LinSelect Release Notes

Transcription

1 LinSelect Release Notes

2 Release Notes LinSelect 2 Version Available since: 2016/11/28 Version Available since: 2016/11/29 - Hotfix 1: Bug-fix in update process - Patch 1: Note function in recalculate mode Version Available since: 2016/12/02 - Hotfix 2: Continuous optimization in the calculation algorithm o Torque around the Y-Axis - Service Pack 1: o Extension of the product database o Detail Printout Mouse focus now on printout (previously for language switching) o Result If no result is found, the "Apply product selection" command button is grayed out Default-Designation of project and systems now --- The project name is displayed above the project table. By doubleclicking the project name can be changed. System name in the table can be changed by double-clicking the corresponding line Recalculate Jump into the step Process.The system, which is recalculated, is now displayed in the status bar o Recalculate Product It is possible to change the power supply voltage of the drive controller Lifetime It is possible to change hours and days Version Available since: 2016/12/06 - Hotfix 3: Continuous optimization in the calculation algorithm o Lifetime

3 Release Notes LinSelect 3 Version Available since: 2016/12/22 - Hotfix 4: Continuous optimization in the calculation algorithm o Fz - Service Pack 2: o Complementation of the product database Actuators New product variants s_min at Actuators s_min at Linear axes o Global Working area detection and automatic positioning of the application LinSelect (Depending on display 1, display 2, display n, etc.) o Main-Frame Increase and decrease the font size now with control buttons Message box for possible short-stroke applications with explanation Explanation in the message box of the limitation of the effective stroke in the following assembly case: linear axis, vertical, carriage fixed / main body in motion o Detail print Actuator Print "Max. Travel distance" instead of "Length main body" Information about "Selected Linear System" on separate page Printout with the mass of the linear system (with attached motor) Linear axis, carriage fixed/ main body in motion print error in the cyclus chart removed

4 Release Notes LinSelect 4 Version Available since: 2017/02/08 - Hotfix 5: Continuous optimization in the calculation algorithm o Motor cooling - Service Pack 3: o Complementation of the product database New values for the length-dependent spindle inertia New values for allowable loading o General If you get no result, you can save all entered data to your application in your project. If you get no result, you can send all entered data to your application to your Bosch Rexroth contact person directly by . New Indrafunc.dll / Sizebase.db3 integrated for the calculation of motor and drive controllers Optimization in the calculation algorithm for permissible loading Textual description "Compressive force Fz" is replaced by "Force Fz", or at pressure Force Fz - / at pull Force F + Textual description "Lateral force Fy" is replaced by "Force Fy" Textual description "Axial force Fx" is replaced by "Force Fx"tzt Marking by mouse click of the single phases/ profiles now also possible in the graphical chart Display of the velocity/ time coordinates via Mouse -ToolTip in the graphical chart Display of the travel distance/ time coordinates via Mouse -ToolTip in the graphical chart Display of the acceleration/ time coordinates via Mouse -ToolTip in the graphical chart Display of the force Fx / time coordinates via Mouse -ToolTip in the graphical chart Select the desired coordinates from the right mouse context menu in the graphical chart Displays the location and name of the currently open or saved *.LinSelect file Indicates whether the project has already been saved / not saved o Detail print Chart for "Process steps / Cycle (graphical)" and Chart for "Motor and Drive Controller - Result" are now displayed in better resolution. Time stamp additionally for printout and project file. o Result Ranking belt modules within the size at max. Travel distance > 800 [mm] now version MA before MG Default setting for display mode Result table to "All"

