Propeller. Chapter 13. Airplane. A. Base for Blade. Step 1. Click File Menu > New, click Part and OK.
|
|
- Peter Nichols
- 6 years ago
- Views:
Transcription
1 Chapter 13 Airplane Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch toolbar, Fig. 1. from the Content Step 3. Click Ellipse on the Sketch toolbar. Fig. 1 Step 4. Starting from the Origin draw ellipse, Fig. 2. To draw ellipse, click Origin to place the center of the ellipse. Drag out and click to set the major axis. Drag down and click again to set the minor axis. Origin Fig. 2 Step 5. Click Smart Dimension (S) on the Sketch toolbar. Step 6. Dimension ellipse as shown in Fig. 3. To Smart dimension click the major axis points, then move the cursor up off the sketch and click. Key-in.2 for the dimension and press ENTER. Dimension the minor diameter.03. Step 7. Click Exit Sketch Sketch toolbar. on the Fig. 3 B. Save as "PROPELLER". Step 1. Click File Menu > Save As. Step 2. Key-in PROPELLER for the filename and press ENTER. SolidWorks 12 PROPELLER AIRPLANE Page /18/12
2 C. Create Plane. Step 1. Click Isometric toolbar. (Ctrl-7) on the View Step 2. Click Top Plane Manager, Fig. 4. in the Feature Step 3. Use Z key to zoom out, Fig. 5. Step 4. Ctrl drag Top plane in drawing area up and release, Fig. 6. To Ctrl drag, hold down Ctrl and drag plane up. Step 5. In the Plane Property Manager set: Distance 1.6 and press ENTER, Fig. 7 Fig. 4 Drag up set distance to 1.6 Fig. 5 click Zoom to Fit View toolbar on the the new plane should be above sketch, Fig. 9, if in wrong direction, check Flip, Fig. 7 D. Create Sketch in Plane 1. Step 1. Click Plane 1 in the Feature Manager Hold down Ctrl drag plane Fig. 6 Fig. 7 Draw Point at Origin and click Sketch toolbar, Fig. 8. from the Content Step 2. Click Point (S) on the Sketch toolbar. Step 3. Draw a Point at the Origin in Plane 1, Fig. 9. Don't draw any extra Points. Fig. 8 Step 4. Click Exit Sketch on the Sketch toolbar. Step 5. Save. Use Ctrl-S. SolidWorks 12 PROPELLER AIRPLANE Page 13-2 Fig. 9
3 E. Loft Surface. Step 1. Click Features Step 2. Click Lofted Boss/Base on the Command Manager toolbar. on the Features toolbar. Step 3. In the Surface-Loft Property Manager: under Profiles click: Point in Sketch2 Ellipse in Sketch1, Fig. 11 click Front toolbar. (Ctrl-1) on the Standard Views expand Start/End Constraints, Fig. 10 under Start/End Constraints: set Start constraint: Normal to Profile set Start Tangent Length: 10 set End constraint: Normal to Profile set End Tangent Length: 2.5 Fig. 10 Fig. 11 Fig. 12 F. Hide Plane1. Step 1. Click Isometric on the View toolbar. Step 2. Plane1 in Feature Manager click Hide on the Content menu, Fig. 13. Fig. 13 G. Flex Blade. Step 1. Click Insert Menu > Features > Flex. Step 2. In the Flex Property Manager: under Flex Input click the Loft in drawing area click Twisting, Fig. 14 set Angle under Triad -40 degrees: set Y Rotation Origin 1.1 Fig. 15 Fig. 16 SolidWorks 12 PROPELLER AIRPLANE Page 13-3 Fig. 14
4 H. Hub. Step 1. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 17. Step 2. Click Normal To toolbar. (Ctrl-8) Step 3. Click Circle on the Standard Views (S) on the Sketch toolbar. Fig. 17 Step 4. Draw a circle for the hub starting at Origin, Fig. 18. Step 5. Click Smart Dimension (S) on the Sketch toolbar. Origin Fig. 18 Step 6. Dimension circle diameter.5 as shown in Fig. 18. I. Extrude Hub. Step 1. Click Features on the Command Manager toolbar. Step 2. Click Extruded Boss/Base on the Features toolbar. Step 3. Click Isometric on the View toolbar. (Ctrl-7) Step 4. In the Property Manager set: under Direction 1 End Condition to Mid Plane Depth to.22 click OK, Fig. 19 and Fig. 20. Step 5. Save. Use Ctrl-S. Fig. 19 Fig. 20 SolidWorks 12 PROPELLER AIRPLANE Page 13-4
