SW: /Encryption HW: THR-4 Nokia THR 850 SW:

Transcription

1

2 Information about the equipment used for testing Testing during the January 2003 IOP Test Session: The tests were performed using the following terminals: Manufacturer Terminal Type Software/Hardware Release No. SW/ HW: R SW/ HW: R SW/ HW: R SW: /Encryption HW: THR-4 SW: VECTOR PRM 5202A 4006 PHOBE TECOM 21 CM MDT400 HW: THR-3 SW: AlgPkgTea2, RedDSP, TSM: ControlTarget, BlackDSP: TAA: Unknown HW: Issue 1 SW: TS 0031 A - TM 0023 A HW: V.3 SW: 010F HW: LAPOUT 3 SW: 0.36G4C HW: 1.5 SW: HW: has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 2 of 17

3 Additional information about the test performed The tests were performed in the MHz band. The SwMI was operating with the following configuration: MCC 346 MNC 5 Colour code LA1 carrier frequency (BS Tx) MHz LA2 carrier frequency (BS Tx) MHz PSTN gateway (FFFFE0) Subscriber classes FFFF 16 Test Results The test results are shown in the tables below. Test results and the certificates from previous IOP test session are available on TETRA MoU web site ( Tables indicate whether or not tests addressing a specific requirement of the TIP specification have been performed, whether or not the requirement is applicable for the SwMI, and the result of the test if executed. Each entry of the table may take one of seven values: - : No test performed. N/A: Not applicable for the SwMI NTPA: No Test Plan/case Available No : Not supported by Terminal P : Pass F : Fail I : Inconclusive No test performed (-) is assigned in case of no test case performed during the IOP session. The test results have been derived from examining the behaviour of a live system. The verdicts indicated are based on the log evaluation of the information exchange between the SwMI and the terminals indicated in the following tables. The verdicts reflect the fact that at the time of the IOP testing it was/was not possible to demonstrate a behaviour that was in accordance with the related requirement. has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 3 of 17

4 Table 1. CORE TTR Registration 6.1 ITSI attach - ITSI attach (without group attachment) No No No P P P P P ITSI attach including group attachment 1.2 P No No P P P 6.2 ITSI attach including group attachment Ms P P No initiated Multiple group attachment during MS registration Roaming&perioding location updating Cell reselection P P P P I1 without communication activity SwMI initiated location updating SwMI initiated location updating without group reporting P P P P P 6.4 SwMI initiated location updating SwMI initiated N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A location updating with group reporting De-registration 1.4 P P P P P P 7 Individual call 7.1 Call set-up Hook signalling Individual hook call set-up P P P Hook signalling Individual call set-up, resource P P P queuing Hook signalling Duplex call set-up P P P P No F Hook signalling Duplex call set-up, resource P P P P No queuing Hook signalling. MS-ISDN Individual call 9.1 P P P P F1 P P Direct through-connect MS-ISDN Individual call Direct through-connect Individual direct call set-up P P P P P F Direct through-connect Individual call set-up P P P resource queuing Call set-up Modifications Point to point to point to multipoint Emergency 4 call set-up, P2P to P2MP call modification No No No P P P F Duplex to simplex Call set-up modifications by No 3 called party, duplex to semiduplex No No P P P P Direct to hook Call set-up Modification by called 1 party, direct to hook P P P P F1 7.2 Transmission control End of transmission Individual hook call set-up P P P End of transmission Individual direct call set-up P P P P P F Request to transmit Individual hook call set-up P P P Request to transmit MS-ISDN Individual call 9.1 P P P P P F Request to transmit Individual direct call set-up Request to transmit ( in the presence of an active talker) pre-emptive speech item request, non pre emptive transmission request queuing has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Page 4 of 17

