Application Software Release Notes ED

Transcription

1 Application Software Release Notes ED Intelligent Equipment Author: Michael Lyga Software Version: Release Date: May 2018 Supercedes: ED ED ED ED ED Table of Contents Release Version Equipment Page Additions Major Changes Minor Changes...2 Release Version Equipment Page Additions Major Changes Minor Changes...2 Release Version Equipment Page Additions Major Changes Minor Changes...3 Release Version Equipment Page Additions Major Changes Minor Changes...4 Release Version Equipment Page Additions Major Changes Minor Changes...6 Release Version Equipment Page Additions Major Changes Minor Changes...7 Release Version Equipment Page Additions Major Changes Minor Changes...8 Release Version Equipment Page Additions Major Changes Minor Changes...9 Release Version Equipment Page Additions Major Changes Minor Changes...9 Release Version Equipment Page Additions Major Changes Minor Changes...10

2 Release Version Release Date: 05/09/ Equipment Page Additions Magnitude Magnetic Bearing Water-Cooled Centrifugal Chiller (WMC-D), both single compressor and dual compressor. IE Gateway-on-the-Go hardware kit is required. Trailblazer Air-Cooled Scroll Chiller (AMZ). IE Gateway-on-the-Go hardware kit is required. 1.2 Major Changes Trends: More points are supported in the trends view for all equipment. Alarms: Reduced the delay to immediate alarm notifications. Release Version Release Date: 2/6/ Equipment Page Additions No new equipment added in release. 2.2 Major Changes General performance enhancements have been made to the release. 2.3 Minor Changes Several other minor bug fixes and enhancements have been made to the release. 1.3 Minor Changes Several other minor bug fixes and enhancements have been made to the release. ED INTELLIGENT EQUIPMENT 2

3 Release Version Release Date: 11/15/ Equipment Page Additions No new equipment added in release. Added support for the Intelligent Equipment Express solution. IE Express is a retrofit kit without the Energy Management Module (EMM). It provide access to information about the equipment (status, setpoints, and configuration), but there is reading of energy consumption. Added support for the Intelligent Equipment Gatewayon-the-Go solution. This solution is designed as a service tool for the field technician to temporarily install on the equipment for troubleshooting purposes and short term monitoring of equipment status, setpoints, and configuration settings. This option does not include the EMM for energy monitoring. Once an issue is resolved or the job is finished the tech can remove it and use it on the next equipment that needs troubleshooting. This is similar to IE Express, but is designed for temporary only use as a service tool. 3.2 Major Changes Alarms: Addressed the issue where Intelligent Equipment was incorrectly generating a communication down alarm from the gateway or unit controller 3.3 Minor Changes Several other minor bug fixes and enhancements have been made to the releas ED INTELLIGENT EQUIPMENT 3

4 Release Version Release Date: 6/7/ Equipment Page Additions Pathfinder Air-Cooled Chiller (AWS) with single point power and the MicroTech III controller. 4.2 Major Changes Help page: A copy of the License Agreement is added to the IE Help Documents tab in the Help page. These are the terms agreed a first time user agrees to when they access the software and create their profile. The Help page is accessible from the User Profile menu or the question mark (?) link next to the User Profile for quicker access. Technician / Technician Admin Role: Graphics - Roofpak units: Default images are added for Roofpak units on the Overview, Air, and Refrigeration tabs. Analytics: Added Compressor Health section to the Circuit tab for chillers. This new section compares the RunTime (hr) vs. Compressor Starts for each compressor in the circuit for the following time periods: Lifetime of the compressor Past year Past month Past week Last stop this is the just the run time the last time the compressor ran. The status of the time periods for the RunTime (hr) vs. Compressor Starts are color coded to show quality of this analytic: Red if the result < 1 hr/start Yellow if the result >= 1 hr/start and < 2 hr/ start Green if result >= 2 hr/start Maintenance: Event Based notifications is improved to now support chiller attributes. Event Based notifications can be setup to trigger based on up to 3 conditions (using the AND operator). Reports: Chiller Inspection Report: This report, which was added in the 2.2 release for AGZ, is now available for the AWV Pathfinder. This report, allows the tech to do diagnostics & make recommendations, point out the benefit to any available enhancements and document the operational data during the inspection. Select operational data is autopopulated into the inspection report from the Micro-Tech controller. Saves the technician time for checking data locally at the site. Diagnostics menu allows all major components such as compressor, oil, evaporator, condenser, and electrical system components to be evaluated based on pre-configured inspection checks and low and high severity inspection warnings. This feature is located on the equipment page. Click the Maintenance tab and then the Diagnostics sub tab to complete & submit the report. Click the Reports tab and then the Service Logs sub tab to download/ view the document after the report is submitted. Enhanced Trend Charts: Added a bivariate, which allows the user to define their own variable on the x-axis. To change a chart from a time-based chart: Click on the Setup Trend button. Select the Bivariate option instead of the Time option. Select a point for the x-axis and a point for the y-axis. Customer / Customer Admin Role: A new bar chart called Energy Cost is added to show the cost associated with the energy usage for the specified time period. This chart provides the following information: Y-axis: left side shows energy usage, right side reflects the cost. Chart header shows the total energy and total cost for the specified time period. Overlay previous week. Ability to download the presented data to CSV, PNG, JPEG, PDF, and SVG file format. 4.3 Minor Changes Several other minor bug fixes and enhancements have been made to the release. ED INTELLIGENT EQUIPMENT 4

