ODOT ITB Section 4: Flashers, Timers, & Software Systems Item 4-1

Transcription

1 ODOT ITB Item 4-1

2 DATA SHEET SSF-86-3 ODOT ITB Item 4-1 Solid State Flasher: Description: The PDC model SSF-86 solid state flasher is a dual circuit flasher designed for the Traffic Control Industry. This unit is conservatively rated up to 20 A per circuit. The flash rate is flashes per minute and does not vary due to voltage or temperature variations. With the zero voltage switching design, there are no contacts to wear out or deteriorate due to arcing or corrosion. Also, extended life of the bulbs can be expected as well as reduced Radio Frequency Interference (RFI). The extruded aluminum heatsink provides more than adequate heat dissipation. Connector Pinout: Mates with a Beau P-5406-LAB or equivalent Electrical Characteristics: Zero voltage turn on Zero voltage turn off Tungsten Lamp or Gas Tubing Transformer load- Operating Voltage Mechanical V +-5 degrees 0A +-5 degrees Up to 20 A max VAC Length 8.40 inches Width.1.70 inches Height 4.18 inches Weight lbs Operating Temperature : Full load from 35 to +74 degrees C Guarantee: The flasher is fully guaranteed against all failures due to manufacturing defects for two years. P.O. Box 7172 #205, Stateline, NV PH (925) FAX (925)

3 ODOT ITB Item 4-2

4 DATA SHEET SSF-86-3 ODOT ITB Item 4-2 Solid State Flasher: Description: The PDC model SSF-86 solid state flasher is a dual circuit flasher designed for the Traffic Control Industry. This unit is conservatively rated up to 20 A per circuit. The flash rate is flashes per minute and does not vary due to voltage or temperature variations. With the zero voltage switching design, there are no contacts to wear out or deteriorate due to arcing or corrosion. Also, extended life of the bulbs can be expected as well as reduced Radio Frequency Interference (RFI). The extruded aluminum heatsink provides more than adequate heat dissipation. Connector Pinout: Mates with a Beau P-5406-LAB or equivalent Electrical Characteristics: Zero voltage turn on Zero voltage turn off Tungsten Lamp or Gas Tubing Transformer load- Operating Voltage Mechanical V +-5 degrees 0A +-5 degrees Up to 20 A max VAC Length 8.40 inches Width.1.70 inches Height 4.18 inches Weight lbs Operating Temperature : Full load from 35 to +74 degrees C Guarantee: The flasher is fully guaranteed against all failures due to manufacturing defects for two years. P.O. Box 7172 #205, Stateline, NV PH (925) FAX (925)

5 AP21 SERIES TIME SWITCH ODOT ITB Item character, alpha-numeric, Liquid Crystal Display (LCD) Laptop Programmable with 21PC Software Daylight Savings Time entered from the keyboard 48-hour capacitive back-up, no batteries Auto Prompt for user friendly programming 16 Powerful Program Steps AP21 AC/DC Powered 10 Skip Plans for Holidays 15 Amp relay output Program Transfer from unit to unit (AP21T & AP21TR) Laptop Computer Programmable using the 21PC Software AP21T AC/DC Powered with Program Transfer AP21 s are AC/DC, AP21T s are AC/DC, AP21TR s are AC only AP21TRDC s are DC only AP21TR AP21TRDC Compact Size: 2" x 2 1/2" x 4" Smallest Time Switch ever built for Traffic Applications (AP21TR) RTC Manufacturing, Inc. Serving the traffic signal industry since

