Model 332 Differential Pressure Transmitter
|
|
- Beverly Jackson
- 6 years ago
- Views:
Transcription
1 Model Differential Pressure Transmitter USERS GUIDE Please read carefully before using. Manufactured by: FURNESS CONTROLS LIMITED Beeching Road, Bexhill, East Sussex, TN9 LJ, England. Telephone (044) 706 Fax: (044) Web Site:
2 TABLE OF CONTENTS TABLE OF CONTENTS... REVISION RECORD... SAFETY NOTES AND RECOMMENDATIONS...4 INTRODUCTION...5 GENERAL DESCRIPTION...5 ENCLOSURE...5 INSTALLATION...6 MOUNTING...6 PNEUMATIC...6 ELECTRICAL...7 COMMISSIONING... CALIBRATION... SPECIFICATION... DIMENSION DRAWINGS...4 BASIC INSTRUMENT...4 PIPE MOUNTING KIT...4 FLUSH MOUNTING KIT...5 PANEL MOUNTING KIT...5 Model Users Guide Issue 8 Page
3 REVISION RECORD Issue Date Summary of changes 5/0/00 Addition of 0.4 to V -wire range 8/0/0 Relay wiring connections added /0/0 Typical wiring configurations and relay ratings added and model range amended a 08/0/0 Clarification added regarding relay states and keypad use. b 8//0 Relay and delay options added to manual. 4 8/04/0 Moved menu description to 00 Series Supplement 5 /0/06 Added info on 0.5 V output options and Auto Zero hardware option. Changed calibration service from NAMAS to UKAS. 6 9/07/06 Added wiring drawings for all o/p options & auto/remote zero 7 7/05/09 Remote Zero switch timing 8 4/0/0 Dimension drawings added. Specification updated. Calibration interval added. Page Model Users Guide Issue 8
4 SAFETY NOTES AND RECOMMENDATIONS PLEASE READ CAREFULLY. Read these instructions and this users guide carefully.. All electrical supplies to the equipment must be externally fused with an appropriately rated fuse for safety.. Always unplug the equipment from the supply before carrying out any servicing. 4. The air supply must be turned off before carrying out any work on the pneumatic system. The air supply must not exceed that specified on the instrument or in the Test Certificate. 5. If in doubt about any aspect of safety with the equipment then contact Furness Controls BEFORE proceeding. Model Users Guide Issue 8 Page 4
5 INTRODUCTION This guide should be read in conjunction with the 00 Series Supplement General Description The FCO is a fully configurable, industrial differential pressure transmitter. The pressure cell is based on the unique Furness Controls capacitive sensor of proven reliability. A microprocessor is used to control all functions of stability, such as temperature correction and linearity. The output can be scaled as a linear or square root function to facilitate the use of Pitot Static Tubes or other primary flow elements. The FCO is suitable for industrial applications of control, measurement and monitoring. Features include: Optional large character liquid crystal 4½ digit display Linear or square root output 0: range adjustment using Model 0 interface Optional Configurations: -Wire 4 to 0mA Current output -Wire Voltage output 0 to 0.5V, 0 to V, 0 to V, 0 to 5V, 0 to 0V, 0. to 0.5V, 0. to V, 0.4 to V, to 5V, to 0V 4-Wire Voltage output 0 to 0.5V, 0 to V, 0 to V, 0 to 5V, 0 to 0V, ±0.5V, ±V, ±V, ±5V, ±0V 4-Wire Isolated 4 to 0mA Current output 4-Wire Isolated Voltage output 0 to V, 0 to V, 0 to 5V, 0 to 0V, ±0.5V, ±V, ±V, ±5V, ±0V Remote Zeroing Function Zero the FCO with an externally fitted button, or suitable electronic circuitry. Available to instruments with the necessary hardware option fitted. Auto Zeroing Function Adjustable delay between 0 and 4.0 Hours with 0. hour resolution. Available to instruments with the necessary hardware option fitted. Typical applications include: Combustion pressure measurement and control of industrial furnaces Air pressure measurement and control of dryers, kilns and ovens Air flow measurement in conjunction with pitot static tubes, orifice plates or venturi Enclosure The instrument is housed in an IP54 rated ABS enclosure. Pneumatic connections (fitted as standard) are for 4mm i/d push on tubing. Optional pneumatic connections are: /8 BSPP(f) threaded adaptor, and /4"BSPP(f) threaded adaptor Page 5 Model Users Guide Issue 8
6 INSTALLATION Mounting The recommended mounting position of the FCO is with the pressure entry ports facing directly downwards. This helps prevent the ingress of dust and liquid. Due to the sensitivity of lower range instruments, they should not be mounted in areas where they will be subjected to high vibration as this could cause spurious readings. The enclosure has four mounting holes for M4 screws, which are accessible with the cover removed. Pneumatic All pipework should slope downwards from the instrument to make it self draining. When using the instrument to measure pressure at a single point with long pipe runs the reference port should be piped in parallel, with the pipe left open at the process end. Model Users Guide Issue 8 Page 6
