CONFIGURATION MANUAL MAGLINK LX

Transcription

1 CONFIGURATION MANUAL MAGLINK LX Rev. 09 April 2016

2 This page is left intentionally blank.

3 Configuration Manual Summary SUMMARY 1 PREFACE GENERAL WARNINGS INTRODUCTION LOGIN PROCEDURE BASIC FUNCTIONS CHANGE PASSWORD THE "GUEST" AND "ADMIN" PAGES HISTORY ALARMS DELIVERY/LOSSES CURRENT STATUS SENSOR STATUS THE "ADMIN" PAGE SYSTEM TANK STRAPPING TABLE RELAYS SENSORS RECONCILIATION SHIFT REPORT DISPENSER CONFIGURATION TCP/IP CONNECTION CONFIGURATION PRINT STOCK CONFIGURATION MODEM CONFIGURATION SETTINGS UTILITY SUPPORT REVISIONS...26 Rev. 09, April 2016 Page 3 of 28

4 Configuration Manual Preface 1 PREFACE Start Italiana S.r.l. has made every effort to keep this document complete, accurate and updated. With every revision of the console, the corresponding information is periodically added to the document. Start Italiana S.r.l. reserves the right to make unannounced improvements and/or changes in the product and/or associated programs. Start Italiana S.r.l. is not liable for damages of any kind, including those resulting in the document, including typographical errors. Making copies, citing quotes or other reproductions of all or part of this document is permitted only after written consent of Start Italiana S.r.l. Trade mark or name is protected by patents. Copyright 2015 Start Italiana S.r.l. All rights reserved 2 GENERAL WARNINGS Before working on this equipment, please carefully read this instruction in this manual. Authorised and trained personnel must perform configuration changes and updates. The manufacturer is not responsible for any operation performed which is not covered in this manual. Any tampering with the equipment and software relieves the manufacturer of any responsibility in regards to competent bodies. In case of failure or defect, refer to an authorized service provider or manufacturer directly. The manufacturer accepts no responsibility for any injury and/or damage to persons and/or property and/or pets caused by failure to follow instructions relating to safety. Qualified and trained staff must have an understanding of the safety requirements mentioned in this manual, the user manual and in the installation manual. In case of doubt concerning the operation of the equipment refer to an authorized service provider or manufacturer directly. Rev. 09, April 2016 Page 4 of 28

5 Configuration Manual Login Procedure 3 INTRODUCTION This manual has been prepared in accordance with IEC standards Preparation of instructions for use - Structuring, content and presentation - Part 1: General principles and detailed requirements and according to the ATEX Directive 94/9/EU concerning equipment and protective systems intended for use in potentially explosive atmospheres. The manual provides necessary information on using a Maglink LX console. The following table lists the symbols used in the document: Symbol Description ATTENTION: Important information and notes regarding operations and use considerations IMPORTANT: Danger to persons (including death), to property or to the environment The following table lists reference data of the manufacturer: Data Name Address Description START ITALIANA S.r.l. Via Pola Bovisio Masciago (MB) Italia Telephone Fax Website support@startitaliana.it ATTENTION: This manual must be used in conjunction with the following manuals: Installation manual User Manual In order to use the console as described below in this manual, you must have installed the consoles as per installation manual and use the console as per the user manual ATTENTION: This manual must be used in conjunction with safety instructions: IMPORTANT: Console installation should be performed by qualified personnel, as shown in the Installation Manual and according to safety instructions Rev. 09, April 2016 Page 5 of 28