6 AP21 SERIES TIME SWITCH The family of AP21's are single circuit, calendar programmable solid state time switches. They are used for switching electric circuits according to a pre-set time and date program. The AP21's AUTO PROMPTING alpha-numeric display makes programming fast and simple. Program transfer can be accomplished by using a Laptop Computer or an AP21T. The AP21TR is only 2 x 2 1/2 x 4 making it the smallest time switch ever designed specifically for traffic applications. The AP21 and AP21T draw their power from any 120VAC or 12VDC supply. The AP21TR is 120VAC powered and the AP21TRDC is 12VDC powered. STANDARD FEATURES 16 character, alpha-numeric, easy to read Liquid Crystal Display (LCD). Optional back-lit display available. Automatic Daylight Savings Time (DST) compensation. DST data entered from keyboard - makes future DST changes quick and easy. Time of Day entered in 12-hour format. Automatic Leap Year compensation. 48-hour capacitive memory back-up - no batteries to replace. SPECIFICATIONS Display character, Apha-Numeric, Liquid Crystal Display (LCD), Back-lit Display Optional Keyboard Key, Positive Action Push Button Back-up Power Hour Capacitive Electrical Connection...Terminal Block (#12 to #20 AWG) or CPC Connector with Harness (optional) Output SPDT Relay Rated at 15 Amps 115 VAC Resistive Load Line Voltage to 135VAC, 60 HZ and 12VDC Time Base AC Powered (power line) Back-up and DC Powered +/-.005% Crystal Size h x 3.7 w x 1.55 d (AP21) 8.0 h x 3.7 w x 1.55 d (AP21T) 2.0 x 2.5 x 4.0 (AP21TR) Temperature Range to +74 Degrees C The display "Auto Prompts" the operator through the programming process - very user friendly. 16 powerful program steps. Single Day, Week End, Week Day, or Every Day programming capability for each program step. 10 Skip Plans - Each skip plan prevents the time switch output from activating on a specific day or consecutive days. Program Transfer from one AP21T to another, or from an AP21T to an AP21TR (AC or DC). Laptop Computer Programmable - using the 21PC Software. SPDT Relay Output rated at 15 Amps at 115 VAC resistive load. AP21 and AP21T s work on 120VAC and 12VDC power sources. ORDERING INFORMATION Part Number Description AP21 Single Circuit Time Switch AP21T Single Circuit Time Switch with Transfer AP21TR Single Circuit Time Switch (2" x 2.5" x 4") AP21TRDC 12VDC Version of AP21TR 21PC Laptop Programming Software & Cables EL Electro-Luminescent (back-lit) Display CPC Connector with 48" Wiring Harness CPC Connector with 72" Wiring Harness Program Transfer Cable NOTE: All AP21 and AP21T s are AC and DC powered, AP21TR is AC and AP21TRDC is DC powered. RTC Manufacturing, Inc. P. O. Box * Arlington, TX (800) (817) (800) fax (817) fax Serving the traffic signal industry since

7 ODOT ITB Item 4-3

8

9 ODOT ITB Item 4-3 Traffic Signaling Products ACP VAC / 1 Phase / Filtered The ACP-340 filtering surge protector absorbs power line noise and switching transients that other suppressors and RFI filters pass through. In addition, this unit offers better lightning protection than the standard SHP The ACP-340 can replace the RFI filter when high attenuation of noise above 25 MHz is not required. If random time-base, memory loss, or other problems are affecting some of your intersections, this state-of-the-art protector can be of great benefit when properly installed. Keeping You Connected! CAUTION 1 This product could become excessively hot and rupture in the rare event of power line conditions or surge that exceeds its rated operating specification. Appropriate precautions should be exercised. 2 High voltages are present on electrical termination. Unit should be serviced by qualified personnel only. Peak Current (8x20μs) Life Test Clamp Voltage Response Time Continuous Service Current Dimensions (LxWxH, not incl. GND) Operating Temperature SPECIFICATIONS 20,000 Amps* 5% change (voltage clamp before and after 25 surges of 20kA waveshape) 250V 20 ka voltage never exceeds 250V during surge 10 Amps max. 120VAC, 60Hz 7.15 in. x 3.13 in. x 2.3 in. 40 C to +85 C * Tested with MAIN NEUTRAL strapped to ground NEED HELP? Call N.E. 19th Avenue P.O. Box 1778 Ocala, Florida (352) FAX (352) Sales: us at: edco@edcosurge.com Internet: Page 1

10 Traffic Signaling Products ACP VAC / 1 Phase / Filtered INSTALLATION Keeping You Connected! MOUNTING NEED HELP? Call N.E. 19th Avenue P.O. Box 1778 Ocala, Florida (352) FAX (352) Sales: us at: edco@edcosurge.com Internet: Page 2

