SPD II 1 series transient voltage surge protectors consist of a range of innovative, compact modules for the protection of low voltage A distribution systems or (PV models) for D photovoltaic installations. In A applications, the SPD II 1 would be installed downstream of the main circuit breaker and fuse(s), connected between each live conductor to be protected and ground. For multi-phase circuits, multiple modules are used with jumper options between ground terminals and permitting a single connection to ground. In photovoltaic applications, the SPD II 1 PV would typically be in a combiner enclosure protecting the D output and return conductor to ground. Voltage limiting technology is integrated, which differentiates between transient pulses and longer-lasting overvoltages. This circuitry eliminates the disadvantages of varistor devices (MOVs) which, in competitive products, may switch-on inadvertently in conditions where the supply voltage is not well-regulated. Weidmuller s hybrid arrester design ensures efficient MOV operation and hence conserves energy, maximizes the operating lifetime of the arrester and eliminates arcing when the thermal disconnect operates. Each module is a two-part construction, comprising a TS35 DINrail mountable base and a pluggable replaceable arrester, with each single-conductor assembly only 18mm wide. Products are specified by their working voltage level, or maximum continuous operating voltage (MOV) and each has a maximum surge current rating of 50kA. Base/arrester assemblies are available either with or without a remote signaling option and arresters are available as spare parts. Models for LV A distribution or photovoltaic installations Quick replacement with spare pluggable, replaceable arresters Nominal voltages up to 480VA (550V MOV) or 1200VD Maximum surge current (Imax) 50kA Remote status signaling option UL1449 Ed3 approved and SA equivalent No discharge path fuse needed (Type 2) SPD II 2 PV SPD II 3 PV Weidmuller, anada 10 Spy ourt Markham, Ontario L3R 5H6 Telephone: (800) Facsimile: (877) info1@weidmuller.ca Website: Weidmuller, Mexico Blvd. Hermanos Serdán 698, ol. San Rafael Oriente Puebla, Puebla, Mexico.P Telephone: Facsimile: clientes@weidmuller.com.mx Website: Weidmuller, United States 821 Southlake Blvd. Richmond, Virginia Telephone: (800) Facsimile: (804) info@weidmuller.com Website: 5 PSPD II 2 R PV PSPD II 3 PV 6 Subject to technical changes 05/13 1M LIT1308

8 SPD II A Surge Protectors SPD II A Surge Protectors SPD II A Surge Protectors For transient voltage protection of single and multi-phase circuits, in the main electrical panel, downstream of the main circuit breaker, or in control panels. SPD II 0 150V/40kA SPD II 1 150V/40kA SPD II 1 R 150V/40kA SPD II 0 280V/40KA SPD II 1 280V/40KA SPD II 1 R 280V/40KA For transient voltage protection of single and multi-phase circuits, in the main electrical panel, downstream of the main circuit breaker, or in control panels. SPD II 0 400V/40KA SPD II 1 400V/40KA SPD II 1 R 400V/40KA SPD II 0 550V/40kA SPD II 1 550V/40kA SPD II 1 R 550V/40kA Basic A configurations 1 (with remote signaling options) L1 L2 L3 A Network 120 V, Single phase 230 V, Single phase onnection Mode 1 Pole, L-N or L-G. 1 Pole, L-N or L-G. Max. Operating Voltage (MOV) 150 VA 277 VA Leakage urrent