5 Release Notes LinSelect 5 Version Available since: 2017/02/09 - Hotfix 6: Process window o Correction of the arrow representation between process step editing and process steps / cycle Version Available since: 2017/03/15 - Hotfix 7: Continuous optimization in the calculation algorithm o Motor and drive calculation Version Available since: 2017/04/05 - Hotfix 8: Continuous optimization in the calculation algorithm o Calculation of the working points and effective torque of the 2nd / 3rd / nth systems for display in the detail chart - Service Pack 4: o Complementation of the product database Further products in the familiy PSK (Optimization variant gen.) Clearly defined s_min values for actuators Clearly defined s_min values for linear axes o General Country specific settings / services possible New languages included Spanish French Italian New Indrafunc.dll / Sizebase.db3 integrated for the calculation of motor and drive controllers Social media to follow and share Interface to the online configurator optimized Rules optimized New profile type Press-in for actuators (simplified) Fast move and slow move. Press-in during slow move with linear force increase. Easy saving and loading of the user data directly at the input field Keeping the user datas during / after update o Detail print Chart for "Process steps / Cycle (graphical)" and Chart for "Motor and Drive Controller - Result" are displayed in the correct page width

6 Release Notes LinSelect 6 Version Available since: 2017/05/17 - Hotfix 9: Continuous optimization in the calculation algorithm o Correction in the rules for the proposal of 2-rail systems at the moment consideration of Mx o Correction calculation for rms speed o Correction in profile "press-in" - Service Pack 5: o General New languages included Chinese Korean Russian New Indrafunc.dll / Sizebase.db3 integrated for the calculation of motor and drive controllers o Prozess Marking & copying multiple related profiles is possible o Ergebnis The "mechanics result", which was only visible in the detailed view in previous versions, is now available in the results table Comparing product variants is possible Copying an axis in the project view is possible o Detail print Scroll through the mouse wheel in the print preview of the detailed view Version Available since: 2017/06/28 - Service Pack 6: o General New Indrafunc.dll / Sizebase.db3 integrated for the calculation of motor and drive controllers Prior a 2-rail system at a center of gravity (Y + / Y- and Z + / Z-), or a force position (Y + / Y- and Z + / Z-) of more than 100 [mm] o Result Ranking actuators improved Ranking linear axes improved Recommended drive controller now designed to meet requirements. Now more motor-controller-combinations are calculated

7 Release Notes LinSelect 7 Version Available since: 2017/08/09 - Hotfix 10: Continuous optimization in the calculation algorithm o Rules "Preference 2-rail systems" from a certain lever arm was completely removed o Correction note for supply voltage - Service Pack 7: o General New Indrafunc.dll / Sizebase.db3 integrated for the calculation of motor and drive controllers Live update (quantity of product variants) to all filters Quantity of possible product combinations now more concisely represented in the status bar Country-specific mail addresses for requests CH, AT, UK, US, SE, IT New rules for the proposal of systems with a certain number of rails and carriages depending on the selected stiffness and the occurring moment load o Construction (linear axes) New filters, texts and graphics for the installation space Main body width (observe contours) Table part height (observe contours) New filters, texts and graphics for mounting work piece Mounting surface "fixed", "variable" Fastening "T-slot", "Thread" with mounting aid "centering bore", "pigtail" New texts for mounting linear axis Help text for acceleration higher than 10 m/s² o System Surface reordered Installation, environmental and operating conditions are combined under the terms of the operating conditions Terms and texts revised Conditions adapted New filters and texts introduced for lubrication LSS, LPG, LCF, LCO Optimized "Precision Accuracy / Stiffness" filter and adapted texts o Search Surface completely new and more clearly structured o Result Ranking linear axes improved Only motor/ controller combinations, which can also be offered in the sales tool When loading older LinSelect projects, LinSelect will check for discontinued product variants and highlight them in color

8 Release Notes LinSelect 8 Version Available since: 2017/08/10 - Hotfix 11: Bugfixing o Default parameters from the section "Mounting Workpiece" will be set if you create a new linear system o Overwrite an existing system in the project table by logging on with "Extended authorizations" is now prevented Version Available since: 2017/08/29 - Hotfix 12: Continuous optimization in the calculation algorithm / Bugfixing o Calculation torque My o Limits torque Mx, My, Mz updated o Extended authorization - login and user level Version Available since: 2017/09/06 - Hotfix 13: Bugfixing o Removing products from the project table by using the DEL key is now no longer possible (undefined deletion) o Printing of profiles (Detail print) now complete (profiles consisting of single phases with a multiple of 16 were not printed completely) - Service Pack 8: o Global Function Live update (possible product variants) is permanently active Menue Settings Complete catalog program New product variant management integrated New action button Delete product selection integrated o Detail print Printing the new filter options for linear axes possible (Assembly work piece, installation dimensions)