11 AP21 SERIES TIME SWITCH ODOT ITB Item character, alpha-numeric, Liquid Crystal Display (LCD) Laptop Programmable with 21PC Software Daylight Savings Time entered from the keyboard 48-hour capacitive back-up, no batteries Auto Prompt for user friendly programming 16 Powerful Program Steps AP21 AC/DC Powered 10 Skip Plans for Holidays 15 Amp relay output Program Transfer from unit to unit (AP21T & AP21TR) Laptop Computer Programmable using the 21PC Software AP21T AC/DC Powered with Program Transfer AP21 s are AC/DC, AP21T s are AC/DC, AP21TR s are AC only AP21TRDC s are DC only AP21TR AP21TRDC Compact Size: 2" x 2 1/2" x 4" Smallest Time Switch ever built for Traffic Applications (AP21TR) RTC Manufacturing, Inc. Serving the traffic signal industry since

12 AP21 SERIES TIME SWITCH The family of AP21's are single circuit, calendar programmable solid state time switches. They are used for switching electric circuits according to a pre-set time and date program. The AP21's AUTO PROMPTING alpha-numeric display makes programming fast and simple. Program transfer can be accomplished by using a Laptop Computer or an AP21T. The AP21TR is only 2 x 2 1/2 x 4 making it the smallest time switch ever designed specifically for traffic applications. The AP21 and AP21T draw their power from any 120VAC or 12VDC supply. The AP21TR is 120VAC powered and the AP21TRDC is 12VDC powered. STANDARD FEATURES 16 character, alpha-numeric, easy to read Liquid Crystal Display (LCD). Optional back-lit display available. Automatic Daylight Savings Time (DST) compensation. DST data entered from keyboard - makes future DST changes quick and easy. Time of Day entered in 12-hour format. Automatic Leap Year compensation. 48-hour capacitive memory back-up - no batteries to replace. SPECIFICATIONS Display character, Apha-Numeric, Liquid Crystal Display (LCD), Back-lit Display Optional Keyboard Key, Positive Action Push Button Back-up Power Hour Capacitive Electrical Connection...Terminal Block (#12 to #20 AWG) or CPC Connector with Harness (optional) Output SPDT Relay Rated at 15 Amps 115 VAC Resistive Load Line Voltage to 135VAC, 60 HZ and 12VDC Time Base AC Powered (power line) Back-up and DC Powered +/-.005% Crystal Size h x 3.7 w x 1.55 d (AP21) 8.0 h x 3.7 w x 1.55 d (AP21T) 2.0 x 2.5 x 4.0 (AP21TR) Temperature Range to +74 Degrees C The display "Auto Prompts" the operator through the programming process - very user friendly. 16 powerful program steps. Single Day, Week End, Week Day, or Every Day programming capability for each program step. 10 Skip Plans - Each skip plan prevents the time switch output from activating on a specific day or consecutive days. Program Transfer from one AP21T to another, or from an AP21T to an AP21TR (AC or DC). Laptop Computer Programmable - using the 21PC Software. SPDT Relay Output rated at 15 Amps at 115 VAC resistive load. AP21 and AP21T s work on 120VAC and 12VDC power sources. ORDERING INFORMATION Part Number Description AP21 Single Circuit Time Switch AP21T Single Circuit Time Switch with Transfer AP21TR Single Circuit Time Switch (2" x 2.5" x 4") AP21TRDC 12VDC Version of AP21TR 21PC Laptop Programming Software & Cables EL Electro-Luminescent (back-lit) Display CPC Connector with 48" Wiring Harness CPC Connector with 72" Wiring Harness Program Transfer Cable NOTE: All AP21 and AP21T s are AC and DC powered, AP21TR is AC and AP21TRDC is DC powered. RTC Manufacturing, Inc. P. O. Box * Arlington, TX (800) (817) (800) fax (817) fax Serving the traffic signal industry since