7 Electrical Connectors Cable entry is via a right-angled Type C DIN connector with M6 cable gland mounted on the bottom of the instrument. Where optional features are added to the standard FCO (i.e. relay o/p, auto zero, or remote zero) the same right-angled Type C DIN connector is used to provide power and/or to gain access to the various functions provided by that option. A two to four core cable, up to 6.0mmO.D., can be used with the standard socket. The terminals provided with the socket are of the screw type. The socket must first be dismantled, by removing the securing screw and pushing the centre terminal block from the housing. The cable is passed though the gland and housing. Conductors are terminated as detailed below. Each conductor should be stripped free of insulation for a length of -5mm. Securing Screw Aux Relay Relay Remote Zero Circuitry Auto Zero Circuitry Relay Circuitry Housing Transmitter Circuitry Terminal Block FCO System Diagram Page 7 Model Users Guide Issue 8
8 Transmitter Connection Refer to the instruments rating label for power supply requirements and configuration. 4 to 0mA Isolated 4 to Isolated Voltage Output PIN Output 0mA O/P Voltage Output -Wire -Wire 4-Wire 4-Wire 4-Wire -ve n.c. -ve -out -Vout +ve +ve +ve +4Vdc +4Vdc n.c. O/P O/P +out +Vout n.c. 0Vdc 0Vdc 0Vdc 0Vdc Note: the user cannot reassign pin assignments. The diagrams below show typical wiring configurations: wire - 4 to 0mA Output wire - Voltage Output 4 wire - Voltage Output No Connection Vout Vout +Ve -Ve +Ve No Connection Voltage Indicator +Ve -Ve Voltage Indicator ma Indicator No Connection 0V 0V +V 0V Supply 9Vdc to 6Vdc +/-0% +V 0V Supply 4Vdc to 6Vdc +/-0% ma No Load +V 0V -V Supply +/-4Vdc to +/-8Vdc +/-0% ma No Load 4 wire - Isolated 4 to 0mA Output 4 wire - Isolated Voltage Output +maout(iso) ma Indicator +Vout(iso) Voltage Indicator 4V Isolation Barrier -maout(iso) 4V Isolation Barrier -Vout(iso) 0V 0V 4V 0V Supply 4Vdc +/-0% 4mA No Load 4V 0V Supply 4Vdc +/-0% 4mA No Load Model Users Guide Issue 8 Page 8
9 Auxiliary Connection The connector fitted to the top left of the case has terminals for powering the internal circuitry for the relay outputs & auto zero functions, and must be connected to an external 4Vdc power source. The same connector is also used to connect to an external (remote) switch or suitable electronic circuitry for zeroing the transmitter. PIN Remote Auto Relay Zero Zero Outputs RZ(0V) RZ(0V) RZ(0V) RZ(+V) RZ(+V) RZ(+V) 4Vdc 4Vdc 0Vdc 0Vdc Supply Specification Remote Zero power supply 5Vdc to 4Vdc +/-0%, 5mA (min) Switch contact time 0.sec (min) to.0sec (max) Auto Zero power supply 4Vdc +/-0%, 0mA (min) Relay power supply 4Vdc +/-0%, 50mA (min) Note: When the Zero is triggered, the display and output are frozen for.5 seconds while the pneumatic ports are isolated from the process ports. The diagram below shows a typical wiring configuration: NOTE: Remote Zero is an optional feature 4Vdc 4Vdc Supply Remote Zero RZ(+V) RZ(0V) 0V 0V Page 9 Model Users Guide Issue 8
10 Relay Connections (Option) The FCO can optionally incorporate a pair of relays for triggering auxiliary equipment such as alarms. Two connectors for the relays are located on the top right of the case. The middle connector is for the relay contacts. The right-hand connector is for the relay contacts. The relays do not feature any contact suppression. Relay Relay Relay Connectors PIN Relay NO NO NC NC Relay unused unused COM COM Relay states are shown for the instrument switched off. Relay contact ratings 55Vac/0Vdc (non inductive load) NOTE: refer to the 00 Series Supplement for setting the relay trigger levels. The diagram below shows a typical wiring configuration: No Connection No Connection nc no nc no com Relay com Relay Model Users Guide Issue 8 Page 0
11 COMMISSIONING Make the electrical and pneumatic connections as recommended. Turn on the power supply. Configuration settings (such as range, display settings, etc.) may be changed using the FCO0 utility cable, refer to the 00 series supplement for further details. Check that either the auxiliary current sensing or voltage-measuring device that is being used is registering. If not, check the supply voltage is within specified limits and inspect for poor connections. After fixing the instrument in position, allow at least one hour before commencing the final commissioning. After commissioning, allow the instrument to reach ambient temperature for at least 0 minutes. With no pressure applied, check the output is correct for zero input. If not:- press the zero button (indicated below) activate the remote zero (if fitted) or enable the auto zero function (if fitted), the delay time may have to be temporarily set to 0.hour (refer to the 00 series supplement for further details). Zero Button NOTE: if the auto zero valve is fitted, pressing either the zero button or the remote zero will force an auto zero cycle. In the unlikely event an error message is displayed, refer to the 00 series supplement for further details. The instrument is now ready for operation. Page Model Users Guide Issue 8
