NuMaker M487 Advance

Transcription

1 ARM Cortex -M 3-bit Microcontroller NuMaker M487 Advance User Manual NuMicro M480 Series The information described in this document is the exclusive intellectual property of Nuvoton Technology Corporation and shall not be reproduced without permission from Nuvoton. Nuvoton is providing this document only for reference purposes of NuMicro microcontroller based system design. Nuvoton assumes no responsibility for errors or omissions. All data and specifications are subject to change without notice. For additional information or questions, please contact: Nuvoton Technology Corporation. June 5, 08 Page of 5 Rev.00

2 Table of Contents Overview Brief Introduction to NuMaker-PFM-M487 Board The Target Chip M487JIDAE MCU Features... 6 NuMaker M487 Advance Board Overview Front View Rear View The Connectors of NuMaker-PFM-M487 Board PCB Placement NuMaker M487 Advance Schematics Header Connectors QVGA TFT LCD Module with Touch SRAM (IS6WV56B) I C EEPROM (4LC64) I C MEMS (MPU6500) Joystick, Key Buttons, Buzzer, IO and LED Mikro Bus CAN and RS REVISION HISTORY... 4 June 5, 08 Page of 5 Rev.00

3 List of Figures Figure - Combination of NuMaker M487 Advance Board and NuMaker-PFM-M487 Board... 5 Figure - NuMaker-PFM-M487 Board... 6 Figure - Front View of NuMaker M487 Advance Board... 8 Figure - Rear View of NuMaker M487 Advance Board... 9 Figure -3 Connectors of NuMaker-PFM-M Figure -4 Front Placement... 5 Figure -5 Rear Placement... 5 Figure 3- Header Connectors... 6 Figure 3- QVGA TFT LCD Module with Touch Circuit... 7 Figure 3-3 SRAM Circuit... 8 Figure 3-4 I C EEPROM Circuit... 9 Figure 3-5 I C MEMS Circuit... 0 Figure 3-6 Joystick, Key Buttons, Buzzer, IO and LED Circuit... Figure 3-7 Mikro Bus Circuit... Figure 3-8 CAN and RS485 Circuit... 3 June 5, 08 Page 3 of 5 Rev.00

4 List of Tables Table - Connector JP Mapping to Connector JP6 of NuMaker-PFM-M Table - Connector JP3 Mapping to Connector JP8 of NuMaker-PFM-M Table -3 Connector JP Mapping to Connector JP7 of NuMaker-PFM-M Table -4 Connector JP4 Mapping to Connector JP9 of NuMaker-PFM-M June 5, 08 Page 4 of 5 Rev.00

5 OVERVIEW This user manual is aimed to give users a fast introduction to the NuMaker M487 Advance (Ver 4.0) board. This board is a daughter board and it can t work independently by itself. It needs to be combined with the NuMaker-PFM-M487 (Ver 3.0) development board to implement some dedicated applications, for example the TFT LCD display with touch function, MB SRAM, MPU6500, I C EEPROM, Mikro Bus, RS485 and CAN bus, etc., based on the target chip M487JIDAE microcontroller on the NuMaker-PFM-M487 board. Figure - shows the combination picture of NuMaker M487 Advance board (top) and NuMaker-PFM- M487 board (bottom).. Figure - Combination of NuMaker M487 Advance Board and NuMaker-PFM-M487 Board Brief Introduction to NuMaker-PFM-M487 Board The NuMaker-PFM-M487 is a development board based on an ARM Cortex -M4 microcontroller (MCU) M480 series which has very rich peripherals to help users easily to design-in their products or application systems. This board is provided by Nuvoton and created specially to support the ARM mbed IoT Device Platform, and let user easily to develop the IoT application program on this board. The NuMaker-PFM- M487 also provides user many useful and powerful learning materials for how to develop and verify the application programs through the peripherals and interfaces on MCU and this board. The NuMaker-PFM-M487 board consists of M487 Platform and Nu-Link-Me ICE Bridge. Figure - shows the NuMaker-PFM-M487 board. For more detailed information on the NuMaker-PFM-M487 board, please visit Nuvoton NuMicro Family ARM Cortex -M4 MCUs User Manual website: Manual/? locale=en&resourcepage=y June 5, 08 Page 5 of 5 Rev.00

6 Figure - NuMaker-PFM-M487 Board. The Target Chip M487JIDAE MCU Features LQFP44 package ARM Cortex -M4 core running up to 9 MHz with DSP extensions and FPU (Floating Point Unit) Built-in LDO for wide operating voltage ranged from.8 V to 3.6 V 5 Kbytes Flash 60 Kbytes SRAM External Bus Interface (EBI) GPIO Peripheral DMA (PDMA) Timer EPWM and BPWM Quadrature Encoder Interface (QEI) WDT and WWDT RTC UART Smart Card (ISO-786-3) Host Interface I C SPI SPIM (SPI Master) I S Universal Serial Control Interface (USCI) USB.0 High-Speed OTG / Host / Device June 5, 08 Page 6 of 5 Rev.00