13 ODOT ITB Item 4-4

14

15 ODOT ITB Item 4-4 Traffic Signaling Products ACP VAC / 1 Phase / Filtered The ACP-340 filtering surge protector absorbs power line noise and switching transients that other suppressors and RFI filters pass through. In addition, this unit offers better lightning protection than the standard SHP The ACP-340 can replace the RFI filter when high attenuation of noise above 25 MHz is not required. If random time-base, memory loss, or other problems are affecting some of your intersections, this state-of-the-art protector can be of great benefit when properly installed. Keeping You Connected! CAUTION 1 This product could become excessively hot and rupture in the rare event of power line conditions or surge that exceeds its rated operating specification. Appropriate precautions should be exercised. 2 High voltages are present on electrical termination. Unit should be serviced by qualified personnel only. Peak Current (8x20μs) Life Test Clamp Voltage Response Time Continuous Service Current Dimensions (LxWxH, not incl. GND) Operating Temperature SPECIFICATIONS 20,000 Amps* 5% change (voltage clamp before and after 25 surges of 20kA waveshape) 250V 20 ka voltage never exceeds 250V during surge 10 Amps max. 120VAC, 60Hz 7.15 in. x 3.13 in. x 2.3 in. 40 C to +85 C * Tested with MAIN NEUTRAL strapped to ground NEED HELP? Call N.E. 19th Avenue P.O. Box 1778 Ocala, Florida (352) FAX (352) Sales: us at: edco@edcosurge.com Internet: Page 1

16 Traffic Signaling Products ACP VAC / 1 Phase / Filtered INSTALLATION Keeping You Connected! MOUNTING NEED HELP? Call N.E. 19th Avenue P.O. Box 1778 Ocala, Florida (352) FAX (352) Sales: us at: edco@edcosurge.com Internet: Page 2

17 AP22 TIME SWITCH 2-Way Radio / Cellular / Ethernet / Wi-Fi ODOT ITB Item 4-4 The AP22 Time Switch is a two-circuit, calendar programmable solid state time switch. It is used for switching electric circuits according to a pre-set time and date program. It has the ability to run up to ten different day plans and thirty-six different annual exception plans to accommodate different school calendars and/or traffic patterns throughout the year. The AP22 auto prompting alpha-numeric display makes programming fast and simple. Upload and download programming via 2-Way Radio, Cellular, Ethernet, Wi-Fi or Laptop. RTC-Traffic.com contact our team at Info@RTC-Traffic.com for more information TOLL-FREE FAX RTC Manufacturing, Inc., 1016 Enterprise Place, Arlington, Texas RTC Manufacturing, Inc. All Rights Reserved.

18 AP22 TIME SWITCH 2-Way Radio / Cellular / Ethernet / Wi-Fi AP22 SPECIFICATIONS DESCRIPTION Upload and download programming via 2-Way Radio, Cellular, Ethernet, Wi-Fi or Laptop. DISPLAY KEYBOARD BACK-UP POWER OUTPUT POWER TIME BASE Two-line, 16 characters per line Liquid Crystal Display (LCD) Sixteen-key, positive action push button Non-volatile memory Two SPDT relays rated at 15 amps 12VDC or 115 VAC resistive load Less than 0.25 Watt at rest, 0.6 watt with relay ON, 12VDC AC Power = 60Hz power line DC Power = Temperature-compensated crystal with accuracy of.35 seconds/day SIZE 10 3/8"h x 4 3/4"w x 2"d TEMPERATURE RANGE -30 to +74 Celsius AP22 FEATURES Two-line, sixteen-character, Liquid Crystal Display (LCD) Automatic Daylight Saving Time adjustments Program memory stored for years - no batteries to replace The user-friendly display auto-prompts the operator through the programming process Ten day plans, sixteen program steps per plan accommodate standard school day, school holidays, early dismissal days, summer school days, etc. Standard week plan programming uses any day plan for the most complicated school schedule Thirty-six annual programs use exception-day programming to assign any day plan to any calendar day(s) Two independent 15-amp relay outputs Program transfers from unit to unit Works on 120VAC and 12VDC power sources AP22 ORDERING INFORMATION PART NUMBER DESCRIPTION Two-output time switch with CPC connector and 48" wiring harness Program transfer cable AC power cable with connector The AP22 Meets NEMA TS1/TS2 Requirements RTC-Traffic.com contact our team at Info@RTC-Traffic.com for more information TOLL-FREE FAX RTC Manufacturing, Inc., 1016 Enterprise Place, Arlington, Texas RTC Manufacturing, Inc. All Rights Reserved

19 AP22 TIME SWITCH 2-Way Radio / Cellular / Ethernet / Wi-Fi ODOT ITB Item 4-5 The AP22 Time Switch is a two-circuit, calendar programmable solid state time switch. It is used for switching electric circuits according to a pre-set time and date program. It has the ability to run up to ten different day plans and thirty-six different annual exception plans to accommodate different school calendars and/or traffic patterns throughout the year. The AP22 auto prompting alpha-numeric display makes programming fast and simple. Upload and download programming via 2-Way Radio, Cellular, Ethernet, Wi-Fi or Laptop. RTC-Traffic.com contact our team at Info@RTC-Traffic.com for more information TOLL-FREE FAX RTC Manufacturing, Inc., 1016 Enterprise Place, Arlington, Texas RTC Manufacturing, Inc. All Rights Reserved.