12 CALIBRATION Furness Controls recommend that all pressure transmitters and flow devices are recalibrated annually. For critical applications, it is advisable to check the calibration more frequently. All calibration of the FCO is performed through a PC using the FCO0 interface unit and software. Refer to the 00 Series Supplement for further information regarding the recalibration of the FCO. Contact our Furness Controls UKAS accredited calibration laboratories for further information. Model Users Guide Issue 8 Page
13 SPECIFICATION Features Models/Ranges Output Options Display (Optional) Adjustable Damping Square Root function Trip Level Relays Zero Control Pneumatic Ports Model: ±50Pa Model: ±50Pa Model: ±500Pa Model4: ±500Pa Model5: ±0kPa Model6: ±0kPa High pressure ranges available on request wire 4 0mA wire voltage: 0 VDC to 0 0VDC full scale 4 wire voltage: 0 VDC to 0 0VDC full scale 4 wire voltage: ± VDC to ±0 VDC full scale 4 wire isolated: any of the ma or voltages above Most common differential pressure, volumetric flow, mass flow, and velocity units 0.0 to 60.0 seconds Optional Optional: relays, rated 55Vac, 0Vdc Optional: Automatic or Remote Barbs with locknuts for 6mm OD x 4mm ID for flexible tubing ⅛ BSPF ¼ BSPF Performance Enhanced 0 C Standard 0 C Span Adjustment Long Term Drift Temperature Coefficients 0% to 00% range: < ± (0.5% reading + digit) Note: Unipolar span only, standard 0 to 0% range: < ± (0.05% range + digit) accuracy applies to bipolar span. 0% to 00% range: < ± (0.5% reading + digit) 0 to 0% range: < ± (0.05% range + digit) 0% to 00% of range Note: Span can be set anywhere within instruments range. For span < 0% of range, accuracy is reduced to the standard specification Typically 0.% per annum Standard Zero: < 0.%/ C Range: < 0.4%/ C Working Temperature 0 to 60 C Minimum Step Response 00ms Output Update 50ms Output Resolution Better than 0.0 % Span Overload 0 x DP range Static Pressure ± bar Gauge Enhanced Zero: < 0.0%/ C Range: < 0.0%/ C Construction Enclosure Dimensions Materials in Contact With Media Media Compatibility Weight IP54 rated ABS Choice of mounting options 0 x 80 x 58mm Copper, brass, nickel, mica & PVC Air and non corrosive gases max 95% humidity non condensing 0.5kg Page Model Users Guide Issue 8
14 Basic Instrument DIMENSION DRAWINGS Pipe Mounting Kit Model Users Guide Issue 8 Page 4
15 Flush Mounting Kit Panel Mounting Kit Page 5 Model Users Guide Issue 8
PS-AULDP Series. Overview. Applications. Features & Benefits. Datasheet. Ultra Low Air Differential Pressure Transmitters
PS-AULDP Series Datasheet Ultra Low Air Differential Pressure Transmitters Overview The PS-AULDP Series are ultra-low-pressure transmitters. These devices can be used to measure differential pressure between
More informationDP DP2500 DP0250
DP7000 - DP2500 DP0250 PB_DP7000_DP2500 - DP0250_07 2016 Field adjustable, multi-range differential pressure transmitters Product Bulletin The Delta Pressure transmitter series of Johnson Controls, with
More informationDP2500 DP0250. Differential Pressure Transmitter. Product Bulletin
DP2500 DP0250 Differential Pressure Transmitter Product Bulletin The DP Low Differential Pressure Transmitter series is an accurate and cost competitive solution for measuring low pressures of air and
More informationTPE 1464 Series Pressure Transducer
TPE 1464 Series Pressure Transducer Description The KMC TPE 1464 series of pressure transducers incorporate a gauge pressure transmitter featuring low hysteresis, excellent repeatability, and longterm
More informationCDD4 Duct Carbon Dioxide Transmitter
Drill or punch a 1-1/8 or 1-1/4 hole in the duct at the preferred location and insert the probe into the hole to mark the enclosure mounting holes. Remove the unit and drill the four mounting holes. Clean
More informationTOXALERT MODEL AIR 2000
TOXALERT MODEL AIR 2000 NOTE: Toxalert s Model GVU-CO 2 Sensor is the same as the Air2000R. Microprocessor-based, Infrared Environmental CO 2 Sensor OPERATOR S MANUAL TOXALERT TM INTERNATIONAL INC. P.O.
More informationCDD Carbon Dioxide Transmitter
Introduction The OSA CO2 transmitter uses Infrared Technology to monitor CO2 levels within a range of 0 2000 ppm and outputs a linear 4-20 ma or 0-5/0-10 Vdc signal. The enclosure is designed to operate
More informationMST2000 Loop Powered Multivariable SMARTFLOW Transmitter
MST2000 Loop Powered Multivariable SMARTFLOW Transmitter MST2000 Loop Powered Multivariable SMARTFLOW Transmitter Brandt Instruments MST2000 Series Loop Powered Multivariable SMARTFLOW Transmitter sets
More informationP30-2. Overview. Pressure Transmitter Datasheet. *High Quality* 3 Years Warranty. At a Glance. Function. Application
P30-2 Pressure Transmitter Datasheet At a Glance *High Quality* 3 Years Warranty Premium Pressure Transmitter for gauge and pressure measurement with 3 years warranty High repeatability and long-term stability
More informationRelative, and differential pressure transmitter type 699
Relative, and differential pressure transmitter type 699 Pressure range -1... 1 mbar / 0... 0.3 50 mbar The type 699 transmitters are available in switchable pressure ranges and with or without display.