7 USB. Full-Speed OTG / Host / Device CAN.0 Ethernet MAC SD Host Cryptographic Accelerator CRC ADC DAC Comparator OPA June 5, 08 Page 7 of 5 Rev.00

8 NUMAKER M487 ADVANCE BOARD OVERVIEW. Front View Figure - shows the main components and connectors from the front side of NuMaker M487 Advance board. The following lists components and connectors from the front view: QVGA TFT LCM with Touch: LCDT (J, driver ILI934) SRAM: IS6WV56B (U3, M bytes) I C EEPROM: 4LC64 (U4) Motion Tracking Device: MPU6500 (U5) CAN Transceiver: SN65HVD30 (U6) RS485 Transceiver: SN65HVDDR (U7) Joystick (J) Mikro Bus (J3 and J4) Buzzer (BZ) LEDs (LEDG and LEDR) Push-buttons (SW and SW) Multi-function Switches (SW3) Joystick (J) SW SW GPIO IO/IO (JP7) QVGA TFT LCM with Touch (J) LED (LEDG/LEDR) SW3 SRAM (U3) RS485 Transceiver (U7) Connector (JP6) Mikro Bus (J3/J4) MPU6500 (U5) Buzzer (BZ) EEPROM (U4) CAN Transceiver (U6) Connector (JP5) Figure - Front View of NuMaker M487 Advance Board June 5, 08 Page 8 of 5 Rev.00

9 . Rear View Figure - shows the main components and connectors from the rear side of NuMaker M487 Advance board. The following lists connectors from the rear view: Header Connectors: JP, JP, JP3 and JP4 for the NuMaker-PFM-M487 board Octal D-type Transparent Latch Device: 74HC373 (U and U) JP JP4 74HC373 (U/U) JP3 JP Figure - Rear View of NuMaker M487 Advance Board June 5, 08 Page 9 of 5 Rev.00

10 .3 The Connectors of NuMaker-PFM-M487 Board The NuMaker-PFM-M487 board provides the M487JIDAE target chip onboard and extended connectors (JP6, JP7, JP8 and JP9) for LQFP44-pin. The Figure -3 shows the M487JIDAE extended connectors on the NuMaker-PFM-M487 board that should be connected to NuMaker M487 Advance board. The Table - to Table -4 shows the mapping tables on these connector headers of these two boards. Figure -3 Connectors of NuMaker-PFM-M487 June 5, 08 Page 0 of 5 Rev.00

11 Table - Connector JP Mapping to Connector JP6 of NuMaker-PFM-M487 Header M487 M487 PFM Advance Board Header M487 M487 PFM Advance Board GPIO Function Function GPIO Function Function JP. PB.5 SD0_DAT3 - JP. PB.4 SD0_DAT - JP.3 PB.3 - IO (JP7) JP.4 PB. OPA0_O EPWM0_CH3* JP.5 PC. - SPI3_MISO JP.6 PC. - SPI3_MOSI JP.7 PC.0 - Down (Joystick) JP.8 PC.9 - Left (Joystick) JP.9 PB. OPA0_N IC_SCL* JP.0 PB.0 OPA0_P IC_SDA* JP. VSS JP. VDD 3 3 JP.3 PA. - A8 (SRAM) JP.4 PA.0 OPA_O A7* (SRAM) JP.5 PA.9 OPA_N A6* (SRAM) JP.6 PA.8 OPA_P EBI_ALE* (SRAM) JP JP.7 PC.3 JKDET - JP JP.8 PD. OPA_O BPWM0_CH5* (Buzzer) JP.9 PD. OPA_N EBI_nCS* INT7* JP.0 PD.0 OPA_P (SRAM) JP. VSS JP. VDD 3 3 JP.3 PG.0 - UART_TXD UART_RXD JP.4 PG. - Up Center JP.5 PG. - (Joystick) JP.6 PG.3 - (Joystick) Right JP.7 PG.4 - (Joystick) JP.8 PF. SW3 - JP.9 PF.0 IS0_BCLK - JP.30 PF.9 IS0_MCLK - JP.3 PF.8 IS0_DI - JP.3 PF.7 IS0_DO - JP.33 PF.6 IS0_LRCK - JP.34 VBAT VBAT - JP.35 PF.5 XT3_IN - JP.36 PF.4 XT3_OUT - Note : These pins share the same GPIO pins with those dedicated pin-functions on the NuMaker-PFM-M487 board. Please make sure these related resistors are open (these resistors are NC in default) on the NuMaker-PFM-M487 board and switch all ON for these pins on the SW3 of the MuMaker M487 Advance board to implement the application functions on this NuMaker M487 Advance board. June 5, 08 Page of 5 Rev.00