5 7.2.3 Request to transmit ( in the presence of an N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A active talker) pre-emptive speech item request, non pre emptive transmission request rejection Call Maintenance Queuing during Individual call P P restoration, Transmitting Call Maintenance Queuing during individual call P restoration, receiving. (Announced Type 3) Call Maintenance Queuing during individual call P No No No restoration. Receiving (Unannounced) Call Maintenance Queuing during individual call P restoration. Communication inactivity. (Announced Type 3) Call Maintenance Queuing during Individual call P No No No restoration, Communication inactivity (Unannounced) Call Maintenance Queuing during Duplex call P P P P restoration (Announced type 3) Call disconnection Individual hook call set-up P P P Call disconnection Individual direct call set-up P P P P P F Call disconnection Duplex call set-up P P P P No F1 7.5 Emergency individual call. Emergency individual No No No P P P F1 call. Resource pre-emption Emergency speech item request Emergency individual call. Resource pre-emption No No No P P P F Emergency individual call modification No No No P P P F2 Emergency call set-up, P2P to P2MP call modification Group management Class of usage values 101 2, 011 2, 010 2, High, normal, low priority scanned. Status to scanned group P P No P Selected group and SwMI initiated P P P attachment/detachments Roaming outside and back inside of group area of the selected group Selected group and SwMI initiated P P No attachment/detachments Roaming outside and back inside of group area of an attached nonselected group Attachment of the selected group MS initiated No No No P P P F8 P single group attachment of the selected group, accepted (by an MS, which can have no selected group) 8.4 Attachment of the selected group MS initiated No No No P P P F8 P single group attachment of the selected group, rejection (by an MS, which can have no selected group) 8.4 Attachment of the selected group Null group P P P No F8 P attachment as the selected group Attachment of the selected group Change of selected group P P P P F9 P has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 5 of 17

6 8.5 Multiple group attachment MS initiated single P P No F8 P group attachment of other than selected group, accepted Multiple group attachment MS initiated single P P No F8 P attachment of other than selected group, rejection Multiple group attachment MS initiated Multiple No P No group attachment, rejection of some of the attached groups Multiple group attachment MS initiated Multiple No P No group attachment with attachment to selected group Multiple group attachment MS initiated Multiple P P No F7 group attachment during MS registration Multiple group attachment Ms initiated Multiple group attachment with no selected group No P No 8.5 Multiple group attachment MS initiated Multiple N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A group attachment, only the attachment of the selected group is accepted MS initiated detachment MS initiated detachment No No No - P P of the selected group MS initiated detachment MS initiated group No No No I5 P No detachment of the selected group and an attached group SwMI initiated group attachment and detachment SwMI initiated detachment SwMI initiated group N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A detachment with another value than Temporary 1 detachment and attachment SwMI initiated detachment Roaming outside and P P P back inside of group area of the selected group SwMI initiated detachment Roaming outside and P P No back inside of group area of an attached non/selected group SwMI initiated attachment SwMI initiated group N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A detachment with another value than Temporary 1 detachment and attachment SwMI initiated attachment Roaming outside and P P No back inside of group area of an attached non/selected group SwMI initiated attachment Roaming outside and back inside of group area of the selected group P P P SwMI initiated location updating with group N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A report request SwMI initiated location updating with group reporting SwMI initiated registration without group report P P P P P request SwMI initiated location updating without group reporting Group call 9.1 Call set-up Normal Group call 3.1 P P P P P 9.1 Call set-up Group Call set-up, resource queuing 3.3 P P P P P P has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 6 of 17

7 9.1 Call set-up MS-ISDN group call 9.2 P P P 9.1 Call set-up Group scanning 3.8 No No No P P No F10 P Call set-up modifications Group call-swmi N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A changes requested call priority End of transmission Normal Group call 3.1 P P P P P End of transmission Group scanning 3.8 No No No P P No F10 P Request to transmit Normal Group call 3.1 P P P P P Request to transmit MS-ISDN group call 9.2 P P P Request to transmit Pre-emptive speech item N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A request, non pre-emptive transmission request queuing Request to transmit Group scanning 3.8 No No No P P No F10 P Request to transmit Pre-emptive speech item N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A request, non pre-emptive transmission request rejection Call disconnection Normal Group call 3.1 P P P P P 9.3 Call disconnection Group call disconnection by call N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A owner MS Late entry 3.2 P P P P F11 P 9.6 Emergency group call 9.6 Emergency group call Emergency call set-up to busy group, speech item interruption P P P P F4 9.6 Emergency group call Pre-emption during group N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A call restoration. Transmitting (Announced Type 3) Emergency group call Emergency group call P P P P F2 resource pre-emption Emergency speech item request Emergency call P P P P F4 set-up to busy group speech item interruption Emergency group call modification Emergency No No No P P P F1 call set-up, P2MP to P2P call modification Cell re-selection 10.1 Undeclared cell re-selection Cell re-selection without communication activity P P P P I Unannounced cell re-selection with call restoration Unannounced cell re-selection Group call P P restoration, Receiving (Unannounced) Unannounced cell re-selection Queuing during group call restoration,. Receiving (Unannounced) Unannounced cell re-selection Queuing during individual call restoration. Receiving (Unannounced) Unannounced cell re-selection Queuing during individual call restoration, Communication inactivity (Unannounced) Unannounced cell re-selection individual call restoration, Receiving (Unannounced) P P P No No No P No No No P No No No has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 7 of 17