5 J. Fillet Edges of Blade. Step 1. Click Fillet toolbar. on the Features Step 2. In the Fillet Property Manager set: Radius to.03 click edge of blade at hub, Fig. 22 Fig. 21 Step 3. Save. Use Ctrl-S. K. Circular Pattern for Blade. Step 1. Click View Menu > Temporary Axes. (Alt-V X) Fig. 22 Fig. 23 Step 2. Click Circular Pattern in the Linear Blade Pattern flyout on the Features toolbar. Be sure to click the flyout arrow to select Circular Pattern. Step 3. In the Circular Pattern Property Manager set: under Parameters, Pattern Axis click Temp axis in drawing, Fig. 25 Axis Fillet Number of Instances to 3 Fig. 25 check Equal spacing, Fig. 24 under Features to Pattern click blade and fillet, Fig. 25 under Options check Geometry pattern, Fig. 24 click OK, Fig. 26. Fig. 24 Fig. 26 SolidWorks 12 PROPELLER AIRPLANE Page 13-5
6 L. Hole. Step 1. Turn off Temporary Axes. Click View Menu > Temporary Axes. (Alt-V X) Step 2. Rotate view to view rear face of hub as shown in Fig. 27. To rotate, hold down middle mouse button (wheel) and drag. on the Con- Step 3. Click rear face of hub and click Sketch tent menu, Fig. 27. Fig. 27 Rear face Step 4. Click Normal To on the Standard Views toolbar. Step 5. Click Circle on the Sketch toolbar. Step 6. Draw a circle for the hole starting at the Origin, Fig. 28. Step 7. Click Smart Dimension Sketch toolbar. (S) on the Step 8. Dimension the diameter.08 as shown in Fig. 28. Fig. 28 Step 9. Click Features on the Command Manager toolbar. Step 10. Click Extruded Cut on the Features toolbar. Step 11. In the Property Manager set: Depth to.2 click OK, Fig. 29 and Fig. 30. Step 12. Save. Use Ctrl-S. Fig. 29 Fig. 30 SolidWorks 12 PROPELLER AIRPLANE Page 13-6
7 M. Dome Front Face of Hub. Step 1. Click Isometric on the View toolbar. (Ctrl-7) Step 2. Click Dome Features toolbar. on the Front face Step 3. In the Dome Property Manager set: click front face of hub, Fig. 31. Distance to.1 check Elliptical dome Fig. 31 Step 4. Save. Use Ctrl-S. Fig. 32 N. Material POM Acetal Copolymer. Step 1. Right click Material and click Edit Material. in the Feature Manager Step 2. Expand Plastics in the material tree and select POM Acetal Copolymer. Click Apply and Close. Fig. 33 Step 3. Save. Use Ctrl-S. O. Insert Propeller into Assembly. Step 1. Open your ASSEMBLY file. Step 2. Click Insert Components on the Assembly toolbar. Step 3. Browse and place PROPELLER as positioned in Fig. 34. P. Mate: Prop and Motor Shaft. Step 1. Zoom in on Propeller hub and Motor shaft, Fig. 35. To zoom, hold down Shift key and drag middle mouse button (wheel). To pan, hold down Ctrl key and drag middle mouse button (wheel). Fig. 34 Step 2. Click Mate on the Assembly toolbar. Zoom Fig. 35 SolidWorks 12 PROPELLER AIRPLANE Page 13-7
8 Step 3. Right click the dome of propeller and click Select Other from the menu, Fig. 36. Step 4. Click the bottom flat face of the hole in hub and flat face of the of motor shaft, Fig. 37. Step 5. Click Add/Finish Mate to add Coincident mate. Step 6. Right click the dome of propeller and click Select Other from the menu, Fig. 38. Step 7. Click the cylindrical face of propeller hole and cylindrical face of motor shaft, Fig. 39. Step 8. Click Add/Finish Mate to add a Concentric mate. Right click face Fig. 36 Right click face Fig. 38 Fig. 37 Fig. 39 Step 9. Click OK Manager. in the Property Step 10. Save. Use Ctrl-S. SolidWorks 12 PROPELLER AIRPLANE Page 13-8
Delta Dart. Propeller. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. on the Sketch toolbar.