5 Release Version Release Date: 1/9/ Equipment Page Additions Pathfinder Air-Cooled Chiller (AWV) with single point power and the MicroTech III controller. 5.2 Major Changes Onboarding Wizard: New Users improved first time access to the user interface by taking new users directly to their setup page (User Profile Settings menu), so they are aware of how their alarm & maintenance notifications are setup and if necessary can change the settings to appropriate nuisance frequency. Existing Users the Customer/Technician login screen indicates whenever a new unit has been assigned to you by showing an asterisk (*) next to role (Customer and/or Technician) and a note to remind the user to verify the schedule and notifications for the new unit(s) is setup correctly under the Settings page. Technician / Technician Admin Role: Discharge Air Temperature (DAT) Reset: DAT Reset is added for rooftop units under the Controls tab, giving you the ability to determine how the heat/cool reset is controlled, what heat/ cool temperature it is set to, and the min/max the heat/cool temperature can reset to. Enhanced Setpoints Override status to more clearly indicate when a unit is in overridden or if an override is canceled due to an external source like a BAS. This feature is located on the equipment page. Click on the Controls tab and then the Setpoints Override sub tab. Alarm Log: Added ability to export the alarm log to a comma separated value (CSV) file. Added Orange color to indicate when an alarm type is a Problem alarm type. Alarm color scheme is now as follows: Unit Controller Alarms Warnings = Yellow Problems = Orange Faults = Red Intelligent Equipment alarms Unit Not Commissioned = Yellow Gateway Communication to Cloud Down = Red Reports: Export Data tab Enhanced the Time Period range to include the date & time range instead of just the date range. Data can be exported based on three(3) formats: Data Unit Log file Fixed Time Trend Change of Value Graphics - Large Rebel units: Default images exist for all Large Rebel units, not just the ones 25 tons or greater. Customer / Customer Admin Role: A new pie chart called Run Time is added to show amount of time a unit is in different modes (e.g., 100hrs heating, 500hrs cooling, 300hrs off, etc.). A new line chart called Energy Usage replaces the previous Live Power Usage data to provide more useful information about the energy used by the equipment. The chart also allows you to plot the values to the previous date range set in the chart for easier comparison of energy usage. Data can be plotted for the last Day, the last Week, the last Month, and the last Year. NOTE: the last Week, Month, & Year are the last periods relative to the current date, not the last calendar week, month, or year. That means: Last Day = the last 24 hours, not the previous calendar day Last Week = the last 7 days, not last Monday-Sunday. Last Month = the last 30 days, not the last calendar month Last Year = the last 365 days, not the last calendar year The Show Previous XX checkbox shows the previous time period to the last day/week/month/ year selected. Example; if today is Wednesday, 12/14/16, then the Week button will show the data from 12/8/16 12/14/16. If I select the Show Previous Week checkbox then previous week s data from 12/1/16 12/7/16 will plot as a separate line on the chart. Enhanced the fields in the Customer view, so all fields are their own app within the UI, to improve flexibility of the layout. ED INTELLIGENT EQUIPMENT 5