8 Unannounced cell re-selection individual call P No No No restoration, Communication inactivity (Unannounced) Announced cell re-selection Type without P Preferred Neighbour Selected Group call restoration, Transmitting. (Announced Type 3) Announced cell re-selection without Preferred Neighbour Selected Queuing, during group call restoration, Transmitting (Announced Type 3) P P Announced cell re-selection Type without N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A Preferred Neighbour Selected Pre-emption during group call restoration. Transmitting. (Announced Type 3) Announced cell re-selection Type without P P Preferred Neighbour Selected Individual call restoration. Transmitting party Announced cell re-selection Type without No No No P Preferred Neighbour Selected Individual call restoration. Receiving (Announced Type 3) Announced cell re-selection Type without No No No P Preferred Neighbour Selected Queuing during individual call restoration. Communication inactivity. (Announced Type 3) Announced cell re-selection Type without P P Preferred Neighbour Selected Queuing during individual call restoration. Transmitting Announced cell re-selection Type without No No No P Preferred Neighbour Selected Queuing during individual call restoration. Receiving (Announced Type 3) Announced cell re-selection Type without No No No P Preferred Neighbour Selected individual call restoration. Communication inactivity (Announced Type 3) Announced cell re-selection Queuing during P P P P Duplex call restoration (Announced Type 3) Announced cell re-selection Duplex call P P P P restoration (Announced Type 3) Announced cell re-selection Type with Preferred No No No No No No Neighbour Selected Group call announced cellreselection with preferred neighbour selected and with call restoration, Transmitting Announced cell re-selection Type with Preferred No No No No No No Neighbour Individual call, Announced cell rereselection with preferred neighbour selected and with call restoration Transmitting Announced Type with Preferred Neighbour No No No No No No Selected and without Forward Registration Group call Announced cell re-selection without call restoration, (seamless hand-over) without forward registration transmetting has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 8 of 17

9 Announced Type with Preferred Neighbour Selected and without Forward Registration Duplex call, Announced cell-re-selection without call restoration without forward registration Announced Type with Preferred Neighbour Selected and with Forward Registration Individual call. Announced cell re-selection without call restoration with forward registration. Transmitting Preferred Neighbour Selected and without Forward Registration Forward Registration Group call. Announced cell re-selection without call restoration with forward registration. Transmitting Short data service Service Overview MS-ISDN addressed individual status message Service Overview MS-ISDN addressed group status message 9.4 MS to Wireline Dispatcher with Status Acknowledge Status transfer to dispatcher MS to MS/Group with General Status Acknowledge) Status transfer to group MS to MS/Group with General Status Acknowledge Individual addressed status transfer (Dispatcher) MS to MS/Group with General Status Acknowledge Status to scanned group MS to MS/Group with General Status Acknowledge MS-ISDN addressed group status message 9.4 MS to MS/Group with General Status Acknowledge MS-ISDN addressed individual status message Telephone call 12.2 Call Set-up 12.1 Gateway addresses TETRA-originated call set-up 8.1 No No No No No No No No No No No No No No No No P P No P P P P P P P P P P P P P P P P P P P P P P P1 P P No P P14 P14 P P No P P F1 P MS Originated, Late Through-Connect TETRAoriginated P P F1 P call set-up MS Originated, early Through-Connect TETRAoriginated call set-up MS Originated, Call Queued TETRA-originated call P P F1 P set-up queuing MS terminated PSTN originated call 8.3 P P F1 P 12.4 DTMF Over dial TETRA-originated successful DTMF over-dial 8.4 P P F3 P 12.4 DTMF Over dial TETRA-originated unsuccessful N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A DTMF over-dial Disconnect Causes TETRA-originated call set-up 8.1 P P F1 P has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 9 of 17