More informationIndicating Digital Transmitter for Differential Pressure and Flow. Media 6 with LCD Media 6 with LED
Indicating Digital Transmitter for Differential Pressure and Flow Media 6 with LCD Media 6 with LED Application Microprocessor-controlled transmitter for measuring and indicating the differential pressure
More informationPressure range mbar / mbar
Pressure range -1... 1 mbar / 0... 0.3 50 mbar Technical overview Pressure range Relative and differential Operating conditions Medium Temperature Tolerable overload on one side Rupture pressure Application
More information14 Pressure Measurement. Measuring Devices Description Pressure range Connection Device Page
Measuring Devices Pressure range Connection Device Page Digital display mounting, für niedrige Drücke 0 2. mbar / 2. bar 4 mm tube MPV, MPA.02 portable, hand-operated 0 1 mbar / 10 bar 4 mm tube MHA.03
More informationMiniaturised pressure sensor Model M-10, standard version Model M-11, version with flush diaphragm
Electronic pressure measurement Miniaturised pressure sensor Model M-10, standard version Model M-11, version with flush diaphragm WIKA data sheet PE 81.25 for further approvals see page 5 MicroTronic
More informationDWYER INSTRUMENTS, INC. Series AVUL Air Velocity Transmitter. Specifications - Installation and Operating Instructions.
Series AVUL Air Velocity Transmitter Specifications - Installation and Operating Instructions Bulletin P-AVUL 3-49/64 [95.71] 2-43/64 [67.92] 1/2 NPS 3-3/16 [80.81] 1-19/32 [40.59] 31/32 24.58 3-33/64
More informationMagnetically Actuated Safety Interlock Switches
Conforms to EN10, EN292, EN020-1 CSA and BG approved Actual Size Magnetically Actuated Safety Interlock Switches Large selection choose from a large selection of contact configurations housed in plastic,
More informationHigh-Precision Pneumatic Pressure Controller Series CPC8000-L/-X
R Calibration Technology High-Precision Pneumatic Pressure Controller Series CPC8000-L/-X WIKA Data Sheet CT 28.01 Applications Industry (laboratory, workshop and production) Pressure transmitter manufacture
More informationThe PM1000 series is a universal 4 digit LED plug-on display for transmitters with 4-20mA 2 wire output and fitted with DIN43650 connector.
PM1000 SERIES PLUG-ON DISPLAY BRIGHT LED DISPLAY INDICATION RANGE -999 TO +9999 FITS TO DIN 43650 CONNECTOR PLUG-ON TO ANY TRANSMITTER WITH 4-20MA OUTPUT EASY TO SCALE ON SITE ROBUST DESIGN SET POINT OPTION
More informationMicroTrans EQ Signal Processor. Operation & Maintenance Manual
MicroTrans EQ Signal Processor Operation & Maintenance Manual Engineered for accuracy, applicability, durability and simplicity in HVAC air systems and industrial process control loops TABLE OF CONTENTS
More informationHPS-M -2 DIFFERENTIAL PRESSURE TRANSMITTER. Mounting and operating instructions
DIFFERENTIAL PRESSURE Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 5 OPERATIONAL
More informationtechnical datasheet technical datasheet MTL660 Displays Loop-powered indicators for hazardous areas
technical datasheet technical datasheet MTL0 Displays Loop-powered indicators for hazardous areas Loop powered -0mA Field and panel mounting Environmental protection to IP7 Easy to configure Number of
More information350 SMART MANOMETER OPERATING INSTRUCTIONS
99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com 350 SMART MANOMETER OPERATING INSTRUCTIONS Meriam Instrument s 350 Smart Manometer
More informationOperating Instructions Differential Pressure Transducer PS27
Operating Instructions Differential Pressure Transducer PS27 halstrup-walcher GmbH Stegener Straße 10 79199 Kirchzarten/Germany Phone: +49 (0) 76 61/39 63 0 Fax: +49 (0) 76 61/39 63 99 E-mail: info@halstrup-walcher.com
More informationInCos-P Pressure sensor 20 Pa Pa
InCos-P Pressure sensor 20 Pa... 7.500 Pa Electrical pressure / differential pressure sensors 24 VAC/DC supply voltage, 0...10 V / (0) analogue Compact. Easy installation. Universal. Cost effective. Safe.
More informationMulti-range pressure and differential pressure transmitter
Page 1/6 Multi-range pressure and differential pressure transmitter Type 402005 Applications Ventilation Air conditioning Clean-room technology Flue draft mechanisms Filter monitoring Brief description
More informationTable of Contents. General Information. Document Sure-Aire Flow Monitoring System. User and Service Manual WARNING CAUTION
Document 476092 User and Service Manual Installation, Operation and Maintenance Manual Please read and save these instructions for future reference. Read carefully before attempting to assemble, install,
More informationOZONE SWITCH Model OS-6. OS-6 Features
USER MANUAL OZONE SWITCH Model OS-6 OS-6 Features The OS-6 is an industrial grade ozone controller and monitor. The OS-6 design is optimized for accuracy and ease of installation, setup and operation.
