Installation instruction AWRON Display F22DGA

Transcription

1 Page: 1 Installation instruction AWRON Display F22DGA BMW F22 Coupé

2 Page: 2 Table of Contents Table of Contents 2 Scope of delivery 3 Toolkit 4 Cabel system 5 Schematic 6 Installation Guide Disassembly interior trim 7 Disassembly panel under the glove box on passenger side 9 Disassembly door sill on passenger side 12 Disassembly side trim on the passenger side 13 Expose the connector from the FEM control unit 14 Dismounting plug CON 3 15 Dismounting plug CON 2 16 Unpin cable from connector 17 Pin the cable into the connector 18 Plug CON 3 into the connector 20 Remove plug CON 2 21 Disassembly trim on the passenger side 22 Plug CON 10 connection 24 Remove plug CON Support & FAQs 28

3 Page: 3 Scope of delivery F2xDGA Display modul Power cord set

4 Screwdriver TORX T25 Socket wrench 10mm Flat screwdriver 2mm Installation: F22DGA Page: 4 Toolkit Mounting wedge 2mm Assembly tool

5 150cm USB Installation: F22DGA Page: 5 Cabel system

6 Page: 6 Schematic

7 Page: 7 Disassembly interior trim Remove with a plastic wedge strip the interior. Begin from the right. Pay attention to the connector on startup button and the operating unit warning lights, etc. (see picture below right) Disconnect the connectors, then you can remove air vent. With pry wedge out Gently pull the car air vent

8 Page: 8 Disassembly interior trim Threading of cables

9 Page: 9 Disassembly panel under the glove box on passenger side Unfolding the screw Hex, wrench size 8 mm Unfolding the screw Hex, wrench size 8 mm

10 Page: 10 Disassembly panel under the glove box on passenger side Remove connector

11 Page: 11 Disassembly panel under the glove box on passenger side Remove connector

12 Page: 12 Disassembly door sill on passenger side Use a plastic wedge Unclip side trim Use a plastic wedge

13 Page: 13 Disassembly side trim on the passenger side Remove the side panel Use a plastic wedge Unscrew the cover Screwdriver TORX T25

14 Page: 14 Expose the connector from the FEM control unit Remove the side panel Remove connector CON3

15 Page: 15 Dismounting plug CON 3 Unlocking bracket at the connector solve Remove connector

16 Page: 16 Dismounting plug CON 2 CON10 CON3 CON2

17 Page: 17 Unpin cable from connector Remowe connector from the case Flat screwdriver 2mm 18 = PT_CAN_LOW (rot) 19 = PT_CAN_HIGH (blau/rot) Unpin 18 and 19 Pin Flat screwdriver 2mm

18 Page: 18 Pin the cable into the connector Pin 1 = PT_CAN_LOW (rot) Pin 2 = PT_CAN_HIGH (blau/rot) Install the supplied white connector Cable red and blue / red from Pin the AWRON cable harness in chamber 18 and 19

19 Page: 19 Pin the cable into the connector

20 Page: 20 Plug CON 3 into the connector CON10 CON3 CON2

21 Page: 21 Remove plug CON 2 Unlocking bracket at the connector solve Kein Werkzeug notwendig Remove connector Kein Werkzeug notwendig

22 Page: 22 Disassembly trim on the passenger side Remowe connector from the case 20 = Kl.15 (!2V) (braun/grau) 24 = Kl.31 MASSE (braun/schwarz) Unpin 20 und 24 Pin Flachschraubenzieher 2mm

23 Page: 23 Disassembly trim on the passenger side Pin 1 = Kl.15 (12V) (grün/grau) Pin 2 = Kl.31 MASSE (braun/schwarz) Install the supplied black connector Cable green / brown and brown / black from Pin AWRON cable harness in chamber 20 and 24

24 Page: 24 Plug CON 10 connection CON10 CON3 CON2

25 Page: 25 Remove plug CON 10 Unlocking bracket at the connector solve Remove connector 19 18

26 Page: 26 Remove plug CON 10 Remowe connector from the case Unpin Pin 3 Flachschraubenzieher 2mm

27 Page: 27 Remove plug CON 10 Pin 1 = ETH_WUP (blau/gelb) Install the supplied blue connector 19 18

28 Page: 28 Support & FAQs For all enquiries concerning your AWRON display system, or if you have problems with installation guide the AWRON support team at are at your service. Please also seen us and our another AWRON products on our website