10 12.5 Disconnect Causes TETRA-originated call set-up P P F1 P queuing Disconnect Cause PSTN originated call 8.3 P P F1 P 12.6 Emergency telephone call Emergency call to No No No P P P P emergency number Layer 2 operation Up-link FACCH and down-link TCH. Sending F5 P P P 4 SDS-TL message in FACCH during group call Traffic channel (TCH). Sending SDS-TL message P P P P 2 in SACCH during group call Traffic channel (TCH). Sending SDS-TL message P P P P P P 2 in SACCH during individual call Up-link FACCH and down-link TCH. Sending P P P 4 SDS-TL message in FACCH during individual call 10.3 Table 2. SDS TTR MS-ISDN (SDS-TTR ver.1.0.1) 6.1 Addressing MS-ISDN addressed individual SDS-TL P P message Addressing MS-ISDN addressed group SDS-TL P message User defined data Type 1, 2 and 3 7 User defined data Type 1, 2 and 3 Individual P P addressed SDS Type 1 transfer User defined data Type 1, 2 and 3 Individual No No P P addressed SDS Type 2 transfer User defined data Type 1, 2 and 3 Individual No No P P addressed SDS Type 3 transfer User defined data Type User defined data Type 4 SDSL-TL message to P scanned group MS to MS, Standard Report Individual addressed P text messaging SDS-TL, (with acknowledgement) MS to MS, Standard Report group addressed text P messaging SDS-TL, (without acknowledgement) MS to MS, Standard report. MS-ISDN addressed P P individual SDS-TL message MS to MS, Standard report. MS-ISDN addressed P14 group SDS-TL message MS to MS, Standard report. Sending SDS-TL F5 P P P message in FACCH during group call MS to MS, Standard report. Sending SDS-TL P P P P P P message in SACCH during group call MS to MS, Standard report. Sending SDS-TL P P P P P P message in SACCH during individual call MS to MS, Standard report. Sending SDS-TL P P P message in FACCH during individual call MS to MS, Short Report individual addressed text P messaging SDS-TL, (with acknowledgement) has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 10 of 17

11 8.1.3 MS to MS, Short Report group addressed text P messaging SDS-TL, (without acknowledgement) MS to MS, Short report Sending SDS-TL message P P P in FACCH during individual call MS to MS, Short report Sending SDS-TL message P P P P P P in SACCH during individual call MS to MS, Short report. MS-ISDN addressed P P individual SDS-TL message Text messaging Text Length. MS-ISDN addressed individual SDS- P P TL message Text Length. MS-ISDN addressed group SDS-TL message Data Coding Scheme. MS-ISDN addressed group SDS-TL message 9.6 P Data Coding Scheme. MS-ISDN addressed P P individual SDS-TL message PDU Contents. Sending SDS-TL message in F5 P P P FACCH during group call PDU Contents. Sending SDS-TL message in P P P P P P SACCH during group call PDU Contents. MS-ISDN addressed individual P P SDS-TL message PDU Contents.MS-ISDN addressed group SDS-TL message 9.6 P PDU contents Report group addressed text P messaging SDS-TL, (without acknowledgement) PDU contents SDSL-TL message to scanned group P (without acknowledgement) Table 3. DGNA TTR SS-DGNA not supported 7.5 SS-DGNA specific functions not supported SS- DGNA specific function not supported by MS SS-DGNA specific functions not supported SS- N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A DGNA specific function not supported by SwMI Supported SS-DGNA functions 8.1 Group assignment 8.1 Group assignment DGNA assignment without N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A attachment Group assignment DGNA assign with attachment N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A as selected group, MS has no selected group Group assignment DGNA assign with attachment N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A as selected group, MS has selected group Group assignment DGNA assign with attachment, F16 attachment not allowed at next ITSI attach Group assignment DGNA assign with attachment, P attachment required at next ITSI attach Group assignment DGNA assign with attachment, pre programmed group has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 11 of 17