More informationMODEL: M5DY SEN TRONIC AG CURRENT LOOP SUPPLY. [2] POWER INPUT AC Power M: V AC (Operational voltage range V, Hz)
Super-mini Terminal Block Signal Conditioners M5-UNIT CURRENT LOOP SUPPLY Functions & Features Powering a 0 ma DC current loop Applicable to smart transmitters Isolation between the input and output Fast
More informationJUMO PINOS L01. Calorimetric flow sensor. Brief description. Special features. Customer benefits. Data Sheet
sales@jumo.co.uk info.us@jumo.net Page 1/9 JUMO PINOS L01 Calorimetric flow sensor Brief description The JUMO PINOS L01 flow sensor serves the measuring and monitoring of flow velocities of water and aqueous
More informationEE771 Series. Flowmeter for compressed air and gases in Industrial Applications. EE771 Compact. EE771 remote probe
Series Flowmeter for compressed air and gases in Industrial Applications The flowmeter of the series, based on the measurement principle of thermal mass flow, is ideally suited for the measurement of flow
More informationInsertion Flowmeter for compressed air and gases DN50 - DN700 (2-28 )
The flow meter is based on the thermal mass flow measurement and is ideal for measuring the flow of compressed air and gases in pipes from DN50 (2 ) to DN700 (28 ). With the, the consumption of compressed
More informationaccurate measurement of compressed air consumption and leakage detection Calibration certificates and continous calibration, OEKD calibration service
Series Flowmeter for compressed air and gases in Industrial Applications The flowmeter of the series, based on the measurement principle of thermal mass flow, is ideally suited for the measurement of flow
More informationF-SENSOR LOW AIR VELOCITY SENSOR
home FSENSOR LOW AIR VELOCITY SENSOR Ultra low air velocity measurement Output as linear Velocity or Air volume Excellent repeatability Excellent Zero Stability Climate chamber compensated Long term span
More informationLC2300 Level Controller Installation and Maintenance Instructions
4025350/5 IM-P402-72 AB Issue 5 LC2300 Level Controller Installation and Maintenance Instructions 1 General safety information LC2300 2 General product information 3 Installation >50% >100%
More informationIntrinsically Safe Barriers
Intrinsically Safe Barriers Description Page No. Safety Barriers 464-472 Din Rail Isolated Barriers 473-488 477 Intrinsically Safe Barriers Product Overview We have simplified intrinsic safety! Cooper
More informationPressure gauge for supervising cleanrooms series DMG5 Usermanual
Of wall mounting (AP) In wall mounting (UP) Content: 1. Safety advice 2. Device description 3. Requirements to connection with cables 4. The operation condition pressure measure 5. Configuration of the
More informationPneumatic Control/Feedback
897 /Feedback Type 897 can be combined with... Compact design Integrated pilot valve with manual override Internal control air routing Bright LED position indicator Automatic end position adjustment Type
More informationPneumatic Control/Feedback
897 /Feedback Type 897 can be combined with... Compact design Integrated pilot valve with manual override Internal control air routing Automatic end position adjustment With ATEX II cat. G/D and cat. D/G
More informationPowers TM Controls RL 243 MP Multi-Purpose Relay
Powers TM Controls Technical Instructions Document No. 155-042P25 RL 243-6 Description The Powers is a pneumatic auxiliary device designed to provide a variety of pneumatic control functions for the typical
More informationPressure sensors SPAN
Features At a glance Communication interface Convenient design Compact design 30x30 mm Degree of protection IP40 Reduced weight with QS4 Universal pressure measurement Pressure and vacuum 13 pressure measuring
More informationCDD4 Series Room CO2 Transmitter Installation Instructions
CDD4 Series Room CO2 Transmitter Installation Instructions Introduction The CO2 transmitter uses Infrared Technology to monitor CO2 levels and outputs a linear 4-20 ma or 0-5/0-10 Vdc signal. Options include
More informationFerrous metal (The sensing distance decreases with non-ferrous metal.) Power supply voltage (operating voltage range)
Description The sensors provide excellent results even with difficult-to-detect objects, e.g. small or thin parts, wires or bright metals. A variety of types cover a wide range of individual requirements
More informationPneumatic Control Unit for the integrated mounting on process valves
Pneumatic Control Unit for the integrated mounting on process valves Type 890 can be combined with Compact design Pilot valve with high air flow rate Internal control air channel Optical position indicator
More informationDigital electropneumatic Positioner for the integrated mounting on process control valves
Digital electropneumatic Positioner for the integd mounting on process control valves Type 8692 can be combined with Compact stainless steel design Graphic display with backlight Easy start-up by automatic
More informationInstruction Manual P82R Differential Pressure Transducer with Root- Extracted Characteristic Curve
Instruction Manual P82R Differential Pressure Transducer with Root- Extracted Characteristic Curve halstrup-walcher GmbH Stegener Straße 10 D-79199 Kirchzarten Germany Phone: +49 (0) 76 61/39 63 0 Fax:
More informationDifferential Liquid/Gas Pressure Transmitter
Installation Instruction Differential Liquid/Gas Pressure Transmitter Catalog Number(s) 1414-CPZ10FWFAA, 1414-IPZ10FWFAA Explosion Hazard WARNING Do not use in an explosive or hazardous environment, with
More informationIN-LINE. vpinstruments.com
VPFLOWSCOPE IN-LINE vpinstruments.com VPFlowScope In-line The VPFlowScope In-line measures flow, pressure and temperature simultaneously. It is the perfect solution for compressed air and technical gas
More informationMass Flow Meters & Controllers
Mass Flow Meters & Controllers HFM-D-3A/B HFC-D-3A/B 3A/B Mass Flow Meter 3A/B Mass Flow Controller HFM-D-305A/B HFC-D-307A/B 305A/B Mass Flow Meter 307A/B Mass Flow Controller FEATURES 3/3 Range 0-25
More informationDigital electropneumatic Positioner for the integrated mounting on process control valves
Digital electropneumatic Positioner for the integrated mounting on process control valves Type 8692 can be combined with Compact stainless steel design Graphic display with backlight Easy start-up Comprehensive
More informationWall-/Pipe Mounted Universal Process Indicator
Data Sheet SS/_8 Wall-/Pipe Mounted Universal Process Indicator High visibility LED display the clearest view of your process status 0.1% measurement accuracy precise indication of process measurement
More informationMSR Level Control Relay Module Operating Instructions for Level Control Relay Module Model: MSR
Operating Instructions for Level Control Relay Module Model: MSR MSR Operation Instructions Rev. Apr 07 Page 1/8 1. Note Please read and take note of these operating instructions before unpacking and commissioning.