12 Table - Connector JP3 Mapping to Connector JP8 of NuMaker-PFM-M487 Header M487 M487 PFM Advance Board Header M487 M487 PFM Advance Board GPIO Function Function GPIO Function Function JP3. PH.0 LEDR* 3 UART5_TXD * (RS485) JP3. PH. LEDY* 3 UART5_RXD* (RS485) JP3.3 PH. LEDG* 3 UART5_nRTS * (RS485) JP3.4 PH.3 - LCD_RS (LCD) JP3.5 PH.4 - LCD_XL (LCD) JP3.6 PH.5 - LCD_YD (LCD) JP3.7 PH.6 - LED (LEDR) JP3.8 PH.7 - LED (LEDG) JP3.9 PF.3 XT_IN - JP3.0 PF. XT_OUT - JP3. VSS JP3. VDD 3 3 JP3.3 PE.8 EMAC_MDC - JP3.4 PE.9 EMAC_MDIO - JP3.5 PE.0 EMAC_TXD0 - JP3.6 PE. EMAC_TXD - JP3.7 PE. EMAC_TXEN - JP3.8 PE.3 #JKEN - JP3 JP3.9 PC.8 EMAC_REFCLK - JP3 JP3.0 PC.7 EMAC_RXD0 - JP3. PC.6 EMCAC_RXD - JP3. PA.7 EMAC_RXDV - JP3.3 PA.6 EMAC_RXERR - JP3.4 VSS JP3.5 VDD 3 3 JP3.6 LDO LDO_CAP - JP3.7 PA.5 - CAN0_TXD (CAN) JP3.8 PA.4 - CAN0_RXD (CAN) JP3.9 PA.3 - C (CAN) JP3.30 PA. - C (CAN) JP3.3 PA. - SW (Key button) JP3.3 PA.0 - SW (Key button) JP3.33 VDDIO VDDIO EBI_AD8 - JP3.34 PE.4 - JP3.35 PE.5 - EBI_AD9 RST JP3.36 nreset nreset Note : These LEDs (LEDR, LEDY and LEDG) of NuMaker-PFM-M487 board share the same pins (PH.0, PH. and PH.) with these RS485 signals (UART5_TXD, UART5_RXD and UART5_nRTS) of NuMaker M487 Advance board. When RS485 function is running on NuMaker M487 Advance board, user can ignore the status of these LEDs on NuMaker-PFM-M487 board. June 5, 08 Page of 5 Rev.00

13 Table -3 Connector JP Mapping to Connector JP7 of NuMaker-PFM-M487 Header M487 M487 PFM Advance Board Header M487 M487 PFM Advance Board GPIO Function Function GPIO Function Function JP. PF.0 ICEDAT - JP. PF. ICECLK - JP.3 PD.9 - EBI_AD7 JP.4 PD.8 - EBI_AD6 JP.5 PC.5 SPIM_D - JP.6 PC.4 SPIM_D3 - JP.7 PC.3 SPIM_SS - JP.8 PC. SPIM_CLK - JP.9 PC. SPIM_MISO - JP.0 PC.0 SPIM_MOSI - JP. VSS JP. VDD 3 3 JP.3 PG.9 - EBI_AD0 JP.4 PG.0 - EBI_AD JP.5 PG. - EBI_AD JP.6 PG. - EBI_AD3 JP.7 PG.3 - EBI_AD4 JP.8 PG.4 - EBI_AD5 JP JP.9 PG.5 SW - JP.0 PD.3 - JP. PD. - JP.3 PD.0 IC_SDA JP.5 PA. USB_VBUS INT (MPU6500) IC_SDA (MPU6500/ EEPROM) 5V_IN JP JP. PD. IC_SCL JP.4 PD. SD0_nCD IO (JP7) IC_SCL (MPU6500/ EEPROM) JP.6 PA.3 USB_D- - JP.7 PA.4 USB_D+ - JP.8 PA.5 USB_OTG_ID - JP.9 HSUSB_VR ES JP.3 HSUSB_VB US HSUSB_VRES - JP.30 HSUSB_VDD 33 HSUSB_VBUS 5V_IN HSUSB_VDD3 3 JP.3 HSUSB_D- HSUSB_D- - - JP.33 HSUSB_VS S HSUSB_VSS - JP.34 HSUSB_D+ HSUSB_D+ - JP.35 HSUSB_VD D_CAP HSUSB_VDD _CAP - JP.36 HSUSB_ID HSUSB_ID - June 5, 08 Page 3 of 5 Rev.00