20 AP22 TIME SWITCH 2-Way Radio / Cellular / Ethernet / Wi-Fi AP22 SPECIFICATIONS DESCRIPTION Upload and download programming via 2-Way Radio, Cellular, Ethernet, Wi-Fi or Laptop. DISPLAY KEYBOARD BACK-UP POWER OUTPUT POWER TIME BASE Two-line, 16 characters per line Liquid Crystal Display (LCD) Sixteen-key, positive action push button Non-volatile memory Two SPDT relays rated at 15 amps 12VDC or 115 VAC resistive load Less than 0.25 Watt at rest, 0.6 watt with relay ON, 12VDC AC Power = 60Hz power line DC Power = Temperature-compensated crystal with accuracy of.35 seconds/day SIZE 10 3/8"h x 4 3/4"w x 2"d TEMPERATURE RANGE -30 to +74 Celsius AP22 FEATURES Two-line, sixteen-character, Liquid Crystal Display (LCD) Automatic Daylight Saving Time adjustments Program memory stored for years - no batteries to replace The user-friendly display auto-prompts the operator through the programming process Ten day plans, sixteen program steps per plan accommodate standard school day, school holidays, early dismissal days, summer school days, etc. Standard week plan programming uses any day plan for the most complicated school schedule Thirty-six annual programs use exception-day programming to assign any day plan to any calendar day(s) Two independent 15-amp relay outputs Program transfers from unit to unit Works on 120VAC and 12VDC power sources AP22 ORDERING INFORMATION PART NUMBER DESCRIPTION Two-output time switch with CPC connector and 48" wiring harness Program transfer cable AC power cable with connector The AP22 Meets NEMA TS1/TS2 Requirements RTC-Traffic.com contact our team at Info@RTC-Traffic.com for more information TOLL-FREE FAX RTC Manufacturing, Inc., 1016 Enterprise Place, Arlington, Texas RTC Manufacturing, Inc. All Rights Reserved

21 AP21 SERIES TIME SWITCH ODOT ITB Item character, alpha-numeric, Liquid Crystal Display (LCD) Laptop Programmable with 21PC Software Daylight Savings Time entered from the keyboard 48-hour capacitive back-up, no batteries Auto Prompt for user friendly programming 16 Powerful Program Steps AP21 AC/DC Powered 10 Skip Plans for Holidays 15 Amp relay output Program Transfer from unit to unit (AP21T & AP21TR) Laptop Computer Programmable using the 21PC Software AP21T AC/DC Powered with Program Transfer AP21 s are AC/DC, AP21T s are AC/DC, AP21TR s are AC only AP21TRDC s are DC only AP21TR AP21TRDC Compact Size: 2" x 2 1/2" x 4" Smallest Time Switch ever built for Traffic Applications (AP21TR) RTC Manufacturing, Inc. Serving the traffic signal industry since