More informationThread length (overall length) material
Cylindrical Proximity Sensor for Mobile Usage Designed and tested to keep your machines moving IP69k tested and certified for highest water resistance e1 type approval (according to automotive directive
More informationCarbon Monoxide (CO) Gas Detection and Control System
Carbon Monoxide (CO) Gas Detection and Control System DESCRIPTION Gas monitor with built-in carbon monoxide (CO) sensor, wall-mounted, accepts inputs from remote devices such as other gas sensors, temperature
More informationSLIMCON-6 24V DC POWERED ISOLATING SIGNAL CONVERTER
SLIMCON-6 24V DC POWERED ISOLATING SIGNAL CONVERTER Whilst every effort has been taken to ensure the accuracy of this document, we accept no responsibility for damage, injury, loss or expense resulting
More informationThread length. 27 (40) mm. 27 (44) mm. 27 (40) mm. 34 (50) mm. 34 (49) mm. 39 (60) mm. 39 (54) mm. 44 (65) mm. 44 (59) mm
Long Distance Cylindrical. Extra long for increased protection and sensing performance triple proximity sensors for flush mounting requirements. designed and tested for extra long life. Ordering Information
More informationJT400 Multivariable Transmitter
Product Specification Sheet JT400 Multivariable Transmitter Wireless Ultra Low Power Platform with Integrated, Chart Replacement Data Logging and I/O The industry s first, ultra-low power, multivariable
More informationPneumatic High-Speed Pressure Controller Model CPC3000
Calibration Technology Pneumatic High-Speed Pressure Controller Model CPC3000 WIKA Data Sheet CT 27.55 Applications Industry (laboratory, workshop and production) Pressure transmitter manufacture Calibration
More informationInBin-P Pressure switches from 5 Pa Pa
InBin-P Pressure switches from 5 Pa...100 Pa Electrical, binary pressure or differential pressure switches with adjustable switch activation delay 24 VAC/DC supply voltage, potential free switching contact
More informationDPC DPC PRECISION DIGITAL MASS FLOW CONTROLLER WITH MULTI-GAS FUNCTIONALITY
43 Design Features Simultaneously displays Mass Flow, Volumetric Flow, Pressure and Temperature. Multi-Gas functionality: support for 90 different gases and gas mixes. User Defined Mixture functionality
More informationINSTALLATION MANUAL. LC 200 Electronic Overload Guard. Software versione PW0501 R 0.3
INSTALLATION MANUAL LC 200 Electronic Overload Guard Software versione PW0501 R 0.3 CONTENTS MAIN FEATURES LC 200 TECHNICAL FEATURES Page 2 SYMBOLS Page 3 WARNINGS Page 3 IDENTIFICATION DATA PLATE Page
More informationTemperature and humidity regulator H3020 H3021 H3023 H3027. Instruction Manual
Temperature and humidity regulator H3020 H3021 H3023 H3027 Instruction Manual Table of content 1. GENERAL SAFETY RULES... 3 2. GENERAL DESCRIPTION... 4 3. REGULATOR MOUNTING AND CONNECTION... 4 4. DESCRIPTION
More informationFLOW MONITOR & TRANSMITTER
FLS M9.02 FLOW MONITOR & TRANSMITTER SAFETY INSTRUCTIONS General Statements Do not install and service the product without following the Instruction Manual. This item is designed to be connected to other
More informationDatasheet DE DB_EN_DE45_LCD Rev. ST4-G 11/17. Digital differential pressure switch / transmitter with colour-change LCD * *
09005351 DB_EN_DE45_LCD Rev. ST4-G 11/17 *09005351* Datasheet DE45 Digital differential pressure switch / transmitter with colour-change LCD 1 Product and functional description FISCHER Mess- und Regeltechnik
More informationINSTRUCTIONS FOR MODEL 1000 DIGITAL PROCESS INDICATOR AND ALARM
INSTRUCTIONS FOR MODEL 1000 DIGITAL PROCESS INDICATOR AND ALARM LOVE CONTROLS DIVISION Dwyer Instruments, Incorporated PO Box 338 Michigan City, IN 46361-0338 (800) 828-4588 (219) 879-8000 FAX (219) 872-9057
More informationSTT 3000 Series STT250 Smart Temperature Transmitters Specifications Models STT25H, STT25S, STT25M, STT25D EN0I-6031 March 2010
STT 3000 Series STT250 Smart Temperature Transmitters Specifications Models STT25H, STT25S, STT25M, STT25D EN0I-6031 March 2010 Introduction Honeywell s STT 3000 family of microprocessor based smart temperature