6 Configuration Manual Login Procedure The Maglink LX console complies with the requirements of Directive 2012/19/EC on waste of electrical and electronic equipment (WEEE) and hence displaying the according symbol: IMPORTANT: The crossed out wheelie bin symbol indicates that the product must be disposed at the end of its useful life with household waste and must be brought to a collection point for electrical and electronic equipment ATTENTION: The units of measurement contained in this manual refer to a specific choice by the user himself/herself. You can set the measurement units in a different way (see Section 6.1 of this manual) The Web Console Config is a web application installed on Supra Linux Apache Web Server operating system distributed with each MagLink LX. The web application is designed to configure and set parameters in the console. In addition, you can also display a variety of information: The status of all connected tanks The data on the shift report Historical data collected Reconciliations Current and previous alarms Delivery and losses To access the application you must know the IP address of the console (default: ) and type it into a browser (for example, Mozilla Firefox, Google Chrome, Internet Explorer, etc.). The following figure shows the home page of the Web Console Configuration:, as a first step, you need to select the display language: The possible display languages are as follows: Bosnian Czech Hungarian (Magyar) Romanian Slovenian Bulgarian English Italian Russian Spanish Chinese Simplified, Chinese French Polish Serbian (Cyrillic and Latin) Turkish Traditional Croatian German Portuguese Slovakian Ukrainian After selecting the language, press the "Select" button and the application displays the login page. Rev. 09, April 2016 Page 6 of 28

7 Configuration Manual Login Procedure 4 LOGIN PROCEDURE The following image shows the "Login Page": You can login as a "Guest" user or as an "Admin" user (The user has permission to access configuration pages to obtain common parameters and system parameters relating to the system setup). The following table shows the data displayed depending on the type of log on access: Accessible data Guest Admin Level of the connected probes X X Historical Data Table X X Alarm status X X Delivery/Losses X X Login X X Logout X X Association of alarm to relays (per tank) X Managing internal and external sensors X Automatic print features X Definition and insertion of strapping table (per tank) X Configuring address book X Configuration of all dispensers X TCP/IP address configuration X Utility operations (Backup/restore, Clean historical data: Historical readings, alarms, reconciliation, shift reports, Touch screen calibration of the console; Restarting the console, Restarting the operating system of the console) X Reconciliation (if enabled) X Shift report with scheduling X Configuration internal/external sensors X Sensors current status X X Modem configuration X Print stock at predefined time of the day X Rev. 09, April 2016 Page 7 of 28

8 Configuration Manual Login Procedure By accessing the application as "Admin" user you can perform configuration changes and navigate between pages. The following table shows the default passwords corresponding to the different types of login access: Login access Password Guest Admin You can only change the password by logging in as "Admin. GUEST-LX MAGLINK-LX ATTENTION: The administrator must change the password as soon as possible to prevent unauthorized access ATTENTION: Please be aware that the password is case sensitive All configuration data can be changed only after you have logged in as "Admin. The user must select the type of login access: "Guest" or "Admin enter password and press the "Access" button. Rev. 09, April 2016 Page 8 of 28

9 Configuration Manual Basic Functions 5 BASIC FUNCTIONS Once logged in you must enter the application, all pages have the same format. Menu items and user accessibility is displayed in the main menu at the top of the page as shown in the following examples: Log on as "Guest": Main menu Log on as "Admin": Main menu The following items are always present: Menù buttons on every pages Logo (Returns you to the home page) Name of the current page Type of access ("Guest" or "Admin") Current date or time Web versions, console and serial number From any page you can go to home page to change language for web application simply by clicking on the logo displayed after the last main menu button. The name of the page you are on is displayed on the top left. All configuration data can be modified after you have logged in as "Admin" user. To access the user must select the access type, "Guest" or "Admin, enter your password and press the "Login" button. Parameter changes are committed to the console only after pressing the "Apply configuration" button present in all pages. Rev. 09, April 2016 Page 9 of 28

10 Configuration Manual "Guest" and "Admin" pages 6 CHANGE PASSWORD The first thing to do is change the password for both "Guest" and "Admin" users. Only the "Admin" user can make password changes. Apply the following procedure: Step Description 1 Login as "Admin" 2 Press "Login" on the main menu It opens the "Login" page with the ability to change your password: 3 4 Press the "Change password" button Type the current password and the new password then press the "Confirm" button: 5 The application displays the result of the operation, displaying one of the following messages: 6 7 Repeat the operation in case of an incorrect input or contact your administrator if you forget your password. In the event that you are no longer able to recover the current password follow the procedure for resetting passwords. Rev. 09, April 2016 Page 10 of 28