12 8.1 Group assignment DGNA assign with attachment as scanned group, MS has selected group Group assignment DGNA assign, with embedded attachment rejected attachment by MS Assignment of a group without attachment N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A DGNA assignment without attachment Assignment of a group with attachment DGNA N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A assign with attachment as selected group, MS has no selected group Assignment of a group with attachment DGN/A assign with attachment as scanned group, MS has selected group Assignment of a group with attachment DGNA N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A assign with attachment as selected group, MS has selected group Assignment of a group with attachment DGNA F16 assign with attachment, attachment not allowed at next ITSI attach Assignment of a group with attachment DGNA P assign with attachment, attachment required at next ITSI attach Assignment of a group with attachment DGNA assign, with embedded attachment rejected by MS Group de assignment 8.2 Group de assignment Removing radio P subscriber from selected DGNA group Group de assignment De-assignment of MS from P pre-programmed selected group Group de assignment De-assignment of MS from pre-programmed scanned group Table 4. AUTHENTICATION TTR Authentication functions SwMI initiated authentication 7.1 General Successful ITSI attach with authentication P P P General Rejected registration, authentication failure I1 P P P General Successful roaming location update with P P P authentication Table 5. PACKET DATA TTR Packet Data functions 7.1 Context Activation (Test case Number index) TE IPCP Initiated, Static Address (TE supplied) Packet Data Context Activation, static IP address TE IPCP Initiated, Dynamic Address Packet Data Context Activation, dynamic IP address User Authentication using PAP Packet Data context Activation, with PAP user authentication P has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 12 of 17

13 7.1.3 User Authentication using PAP Packet Data context Activation, APN index selected User Authentication using CHAP Packet Data P context Activation, with CHAP user authentication Failed user authentication Packet Data context P6 activation rejected, PAP user authentication Failed user authentication Packet Data context P6 activation rejected, CHAP user authentication Provisioning Reject Packet Data context activation, activation rejected Provisioning Reject Packet Data context Activation P rejected, invalid APN index selected Provisioning Reject Packet Data context activation P6 rejected, PAP user authentication Provisioning Reject Packet Data context Activation P6 rejected, CHAP user authentication Context Deactivation MS initiated deactivation Packet Data context P deactivation, MS initiated, AL established MS initiated deactivation Packet Data context deactivation, MS initiated, AL not established Explicit on SwMI PDCH access Data transmission, SwMI initiated PDCH access, MS reject SwMI initiated deactivation Packet Data context deactivation, SwMI initiated, AL not established SwMI initiated deactivation Packet Data context deactivation, SwMI initiated, AL established PDCH Access MS Initiated access on the MCCH Data transmission MS Initiated PDCH access, AL not established, no ALQoS negotiation MS Initiated access on the MCCH Data transmission MS Initiated PDCH access, AL established MS Initiated access on the MCCH Data transmission, MS Initiated PDCH access, AL not established, AL QoS re-negotiation SwMI initiated access on the MCCH Data transmission, SwMI initiated PDCH access, AL not established MS Initiated Access Reject Data transmission, MS initiated PDCH access, SwMI reject SN Data transfer 7.4 SN-DATA transfer Data transmission MS Initiated PDCH access, AL not established, no ALQoS renegotiation SN-DATA transfer PDCH Access, Data transmission, MS initiated PDCH access, AL not established, AL QoS re-negotiation has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 13 of 17

14 7.4 SN-DATA transfer Data transmission MS Initiated PDCH access, AL established SN-DATA transfer Data transmission, SwMI initiated PDCH access, AL established SN-DATA transfer Data transmission, SwMI initiated PDCH access, AL not established End of Data Normal Data transmission MS Initiated PDCH access, AL not established, no ALQoS renegotiation Normal Data transmission MS Initiated PDCH access, AL not established, ALQoS re-negotiation Normal Data transmission, MS Initiated PDCH access, AL established Data transmission SwMI Initiated PDCH access, AL not established Normal Data transmission, SwMI initiated PDCH access, AL established Normal Roaming during data transmission Normal Roaming without data transmission at MS side, READY state Normal Roaming without data transmission, STANDBY state Advanced Link Set-up MS Initiated AL Set-up Data transmission MS Initiated PDCH access, AL not established, ALQoS re-negotiation MS initiated AL Set-up PDCH Access, SwMI Initiated PDCH access, AL not established MS initiated AL Set-up Data transmission, MS initiated PDCH access, AL not established, no AL QoS re-negotiation MS Initiated AL Reset Roaming during data transmission Advanced Link Data Transfer Normal Down-link Data transmission, SwMI initiated PDCH access, AL not established Normal Down-link Data transmission, SwMI initiated PDCH access, AL established Normal Up-link Data transmission MS Initiated PDCH access, AL not established, no ALQoS renegotiation Normal Up-link Data transmission MS Initiated PDCH access, AL established Normal Up-link Data transmission MS Initiated PDCH access, AL not established, ALQoS renegotiation Normal Up-link Roaming without data transmission, STANDBY state has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 14 of 17