22 AP21 SERIES TIME SWITCH The family of AP21's are single circuit, calendar programmable solid state time switches. They are used for switching electric circuits according to a pre-set time and date program. The AP21's AUTO PROMPTING alpha-numeric display makes programming fast and simple. Program transfer can be accomplished by using a Laptop Computer or an AP21T. The AP21TR is only 2 x 2 1/2 x 4 making it the smallest time switch ever designed specifically for traffic applications. The AP21 and AP21T draw their power from any 120VAC or 12VDC supply. The AP21TR is 120VAC powered and the AP21TRDC is 12VDC powered. STANDARD FEATURES 16 character, alpha-numeric, easy to read Liquid Crystal Display (LCD). Optional back-lit display available. Automatic Daylight Savings Time (DST) compensation. DST data entered from keyboard - makes future DST changes quick and easy. Time of Day entered in 12-hour format. Automatic Leap Year compensation. 48-hour capacitive memory back-up - no batteries to replace. SPECIFICATIONS Display character, Apha-Numeric, Liquid Crystal Display (LCD), Back-lit Display Optional Keyboard Key, Positive Action Push Button Back-up Power Hour Capacitive Electrical Connection...Terminal Block (#12 to #20 AWG) or CPC Connector with Harness (optional) Output SPDT Relay Rated at 15 Amps 115 VAC Resistive Load Line Voltage to 135VAC, 60 HZ and 12VDC Time Base AC Powered (power line) Back-up and DC Powered +/-.005% Crystal Size h x 3.7 w x 1.55 d (AP21) 8.0 h x 3.7 w x 1.55 d (AP21T) 2.0 x 2.5 x 4.0 (AP21TR) Temperature Range to +74 Degrees C The display "Auto Prompts" the operator through the programming process - very user friendly. 16 powerful program steps. Single Day, Week End, Week Day, or Every Day programming capability for each program step. 10 Skip Plans - Each skip plan prevents the time switch output from activating on a specific day or consecutive days. Program Transfer from one AP21T to another, or from an AP21T to an AP21TR (AC or DC). Laptop Computer Programmable - using the 21PC Software. SPDT Relay Output rated at 15 Amps at 115 VAC resistive load. AP21 and AP21T s work on 120VAC and 12VDC power sources. ORDERING INFORMATION Part Number Description AP21 Single Circuit Time Switch AP21T Single Circuit Time Switch with Transfer AP21TR Single Circuit Time Switch (2" x 2.5" x 4") AP21TRDC 12VDC Version of AP21TR 21PC Laptop Programming Software & Cables EL Electro-Luminescent (back-lit) Display CPC Connector with 48" Wiring Harness CPC Connector with 72" Wiring Harness Program Transfer Cable NOTE: All AP21 and AP21T s are AC and DC powered, AP21TR is AC and AP21TRDC is DC powered. RTC Manufacturing, Inc. P. O. Box * Arlington, TX (800) (817) (800) fax (817) fax Serving the traffic signal industry since

23 M2M CELLULAR COMMUNICATIONS MODEM Communicates With School Zone Flashers Using SMS Texting The RTC Model TSC2G is a compact communications modem that allows the user to connect an RTC Time Switch to a central computer using SMS texting. The TSC2G provides full, two-way communications from a central ODOT ITB Section 4: Flashers, Timers, & Software Systems Item 4-9 computer to any Model AP22 or CPR2102 Time Switch via SMS texting eliminating the need for any additional infrastructure. RTC-Traffic.com contact our team at Info@RTC-Traffic.com for more information TOLL-FREE FAX RTC Manufacturing, Inc., 1016 Enterprise Place, Arlington, Texas RTC Manufacturing, Inc. All Rights Reserved.

24 M2M CELLULAR COMMUNICATIONS MODEM Communicates With School Zone Flashers Using SMS Texting M2M FEATURES Two-way communication with AP22 and CPR2102 time switches using SMS texting (no additional infrastructure required) Omni antenna typically mounts inside the flasher cabinet, an external Omni antenna is available if required LED indicator for power and SMS network connection Compact size: 3.4"w x 2.4"h x 1"d with mounting tabs Simple, plug-and-play operation Make program changes anytime day or night Operating temperature range: -30 to +75 Celsius M2M SPECIFICATIONS DESCRIPTION DIMENSIONS 3.4"w x 2.4"h x 1"d POWER OPERATING TEMPERATURE SMS ANTENNA OPTIONS PROGRAMMING MANUAL CONTROL VALIDATE PROGRAMMING 12VDC, powered from DB9 on time switch -30 to +75 Celsius Short Message Service Omni antenna mounted inside the flasher cabinet (standard) Omni antenna mounted outside the flasher cabinet (if required) Make programming changes to your school zone flashers anytime from a PC or laptop connected to the internet Send manual control commands at anytime, day or night Validate the program in any time switch at anytime, day or night GPS Time sync reference and map location services M2M SERVICE PLANS: Choose from a 5-year or 10-year service agreement RTC-Traffic.com contact our team at Info@RTC-Traffic.com for more information TOLL-FREE FAX RTC Manufacturing, Inc., 1016 Enterprise Place, Arlington, Texas RTC Manufacturing, Inc. All Rights Reserved