11 Configuration Manual "Guest" and "Admin" pages 7 THE "GUEST" AND "ADMIN" PAGES 7.1 History The following image shows the "History Page": The page contains the saved data at regular intervals in a log file for future analysis. You can select from the following filters: Year/Month Day Tank Pressing the button "Display tank tank" displays the data with the considered filters. The button allows you to download data in Excel CSV format; the downloaded file contains all the information of the selected day. 7.2 Alarms The following image shows the "Alarms Page": Rev. 09, April 2016 Page 11 of 28

12 Configuration Manual "Guest" and "Admin" pages The page shows alarm history. You can select from the following filters: Tank Start date End Date Pressing the button "View Alarms" displays the data with the configured filters. The alarms are colour coded according to the current state: Green: For solved alarms Yellow: For acknowledged alarms Red: For alarms in progress 7.3 Delivery/Losses The following image shows the "Delivery/Losses Page": The page shows the Delivery data (White background colour lines) and related losses (Red background colour lines) as shown in the legend in the upper right corner above the table: The page shows "Delivery/Losses" history. You can select from the following filters: Tank Start Time End Time Pressing the button "Delivery/Losses" displays the data with the considered filters. The button allows you to download data to Excel (CSV) the created file contains all the information of the selected filter. Rev. 09, April 2016 Page 12 of 28

13 Configuration Manual "Guest" and "Admin" pages 7.4 Current Status The following image shows the "Current Status" page: The page allows you to view all the data sent by the probes connected to the console. The following filters are possible: All tanks: Data of all tanks is displayed one after the other 1,, 32: The selected tank data is displayed The page is reloaded automatically every minute and shows the latest information. You can refresh the page by pressing the F5 key, or by pressing the "Current Status" button from the main menu. ATTENTION: The displayed data refers to the latest data saved in the history file. 7.5 Sensor status This is the sensor status page. User can check current internal/external sensor status. Rev. 09, April 2016 Page 13 of 28

14 Configuration Manual "Admin" Pages 8 THE "ADMIN" PAGE 8.1 System The following image shows the "Systems Page": The page displays system information and parameters applied to all connected probes. The following table lists the parameters that can be set: Parameter Description Total tanks Number of connected probes (From 1 to 32) Total dispensers Number of connected dispensers (From 1 to 32) Total Slaves Sensors Protocol Type TCP Port Temperature of comp. volume Station name (Reserved for future use) (Reserved for future use) Select from among the following: DIALOG GILBARCO DOMS ORPAK FUEL POS PIGNONE Gilbarco protocol via TCP RETALIX Probe emulation Selectable values for the calculation of the compensated volume: 15 C 20 C Station name History range Time interval between a history saving data ATTENTION: It is highly recommended to set the value to 1 minute Probe sensitivity Language Measurement unit Date format Auto Print Allow setting the value to 0.5 ATTENTION: Do not change unless instructed by Start Italiana S.r.l. Select the language of the console display Select from among the following: mm/litre inches/gallon mm/gallon Select from the following date formats: yyyy-mm-dd dd-mm-yyyy MM-dd-yyyy Select when to perform the following automatic stamp: Shift report, at the beginning and end Losses, upon detection of a loss Alarms, at every status change Reconciliation, set the "Time" for reconciliation Delivery, at the beginning and end Rev. 09, April 2016 Page 14 of 28

15 Configuration Manual "Admin" Pages Manual Fairbanks You can download the PDF of the three manuals regarding the console: User Installation Configuration FTP configuration parameters used to upload data to Fairbanks servers The lower part of the page displays the configuration of the dipswitches. The following table shows the configuration of the dipswitches: Dipswitch Description 1 OFF = Single Gilbarco, ON = Double Gilbarco 2, 3, 5, 8 Not used 4 OFF = Relay in normal mode, ON = Relay in reverse mode 6 Resetting password (Turn off console, switch bit 6 to ON, turn on console, wait for the display cursor in the top left, turn off console, switch bit 6 to Off, turn back on console) ATTENTION: The password reset results in loss of all configuration data, the historical, alarms, delivery and reconciliations 7 OFF = Reconciliation deactivated, ON = Reconciliation activated Rev. 09, April 2016 Page 15 of 28