15 7.8 Advanced Link Disconnection MS initiated Context Deactivation Packet Data P context deactivation, MS initiated, AL established SwMI initiated Context Deactivation Packet Data context deactivation, SwMI initiated, AL established Link Reconnect BS Data Roaming without data transmission at MS side, READY state MS Data Roaming during data transmission Table 7. FSSN TTR Individual call using FSSN Individual intra FSSN call within a fleet Individual call using FSSN Individual intra FSSN call between two fleet Group call within single FSSN domain using FSSN for CPI/TPI Group call within single FSSN domain Group call maintenance using FSSN for TPI Group call within single FSSN domain Individually and group addressed status messages Individually addressed FSSN status messages Individually and group addressed status messages FSSN as a CPI in group addressed status message Individually and group addressed SDS text status messages Individually addressed FSSN SDS-TL messages Individually and group addressed SDS text status messages Group addressed FSSN SDS-TL messages Table 8. AMBIENCE Listening SS-AL Call set-up Ambience listening call set-up SwMI initiated disconnection of SS-AL call Ambience listening call set-up Affected user MS receives a new call request from the SwMI during SS-AL call Ms makes a new individual call during Ambience Listening call PDP context activation during SS-AL call MS activates PDP context during Ambience Listening call MS attempts to start a packet data instance during SS-AL call MS starts Packet Data transfer during Ambience Listening call MS attempts to start a packet data instance during SS-AL call Ambience Listening Call set-up to MS that has an active PDP context P P P P P P P P P P P P P P P P P P No P P No P P No P P No P P No P P No P has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 15 of 17

16 SS-AL call set-up to MS that has an active PDP context Ambience Listening Call set-up to MS that has an active PDP context Table 9. E2EE with Clear Voice Override No P Call set-up E2E encrypted Individual call P Call set-up E2E encrypted group call P Call set-up E2E encrypted group call with CVO, P incorrect encryption key Transmit request E2E encrypted group call P Transmit request E2E encrypted Individual call - P Transmit request E2E encrypted group call with P CVO, incorrect encryption key Unacceptable encryption mode in call set-up P Rejection of E2E encrypted Individual call Unacceptable encryption mode in call set-up P Rejection of individual clear voice call, MS require encryption Call set-up(core) E2E encrypted group call, late entry P Announced cell re-selection Type without P Preferred Neighbour Selected(Core) Individual E2E encrypted call restoration. Transmitting party (Announced type 3) has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 16 of 17

17 Comments: NIROS I1 MS can only to roam from LA1 > LA2, but not back from LA2 > LA1. F1 MS does not acknowledge presence check D-INFO PDUs, thus SwMI releases the individual call. F2 MS does not receive audio when dispatcher is transmitting F3 MS sends incorrect DTMF procedure F4 MS uses wrong priority in U-TX DEMAND. "Pre-emptive priority 4" is used in U-SETUP but in U-TX DEMAND used priority is " Pre-emptive priority" which is not supported by SwMI and pre-emption fails. P1 Optional step not performed. MOTOROLA F5 MS (MTM 700) sends only 2 fragments out of 3 while MS B is transmitting. All 3 fragments are sent successfully after MS B released PTT. I1 MS MTM 700 does not acknowledge U-LOCATION UPDATE REJECT PDU and remains transmitting U-LOCATION UPDATE DEMAND PDUs. NOKIA I5 MS (THR ) attaches group as not scanned (CoU 2), instead detaching P14 SwMI does not convert SSI to MS-ISDN for Calling MS Identity when sending group addressed status message and SDS-TL message. F16 SwMI rejects MS selected group attachment (CoU5) after powering on and re-attach the group with CoU 4. P6 The content definition in the D-SN-ACTIVATE PDP CONTEXT REJECT PDU is "any reason" instead of "User authentication failed". F8 Detewe MS tries to attach also GSSI 0 with CoU 2 (not scanned) embedded to attachment in question. Attachment of GSSI 0 is rejected by SwMI F9 MS Selected group is not changed. Instead selected group (CoU 5) is changed to High (CoU 6) F7 MS attaches selected group (CoU 5) and three (3) Not scanned (CoU 2) groups embedded to U- LOCATION UPDATE DEMAND PDU. No subsequent group attachment signalling. F10 MS receives the transmission to Group B even Group B was attached with CoU 2 (not scanned) F11 MS craches when powered on during active group call. has made every effort to ensure that tests have been made correctly, and in accordance with the relevant TIPs. has no liability for the test results, or towards the manufacturers. Page 17 of 17