Chapter 8 Delta Dart Propeller A. Base for Blade. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationTail Hook. Chapter 14. Airplane. A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK.
Chapter 14 Airplane Tail Hook A. Construction Rectangle. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right (plane) in the Feature Manager and click Sketch from the Content toolbar,
More informationWheel GT-F. Chapter 5. CO2 Shell Car. A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK.
Chapter 5 CO2 Shell Car Wheel GT-F A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1.
More informationCO2 Rail Car. Wheel Rear Px. on the Command Manager toolbar.
Chapter 6 CO2 Rail Car Wheel Rear Px A. Sketch Construction Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front (plane) in the Feature Manager (left panel), Fig. 1. Step
More informationAirplane Assembly. SolidWorks 10 ASSEMBLY AIRPLANE Page 9-1
Chapter 9 A. Insert Parts. Airplane Assembly Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the Property Manager,
More informationDelta Dart. Socket. (L) on the Sketch toolbar. Fig. 1. (S) on the Sketch toolbar. on the Sketch toolbar. on the Standard Views toolbar.
Chapter 6 Delta Dart Socket A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step
More informationSkateboard. Hanger. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Fig. 2
Chapter 3 Skateboard Hanger A. Sketch1 Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationPanel. Chapter 16. Solar Car. A. Sketch. Step 1. Click File Menu > New, click Part and OK. B. Save as "PANEL". Step 1. Click File Menu > Save As.
Chapter 16 Solar Car Panel A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Center
More informationChair. Top Rail. on the Standard Views toolbar. (Ctrl-7) on the Weldments toolbar. at bottom left corner of display to deter- mine sketch plane.
Chapter 7 A. 3D Sketch. Step 1. If necessary, open your CHAIR file. Chair Top Rail Step 2. Click Isometric on the Standard Views toolbar. (Ctrl-7) Step 3. Zoom in around top of back leg, Fig. 1. To zoom,
More informationF1 Car. Wheel. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. (S) on the
Chapter 3 F1 Car Wheel A. Sketch Lines. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. Step 3.
More informationSimple Machines. Wheel. in the Feature Manager and click Sketch. on the Command Manager toolbar.
Chapter 3 Simple Machines Wheel A. Wheel. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step 3. Click
More informationFuselage and Sharks Tooth
Chapter 4 Glider Fuselage and Sharks Tooth A. Save as "FUSELAGE". Step 1. Open your FUSELAGE BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in FUSELAGE for the filename and press ENTER. B.
More informationSolar Car. Chassis. in the Feature Manager and click Sketch from the Content toolbar, Fig. 2. Origin. on the Command Manager toolbar. Fig.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Solar Car Chassis Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Chassis. Step 1. Click Right Plane in the Feature Manager and click
More informationSkateboard. Hanger. in the Feature Manager and click Sketch. (S) on the Sketch. Line
Chapter 3 Skateboard Hanger A. Sketch 1. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Right Plane from the Content toolbar, Fig. 1. in the Feature Manager and click Sketch Step
More informationBody. Chapter 1. Simple Machines. A. New Part. Step 1. Click File Menu > New.
Chapter 1 A. New Part. Step 1. Click File Menu > New. Simple Machines Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature
More informationBattery Holder 2 x AA
Chapter 22 JSS Battery Holder 2 x AA A. Front Extrude. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch from the Context toolbar,
More informationCO2 Shell Car. Axle Retainer. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig.
Chapter 17 CO2 Shell Car Axle Retainer A. Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch from the Content toolbar, Fig.
More informationBody. Chapter 2. CO2 Rail Car E. A. Save as "BODY RAIL E". Step 1. Open your BLANK file.
Chapter 2 A. Save as "BODY RAIL E". Step 1. Open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY RAIL E for the filename and press ENTER. CO2 Rail Car E Body B. Appearance. Step
More informationSpeedway. Body. (S) on the Sketch toolbar. Fig. 1
Chapter 1 A. New Part. Step 1. Click File Menu > New. Speedway Body Step 2. Click Part from the list and click OK, Fig. 1. B. Sketch Construction Rectangle. Step 1. Click Right Plane in the Feature Manager
More informationFig. 1. Fig. 1. on the Standard Views toolbar. SolidWorks ASSEMBLY AIRPLANE Page 8-1
Chapter 8 Airplane Assembly A. Insert Set of Parts. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click View Menu > Origins to display the origin. Step 3. Click Keep Visible in the Property
More informationCO 2 Shell Car. Body. in the Feature Manager and click Sketch from the context toolbar, Fig. 1. on the Standard Views toolbar.