6 The following apps can be shown/hidden using the Settings icon on the Customer page. Note that some apps are not supported by every equipment type: Alarm Status Comfort Index Energy Usage (new; see description above) Financial Summary Performance Index Run Time (new; see description above) Weather Building Status Energy Star (if Energy Star is enabled) Equipment Metrics Maintenance Resources Sustainability Index (if Energy Star is enabled) 5.3 Minor Changes Several other minor bug fixes and enhancements have been made to the release. Release Version Release Date: 06/30/ Equipment Page Additions Trailblazer Air-Cooled Chiller (AGZ-D/E) with single point power and the MicroTech III controller. 6.2 Major Changes Added Help page: Help page is accessible from the User Profile menu or the question mark (?) link next to the User Profile for quicker access. There are three tabs: Intelligent Equipment Help Documents Intelligent Equipment Videos Intelligent Equipment Release Notes Technician/Technician Admin Role: Reports Chiller Inspection Report: New chiller support includes ability to submit a chiller inspection report, which allows the tech to do diagnostics & make recommendations, point out the benefit to any available enhancements document the operational data during the inspection. Select operational data is auto-populated into the inspection report from the Micro- Tech controller. Saves the technician time for checking data locally at the site. Diagnostics menu allows all major components such as compressor, oil, evaporator, condenser, and electrical system components to be evaluated based on preconfigured inspection checks and low and high severity inspection warnings. This feature is located on the equipment page. Click the Maintenance tab and then the Diagnostics sub tab to complete & submit the report. Click the Reports tab and then the Service Logs sub tab to download/ view the document after the report is submitted. Operational Activity & Settings Change Report: Enhanced the report to include when users log into Intelligent Equipment. ED INTELLIGENT EQUIPMENT 6

7 Access to writable points: Tech Admin has ability to define the level of access a technician has to equipment. This is a system-level setting and therefore applies to all equipment the user is assigned to. Setpoints only (default) Configuration points only Both None (writeable point are read-only) Added Setpoints Override capability for rooftop units so the user can customize setpoint overrides for occupied and unoccupied periods. This feature is located on the equipment page. Click on the Controls tab and then the Setpoints Override sub tab. Allows the user to override the schedule for temporary periods of time increasing flexibility for comfort adjustments and to save energy by defaulting back to the schedule when the event expires. Time Duration can be specified for a 1, 2, 4, or 8, 12, or 24 hour override duration. Allows user to comply with Title 24 and other energy codes. Enhanced Commission/Recommission feature: Added the ability to indicate if the commission process was already done prior to installing Intelligent Equipment on the unit, so that the tech does not have to repeat the commissioning work in order to monitor the equipment from Intelligent Equipment. Only a subset of the fields is required to submit a commissioning report, instead of every field. Previous settings are saved improve the ease of doing a recommission. Added ability to start and save progress of the commissioning process without submitting the report. User has 30 days from the time the commission process is started to submit their progress before the user must start over. Enhanced Trend Charts: Improved ability to more easily show/hide points in the point list on the Trend View page. Added left/right arrows for scrolling when chart is zoomed in. Out of range is hidden in legend if no values are out of range. Alarm Log: Added ability to filter by date range. Enhanced Maintenance functionality by adding the following features: Event Based item can be setup to trigger based on up to 3 conditions (using the AND operator). Default maintenance periods for rooftops are updated so actions fall into 3 periods instead of 6: All Weekly actions are moved to the Monthly, Quarterly (renamed Four times a year ) and Annual periods. All Bi-monthly actions are moved to the Quarterly (renamed Four times a year ) and Annual periods. All Twice-A-Year actions are moved to the Annual period. Customer/Customer Admin Role: Customer view is simplified to include sections that are relevant to the equipment associated with the site. Made it easier to opt out of the Energy Star when creating a site by explicitly adding the Opt Out option. Power calculations are now hidden when power attributes are not available. 6.3 Minor Changes Sites List page: An Admin user has ability to re-share a site hierarchy that was shared with them. Enhanced the paging functionality to include the option to show 100 items per page (previously the max was 50 items per page). Added a Leave Feedback at the footer so users have the ability to provide feedback at any time. Changed the yellow information box at the top of the pages, so its details are hidden until the user chooses to show the details (example, to see details about a subscription is about to expire or a unit s commissioning was started and must complete within 30 days before current work is reset). A new software release notification will appear when a user first logs into Intelligent Equipment after a software update. ED INTELLIGENT EQUIPMENT 7