More informationInstallation and Maintenance Instructions for GC55 Differential Pressure Transducer Version 1.0 5/11
Installation and Maintenance Instructions for GC55 Differential Pressure Transducer Version 1.0 5/11 2011 Ashcroft Inc. 250 East Main Street, Stratford, CT 06614 USA Tel: 203-378-8281, Fax: 203-385-0402
More informationAnalyzer/Controller. ph/orp HART. Model 54e ph/orp ESSENTIAL INSTRUCTIONS WARNINGS RISK OF ELECTRICAL SHOCK
Instruction Sheet PN 51A-54epH/rev J October 2010 ph/orp HART Model 54e ph/orp Analyzer/Controller For additional information, please visit our website at www.emersonprocess.com/raihome/liquid/. ESSENTIAL
More information60W Power over Ethernet Waterproof Adapter PoE IEEE BT Single Port Injector for Outdoor Application
WWW.PHIHONG.COM 60W Power over Ethernet Waterproof Adapter PoE IEEE BT Single Port Injector for Outdoor Application Features Compliant with the IEEE802.3bt Standard Non-Vented Case with Mounting Bracket
More informationdual-line 6-dIGIt process MeteR
dual-line 6-dIGIt process MeteR ProVu Se r i e S provu Model pd6000 0-20 ma, 4-20 ma, 0-5 V, 1-5 V, and ±10 V Inputs NEMA 4X, IP65 Front Universal 85-265 VAC or 12/24 VDC Input Power Large Dual-Line 6-Digit
More informationOPERATOR S MANUAL 9000U ISOLATOR
OPERATOR S MANUAL 9000U ISOLATOR Masibus Automation And Instrumentation Pvt. Ltd. B/30, GIDC Electronics Estate, Sector-25, Gandhinagar-382044, Gujarat, India Ph: 91 79 23287275-79 Fax: 91 79 23287281,
More informationModel HU-224/225. Technical Information TI.224/ Humidity Transduce r FOR ADDITIONAL INFORMATION SEE HU-224/225 DATA SHEET
Model /225 FOR ADDITIONAL INFORMATION SEE /225 DATA SHEET SPECIFICATIONS Accuracy*: ± 2% / ± 3% RH Range: 0-100% RH Hysteresis: ± 1% Supply Voltage:12-40 VDC 12-35 VAC (VDC output units only) Supply Current:
More informationInstruction Manual Digital Differential Pressure Switch / Transmitter
DE45 Instruction Manual Digital Differential Pressure Switch / Transmitter Table of Contents 1. Safety Instructions 2. Intended Applications 3. Product Description and Functions 4. Installation 5. Commissioning
More informationSignet Pressure Transmitter
Signet 850 Pressure English *850.090* 850.090 Rev. H /06 English CAUTION! Remove power to unit before wiring input and output connections. Follow instructions carefully to avoid personal injury. Contents.
More informationMODEL SW6000 & SM6100 CENELEC INSTRUCTIONS
MODEL SW6000 & SM6100 CENELEC INSTRUCTIONS Installation Manual 1180 METRIX Experience Value 8824 Fallbrook Dr. Houston, TX 77064, USA Tel: 1-281-940-1802 After Hours Technical Assistance: 1-713-702-8805
More informationDIGITAL METERS Universal Analog Input Process Meter With Rate/Totalizer/Batch Control Features Instruction Manual
DIGITAL METERS Universal Analog Input Process Meter With Rate/Totalizer/Batch Control Features 4-20 ma, 1-5 V, 0-5 V, or 0-10 V Field Selectable Inputs Full Six Digit Display for Total, 4½ Digit + Extra
More informationTABLE OF CONTENTS INTRODUCTION. 3. Analog Input Analog Output Digital Input Digital Output OPERATIONAL DESCRIPITON.. 7 PROGRAMMING AND INITIAL SETUP.
DIVERSIFIED HEAT TRANSFER SERIES 700 STEAM GENERATOR CONTROLLER INSTRUCTION MANUAL VISIT OUR WEBSITE AT SIGMACONTROLS.COM SERIES 700 DHT STEAM GENERATOR MANUAL 042514 2 TABLE OF CONTENTS INTRODUCTION.
More informationControl IT Booster Pump Controller
Data Sheet SS/_4 Control IT Booster Pump Controller Protection for the pasteurization process ensuring a high quality, safe product for your customers High visibility LED displays continuous indication
More informationFlowJam Plus. Superior with Solids. Material flow monitor with blockage detector. Operating instructions
EN Superior FlowJam Plus Operating instructions Material flow monitor blockage detector SWR engineering Messtechnik GmbH PART OF THE ENVIRONNEMENT S.A GROUP CONTENTS Page 1. Function.................................................