at Uc <1mA <1mA Follow urrent None None UL 1449 ategory Type 2 Type 2 UL Nominal Discharge urrent (In), 20 ka 20 ka 15 Impulses 8/20 us Max. Discharge urrent (Imax), 50 ka 50 ka UL Voltage Protection Rating (VPR) 1.2 kv 1.6 kv Protection Level (Up) 1200 V 1600 V UL Short-ircuit urrent Rating (SR) 200 ka 200 ka Sparkover time / Drop-out time <100 ns <100 ns Overcurrent Protection No fuse required in discharge circuit No fuse required in discharge circuit onnection (network) Screw connections (2-14AWG) Screw connections (2-14AWG) Remote Signal Option (ontact Rating) 250 V / 0,5 A, 48 VD /0,1 A 250 V / 0,5 A, 48 VD /0,1 A Mounting DIN-rail, TS 35 DIN-rail, TS 35 Operating Temp Operating Altitude (Max.) 2,000m 2,000m Relative Humidity 0-95% non-condensing 0-95% non-condensing Enclosure Material Thermoplastic UL94-V0 Thermoplastic UL94-V0 Environmental Rating IP 20 IP 20 Weight (g) and (mm) SPD II 0 SPD II 1 SPD II 1 R UL 1449 (A and ANADA) 142 g; 18W x 100H x.5d 140 g; 18W x 90H x.5d 142 g; 18W x 100H x.5d Surge Protector Type Part No. Type Part No. Spare arrester 120V nom. SPD II 0 150V/40kA Spare arrester 230V nom. SPD II 0 280V/40kA SPD assembly w/o relay SPD II 1 150V/40kA SPD II 1 280V/40kA SPD assembly with relay SPD II 1 R 150V/40kA SPD II 1 R 280V/40kA Bus bars Type Part No. Type Part No. 2-pole jumper QB QB pole jumper QB QB pole jumper QB QB A Network 277/347 V, Single phase 480 V, Single phase onnection Mode 1 Pole, L-N or L-G. 1 Pole, L-N or L-G. Max. Operating Voltage (MOV) 385 VA 550 VA Leakage urrent at Uc <1mA <1mA Follow urrent None None UL ategory Type 2 Type 2 UL Nominal Discharge urrent (In), 20 ka 20 ka 15 Impulses 8/20 us Max. Discharge urrent (Imax), 50 ka 50 ka UL Voltage Protection Rating (VPR) 1.8 kv 2.5 kv Protection Level (Up) 1800 V 2500 V UL Short-ircuit urrent Rating (SR) 200 ka 200 ka Sparkover time / Drop-out time <100 ns <100 ns Overcurrent Protection No fuse required in discharge circuit No fuse required in discharge circuit onnection (network) Screw connections (2-14AWG) Screw connections (2-14AWG) Remote Signal (ontact Rating) 250 V / 0,5 A, 48 VD /0,1 A 250 V / 0,5 A, 48 VD /0,1 A Mounting DIN-rail, TS 35 DIN-rail, TS 35 Operating Temp Operating Altitude (Max.) 2,000m 2,000m Relative Humidity 0-95% non-condensing 0-95% non-condensing Enclosure Material Thermoplastic UL94-V0 Thermoplastic UL94-V0 Environmental Rating IP 20 IP 20 Weight (g) and (mm) SPD II 0 SPD II 1 SPD II 1 R UL 1449 (A and ANADA) 150 g; 18W x 100H x.5d 150 g; 18W x 100H x.5d Surge Protector Type Part No. Type Part No. Spare arrester 277V nom. SPD II 0 400V/40kA Spare arrester 440/480V nom. SPD II 0 550V/40kA SPD assembly w/o relay SPD II 1 400V/40kA SPD II 1 550V/40kA SPD assembly with relay SPD II 1 R 400V/40kA SPD II 1 R 550V/40kA Bus bars Type Part No. Type Part No. 2-pole jumper QB QB pole jumper QB QB pole jumper QB QB SPD parts needed: Nom. V Description Qty Qty Qty Part No. 110/120V SPD II 150V/40kA /240V SPD II 280V/40kA V SPD II 400V/40kA V SPD II 550V/40kA All QB All QB Basic A configurations 2 (with remote signaling options) L1 L2 L3 N SPD parts needed: Nom. V Description Qty Part No. 110/120V SPD II 1 R 150V/40kA /240V SPD II 1 R 280V/40kA V SPD II 1 R 400V/40kA V SPD II 1 R 550V/40kA All QB , 3- and 4-pole Jumpers 2-, 3- and 4-pole Jumpers 3 4