CO 2 Shell Car Chapter 2 Body A. Save as "BODY". Step 1. If necessary, open your BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in BODY for the filename and press ENTER. B. FRONT Wheel Shell.
More informationBoat. Hull. Step 4. Sketch point directly above the Origin, Fig. 2. Use the inferencing line, the dotted line that appears when you sketch the point.
Chapter 1 Boat Hull A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step 3. Click Point on
More informationBattery Holder. Chapter 9. Boat. A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. SolidWorks 10 BATTERY HOLDER AA BOAT Page 9-1
Chapter 9 Boat Battery Holder A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. AA Step 2. Click Front (plane) in the Feature Manager and click Sketch from the Content toolbar, Fig. 1.
More informationBoat. Battery Holder AA
Chapter 9 Boat Battery Holder AA A. Front Extrude. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch context toolbar, Fig. 1. Step 3. Click
More informationF-1 Car. Blank. in the Feature Manager and click Sketch from the Content toolbar, Fig. 3. Origin. on the Features toolbar.
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. F-1 Car Blank Step 2. Click Part Metric from the list of templates and click OK, Fig. 1. If you are not using SOLIDWORKS templates (you should
More informationCO2 Car Assembly. in the Property Manager to place the part at the origin, Fig. 1. on the Assemblies toolbar. SolidWorks Assembly CO2 CAR Page 8-1
Chapter 8 CO2 Car Assembly A. Insert Axles and Wheels. Step 1. Click File Menu > New, click Assembly Metric and OK. Step 2. Click Keep Visible in the Property Manager, Fig. 1. Step 3. Click Browse in the
More informationSpring Assembly. in the Begin Assembly Property. on the Standard toolbar and click Add-Ins.
Chapter 2 Spring Assembly A. Create New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Cancel Manager. in the Begin Assembly Property B. Enable Toolbox Browser. Step 1. If
More informationH Stab and V Stab. Chapter 6. Glider. A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file.
Chapter 6 Glider H Stab and V Stab A. Open and Save as "H STAB". Step 1. Open your STABILIZER BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in H STAB for the filename and press ENTER. B. Sketch
More informationNose Cone. Chapter 4. Rocket 3D Print. A. Revolve. Step 1. Click File Menu > New, click Part and OK. SOLIDWORKS 16 Nose Cone ROCKET 3D PRINT Page 4-1
Chapter 4 Rocket 3D Print Nose Cone A. Revolve. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the content toolbar, Fig. 1. Step
More informationWheels and Axle. Chapter 7. Simples Machines. A. Save As. Step 1. If necessary, open your Track Assembly 15 file. B. Insert Truck Assembly.
Chapter 7 Simples Machines Wheels and Axle A. Save As. Step 1. If necessary, open your Track Assembly 15 file. Step 2. Click File Menu > Save As. Step 3. Key-in WHEELS AND AXLE ASSEMBLY for the filename
More informationBlank. Chapter 1. CO2 Rail Car. A. New Metric Part. Step 1. Click File Menu > New. B. Body. Step 1. Click Right Plane
Chapter 1 A. New Metric Part. Step 1. Click File Menu > New. CO2 Rail Car Blank Step 2. Click Part Metric from the list and click OK, Fig. 1. If you are not using SolidWorks templates (you should be),
More informationGlider. Clay. Fig. 1 Side face. Step 5. In the Convert Entities Property Manager: click side face, Fig. 3 click OK twice, Fig. 3. Fig. 3.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. Step 2. Click the side face of the Fuselage,
More informationSimple Machines. Body. Step 4. Start at Origin and sketch the 8 lines, Fig. 2. Fig. 1. Origin
Chapter 1 Simple Machines Body A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch on the context toolbar, Fig. 1. Step 3. Click
More informationAssembly Motion Study
Penny Hockey Chapter 10 Assembly Motion Study A. Rename Penny Mate. Step 1. Open your PENNY HOCKEY ASSEMBLY file. Step 2. Expand Mates in the Feature Manager and select the last Mate, Fig. 1. This should
More informationGlider. Wing. Top face click Sketch. on the Standard Views. (S) on the Sketch toolbar.
Chapter 5 Glider Wing 4 Panel Tip A. Open and Save As "WING 4 PANEL". Step 1. Open your WING BLANK file. Step 2. Click File Menu > Save As. Step 3. Key-in WING 4 PANEL for the filename and press ENTER.