14 Table -4 Connector JP4 Mapping to Connector JP9 of NuMaker-PFM-M487 Header M487 M487 PFM Advance Board Header M487 M487 PFM Advance Board GPIO Function Function GPIO Function Function JP4. PE.7 SD0_CMD - JP4. PE.6 SD0_CLK - JP4.3 PE.5 - EBI_nRD JP4.4 PE.4 - EBI_nWR JP4.5 PE.3 SD0_DAT - JP4.6 PE. SD0_DAT0 - JP4.7 VSS JP4.8 VDD 3 3 JP4.9 PE. - EBI_AD0 JP4.0 PE.0 - EBI_AD JP4. PH.8 - EBI_AD JP4. PH.9 - EBI_AD3 JP4.3 PH.0 - EBI_AD4 JP4.4 PH. - EBI_AD5 JP4.5 PD.4 - EBI_nCS0 (LCD) JP4.6 PG.5 - SPI3_SS JP4 JP4.7 PG.6 - SPI3_CLK JP4 JP4.8 PG.7 - EBI_nWRL (SRAM) JP4.9 PG.8 - EBI_nWRH (SRAM) JP4.0 VSS JP4. LDO LDO_CAP - JP4. VDD 3 3 JP4.3 PC.4 USB_VBUS_ST - JP4.4 PB.5 USB_VBUS_EN - JP4.5 PB.4 EADC0_CH4 EADC0_CH4 *3 JP4.6 PB.3 UART0_TXD - JP4.7 PB. UART0_RXD - JP4.8 AVDD AVDD AVDD JP4.9 VREF VREF - JP4.30 AVSS ADAVSS AVSS JP4.3 PB. HSUSB_VBUS_ST - JP4.3 PB.0 HSUSB_VBUS_EN - JP4.33 PB.9 - JP4.35 PB.7 - LCD_XR (LCD) LCD_BL (LCD) JP4.34 PB.8 - JP4.36 PB.6 - LCD_YU (LCD) LCD_RESET (LCD) Note 3: This pin shares the same GPIO pin with the dedicated pin-function on the NuMaker-PFM-M487 board. Please make sure this related resistor is open (the resistor is NC in default) on the NuMaker-PFM-M487 board and switch ON for this pin on the SW3 of the MuMaker M487 Advance board to implement the application function on this NuMaker M487 Advance board. June 5, 08 Page 4 of 5 Rev.00

15 .4 PCB Placement Figure -4 and Figure -5 show the front and rear placement of NuMaker M487 Advance board. Figure -4 Front Placement Figure -5 Rear Placement June 5, 08 Page 5 of 5 Rev.00