16 Configuration Manual "Admin" Pages 8.2 Tank The following image shows the "Tank Page": The page allows you to set the data of each tank; Select from the drop down "Tank, for the tank you wish to work on and then set the parameters listed in the following table: Parameter Enabled Description Address Product Type Density Total capacity* Maximum height* Offset Zero water Probe type Very high alarm, High alarm, Low alarm, Very low alarm, Water alarm Delta vol., Delta leakage Working Capacity DVD Configuration Description When the flag is active, the application queries the corresponding probe during the read cycle, otherwise the probe is not queried Description of the tank Address of the probe (no reading from probe in case of incorrect address) Select the type of product contained in the tank from the list Product density, fixed value defined by the product type selection Maximum volume of the product (read-only value) Maximum level of the product (read-only value) Value used to calibrate the position of the product float Possible values: ± mm Value used to calibrate the water float Resolution: 1 mm. Maximum value: mm Select from the following (This decision impacts the diagnostics display page on the console, refer to the user manual): Laser probe Logger Normal RF Set alarm values relating to different thresholds Set the minimum values to trigger a loss or leakage Set the working capacity for the Ullage calculation ID, offset and Maximum Confidence probe (Data provided by Start Italiana S.r.l.) *This parameter cannot be set, it is taken from the last line of the strapping table (See Strapping Table section); In case of no Strapping Table, it is possible to create a simple one, with only two lines: mm 0 litres 0 Add row mm Maximum height of tank litres Maximum volume capacity Add row Rev. 09, April 2016 Page 16 of 28

17 Configuration Manual "Admin" Pages 8.3 Strapping Table The following image shows the "Strapping Table Page": The Strapping table is used to calculate the volume of the tank, given that each tank has its own shape and its own height. After selecting the tank from the "tank" drop down, you can enter the information table in three different ways: 1. Create table manually: This method allows you to generate a complete linear table where the user must enter the switch from one level to the next. The table is created taking into account the total height of the tank. Press the button "Create new Information Table the table is generated and displayed on the right side of the page. Only level values are compiled the user must enter the values of the corresponding volume. Once generated the user can add new ones, change existing ones and/or deleting some with discretion: Add: Set the value in mm and litres and press "Add new line." Edit: Set the desired level (mm) and/or the volume (litres) for rows to edit Delete: Check the box next to the "Delete" button if you want to delete the entire Strapping table or put a check on lines to be deleted after finishing ticking all the lines press the "Delete" button 2. Import Table: When you have a Strapping table in Excel (CSV format) you can import it by using the "Choose File" and "Load" button. The table appears on the right side of the page 3. Duplicate table: It is possible to duplicate the Strapping Table of a tank for other tanks, one tank at a time. The source tank is selected from the "tank" drop-down list. The target tank is selected from the drop down "Destination Tank. Pressing the "Duplicate" button will duplicate the Strapping table from source tank to destination tank. Duplicating a table is saved automatically for the destination tank Additional buttons on the table: Validation of Strapping Table: During data entry you can check the consistency of the data entered by pressing this button in case of error or omission the corresponding lines are shown in bold red Save Strapping Table: At the end of any changes press the button to save the data. Cancel changes to Strapping Table: By selecting cancel changes you can undo all the changes made and start again. After entering the information table and/or having made any changes to the existing ones press the "Apply changes made to tables" button to take effect, otherwise all changes will take effect the next time you restart the application or the console itself. Rev. 09, April 2016 Page 17 of 28

18 Configuration Manual "Admin" Pages ATTENTION: Press the "Save strapping table" button to apply the changes; Otherwise, the changes are lost. ATTENTION: The strapping table can have a maximum of 500 points The button allows you to download the "Strapping Table" in an Excel file in CSV format. 8.4 Relays The following image shows the "Relay Page": Configuring alarm relays, select the tank from the "tank" drop-down list and wait for data to load, then set the desired alarms. Relays can be configured for the following: Not used Low Very high Water No link Out of range Very low High Probe Communication ATTENTION: When using the DVD, do not use Relay 4 as its used to power the DVD 8.5 Sensors In this section user can configure internal and external sensors. User must select a sensor type and for each sensor define the alarm status. In addition user can select a relè to combine with each sensor when alarm is active. You can specify the sensors connected to the console. Select the sensor from the "sensor type" drop-down list and fill in the fields related to sensors. The types of sensors available are as follows: Internal: Internal probe (6 sensors) Triple-state: Triple-state probe (64 sensors) External Card Start Italiana S.r.l.: External card supplied by Start Italiana S.r.l. (up to 32 sensors) The following image shows the "Sensors" page (Internal sensor type): Rev. 09, April 2016 Page 18 of 28