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 14 Spinning Top Mastercam X6 for SolidWorks Toolpaths A. Insert Handle in New Assembly. Step 1. Click File Menu > New, click Assembly and OK. Step 2. Click Browse in the Property Manager, Fig.
More informationIntroduction to SolidWorks for Technology. No1: Childs Toy
Introduction to SolidWorks for Technology No1: Childs Toy Table of Contents Table of Contents... 1 Introduction... 2 Part Modelling: Cab... 3 Part Modelling: Base... 6 Part Modelling: Wheel... 12 Assembly:
More informationRocket 1. Fin. in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. (L) on the Sketch toolbar. Fig. 1. Fig. 2
Chapter 2 Rocket 1 Fin A. Sketch. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Right Plane in the Feature Manager and click Sketch from the Content toolbar, Fig. 1. Step 3. Click Line
More informationSOLIDWORKS: Lesson III Patterns & Mirrors. UCF Engineering
SOLIDWORKS: Lesson III Patterns & Mirrors UCF Engineering Solidworks Review Last lesson we discussed several more features that can be added to models in order to increase their complexity. We are now
More informationClay. Chapter 9. Glider. A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file.
Chapter 9 A. Open Assembly File. Step 1. Open your GLIDER ASSEMBLY file. Glider Clay B. New Component Part. Step 1. Click Insert Menu > Component > New Part. C. Sketch. Step 1. Click the side face of the
More informationIntroduction to SolidWorks Basics Materials Tech. Wood
Introduction to SolidWorks Basics Materials Tech. Wood Table of Contents Table of Contents... 1 Book End... 2 Introduction... 2 Learning Intentions... 2 Modelling the Base... 3 Modelling the Front... 10
More informationJSS. Ping Pong Ball. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Sketch toolbar.
Chapter 18 JSS Ping Pong Ball A. Half Circle Sketch. Step 1. Click File Menu > New, click Part Metric and OK. Step 2. Click Front Plane in the Feature Manager and click Sketch on the Context toolbar, Fig.
More informationChanges from SolidWorks 2003 to SolidWorks 2004
Changes from SolidWorks 2003 to SolidWorks 2004 The changes from SolidWorks 2003 to SolidWorks 2004 are primarily cosmetic. Consequently, it is quite easy to use the current edition of Learning SolidWorks
More informationInventor 201. Work Planes, Features & Constraints: Advanced part features and constraints
Work Planes, Features & Constraints: 1. Select the Work Plane feature tool, move the cursor to the rim of the base so that inside and outside edges are highlighted and click once on the bottom rim of the
More informationTerminal. Chapter 16. E-Car. A. Component from Design Library. SOLIDWORKS 17 Terminal E-CAR Page 16-1
Chapter 16 E-Car Terminal A. Component from Design Library. Step 1. Click the Design Library tab in the Task Pane (right side of graphics area), Fig. 1. Step 2. Expand routing and click electrical folder
More informationSOLIDWORKS: Lesson 1 - Basics and Modeling. UCF Engineering
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals UCF Engineering SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment for
More informationAutodesk Inventor - Basics Tutorial Exercise 1
Autodesk Inventor - Basics Tutorial Exercise 1 Launch Inventor Professional 2015 1. Start a New part. Depending on how Inventor was installed, using this icon may get you an Inch or Metric file. To be
More information3D Design with 123D Design
3D Design with 123D Design Introduction: 3D Design involves thinking and creating in 3 dimensions. x, y and z axis Working with 123D Design 123D Design is a 3D design software package from Autodesk. A
More informationLesson 4: Assembly Basics
4 Lesson 4: Assembly Basics Goals of This Lesson Understand how parts and assemblies are related. Create and modify the part Tutor2 and create the Tutor assembly. Tutor1 Tutor2 Tutor assembly Before Beginning
More informationSOLIDWORKS: Lesson 1 - Basics and Modeling. Introduction to Robotics
SOLIDWORKS: Lesson 1 - Basics and Modeling Fundamentals Introduction to Robotics SolidWorks SolidWorks is a 3D solid modeling package which allows users to develop full solid models in a simulated environment
More informationDrawing. Chapter 10. Airplane. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager.
More informationTUTORIAL 2. OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs.