16 ~ ~ ~ ~ MuMaker M487 Advance 3 NUMAKER M487 ADVANCE SCHEMATICS 3. Header Connectors Figure 3- shows the all the header connecters JP~JP4 that should be connected to the header connectors JP6~JP9 of NuMaker-PFM-M487 board. For the SW3 switches, there are ten pins share the same GPIO pins with those dedicated pin-functions on the NuMaker-PFM-M487 board. Please make sure these related resistors are open (these resistors are NC in default) on the NuMaker-PFM- M487 board (Ver 3.0) and switch all ON for these pins on this SW3 to implement the application functions on the NuMaker M487 Advance board. P P3 P5 P7 P9 P P3 P5 P7 P9 P P3 P5 P7 P9 P3 P33 P35 P37 P39 P4 P43 P45 P47 P49 P5 P53 P55 P57 P59 P6 P63 P65 P67 P69 P7 JP JP P P73 P P4 P P P6 P P P8 P P P0 P8 9 0 P8 P P83 P P4 P P P6 P P P8 P P P0 P9 9 0 P9 P P93 P P4 P P P6 P P P8 P P P30 P P0 3 3 P3 P P P34 P P P36 P P08 HEADER.54 8X SMD (male) HEADER.54 8X SMD (male) MCU CONNECTOR JP3 JP4 P38 P09 P0 3 4 P40 P 3 4 P 5 6 P4 P3 5 6 P4 7 8 P44 P5 7 8 P6 9 0 P46 P7 9 0 P8 P48 P9 P0 3 4 P50 P 3 4 P 5 6 P5 P3 5 6 P4 7 8 P54 P5 7 8 P6 9 0 P56 P7 9 0 P8 P58 P9 P P60 P3 3 4 P3 5 6 P6 P P P64 P P P66 P P P68 P P P70 P P P7 P P44 HEADER.54 8X SMD (male) SW3 P4 PB. EPWM0_CH3 PB_ P9 PB. IC_SCL PB_ P0 PB.0 IC_SDA PB_0 P4 PA.0 SRAM A7 PA_0 P5 PA.9 SRAM A6 PA_9 P6 PA.8 EBI_ALE PA_8 P8 PD. BPWM0_CH5 PD_ P9 PD. EBI_nCS PD_ P0 PD.0 INT7 PD_0 P33 PB.4 EADC0_CH4 PB_4 Default: All ON SWDIP0 (SMD, all ON) Title NuMaker M487 Advance (LV) Size Document Number Rev A4 MCU Connectors V4.0 Date: Tuesday, April 4, 08 Sheet of 6 8 HEADER.54 8X SMD (male) MCU Connector Off-page P P36 P37 P7 PB_ EPWM0_CH3 EPWM0_CH3 PB_ IC_SCL IC_SCL PB_0 IC_SDA IC_SDA PA_0 SRAM_A7 SRAM_A7 PA_9 SRAM_A6 SRAM_A6 PA_8 EBI_ALE EBI_ALE PD_ BPWM0_CH5 EBPWM0_CH5 PD_ EBI_nCS EBI_nCS PD_0 INT7 INT7 PB_4 EADC0_CH4 EADC0_CH4 P PB.5 P P PB.4 P P3 PB.3 P3 P4 PB. P4 P5 PC. P5 P6 PC. P6 P7 PC.0 P7 P8 PC.9 P8 P9 PB. P9 P0 PB.0 P0 P VSS P P VDD P P3 PA. P3 P4 PA.0 P4 P5 PA.9 P5 P6 PA.8 P6 P7 PC.3 P7 P8 PD. P8 P9 PD. P9 P0 PD.0 P0 P VSS P P VDD P P3 PG.0 P3 P4 PG. P4 P5 PG. P5 P6 PG.3 P6 P7 PG.4 P7 P8 PF. P8 P9 PF.0 P9 P30 PF.9 P30 P3 PF.8 P3 P3 PF.7 P3 P33 PF.6 P33 P34 VBAT P34 P35 PF.5 P35 P36 PF.4 P36 P37 PH.0 P37 P38 PH. P38 P39 PH. P39 P40 PH.3 P40 P4 PH.4 P4 P4 PH.5 P4 P43 PH.6 P43 P44 PH.7 P44 P45 PF.3 P45 P46 PF. P46 P47 VSS P47 P48 VDD P48 P49 PE.8 P49 P50 PE.9 P50 P5 PE.0 P5 P5 PE. P5 P53 PE. P53 P54 PE.3 P54 P55 PC.8 P55 P56 PC.7 P56 P57 PC.6 P57 P58 PA.7 P58 P59 PA.6 P59 P60 VSS P60 P6 VDD P6 P6 LDO_CAP P6 P63 PA.5 P63 P64 PA.4 P64 P65 PA.3 P65 P66 PA. P66 P67 PA. P67 P68 PA.0 P68 P69 VDDIO P69 P70 PE.4 P70 P7 PE.5 P7 P7 nreset P7 Figure 3- Header Connectors P73 P74 P75 P76 P77 P78 P79 P80 P8 P73 P8 P83 P84 P85 P86 P87 P88 P89 P90 P08 P9 P9 P93 P94 P95 P96 P97 P98 P99 P00 P0 P0 P03 P04 P05 P06 P07 P08 P09 P0 P P P3 P4 P5 P09 P6 P7 P8 P9 P0 P P P3 P4 P44 P5 P6 P7 P8 P9 P30 P3 P3 P33 P34 P35 P36 P37 P38 P39 P40 P4 P4 P43 P44 P73 PF.0 P74 PF. P75 PD.9 P76 PD.8 P77 PC.5 P78 PC.4 P79 PC.3 P80 PC. P8 PC. P8 PC.0 P83 VSS P84 VDD P85 PG.9 P86 PG.0 P87 PG. P88 PG. P89 PG.3 P90 PG.4 P9 PG.5 P9 PD.3 P93 PD. P94 PD. P95 PD.0 P96 PD.3 P97 PA. P98 PA.3 P99 PA.4 P00 PA.5 P0 HSUSB_VRES P0 HSUSB_VDD33 P03 HSUSB_VBUS P04 HSUSB_D- P05 HSUSB_VSS P06 HSUSB_D+ P07 HSUSB_VDD_CAP P08 HSUSB_ID P09 PE.7 P0 PE.6 P PE.5 P PE.4 P3 PE.3 P4 PE. P5 VSS P6 VDD P7 PE. P8 PE.0 P9 PH.8 P0 PH.9 P PH.0 P PH. P3 PD.4 P4 PG.5 P5 PG.6 P6 PG.7 P7 PG.8 P8 VSS P9 LDO_CAP P30 VDD P3 PC.4 P3 PB.5 P33 PB.4 P34 PB.3 P35 PB. P36 AVDD P37 VREF P38 AVSS ADAVSS P39 PB. P40 PB.0 P4 PB.9 P4 PB.8 P43 PB.7 P44 PB.6 June 5, 08 Page 6 of 5 Rev.00