8 Release Version Release Date: 12/2/ Equipment Page Additions No new equipment added in release. 7.2 Major Changes User Profile menu: Settings Alarm Schedules: Added more frequency options to the notification. It now has Never, Immediately, After 1 Day, After 2 Days, After 1 Week, and After 8 Days. Change the default schedule, so they are no longer set to notify all level of alarms immediately by default. It is now: Alarm Level Customer Role Technician Role Unit Warnings After 1 Week After 1 Day Unit Problems After 2 Days Immediately Unit Faults After 2 Days Immediately Gateway to Controller Comm Never Never Gateway Communication After 8 Days After 1 Week Alarm level settings now apply at the equipment level instead of based on a per user setting. Added the equipment serial number and address to the equipment details when setting up the alarm schedule. Added ability for user to unsubscribe from an alarm type (warnings, problems, faults, etc.) for all equipment associated with an Alarm Schedule. Notifications and Messaging: Enhanced the s so that similar/related s are grouped together as one versus sending each out individually. This reduces the number of s an individual receives. Welcome invitation and initial equipment access s are grouped in to one . Maintenance s for multiple equipment are grouped into one for the Technician role. Regularly scheduled site reports (e.g., quarterly reports) on all equipment are grouped into one for the Customer role. Regularly scheduled Maintenance reports (e.g., quarterly reports) on all equipment are grouped into one for the Technician role. Technician/Technician Admin Role: Settings page: Added ability to select which equipment properties/attributes to show/hide in the Trend View and Unit Details pages. Settings are per equipment. Added ability to rename attributes so the default presentation names are more understandable. Enhanced Trend Charts: Added ability to add multiple charts for each equipment. Added Sample Power data. Enhanced Maintenance functionality by adding a Maintenance/Diagnostic tab that provides access to the following features for rooftop units: Added Recommission equipment capability with the option to take a snapshot of the attribute values to optimize unit performance and cost savings. A Recommission Report is sent to the initiator. Technician Admins can also see the recommission history for the equipment. Added Automated Economizer Test feature using the dew point to confirm operation of the economizer dampers. Added Automated Refrigerant Test feature to confirm refrigerant charge. Added Code String to the Equipment page. Customer/Customer Admin Role: Added ability to show/hide the Energy Star related sections (Building Status, Sustainability Index, and Energy Star sections). Feature is located in the Building Info section. 7.3 Minor Changes Added Intelligent Equipment logo to top-right corner of all screens in the user-interface. Sites List page: Ability to add new equipment to sites that are already shared. If no sites are created in the My Site tab when logging into the system but there is a shared site in the Shared with me tab then the view will display the Shared with me view. Navigating back to the Sites List page will now return you to the last tab you were on ( My Sites or Shared with me tab). Export files: Rearranged order of some of the columns of data. Added the name of the attributes to better identify the properties in the file. Added the equipment time zone to the file name. Time stamps in the file are the times where the equipment is located. Now support alarm code 52 as warning with description Not economizing when available. Reports: Added Intelligent Equipment logo to reports. ED INTELLIGENT EQUIPMENT 8