9 Release Notes LinSelect 9 Version Available since: 2017/09/18 - Hotfix 14: Continuous optimization in the calculation algorithm / Bugfixing o Calculation of motor and drive controllers (parameter transfer interface Indrafunc.dll) o Resulting moment in the single phase "dwell time" o In the case of the product family CKR, the following error message could occur in certain constellations after jumping into the online configurator: "This selection is currently not implemented". The cause is fixed. - Service Pack 9: o Global Expansion/ preparation of the database structure for the integration of new product generations Version Available since: 2017/10/18 - Hotfix 15: Continuous optimization in the calculation algorithm / Bugfixing o Consideration of the resulting moments as filter for product families in step 4 (system) Accuracy / Stiffness now only from "increased requirement" (e.g., 2- rail systems, long carriage, etc.) o The "Start product search" key was released too early when the project was returned from the project view for post processing using "Product selection" or "Edit product selection". It was possible that the program crashed. This error has been fixed. - Service Pack 10: o Global In the steps Application, Design, Process, System and Product, the reasons for excluded product variants can be displayed on a graphical display due to the selected filter setting (relative number in the total number of systems in the database). Mouse-Click on the number of applicable product variants in the status line. New motion profile 1/6 (1/6 of the time acceleration, 4/6 of the time constant travel, 1/6 of the time deceleration) integrated. Optimized for mechanics. Available for linear axes and actuators. In the case of profile press in (only with actuator), the rapid movement was also adjusted (1/6 of the time acceleration, 4/6 of the time constant travel, 1/6 of the time deceleration). Better handling with the TAB key during profile press in o Result If there is no result after the calculation (no product), a window is displayed which graphically shows the absolute number of excluded and / or failed product variants with respect to "limit violations during calculation algorithm " and "post filters during calculation algorithm". When changing the name of the project or the linear system, an existing name is now displayed in the input box. Pressing the "Cancel" key now also retains the original name.

10 Release Notes LinSelect 10 Version Available since: 2017/11/27 - Hotfix 16: Continuous optimization in the calculation algorithm / Bugfixing o Updating the technical data base o Extension of the technical data base (MKX Gen.3) - Service Pack 11: o Global Splash information LinSelect now in in two languages (DE, EN) o Design Mounting dimensions "available mounting height workpiece (H)" not active in the default setting. If necessary, a value can be entered after activation with the check box Mounting dimensions "available installation length (L)" in the default setting not active and disable in preparation Direct textual description of the motion profiles o System Entering the service life performance (required nominal service life time L10) for ball screw, end bearing and guideway now possible up to 20 years o Update New Update-Application now in two languages (DE, EN)

11 Release Notes LinSelect 11 Version Available since: 2018/01/23 - Hotfix 18: Continuous optimization in the calculation algorithm / Bugfixing o Update database for technical data (Complement product family MKK-065/ - 080/ -110 (Gen. 3), MKR-065/ -080/ -110 (Gen. 3) o Calculation of motor and drive controller (Interface Indrafunc.dll modified) o Complement calculation algorithm for MKK-065/ -080/ -110 (Gen. 3), MKR- 065/ -080/ -110 (Gen. 3) - Service Pack 12: o Global New Indrafunc.dll / Sizebase.db3 integrated for the calculation of motor and controller Supplementing the query usage conditions (at the first start or after an update of LinSelect) with the confirmation of the correct country selection o Product With the introduction of the MS2N motors on the new MKK-065 / -080 / -110 (Gen. 3), MKR-065 / -080 / -110 (Gen. 3) moduls we revised the motor section in step product. There are now new input / options available: Motor family Holding break (with/ without) also possible in older versions Connectivity (2-wire, 1-wire) o Detail print Printing motor characteristics to motor option: Holding break Connectivity Cooling type Printing the product type plate with QR code and all important technical data: smax [mm], u [mm/umdr.], vmax [m/s], amax [m/s 2 ], M1max [Nm], d, i With the introduction of the new products MKK-065 / -080 / -110 (Gen. 3), MKR-065 / -080 / -110 (Gen. 3), the jump from LinSelect has been implemented in the new online configurator. o Update New update application. The update now preserves the following settings: Language also possible in older versions Country setting Window size Font size