17 3. QVGA TFT LCD Module with Touch Figure 3- shows the QVGA TFT LCD module with touch circuit and the related EBI interface and GPIO control pins. Title TFT LCD Off-page P P P3 P P P0 P9 P8 P7 P7 P70 P75 P76 P90 P89 P88 P87 P86 P85 P40 P44 P43 P4 P4 P4 P4 P PE.5 P PE.4 P3 PD.4 P PH. P PH.0 P0 PH.9 P9 PH.8 P8 PE.0 P7 PE. P7 PE.5 P70 PE.4 P75 PD.9 P76 PD.8 P90 PG.4 P89 PG.3 P88 PG. P87 PG. P86 PG.0 P85 PG.9 P40 PH.3 P44 PB.6 P43 PB.7 P4 PB.9 P4 PB.8 P4 PH.4 P4 PH.5 EBI_nRD EBI_nWR EBI_nCS0 EBI_AD5 EBI_AD4 EBI_AD3 EBI_AD EBI_AD EBI_AD0 EBI_AD9 EBI_AD8 EBI_AD7 EBI_AD6 EBI_AD5 EBI_AD4 EBI_AD3 EBI_AD EBI_AD EBI_AD0 LCD_RS LCD_RESET LCD_BL LCD_XR LCD_YU LCD_XL LCD_YD NuMaker M487 Advance (LV) Size Document Number Rev A4 TFT LCD Module V4.0 Date: Monday, April 3, 08 Sheet of 8 LCD_BL TFT LCD CB6 0.u S8050 (NPN) Figure 3- QVGA TFT LCD Module with Touch Circuit R CB7 0.u K N CB5 0.u 3 Q EBI_AD0 EBI_AD EBI_AD EBI_AD3 EBI_nCS0 LCD_RS EBI_nWR EBI_nRD LCD_XL LCD_YU LCD_XR LCD_YD LEDK EBI_AD4 EBI_AD8 EBI_AD9 EBI_AD0 EBI_AD EBI_AD EBI_AD3 EBI_AD4 EBI_AD5 LCD_RESET EBI_AD5 EBI_AD6 EBI_AD J PFC CONN 37-pin (0.8 pitch) June 5, 08 Page 7 of 5 Rev.00