19 Configuration Manual "Admin" Pages The following image shows the "Sensors" page (Probe type "External Card Start Italiana S.r.l. ): Rev. 09, April 2016 Page 19 of 28

20 Configuration Manual "Admin" Pages The following image shows the "Sensors" page ("Triple-state sensor type"): 8.6 Reconciliation The following image shows the "Reconciliation Page": When connected to an FCC (Forecourt Controller) or POS enabled for reconciliation the console receives information on the amount of fuel dispensed. The user can compare the dispensed volume ("Dispenser" column) by the hour, with the difference in volume per hour detected by the probe ( Vol. Diff." column) The result is shown in the "Delta vol." column. ATTENTION: Reconciliation is not handled during Delivery: The table will not include the corresponding line of the Delivery time The button allows you to download the "Reconciliation" in an Excel file in CSV format. Rev. 09, April 2016 Page 20 of 28

21 Configuration Manual "Admin" Pages 8.7 Shift report The following image shows the "Shift report Page": The table shows the start and end of each shift report, select the "Day" and "Tank" values. You can establish an automatic scheduling of the shift report. From the "Time" drop-down list select one of the options then press the "Add schedule" button. To delete a schedule select from the "Shift Schedule" drop-down list a schedule and press the "Delete selected" button. The button allows you to download the "Shift report" in an Excel file in CSV format. 8.8 Dispenser Configuration The following image shows the "Config. Page": Dispensers": When the console is connected to an FCC or POS enabled for reconciliation configure the dispensers and its nozzle s associating them to the tanks from which they connected. For each dispenser you must define the number of nozzles and the tank it is connected to. Select from the "Dispenser" drop-down list the dispenser, to configure select the number of nozzles connected from the "nozzle" drop-down list, finally for each nozzle select the corresponding tank. 8.9 TCP/IP Connection The following image shows the "TCP/IP Page": You can access the TCP/IP parameters of the console: Address: IP address and communication port to communicate with the configuration application via a browser (Internet Explorer, Mozilla Firefox, Google Chrome, Opera, etc.) Netmask Rev. 09, April 2016 Page 21 of 28

22 Configuration Manual "Admin" Pages Gateway ATTENTION: The parameters of the "TCP/IP" page must be modified carefully; The IP address cannot be assigned to another device or computer of the same network Configuration The following image shows the "Config. Page": You can send notifications by . When the console changes state or it enters in Delivery mode an e- mail to the address list is sent. ATTENTION: Carefully configure the SMTP settings in "SMTP Configuration, then press the "Save SMTP" button In the "Address List" section, you can add a new by pressing the "Save new address" button or delete an existing by pressing the "Delete selected address Print Stock Configuration The following image shows the "print Stock configuration page": In this page it s possible to configure several hours a day for automatic print stock. A printer has to be connected and Double Gilbarco protocol has to be deactivated Rev. 09, April 2016 Page 22 of 28

23 Configuration Manual "Admin" Pages 8.12 Modem configuration settings As option is possible to insert a GSM modem card. It is possible to receive automatic notification or texting an SMS to the modem it will reply with the stock. Phone number configuration for SMS It is possible to select up to 3 telephone numbers to which address the following alert messages: console startup delivery parameter leakage parameter change tank status (alarms H, HH, L, LL, Water) both for enabled and disabled alarms IMPORTANT!: write the mobile phone number complete of the area code without spaces. Example: or Connection of the GSM modem Basic operations: 1. Disable the PIN code from the SIM card before insert it into the modem. 2. Insert the SIM card into the dedicated slot of the modem 3. Power on the console and wait some time to allow to the modem to connect to the GSM network. When connected the GSM signal depth will appear on the display of the console. The GSM modem will automatically send the alarm messages listed above when occur. Sending SMS to the console The text of the message sent to the console must include only 3 characters. Important: Always write T in capital letter Always write 0 before the number of the tank from 1 to 9 (for example 01 for tank 1) T00: shows the status of all connected tanks. Txx: xx refers to the number of the tank (for example T01) and shows the status of a specific tank. The console will answer to this message showing the reported values. Examples: Rev. 09, April 2016 Page 23 of 28