TUTORIAL 2 OBJECTIVE: Use SolidWorks/COSMOS to model and analyze a cattle gate bracket that is subjected to a force of 100,000 lbs. GETTING STARTED: 1. Open the SolidWorks program. 2. Open a new part file.
More informationMastercam X9 for SOLIDWORKS
Chapter 21 CO2 Shell Car Mastercam X9 for SOLIDWORKS A. Enable Mastercam for SOLIDWORKS. Step 1. If necessary, turn on Mastercam for SOLIDWORKS, click the flyout of Options on the Standard toolbar and
More informationSOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users
SOLIDWORKS 2016: A Power Guide for Beginners and Intermediate Users The premium provider of learning products and solutions www.cadartifex.com Table of Contents Dedication... 3 Preface... 15 Part 1. Introducing
More informationBottle Rocket. Drawing. on the Com- on the View Layout
Chapter 6 Bottle Rocket Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing Metric and OK. on the Com- Step 2. Click View Layout mand Manager toolbar. Step 3. Click Model View toolbar.
More informationChapter 2 Parametric Modeling Fundamentals
2-1 Chapter 2 Parametric Modeling Fundamentals Create Simple Extruded Solid Models Understand the Basic Parametric Modeling Procedure Create 2-D Sketches Understand the Shape before Size Approach Use the
More informationChapter 11 Solar Car Drawing
Chapter 11 Solar Car Drawing A. Insert Top and Side Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Browse Step 3. Select your solar car assembly file and click Open. Step 4.
More informationAirplane Drawing. Chapter 10. A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK.
Chapter 10 Airplane Drawing A. Insert Right View. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse Step 4. Select your AIRPLANE
More informationThe Fundamentals of SolidWorks Featuring the VEXplorer robot with over 40 integrated stand-alone tutorials
INSIDE: Tutorial Model Files On CD The Fundamentals of SolidWorks 2007 Featuring the VEXplorer robot with over 40 integrated stand-alone tutorials David C. Planchard & Marie P. Planchard, CSWP SDC PUBLICATIONS
More informationME009 Engineering Graphics and Design CAD 1. 1 Create a new part. Click. New Bar. 2 Click the Tutorial tab. 3 Select the Part icon. 4 Click OK.
PART A Reference: SolidWorks CAD Student Guide 2014 2 Lesson 2: Basic Functionality Active Learning Exercises Creating a Basic Part Use SolidWorks to create the box shown at the right. The step-by-step
More informationSpeedway. Motion Study. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click Tools Menu > Add-Ins.
Chapter 8 Speedway Motion Study A. Enable SolidWorks Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, turn on SolidWorks Motion. To turn on SolidWorks Motion, click
More informationBelt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New
Mastercam 2017 Chapter 35 Belt Buckle A. Create Rectangle. Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click Rectangle.
More informationSOLIDWORKS 2018 Reference Guide
SOLIDWORKS 2018 Reference Guide A comprehensive reference guide with over 250 standalone tutorials David C. Planchard, CSWP, SOLIDWORKS Accredited Educator SDC PUBLICATIONS Better Textbooks. Lower Prices.
More informationParametric Modeling with SolidWorks
Parametric Modeling with SolidWorks 2012 LEGO MINDSTORMS NXT Assembly Project Included Randy H. Shih Paul J. Schilling SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com
More informationSpeedway. Motion Study. on the Standard toolbar and click Add-Ins. at the lower
Chapter 8 Speedway Motion Study A. Enable SOLIDWORKS Motion. Step 1. If necessary, open your Speedway Assembly file. Step 2. If necessary, enable Motion, click the flyout of Options on the Standard toolbar
More informationSOLIDWORKS 2017 Keyboard Modifiers & Shortcuts
SOLIDWORKS 2017 Keyboard Modifiers & Shortcuts Copy/Paste Ctrl+C and Ctrl+V These are similar in functionality to Windows. Sketches Copies and pastes sketch entities. Part Copies and pastes sketches. Assemblies
More informationSolidWorks Intro Part 1b
SolidWorks Intro Part 1b Dave Touretzky and Susan Finger 1. Create a new part We ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select File New Templates IPSpart If the SolidWorks
More informationAutodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies
Autodesk Inventor Design Exercise 2: F1 Team Challenge Car Developed by Tim Varner Synergis Technologies Tim Varner - 2004 The Inventor User Interface Command Panel Lists the commands that are currently
More informationSolidWorks 2½D Parts
SolidWorks 2½D Parts IDeATe Laser Micro Part 1b Dave Touretzky and Susan Finger 1. Create a new part In this lab, you ll create a CAD model of the 2 ½ D key fob below to make on the laser cutter. Select
More informationME 120: Impeller Model in Solidworks 1/6
ME 120: Impeller Model in Solidworks 1/6 Steps to Draw Pump Impeller: The steps below show one way to draw the impeller. You should make sure that your impeller is not larger than the one shown or it may
More informationJewelry Box Lid. A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Fig. 3
Mastercam X9 Chapter 39 Jewelry Box Lid A. Sketch Lid Circle. Step 1. If necessary start a new Mastercam file, click FILE Menu > New. Step 2. Click CREATE Menu > Arc > Circle Center Point. Step 3. Key-in
More informationSOLIDWORKS Parametric Modeling with SDC. Covers material found on the CSWA exam. Randy H. Shih Paul J. Schilling
Parametric Modeling with SOLIDWORKS 2015 Covers material found on the CSWA exam Randy H. Shih Paul J. Schilling SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF
More informationFlow Sim. Chapter 16. Airplane. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 16 Airplane Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar
More informationLesson 12 Bottom-Up Assembly Modeling
Lesson 12 Bottom-Up Assembly Modeling Upon successful completion of this lesson, you will be able to: Create a new assembly. Insert components into an assembly using all available techniques. Add mating
More informationMemo Block. This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet.
Commands Used New Part This lesson includes the commands Sketch, Extruded Boss/Base, Extruded Cut, Shell, Polygon and Fillet. Click File, New on the standard toolbar. Select Part from the New SolidWorks
More informationAirplane Propeller. Click Show All from the Zoom Control at the right end of the Timeline.
Flash Chapter 10 A. Open your "airplane path" file. Step 1. Open your airplane path file. B. Move Propeller Off Fuselage. Airplane Propeller Step 1. Click Edit Symbols Button at the right end of the Timeline,
More informationChapter 4 Feature Design Tree
4-1 Chapter 4 Feature Design Tree Understand Feature Interactions Use the FeatureManager Design Tree Modify and Update Feature Dimensions Perform History-Based Part Modifications Change the Names of Created
More informationSolidWorks 2008 Tutorial. with MultiMedia CD. A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling
INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects with MultiMedia CD A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard
More informationAutodesk Fusion 360 Training: The Future of Making Things Attendee Guide
Autodesk Fusion 360 Training: The Future of Making Things Attendee Guide Abstract After completing this workshop, you will have a basic understanding of editing 3D models using Autodesk Fusion 360 TM to
More informationMastercam X6 for SolidWorks Toolpaths
Chapter 21 CO2 Shell Car Mastercam X6 for SolidWorks Toolpaths A. Enable Mastercam for SolidWorks. Step 1. If necessary, turn on Mastercam for SolidWorks, click Tools Menu > Add-Ins. Step 2. In the dialog
More informationFlow Sim. Chapter 12. F1 Car. A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file.
Chapter 12 F1 Car Flow Sim A. Enable Flow Simulation. Step 1. If necessary, open your ASSEMBLY file. Step 2. If necessary, turn on Flow Simulation, click the flyout of Options on the Standard toolbar and
More informationVisit the following websites to learn more about this book:
Assembly Modeling Model Files Initial and Final Solutions! with SolidWorks 2012 For the SolidWorks user who needs to understand Assembly modeling By Planchard & Planchard CSWP SDC SSoolliiddW Woorrkkss
More informationParametric Modeling with SOLIDWORKS 2017
Parametric Modeling with SOLIDWORKS 2017 NEW Contains a new chapter on 3D printing Covers material found on the CSWA exam Randy H. Shih Paul J. Schilling SDC PUBLICATIONS Better Textbooks. Lower Prices.