More informationDigital Keypad Introduction
K2 Digital Keypad Introduction The K02 uses the latest microprocessor technology to operate door strikes and security systems that require a momentary (timed) or latching dry contact closure. All programming
More informationPneumatic Control/Feedback
897 /Feedback Type 897 can be combined with... Compact design Integrated pilot valve with manual override Internal control air routing Bright LED position indicator Automatic end position adjustment Type
More informationREDUNDANCY MODULE TSP-REM360 AND TSP-REM600
REDUNDANCY MODULE TSP-REM360 AND TSP-REM600 Operating Instructions Seite 1 Dimensions drawings: TSP-REM360 Weight: 0.882lb Gewicht: 0.40kg Seite 2 Dimensions drawings: TSP-REM600 Bottom view Top view Side
More informationData Sheet A200 Series Electric Actuators
Data Sheet Series Electric Actuators Series Electric Actuators Description Trend series actuators are used with Trend VB and SVG valves. Self stroking design minimises commissioning time and improves the
More informationProgrammable transmitter of temperature, relative humidity and other derived humidity values with 0 to 10 V outputs Instruction Manual
T0210 TRANSMITTER Programmable transmitter of temperature, relative humidity and other derived humidity values with 0 to 10 V outputs Instruction Manual Instruction manual for use of T0210 transmitter
More informationEasidew Portable Hygrometer
Easidew Portable Hygrometer A compact and easy to use portable hygrometer with fast response, integrated sampling system and traceability to National Standards. Highlights Wide measurement range Simple
More informationJUMO MIDAS C08. OEM Pressure Transmitter Basic. Applications. Brief description. Special features. Customer benefits
Data Sheet 4000 Page /0 JUMO MIDAS C08 OEM Pressure Transmitter Basic Applications compressors machinery and plant engineering industrial pneumatics commercial vehicles building technology Brief description
More informationDINALOG A 144 x 36 A1400 Light-Strip Indicator
DINALOG A x 6 A00 Light-Strip Indicator -9-0-0 /.00 Front panel dimensions: x 6 mm Light-strip indicator with 7 high-contrast LEDs Red LED display color Digital display range for portrait format: 999 to
More informationSeries P215DP Single/Dual Pressure Input Condenser Fan Speed Controllers For Single Phase Motors (incl. built-in RFI suppression filter)
PSC 0108 European Refrigeration Controls Catalogue Catalog Section 4 Product Bulletin Series Single/Dual Pressure Input Condenser Fan Speed Controllers For Single Phase Motors (incl. built-in RFI suppression
More informationJUMO MIDAS C08. OEM Pressure Transmitter Basic. Applications. Brief description. Special features. Customer benefits
sales@jumo.co.uk info.us@jumo.net Page /0 JUMO MIDAS C08 OEM Pressure Transmitter Basic Applications compressors machinery and plant engineering industrial pneumatics commercial vehicles building technology
More informationMPU-120S Series. Single Output, 180W Compact, U-Channel AC/DC Power Supplies. Key Features:
MPU-120S Series Single, 180W Compact, U-Channel AC/DC Power Supplies Key Features: 180W Power Universal 90-264 AC Power Factor Correction EN 60950 Approved Compact U-Channel Five Single Models Meets EN
More informationMulti-Point Gas Detection and Control System
Multi-Point Gas Detection and Control System DESCRIPTION Wall mounted, microprocessor-based, multi-point, analog electronic control system for various gas, temperature and humidity detection, control and
More informationControl head for hygienic process valves
for hygienic process valves Type can be combined with... Universal attachment for hygienic process valves Contactless position measurement system with 3 switching points (Teach-In function) Coloured status
More informationDM28 - Economical Digital Process and Strain Gauge Panel Meters
DM28 - Economical Digital Process and Strain Gauge Panel Meters TRANSDUCERS Easily scaled in any engineering units from -19999 to 99999 Large 18mm (.71 ) high red or green display Front panel MIN, MAX
More informationDigital Positioner 8049
Compact digital positioner for pneumatic control valves. Positioner can be integrated into valve actuator (no external moving parts for stroke feedback) Wide range of strokes - 8 mm No steady-state air
More informationRhino Redundancy Module PSM24-REM360S. Operating Instructions
Rhino Redundancy Module PSM4-REM360S Operating Instructions RHINO REDUNDANCY MODULE PSM4-REM360S Description With this module and two power supplies of the PSM series (78, 90, 56, 80 and 360 watt models),
More informationHART Density Gauge Datasheet
HART Density Gauge Datasheet PRI 160 Pavilion 11, Coxwold Way Document Number : TD0015 Revision : A Issue : 0 Date : 31/03/2004 REVISION STATUS SIGNED / DATED A Original issue R. Field C Cunningham ISSUE
More informationPP-8516 & PP Electronic Static Pressure Controllers and Transmitters for Cental Air Supply Systems General Instructions
PP-8516 & PP-8616 Electronic Static Pressure Controllers and Transmitters for Cental Air Supply Systems General Instructions Part Number PP-8516 Static Pressure Controller/Transmitter PP-8616 Static Pressure
More informationCHAPTER 1. Introduction Introduction 3
Technical & User Manual Weight Indicator: SMIT-3015 Manufactured By: Samyak Instrumentation Pvt.Ltd. F-4, Memnagar Complex, Opp.Petrol Pump, Memnagar Village, Ahmedabad, India-380052. Phone: +91-79-27495500/5600,
More informationSeries SD-3PB Digital THERMOSTAT + TIMER
SD-3PB Thermostat and Interval Timer in one Unit. This microcomputer based controller consists of two sections: The Digital Timer and Digital Thermostat, working together to control the power switched
More informationCT-1000 Leak Test System. Installation and Operation Manual
CT-1000 Leak Test System Installation and Operation Manual Table of Contents Page CT-1000 LEAK TEST SYSTEM 2 OPERATION OVERVIEW 5 SETUP MODE 7 CALIBRATION MODE 12 TEST MODE 16 PNEUMATIC CONNECTIONS 19
More informationPressure sensor For highest pressure applications to 15,000 bar Model HP-2
Pressure Pressure sensor For highest pressure applications to 15,000 bar Model HP-2 WIKA data sheet PE 81.53 for further approvals see page 6 Applications Test bench construction Water jet cutting High-pressure
More information