24 Configuration Manual "Admin" Pages 8.13 Utility The following image shows the "Utility" page: The following table lists the parameters on the page that can be set: Parameter Update date/time of the console Description Change the date/time, paying close attention to the proposed format respecting the locale; Date and time are used to store data in the console; When editing is finished, press "Save" Press the button "Calibrate" in the event of loss of screen accuracy; The following message appears: Touch Screen Calibration Restarting the console program System Reboot Shutdown application Reset to factory default Configuration Backup/Restore Delete data Follow the instructions on the console screen, by pressing the indicated position to complete the calibration process. When the procedure ends, the application starts automatically. Press the "Restart application" button Press the "System reboot" button to reboot the operating system Press Shutdown application to close application Press the "Reset" button Backup function - once the console has been installed and configured it is recommended to use this function to create a system back up, please note the system will keep the last back over writing any previous back-ups already made. If a USB stick is present the system will also create a backup on the stick. The restore function takes the data of the previous backup in the console; use the "Restore" button. If the user connects the console to a USB device with a previous backup and then presses the "Restore" button, the procedure searches for the previous backup data in the connected USB device and uses restore to back up if available. If no backup is found in the USB device, data for recovery is taken directly from the console. You can delete the following data: Alarms History Reconciliation Shift report Select data to be deleted and then press the "Clear" button. Rev. 09, April 2016 Page 24 of 28

25 User Manual Revisions 9 SUPPORT If you need direct assistance from a Start Italiana S.r.l. technician s the best solution is to connect the console to the Internet. Configure the router assigning console private IP address to a public IP address of the company, thus opening port 22 for console access and port 80 for web access. In this case the console can then be viewed directly by Start Italiana S.r.l. staff. An alternative is to use third-party programs (for example, Team Viewer 7 that can be downloaded from our website under the heading Assistance/Support) to allow a connection between remote computer (the console must be connected to the computer to which Start Italiana S.r.l. will connect remotely). In the case no Internet access is available the user can provide Start Italiana S.r.l. with console data to debug on. The following table shows the necessary procedure steps for the provision of such data: Step 1 Description Provide a USB device with at least 50 MB of free space available ATTENTION: The USB device must be formatted according to FAT32 2 Connect the USB device to a PC 3 Create a folder on the USB device named "lx-support"(all in lower case) 4 Connect the USB device to the console 5 Press the "INFO" button and access the relevant page 6 7 Wait until the "Export Log" appears on the screen and then press it (The files are copied to your device in the console) Perform a compression of the "lx-support" folder and send the ZIP file by to support@startitaliana.it Rev. 09, April 2016 Page 25 of 28

26 User Manual Revisions 10 REVISIONS The following table lists the revisions to the document: Revision No. Date Description Firmware Revision 01 March 2014 First version February 2015 Reversing the com port March 2015 Addition of an application description section April 2015 Addition of a Certification Section and a Notification Section 2.1.x 05 April 2015 New test reports, certification and notification 2.1.x 06 July November 2015 Manual updated procedure, information reconciliation, shift reports, stock printout, sending log information to the media, program description Addition of page for probe manager, addition of shift report scheduling, addition of automatic printing features, manual layout revision, updated legends of dip switch 2.2.x 2.3.x 08 January 2016 Translation 2.3.x 09 April 2016 Modem GSM enabled, Working capacity, Auto Print Stock Rev. 09, April 2016 Page 26 of 28

27

28 START ITALIANA S.r.l. Via Pola Bovisio Masciago (MB) Italia Tel Fax support@startitaliana.it