More informationSolidWorks 2013 and Engineering Graphics
SolidWorks 2013 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following
More informationSolidWorks 2015 User Interface
SolidWorks 2015 User Interface SolidWorks a Dassault Systèmes Product Starting SolidWorks 1) On the desktop, double-click or from the start menu select: All Programs SOLIDWORKS 2015 SOLIDWORKS 2015. 2)
More informationChapter 39. Mastercam Jewelry Box Tray. A. Sketch Tray Circle. B. Twin Edge Point Circles. Mastercam 2017 Tray Jewelry Box Page 39-1
Mastercam 2017 Chapter 39 A. Sketch Tray Circle. Jewelry Box Tray Step 1. If necessary start a new Mastercam file, click New (Ctrl-N) on the Quick Access Toolbar QAT. Step 2. On the Wireframe tab click
More informationAssembly Modeling with SolidWorks For the Intermediate SolidWorks User. David C. Planchard & Marie P. Planchard SDC PUBLICATIONS
Supplemental Files on CD Assembly Modeling with SolidWorks 2006 For the Intermediate SolidWorks User David C. Planchard & Marie P. Planchard SDC PUBLICATIONS Schroff Development Corporation www.schroff.com
More informationAssembly Modeling Constraints. ENGR 1182 SolidWorks 05
Assembly Modeling Constraints ENGR 1182 SolidWorks 05 Today s Objectives Creating assemblies by constraining 3D parts together Movement and Location dictated by Constraints SW05 Activity SW05 Application
More informationDelta IV Heavy. Interstage. in the Feature Manager and click Sketch on the Context toolbar, Fig. 1. on the Command Man- on the Features
Chapter 4 Delta IV Heavy Interstage A. Sketch Circles. Step 1. Click File Menu > New, click Part and OK. Step 2. Click Top Plane in the Feature Manager and click Sketch on the Context toolbar, Fig. 1.
More informationChapter 1. SolidWorks Overview
Chapter 1 SolidWorks Overview Objectives: When you complete this chapter you will: Have a good background knowledge of SolidWorks Have learnt how to start a SolidWorks session Understand the SolidWorks
More informationSOLIDWORKS 2016 and Engineering Graphics
SOLIDWORKS 2016 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
More informationPhotoView 360 Decals
Chapter 10 Glider PhotoView 360 Decals A. Enable PhotoView 360. Step 1. If necessary, open your GLIDER ASSEMBLY file. Step 2. If necessary, turn on PhotoView 360. Click Tools Menu > Add- Ins. Click to
More informationDrawing. Chapter 12. Beam. A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View. on the View Layout toolbar.
Chapter 12 Beam Drawing A. Insert Views. Step 1. Click File Menu > New, click Drawing and OK. Step 2. Click Model View on the View Layout toolbar. Step 3. Click Browse in the Property Manager. Step 4.
More informationLearning. Modeling, Assembly and Analysis SOLIDWORKS Randy H. Shih SDC. Better Textbooks. Lower Prices.
Learning SOLIDWORKS 2016 Modeling, Assembly and Analysis Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites
More informationFlow Sim. Chapter 14 P-51. A. Set Up. B. Create Flow Simulation Project. Step 1. Click Flow Simulation. SolidWorks 10 Flow Sim P-51 Page 14-1
Chapter 14 A. Set Up. P-51 Flow Sim Step 1. If necessary, open your ASSEMBLY file. Step 2. Click Tools Menu > Add-Ins. Step 3. In the dialog box, scroll down to Flow Simulation and place a check in the
More informationThis is the opening view of blender.
This is the opening view of blender. Note that interacting with Blender is a little different from other programs that you may be used to. For example, left clicking won t select objects on the scene,
More informationCHAPTER 1: SOLIDWORKS 2008 USER INTERFACE
CHAPTER 1: SOLIDWORKS 2008 USER INTERFACE Chapter Objective SolidWorks is a design software application used to model and create 2D and 3D sketches, 3D parts and assemblies, and 2D drawings. Chapter 1
More informationSolidworks 2006 Surface-modeling
Solidworks 2006 Surface-modeling (Tutorial 2-Mouse) Surface-modeling Solid-modeling A- 1 Assembly Design Design with a Master Model Surface-modeling Tutorial 2A Import 2D outline drawing into Solidworks2006
More informationAirplane. Chapter 21. Mastercam A. Create Rectangle. B. Save As AIRPLANE. C. Set Grid and Snap.2. Mastercam 2017 Airplane Page 21-1
Mastercam 2017 Chapter 21 A. Create Rectangle. Airplane Step 1. If necessary start a new Mastercam file, click New on the Quick Access Toolbar QAT (Ctrl-N). Step 2. On the Wireframe tab click Rectangle.
More informationStructural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment
ANSYS Workbench Tutorial Structural & Thermal Analysis Using the ANSYS Workbench Release 12.1 Environment Kent L. Lawrence Mechanical and Aerospace Engineering University of Texas at Arlington SDC PUBLICATIONS
More information