18 0 0 MuMaker M487 Advance 3.3 SRAM (IS6WV56B) Figure 3-3 shows the SRAM (IS6WV56B) circuit that can be accessed by M487 MCU through the EBI bus. But, the MSB address pins A6/A7/A8 to the SRAM are controlled by the GPIO (PA.9, PA.0 and PA.) through the firmware controlled. These pins are not drove by the EBI bus directly. SRAM Off-page P3 SRAM_A7 SRAM_A6 P6 P7 EBI_ALE EBI_nCS P P P P P0 P9 P8 P7 P7 P70 P75 P76 P90 P89 P88 P87 P86 P85 P3 PA. SRAM_A8 PA_0 SRAM_A7 PA_9 SRAM_A6 P6 PG.7 P7 PG.8 PA_8 PD_ P PE.5 P PE.4 P PH. P PH.0 P0 PH.9 P9 PH.8 P8 PE.0 P7 PE. P7 PE.5 P70 PE.4 P75 PD.9 P76 PD.8 P90 PG.4 P89 PG.3 P88 PG. P87 PG. P86 PG.0 P85 PG.9 EBI_nWRL EBI_nWRH EBI_ALE EBI_nCS EBI_nRD EBI_nWR EBI_AD5 EBI_AD4 EBI_AD3 EBI_AD EBI_AD EBI_AD0 EBI_AD9 EBI_AD8 EBI_AD7 EBI_AD6 EBI_AD5 EBI_AD4 EBI_AD3 EBI_AD EBI_AD EBI_AD0 NOTE: SRAM address bus A6/A7/A8 are GPIO-controlled by MCU firmware. Not EBI hardware interface directly to drive. EBI_AD0 EBI_AD EBI_AD EBI_AD3 EBI_AD4 EBI_AD5 EBI_AD6 EBI_AD7 EBI_ALE 0 U 3 4 D0 7 D 8 D 3 D3 4 D4 7 D5 8 D6 D7 LE OE Q0 5 Q 6 Q 9 Q3 Q4 5 Q5 6 Q6 9 Q7 74HC373 SOP0\.7- CB 0.u SRAM_A0 SRAM_A SRAM_A SRAM_A3 SRAM_A4 SRAM_A5 SRAM_A6 SRAM_A7 EBI_AD8 EBI_AD9 EBI_AD0 EBI_AD EBI_AD EBI_AD3 EBI_AD4 EBI_AD5 EBI_ALE 0 U 3 4 D0 7 D 8 D 3 D3 4 D4 7 D5 8 D6 D7 LE OE Q0 5 Q 6 Q 9 Q3 Q4 5 Q5 6 Q6 9 Q7 74HC373 SOP0\.7- CB 0.u SRAM_A8 SRAM_A9 SRAM_A0 SRAM_A SRAM_A SRAM_A3 SRAM_A4 SRAM_A5 CB3 0.u SRAM_A4 SRAM_A3 SRAM_A SRAM_A SRAM_A0 EBI_nCS EBI_AD0 EBI_AD EBI_AD EBI_AD3 EBI_AD4 EBI_AD5 EBI_AD6 EBI_AD7 EBI_nWR SRAM_A6 SRAM_A5 SRAM_A4 SRAM_A3 SRAM_A U3 A4 3 A3 4 A 5 A 6 A0 7 CS 8 I/O0 9 I/O 0 I/O I/O3 VDD 3 4 I/O4 5 I/O5 6 I/O6 7 I/O7 8 WE 9 A6 0 A5 A4 A3 A 44 A5 43 A6 A7 4 4 OE 40 UB 39 LB 38 I/O5 37 I/O4 36 I/O3 I/O VDD 3 I/O 3 I/O0 30 I/O9 9 I/O8 8 A8 7 A8 6 A9 5 A0 4 A 3 A7 IS6WV56BLL/400mil SRAM_A5 SRAM_A6 SRAM_A7 EBI_nRD EBI_nWRH EBI_nWRL EBI_AD5 EBI_AD4 EBI_AD3 EBI_AD EBI_AD EBI_AD0 EBI_AD9 EBI_AD8 SRAM_A8 SRAM_A8 SRAM_A9 SRAM_A0 SRAM_A SRAM_A7 CB4 0.u Figure 3-3 SRAM Circuit SRAM Title NuMaker M487 Advance (LV) Size Document Number Rev A SRAM V4.0 Date: Tuesday, April 4, 08 Sheet of 8 June 5, 08 Page 8 of 5 Rev.00

19 3.4 I C EEPROM (4LC64) Figure 3-5 shows the I C EEPROM (4LC64) circuit. EEPROM Off-page P94 P95 P94 P95 PD. PD.0 IC_SCL IC_SDA EEPROM ADDRESS: 50H U4 IC-EEPROM 8 A0 7 3 A WP 6 4 A SCL 5 SDA 4LC64 R NC R3 NC IC_SCL IC_SDA IC EEPROM Title NuMaker M487 Advance (LV) Size Document Number Rev A IC EEPROM V4.0 Date: Friday, May 5, 08 Sheet 3 of 8 Figure 3-4 I C EEPROM Circuit June 5, 08 Page 9 of 5 Rev.00

20 AUX_CL VDDIO SDO/AD0 REGOUT FSYNC INT SDA/SDI SCL/SCLK ncs AUX_DA RESV RESV MuMaker M487 Advance 3.5 I C MEMS (MPU6500) Figure 3-5 shows the I C MEMS (MPU6500) circuit. 3-Axis ACC, 3-Axis Gyor MEMS Off-page IC_SCL IC_SDA MPU6500 ADDRESS: 68H U5 P94 P95 P93 P94 P95 P93 PD. PD.0 PD. IC_SCL IC_SDA MPU6500_INT NC NC NC NC NC NC MPU NC 7 NC 6 NC 5 NC 4 VDD 3 CB8 0.u C 0nF CB9 0.u MPU6500_INT R4 0K IC MEMS Title Figure 3-5 I C MEMS Circuit NuMaker M487 Advance (LV) Size Document Number Rev A MEMS (MPU6500) V4.0 Date: Friday, June 08, 08 Sheet 4 of 8 June 5, 08 Page 0 of 5 Rev.00