9 Release Version Release Date: 5/19/ Equipment Page Additions No new equipment added in release. 8.2 Major Changes Different Maintenance list for different Unit types: Added ability to have different maintenance lists for different unit types so that the data on UI organizes according to unit types. Users now able to select points they want shown in the table in all Quick views. Event Based Maintenance improvement: Now notified that Change Filter - Dirty Filter maintenance is needed when corresponding alarm occurs and that Lubricate Supply/Return Fans maintenance is needed after 2,000 hours of unit operation so that the customer or technician can perform/request needed maintenance in time. Customer role: Added ability to move sections on Dashboard across sides so that the Dashboard is adapted for specific unit needs. The last positioning is saved for the Building and shown next time the user navigates to the Dashboard within during the session or new session. Energy Star: added a note for California and Mexico customers to clarify that the Energy Star values are calculated based on US data. Technician role: Previous export parameters are now stored to reduce time spent on setting parameters on the next export. 8.3 Minor Changes None. Release Version Release Date: 2/19/ Equipment Page Additions RoofPak (RAH, RDS, RDT, RFS, RPR, RPS) with the MicroTech III controller, single point power, and without a split condensing section. 9.2 Major Changes User Profile menu: Settings: Added ability to setup Alarm Schedules, Alarm Escalation Rules, and Maintenance Schedules. Change Role: Added this feature to the User Profile dropdown list to give user the ability to change their user role without first logging out. Sites List page: Added ability to share a site hierarchy with another user. Customer role: Added ability to integrate building and meter data between Intelligent Equipment and the ENERGY STAR Portfolio Manager. Added Building Report feature. Added Sustainability Index, Equipment Metrics, Financial Summary, and Performance Index. Improved the Comfort Index. Technician role: Added a Details view to the Site List page. Added ability to change time zone in the equipment. Added ability to upload building images in the equipment Overview Screen. Added functionality to request a parts quote from a service entity. Added functionality to modify default maintenance periods and to add custom maintenance items in the Maintenance screen. 9.3 Minor Changes Customer and Technician role: Enhanced Report functionality. Technician role: Enhanced document availability feature in the equipment Overview Screen. ED INTELLIGENT EQUIPMENT 9

10 Release Version Release Date: 10/22/ Equipment Page Additions Rebel (DPS) with single point power and the MicroTech III controller. Maverick II (MPS) with single point power and the MicroTech III controller Major Changes Created the following items as initial features, sections, & subsections in Intelligent Equipment: User Roles: Customer Administrator, Customer, Technician Administrator, Technician. Equipment Administrator For Internal-Use- Only. This is not a public accessible role; it is for corporate tech support use only). Customer role: Customer Administrator role has ability to create other Customer users in the system and add / remove their access at the equipment level. Sites page User Profile menu System Messages Create, edit, and delete a site hierarchy Site Messages Alarm Status Indicator Site Dashboard page Setup Meters HVAC Summary Building Info Weather Comfort Index Sustainability Index Energy Star Resources Technician role: Technician Administrator role has ability to create other Technician users in the system and add / remove their access at the equipment level. Sites page User Profile menu System Messages Create/edit/delete the site hierarchy Site Messages Alarm Status Indicator Quick View Unit Dashboard page Current Schedule Change Schedule Refresh Alarm Log Subscription Status Overview Screen Upcoming Maintenance Overview Info Documents Unit Overview Economizer Cooling Heating Power Air Screen Fan 100% Econ Unit Overview Sensors Setpoints Measured Calculated Operating Hours Refrigeration Screen Unit Overview Sensors Setpoints Operating Hours Supplemental Heat Screen Unit Overview Maintenance Screen Maintenance Info Log Maintenance Controls Screen Setpoints Screen Operations Screen Capacity Unit Overview Sensors Setpoints 10.3 Minor Changes None. Reference Materials Refer to the Intelligent Equipment Operations and Maintenance (OM) manuals for details about the added features and enhancements in the latest release. ED INTELLIGENT EQUIPMENT 10

11

12 Daikin Applied Training and Development Now that you have made an investment in modern, efficient Daikin equipment, its care should be a high priority. For training information on all Daikin HVAC products, please visit us at and click on Training, or call and ask for the Training Department. Warranty All Daikin equipment is sold pursuant to its standard terms and conditions of sale, including Limited Product Warranty. Consult your local Daikin Applied Representative for warranty details. To find your local Daikin Applied Representative, go to Aftermarket Services To find your local parts office, visit or call PARTS ( ). To find your local service office, visit or call This document contains the most current product information as of this printing. For the most up-to-date product information, please go to Products manufactured in an ISO Certified Facility. ED (05/18) 2018 Daikin Applied (800)