12 Release Notes LinSelect 12 Version Available since: 2018/02/07 - Hotfix 19: Continuous optimization in the calculation algorithm / Bugfixing; Update / Bugfixing in the database o Updating the technical data base Supplement EMC-150-HD-1 with PLSA 60x20 (drive option 4) Completely new deduction of technical data and product key o Bugfixing when reworking incomplete linear systems When jump back to step 1-5, the status display remained at "0" linear systems despite changing the filter settings. This error is fixed. - Service Pack 13: o Design Help text adapted / expanded Help text adapted / expanded Linear axis: New message box due to moments around Mx, My or Mz resulting from the entered process steps / cycle regarding the options "Travel accuracy / Stiffness" in the step "System" Actuator: Note of a possible lateral force Fy under "Edit process step" in the tab "Forces" o System Help text adapted / expanded With the introduction of the new products MKK-080 / -110 (Gen. 3), MKR-080 / -110 (Gen. 3), the use of an integrated measuring system (IMS-A) offers another option for "Repeatability and position accuracy " to disposal In the project view, under menu item Project -> Send request -> by e- mail the user is able to send the current project directly. o Detail print Actuator: Print the note of a possible lateral force Fy and figure in the table Process Steps / Cycle Version Available since: 2018/02/13 - Hotfix 20: Continuous optimization in the calculation algorithm / Bugfixing; Update / Bugfixing in the database o Updating the technical data base

13 Release Notes LinSelect 13 Version Available since: 2018/02/22 - Hotfix 21: Continuous optimization in the calculation algorithm / Bugfixing; Update / Bugfixing in the database o Length calculation corrected. The following products were affected and can be recalculated with this version if necessary: MKK-080-NN-3, MKK-110-NN-3 MKR-080-NN-3, MKR-110-NN-3 Version Available since: 2018/03/05 - Hotfix 22: Continuous optimization in the calculation algorithm / Bugfixing; Update / Bugfixing in the database - Service Pack 14: Switching the display in tabular and / or graphic form Version Available since: 2018/04/09 - Hotfix 23: Continuous optimization in the calculation algorithm / Bugfixing; Update / Bugfixing in the database o Calculation max. permissible speed extended o Filter torque My o Error during jump into the online catalog (only linear modules Generation 3) has been corrected - Service Pack 15: o Global New button "Cancel" makes it possible to cancel editing / postprocessing of a linear system at any time. All original entries before editing are retained. The tool automatically jumps back to the project view. If no linear system was available, all entries are discarded and the tool returns to step 1 "Application". The two functions "save without result" and "send request" are now combined in a button "Send request / save without result" and in a window for selection. This possibility always exists if the tool can not suggest a possible product variant. Help texts are now displayed much more dosed (sometimes only once during the processing). Every motion profiles (for example Dwell time, 1/6 trapezoid, 1/3 trapezoid, trapezoid, etc.) can now be interchanged or replaced. Revision of the view "Edit process step" and the representation "Process step / cycle".

14 Release Notes LinSelect 14 There is one new button "Online Catalog" Opens a new window for the jump into the online catalog in which the catalog pages of the linear system, the motor on the linear system and the dimensioned drive controller can be opened. Version Available since: 2018/04/11 - Hotfix 24: Continuous optimization in the calculation algorithm / Bugfixing; Update / Bugfixing in the database o Calculation of motor and drive controllers (parameter transfer interface Indrafunc.dll)