21 N4 N5 N3 3 MuMaker M487 Advance 3.6 Joystick, Key Buttons, Buzzer, IO and LED Figure 3-6 shows the joystick, key buttons, buzzer, IO and LED circuit. R5 0K SW SW PUSH BUTTON SW4-SMD Key R6 0K SW SW PUSH BUTTON SW4-SMD R9 0k R7 0k Lef t Center J CONN MOD 6-6_J Joystick R8 0k Up Right Down R0 0k R 0k Joystick/LED/Key/Buzzer Off-page P5 P6 P7 P7 P8 P43 P44 P67 P68 P3 P9 P5 PG. Up P6 PG.3 Center P7 PG.4 Right P7 PC.0 Down P8 PC.9 Lef t P43 PH.6 LED P44 PH.7 LED P67 PA. SW P68 PA.0 SW P3 PB.3 IO P9 PD.3 IO PD_ BPWM0_CH5 BUZZER EBPWM0_CH5 CB0 0.u CB 0.u BUZZER R 33 N Q S8550 (PNP) R3 330R R4 330R JP8 X HEADER(NC) Power JP9 X HEADER(NC) Base S Collector Emitter Buzzer BUZZER BZ LF-MBA05(400Hz) LEDG LEDR LED Green(LED0805) LED LED Red(LED0805) IO IO JP7 X HEADER(NC) GPIO Figure 3-6 Joystick, Key Buttons, Buzzer, IO and LED Circuit Title NuMaker M487 Advance (LV) Size Document Number Rev A Joystick, LED, Keys and Buzzer V4.0 Date: Friday, April 7, 08 Sheet 5 of 8 June 5, 08 Page of 5 Rev.00

22 3.7 Mikro Bus Figure 3-7 shows the Mikro Bus circuit. Mikro Bus Off-page AN RST CS SCK MISO MOSI +3.3V J HEADER8 (female) EADC0_CH4 RST SPI3_SS SPI3_CLK SPI3_MISO SPI3_MOSI PWM INT RX TX SCL SDA +5V J HEADER8 (female) EPWM0_CH3 INT7 UART_RXD UART_TXD IC_SCL IC_SDA 5V_IN EPWM0_CH3 IC_SCL IC_SDA INT7 EADC0_CH4 P3 P4 P4 P5 P5 P6 P7 P97 P03 PB_ PB_ PB_0 PD_0 PB_4 EPWM0_CH3 IC_SCL IC_SDA INT7 EADC0_CH4 P3 PG.0 UART_TXD P4 PG. UART_RXD P4 PG.5 SPI3_SS P5 PG.6 SPI3_CLK P5 PC. SPI3_MISO P6 PC. SPI3_MOSI P7 nreset RST P97 PA. 5V_IN P03 HSUSB_VBUS 5V_IN Mikro Bus Title NuMaker M487 Advance (LV) Size Document Number Rev A Mikro Bus V4.0 Date: Friday, June 08, 08 Sheet 7 of 8 Figure 3-7 Mikro Bus Circuit June 5, 08 Page of 5 Rev.00

23 3.8 CAN and RS485 Figure 3-8 shows CAN and RS485 circuit. CAN and RS485 Off-page P63 P64 P65 P66 P37 P38 P39 P63 P64 P65 P66 P37 P38 P39 PA.5 PA.4 PA.3 PA. PH.0 PH. PH. CB 0.u CAN0_TXD CAN0_RXD C C RS485_TXD RS485_RXD RS485_nRTS CAN0_TXD CAN0_RXD U6 D 3 4 R 8 Rs CANH 7 6 CANL 5 Vref SO-8 SN65HVD30 R5 0K R6 0R C C CANH CANL CANL CANH CANL CANH CAN HEADER X (male) 90 degrees HD-35-0P JP5 X HEADER(male) RS485_RXD RS485_nRTS RS485_TXD R8 0K U7 RO 3 RE 4 DE DI SO-8 8 B 7 A 6 5 SN65HVDDR RS485_B3 RS485_A3 CB3 0.u RS485_A3 RS485_B3 R7 0R RS485_A3 RS485_B3 RS485_A3 RS485_B3 RS485 HEADER X (male) 90 degrees HD-35-0P JP6 X HEADER(male) CAN and RS485 Figure 3-8 CAN and RS485 Circuit Title NuMaker M487 Advance (LV) Size Document Number Rev A CAN and RS485 V4.0 Date: Monday, April 3, 08 Sheet 8 of 8 June 5, 08 Page 3 of 5 Rev.00

24 4 REVISION HISTORY Date Revision Description Initially issued. June 5, 08 Page 4 of 5 Rev.00

25 Important Notice Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any malfunction or failure of which may cause loss of human life, bodily injury or severe property damage. Such applications are deemed, Insecure Usage. Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic energy control instruments, airplane or spaceship instruments, the control or operation of dynamic, brake or safety systems designed for vehicular use, traffic signal instruments, all types of safety devices, and other applications intended to support or sustain life. All Insecure Usage shall be made at customer s risk, and in the event that third parties lay claims to Nuvoton as a result of customer s Insecure Usage, customer shall indemnify the damages and liabilities thus incurred by Nuvoton. June 5, 08 Page 5 of 5 Rev.00